[ Upstream commit 7b900ead6c ]
We need to make sure, that the carrier check polling is disabled
while suspending. Otherwise we can end up with usbnet_read_cmd()
being issued when only usbnet_read_cmd_nopm() is allowed. If this
happens, read operations lock up.
Fixes: d69d169493 ("usbnet: smsc95xx: fix link detection for disabled autonegotiation")
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Raghuram Chary J <RaghuramChary.Jallipalli@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c7e86acfce ]
If the network becomes (partially) unavailable, say by disabling IPv6, the
background ACK transmission routine can get itself into a tizzy by
proposing immediate ACK retransmission. Since we're in the call event
processor, that happens immediately without returning to the workqueue
manager.
The condition should clear after a while when either the network comes back
or the call times out.
Fix this by:
(1) When re-proposing an ACK on failed Tx, don't schedule it immediately.
This will allow a certain amount of time to elapse before we try
again.
(2) Enforce a return to the workqueue manager after a certain number of
iterations of the call processing loop.
(3) Add a backoff delay that increases the delay on deferred ACKs by a
jiffy per failed transmission to a limit of HZ. The backoff delay is
cleared on a successful return from kernel_sendmsg().
(4) Cancel calls immediately if the opening sendmsg fails. The layer
above can arrange retransmission or rotate to another server.
Fixes: 248f219cb8 ("rxrpc: Rewrite the data and ack handling code")
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 85b18b0237 ]
The commit f77f0aee4d ("net: use core MTU range checking in USB NIC
drivers") introduce a common MTU handling for usbnet. But it's missing
the necessary changes for smsc95xx. So set the MTU range accordingly.
This patch has been tested on a Raspberry Pi 3.
Fixes: f77f0aee4d ("net: use core MTU range checking in USB NIC drivers")
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 96801552f8 ]
The CPU policer used to police packets being trapped via a local route
(IP2ME) was incorrectly configured to police based on bytes per second
instead of packets per second.
Change the policer to police based on packets per second and avoid
packet loss under certain circumstances.
Fixes: 9148e7cf73 ("mlxsw: spectrum: Add policers for trap groups")
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e1e4647984 ]
Different from processing the addstrm_out request, The receiver handles
an addstrm_in request by sending back an addstrm_out request to the
sender who will increase its stream's in and incnt later.
Now stream->incnt has been increased since it sent out the addstrm_in
request in sctp_send_add_streams(), with the wrong stream->incnt will
even cause crash when copying stream info from the old stream's in to
the new one's in sctp_process_strreset_addstrm_out().
This patch is to fix it by simply removing the stream->incnt change
from sctp_send_add_streams().
Fixes: 242bd2d519 ("sctp: implement sender-side procedures for Add Incoming/Outgoing Streams Request Parameter")
Reported-by: Jianwen Ji <jiji@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit df5a8ec64e ]
Up until commit 7e5fbd1e07 ("net: mdio-gpio: Convert to use gpiod
functions where possible"), the _cansleep variants of the gpio_ API was
used. After that commit and the change to gpiod_ API, the _cansleep()
was dropped. This then results in WARN_ON() when used with GPIO
devices which do sleep. Add back the _cansleep() to avoid this.
Fixes: 7e5fbd1e07 ("net: mdio-gpio: Convert to use gpiod functions where possible")
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit fd82d61ba1 ]
As defined in rfc6525#section-6.1.3, SCTP_STREAM_CHANGE_DENIED
and SCTP_STREAM_CHANGE_FAILED should be used instead of
SCTP_ASSOC_CHANGE_DENIED and SCTP_ASSOC_CHANGE_FAILED.
To keep the compatibility, fix it by adding two macros.
