commit 9bb48c82ac upstream.
This makes the tty layer use the .write_iter() function instead of the
traditional .write() functionality.
That allows writev(), but more importantly also makes it possible to
enable .splice_write() for ttys, reinstating the "splice to tty"
functionality that was lost in commit 36e2c7421f ("fs: don't allow
splice read/write without explicit ops").
Fixes: 36e2c7421f ("fs: don't allow splice read/write without explicit ops")
Reported-by: Oliver Giles <ohw.giles@gmail.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cf9d052aa6 upstream.
In Linux, if a driver does disable_irq() and later does enable_irq()
on its interrupt, I believe it's expecting these properties:
* If an interrupt was pending when the driver disabled then it will
still be pending after the driver re-enables.
* If an edge-triggered interrupt comes in while an interrupt is
disabled it should assert when the interrupt is re-enabled.
If you think that the above sounds a lot like the disable_irq() and
enable_irq() are supposed to be masking/unmasking the interrupt
instead of disabling/enabling it then you've made an astute
observation. Specifically when talking about interrupts, "mask"
usually means to stop posting interrupts but keep tracking them and
"disable" means to fully shut off interrupt detection. It's
unfortunate that this is so confusing, but presumably this is all the
way it is for historical reasons.
Perhaps more confusing than the above is that, even though clients of
IRQs themselves don't have a way to request mask/unmask
vs. disable/enable calls, IRQ chips themselves can implement both.
...and yet more confusing is that if an IRQ chip implements