Fixes: b444153fb5 ("sctp: add support for generating add stream change event notification")
Reported-by: Jianwen Ji <jiji@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d02854dc19 ]
A null dereference was observed when a sysctl was being set
from userspace and rmnet was stuck trying to complete some actions
in the NETDEV_REGISTER callback. This is because the real_dev is set
only after the device registration handler completes.
sysctl call stack -
<6> Unable to handle kernel NULL pointer dereference at
virtual address 00000108
<2> pc : rmnet_vnd_get_iflink+0x1c/0x28
<2> lr : dev_get_iflink+0x2c/0x40
<2> rmnet_vnd_get_iflink+0x1c/0x28
<2> inet6_fill_ifinfo+0x15c/0x234
<2> inet6_ifinfo_notify+0x68/0xd4
<2> ndisc_ifinfo_sysctl_change+0x1b8/0x234
<2> proc_sys_call_handler+0xac/0x100
<2> proc_sys_write+0x3c/0x4c
<2> __vfs_write+0x54/0x14c
<2> vfs_write+0xcc/0x188
<2> SyS_write+0x60/0xc0
<2> el0_svc_naked+0x34/0x38
device register call stack -
<2> notifier_call_chain+0x84/0xbc
<2> raw_notifier_call_chain+0x38/0x48
<2> call_netdevice_notifiers_info+0x40/0x70
<2> call_netdevice_notifiers+0x38/0x60
<2> register_netdevice+0x29c/0x3d8
<2> rmnet_vnd_newlink+0x68/0xe8
<2> rmnet_newlink+0xa0/0x160
<2> rtnl_newlink+0x57c/0x6c8
<2> rtnetlink_rcv_msg+0x1dc/0x328
<2> netlink_rcv_skb+0xac/0x118
<2> rtnetlink_rcv+0x24/0x30
<2> netlink_unicast+0x158/0x1f0
<2> netlink_sendmsg+0x32c/0x338
<2> sock_sendmsg+0x44/0x60
<2> SyS_sendto+0x150/0x1ac
<2> el0_svc_naked+0x34/0x38
Fixes: b752eff5be ("net: qualcomm: rmnet: Implement ndo_get_iflink")
Signed-off-by: Sean Tranchetti <stranche@codeaurora.org>
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 12480e3b16 ]
According to rfc8260#section-4.3.2, SCTP_SS_DEFAULT is required to
defined as SCTP_SS_FCFS or SCTP_SS_RR.
SCTP_SS_FCFS is used for SCTP_SS_DEFAULT's value in this patch.
Fixes: 5bbbbe32a4 ("sctp: introduce stream scheduler foundations")
Reported-by: Jianwen Ji <jiji@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0432e83319 ]
Since 4.19 the following error in sysfs has appeared when using the
r8169 NIC driver:
$cd /sys/module/realtek/drivers
$ls -l
ls: cannot access 'mdio_bus:RTL8201F 10/100Mbps Ethernet': No such file or directory
[..garbled dir entries follow..]
Apparently the forward slash in "10/100Mbps Ethernet" is interpreted
as directory separator that leads nowhere, and was introduced in commit
513588dd44 ("net: phy: realtek: add RTL8201F phy-id and functions").
Fix this by removing the offending slash in the driver name.
Other drivers in net/phy seem to have the same problem, but I cannot
test/verify them.
Fixes: 513588dd44 ("net: phy: realtek: add RTL8201F phy-id and functions")
Signed-off-by: Holger Hoffstätte <holger@applied-asynchrony.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a9049ff921 ]
The mv88e6161 would sometime fail to probe with a timeout waiting for
the switch to complete an operation. This operation is supposed to
clear the statistics counters. However, due to a read/modify/write,
without the needed mask, the operation actually carried out was more
random, with invalid parameters, resulting in the switch not
responding. We need to preserve the histogram mode bits, so apply a
mask to keep them.
Reported-by: Chris Healy <Chris.Healy@zii.aero>
Fixes: 40cff8fca9 ("net: dsa: mv88e6xxx: Fix stats histogram mode")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit acf3766b36 ]
The mlx5e channels should be closed before mlx5i_uninit_underlay_qp
puts the QP into RST (reset) state during mlx5i_close. Currently QP
state incorrectly set to RST before channels got deactivated and closed,
since mlx5_post_send request expects QP in RTS (Ready To Send) state.
The fix is to keep QP in RTS state until mlx5e channels get closed
and to reset QP afterwards.
Also this fix is simply correct in order to keep the open/close flow
symmetric, i.e mlx5i_init_underlay_qp() is called first thing at open,
the correct thing to do is to call mlx5i_uninit_underlay_qp() last thing
at close, which is exactly what this patch is doing.
Fixes: dae37456c8 ("net/mlx5: Support for attaching multiple underlay QPs to root flow table")
Signed-off-by: Denis Drozdov <denisd@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f2b18732ee ]
The commit "net/mlx5: Refactor accel IPSec code" introduced a
bug where asynchronous short time change in hash key value
by create/release SA context might happen during an asynchronous
hash resize operation this could cause a subsequent remove SA
context operation to fail as the key value used during resize is
not the same key value used when remove SA context operation is
invoked.
This commit fixes the bug by defining the SA context hash key
such that it includes only fields that never change during the
lifetime of the SA context object.
Fixes: d6c4f0298c ("net/mlx5: Refactor accel IPSec code")
Signed-off-by: Raed Salem <raeds@mellanox.com>
Reviewed-by: Aviad Yehezkel <aviadye@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f8504f4ca0 ]
This issue happens when trying to add an existent tunnel. It
doesn't call sock_put() before returning -EEXIST to release
the sock refcnt that was held by calling sock_hold() before
the existence check.
This patch is to fix it by holding the sock after doing the
existence check.
Fixes: f6cd651b05 ("l2tp: fix race in duplicate tunnel detection")
Reported-by: Jianlin Shi <jishi@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Reviewed-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0d5b9311ba ]
Multiple cpus might attempt to insert a new fragment in rhashtable,
if for example RPS is buggy, as reported by 배석진 in
https://patchwork.ozlabs.org/patch/994601/
We use rhashtable_lookup_get_insert_key() instead of
rhashtable_insert_fast() to let cpus losing the race
free their own inet_frag_queue and use the one that
was inserted by another cpu.
Fixes: 648700f76b ("inet: frags: use rhashtables for reassembly units")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: 배석진 <soukjin.bae@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 64e2833484 ]
Querying interface FEC caps with 'ethtool [int]' after link reset
throws warning regading link speed.
This warning is not needed as there is already an indication in
user space that the link is not up.
Fixes: 0696d60853 ("net/mlx5e: Receive buffer configuration")
Signed-off-by: Shay Agroskin <shayag@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 228c4cd04d ]
Loopback test had fixed packet size, which can be bigger than configured
MTU. Shorten the loopback packet size to be bigger than minimal MTU
allowed by the device. Text field removed from struct 'mlx5ehdr'
as redundant to allow send small packets as minimal allowed MTU.
Fixes: d605d66 ("net/mlx5e: Add support for ethtool self diagnostics test")
Signed-off-by: Valentine Fatiev <valentinef@mellanox.com>
Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 83621b7df6 ]
We get the match level (none, l2, l3, l4) while going over the match
dissectors of an offloaded tc rule. When doing this, the match level
enum and the not min inline enum values should be used, fix that.
This worked accidentally b/c both enums have the same numerical values.
Fixes: d708f90298 ('net/mlx5e: Get the required HW match level while parsing TC flow matches')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 69fec325a6 ]
This reverts commit 22d7be267e.
The dst's mtu in transport can be updated by a non sctp place like
in xfrm where the MTU information didn't get synced between asoc,
transport and dst, so it is still needed to do the pmtu check
in sctp_packet_config.
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0073c8f727 ]
In case of striding RQ, we use MPWRQ (Multi Packet WQE RQ), which means
that WQE (RX descriptor) can be used for many packets and so the WQE is
much bigger than MTU. In virtualization setups where the port mtu can
be larger than the vf mtu, if received packet is bigger than MTU, it
won't be dropped by HW on too small receive WQE. If we use linear SKB in
striding RQ, since each stride has room for mtu size payload and skb
info, an oversized packet can lead to crash for crossing allocated page
boundary upon the call to build_skb. So driver needs to check packet
size and drop it.
Introduce new SW rx counter, rx_oversize_pkts_sw_drop, which counts the
number of packets dropped by the driver for being too large.
As a new field is added to the RQ struct, re-open the channels whenever
this field is being used in datapath (i.e., in the case of linear
Striding RQ).
Fixes: 619a8f2a42 ("net/mlx5e: Use linear SKB in Striding RQ")
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 077ecd785d ]
Currently, we are only supporting tc hw offloads when the eswitch
support is compiled in, but we are not gating the adevertizment
of the NETIF_F_HW_TC feature on this config being set.
Fix it, and while doing that, also avoid dealing with the feature
on ethtool when the config is not set.
Fixes: e8f887ac6a ('net/mlx5e: Introduce tc offload support')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d3a80bb5a3 ]
For the "all" ethertype we should not care whether the packet has
vlans. Besides being wrong, the way we did it caused FW error
for rules such as:
tc filter add dev eth0 protocol all parent ffff: \
prio 1 flower skip_sw action drop
b/c the matching meta-data (outer headers bit in struct mlx5_flow_spec)
wasn't set. Fix that by matching on vlan non-existence only if we were
also told to match on the ethertype.
Fixes: cee2648762 ('net/mlx5e: Set vlan masks for all offloaded TC rules')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reported-by: Slava Ovsiienko <viacheslavo@mellanox.com>
Reviewed-by: Jianbo Liu <jianbol@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 7ab412d33b ]
When a link failure is detected locally, the link is reset, the flag
link->in_session is set to false, and a RESET_MSG with the 'stopping'
bit set is sent to the peer.
The purpose of this bit is to inform the peer that this endpoint just
is going down, and that the peer should handle the reception of this
particular RESET message as a local failure. This forces the peer to
accept another RESET or ACTIVATE message from this endpoint before it
can re-establish the link. This again is necessary to ensure that
link session numbers are properly exchanged before the link comes up
again.
If a failure is detected locally at the same time at the peer endpoint
this will do the same, which is also a correct behavior.
However, when receiving such messages, the endpoints will not
distinguish between 'stopping' RESETs and ordinary ones when it comes
to updating session numbers. Both endpoints will copy the received
session number and set their 'in_session' flags to true at the
reception, while they are still expecting another RESET from the
peer before they can go ahead and re-establish. This is contradictory,
since, after applying the validation check referred to below, the
'in_session' flag will cause rejection of all such messages, and the
link will never come up again.
We now fix this by not only handling received RESET/STOPPING messages
as a local failure, but also by omitting to set a new session number
and the 'in_session' flag in such cases.
Fixes: 7ea817f4e8 ("tipc: check session number before accepting link protocol messages")
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 63c82997f5 ]
TCA_FLOWER_KEY_ENC_OPTS and TCA_FLOWER_KEY_ENC_OPTS_MASK can only
currently contain further nested attributes, which are parsed by
hand, so the policy is never actually used resulting in a W=1
build warning:
net/sched/cls_flower.c:492:1: warning: ‘enc_opts_policy’ defined but not used [-Wunused-const-variable=]
enc_opts_policy[TCA_FLOWER_KEY_ENC_OPTS_MAX + 1] = {
Add the validation anyway to avoid potential bugs when other
attributes are added and to make the attribute structure slightly
more clear. Validation will also set extact to point to bad
attribute on error.
Fixes: 0a6e77784f ("net/sched: allow flower to match tunnel options")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Simon Horman <simon.horman@netronome.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 19ab69107d ]
tcf_idr_check_alloc() can return a negative value, on allocation failures
(-ENOMEM) or IDR exhaustion (-ENOSPC): don't leak keys_ex in these cases.
Fixes: 0190c1d452 ("net: sched: atomically check-allocate action")
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 7cb6a2a2c7 ]
A timing hazard exists when the network interface is stopped that
allows a watchdog timeout to be processed by a separate core in
parallel. This creates the potential for the timeout handler to
wake the queues while the driver is shutting down, or access
registers after their clocks have been removed.
The more common case is that the watchdog timeout will produce a
warning message which doesn't lead to a crash. The chances of this
are greatly increased by the fact that bcm_sysport_netif_stop stops
the transmit queues which can easily precipitate a watchdog time-
out because of stale trans_start data in the queues.
This commit corrects the behavior by ensuring that the watchdog
timeout is disabled before enterring bcm_sysport_netif_stop. There
are currently only two users of the bcm_sysport_netif_stop function:
close and suspend.
The close case already handles the issue by exiting the RUNNING
state before invoking the driver close service.
The suspend case now performs the netif_device_detach to exit the
PRESENT state before the call to bcm_sysport_netif_stop rather than
after it.
These behaviors prevent any future scheduling of the driver timeout
service during the window. The netif_tx_stop_all_queues function
in bcm_sysport_netif_stop is replaced with netif_tx_disable to ensure
synchronization with any transmit or timeout threads that may
already be executing on other cores.
For symmetry, the netif_device_attach call upon resume is moved to
after the call to bcm_sysport_netif_start. Since it wakes the transmit
queues it is not necessary to invoke netif_tx_start_all_queues from
bcm_sysport_netif_start so it is moved into the driver open service.
Fixes: 40755a0fce ("net: systemport: add suspend and resume support")
Fixes: 80105befdb ("net: systemport: add Broadcom SYSTEMPORT Ethernet MAC driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 8ebebcba55 ]
When writing packets to a descriptor associated with a combined queue, the
packets should end up on that queue.
Before this change all packets written to any descriptor associated with a
tap interface end up on rx-0, even when the descriptor is associated with a
different queue.
The rx traffic can be generated by either of the following.
1. a simple tap program which spins up multiple queues and writes packets
to each of the file descriptors
2. tx from a qemu vm with a tap multiqueue netdev
The queue for rx traffic can be observed by either of the following (done
on the hypervisor in the qemu case).
1. a simple netmap program which opens and reads from per-queue
descriptors
2. configuring RPS and doing per-cpu captures with rxtxcpu
Alternatively, if you printk() the return value of skb_get_rx_queue() just
before each instance of netif_receive_skb() in tun.c, you will get 65535
for every skb.
Calling skb_record_rx_queue() to set the rx queue to the queue_index fixes
the association between descriptor and rx queue.
Signed-off-by: Matthew Cover <matthew.cover@stackpath.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1c1274a569 ]
The code for reading ancillary data from a received buffer is assuming
the buffer is linear. To make this assumption true we have to linearize
the buffer before message data is read.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 59663e4219 ]
This patch has the fix to avoid PHY lockup with 5717/5719/5720 in change
ring and flow control paths. This patch solves the RX hang while doing
continuous ring or flow control parameters with heavy traffic from peer.
Signed-off-by: Siva Reddy Kallam <siva.kallam@broadcom.com>
Acked-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit cadf9df27e ]
During tcp coalescing ensure that the skb hardware timestamp refers to the
highest sequence number data.
Previously only the software timestamp was updated during coalescing.
Signed-off-by: Stephen Mallon <stephen.mallon@sydney.edu.au>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit cc3ccf26f0 ]
As rfc7496#section4.5 says about SCTP_PR_SUPPORTED:
This socket option allows the enabling or disabling of the
negotiation of PR-SCTP support for future associations. For existing
associations, it allows one to query whether or not PR-SCTP support
was negotiated on a particular association.
It means only sctp sock's prsctp_enable can be set.
Note that for the limitation of SCTP_{CURRENT|ALL}_ASSOC, we will
add it when introducing SCTP_{FUTURE|CURRENT|ALL}_ASSOC for linux
sctp in another patchset.
v1->v2:
- drop the params.assoc_id check as Neil suggested.
Fixes: 28aa4c26fc ("sctp: add SCTP_PR_SUPPORTED on sctp sockopt")
Reported-by: Ying Xu <yinxu@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 33d9a2c72f ]
eth_type_trans() assumes initial value for skb->pkt_type
is PACKET_HOST.
This is indeed the value right after a fresh skb allocation.
However, it is possible that GRO merged a packet with a different
value (like PACKET_OTHERHOST in case macvlan is used), so
we need to make sure napi->skb will have pkt_type set back to
PACKET_HOST.
Otherwise, valid packets might be dropped by the stack because
their pkt_type is not PACKET_HOST.
napi_reuse_skb() was added in commit 96e93eab20 ("gro: Add
internal interfaces for VLAN"), but this bug always has
been there.
Fixes: 96e93eab20 ("gro: Add internal interfaces for VLAN")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A timing hazard exists when the network interface is stopped that
allows a watchdog timeout to be processed by a separate core in
parallel. This creates the potential for the timeout handler to
wake the queues while the driver is shutting down, or access
registers after their clocks have been removed.
The more common case is that the watchdog timeout will produce a
warning message which doesn't lead to a crash. The chances of this
are greatly increased by the fact that bcmgenet_netif_stop stops
the transmit queues which can easily precipitate a watchdog time-
out because of stale trans_start data in the queues.
This commit corrects the behavior by ensuring that the watchdog
timeout is disabled before enterring bcmgenet_netif_stop. There
are currently only two users of the bcmgenet_netif_stop function:
close and suspend.
The close case already handles the issue by exiting the RUNNING
state before invoking the driver close service.
The suspend case now performs the netif_device_detach to exit the
PRESENT state before the call to bcmgenet_netif_stop rather than
after it.
These behaviors prevent any future scheduling of the driver timeout
service during the window. The netif_tx_stop_all_queues function
in bcmgenet_netif_stop is replaced with netif_tx_disable to ensure
synchronization with any transmit or timeout threads that may
already be executing on other cores.
For symmetry, the netif_device_attach call upon resume is moved to
after the call to bcmgenet_netif_start. Since it wakes the transmit
queues it is not necessary to invoke netif_tx_start_all_queues from
bcmgenet_netif_start so it is moved into the driver open service.
[ Upstream commit 09e805d257 ]
Fixes: 1c1008c793 ("net: bcmgenet: add main driver file")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 7ddacfa564 ]
Preethi reported that PMTU discovery for UDP/raw applications is not
working in the presence of VRF when the socket is not bound to a device.
The problem is that ip6_sk_update_pmtu does not consider the L3 domain
of the skb device if the socket is not bound. Update the function to
set oif to the L3 master device if relevant.
Fixes: ca254490c8 ("net: Add VRF support to IPv6 stack")
Reported-by: Preethi Ramachandra <preethir@juniper.net>
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 761f60261b ]
These is no need to hold dst before calling rt6_remove_exception_rt().
The call to dst_hold_safe() in ip6_link_failure() was for ip6_del_rt(),
which has been removed in Commit 93531c6743 ("net/ipv6: separate
handling of FIB entries from dst based routes"). Otherwise, it will
cause a dst leak.
This patch is to simply remove the dst_hold_safe() call before calling
rt6_remove_exception_rt() and also do the same in ip6_del_cached_rt().
It's safe, because the removal of the exception that holds its dst's
refcnt is protected by rt6_exception_lock.
Fixes: 93531c6743 ("net/ipv6: separate handling of FIB entries from dst based routes")
Fixes: 23fb93a4d3 ("net/ipv6: Cleanup exception and cache route handling")
Reported-by: Li Shuang <shuali@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 16f7eb2b77 ]
The various types of tunnels running over IPv4 can ask to set the DF
bit to do PMTU discovery. However, PMTU discovery is subject to the
threshold set by the net.ipv4.route.min_pmtu sysctl, and is also
disabled on routes with "mtu lock". In those cases, we shouldn't set
the DF bit.
This patch makes setting the DF bit conditional on the route's MTU
locking state.
This issue seems to be older than git history.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Reviewed-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 62230715fd ]
Only first fragment has the sport/dport information,
not the following ones.
If we want consistent hash for all fragments, we need to
ignore ports even for first fragment.
This bug is visible for IPv6 traffic, if incoming fragments
do not have a flow label, since skb_get_hash() will give
different results for first fragment and following ones.
It is also visible if any routing rule wants dissection
and sport or dport.
See commit 5e5d6fed37 ("ipv6: route: dissect flow
in input path if fib rules need it") for details.
[edumazet] rewrote the changelog completely.
Fixes: 06635a35d1 ("flow_dissect: use programable dissector in skb_flow_dissect and friends")
Signed-off-by: 배석진 <soukjin.bae@samsung.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 44a7276b30 upstream.
In my haste to remove irq_port[] I accidentally changed the
way we deal with hpd pins that are shared by multiple encoders
(DP and HDMI for pre-DDI platforms). Previously we would only
handle such pins via ->hpd_pulse(), but now we queue up the
hotplug work for the HDMI encoder directly. Worse yet, we now
count each hpd twice and this increment the hpd storm count
twice as fast. This can lead to spurious storms being detected.
Go back to the old way of doing things, ie. delegate to
->hpd_pulse() for any pin which has an encoder with that hook
implemented. I don't really like the idea of adding irq_port[]
back so let's loop through the encoders first to check if we
have an encoder with ->hpd_pulse() for the pin, and then go
through all the pins and decided on the correct course of action
based on the earlier findings.
I have occasionally toyed with the idea of unifying the pre-DDI
HDMI and DP encoders into a single encoder as well. Besides the
hotplug processing it would have the other benefit of preventing
userspace from trying to enable both encoders at the same time.
That is simply illegal as they share the same clock/data pins.
We have some testcases that will attempt that and thus fail on
many older machines. But for now let's stick to fixing just the
hotplug code.
Cc: stable@vger.kernel.org # 4.19+
Cc: Lyude Paul <lyude@redhat.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Fixes: b6ca3eee18 ("drm/i915: Nuke dev_priv->irq_port[]")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181108200424.28371-1-ville.syrjala@linux.intel.com
Reviewed-by: Lyude Paul <lyude@redhat.com>
(cherry picked from commit 5a3aeca97a)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fb5bbae9b1 upstream.
Exercising the gpu reloc path strenuously revealed an issue where the
updated relocations (from MI_STORE_DWORD_IMM) were not being observed
upon execution. After some experiments with adding pipecontrols (a lot
of pipecontrols (32) as gen4/5 do not have a bit to wait on earlier pipe
controls or even the current on), it was discovered that we merely
needed to delay the EMIT_INVALIDATE by several flushes. It is important
to note that it is the EMIT_INVALIDATE as opposed to the EMIT_FLUSH that
needs the delay as opposed to what one might first expect -- that the
delay is required for the TLB invalidation to take effect (one presumes
to purge any CS buffers) as opposed to a delay after flushing to ensure
the writes have landed before triggering invalidation.
Testcase: igt/gem_tiled_fence_blits
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@vger.kernel.org
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181105094305.5767-1-chris@chris-wilson.co.uk
(cherry picked from commit 55f99bf2a9)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
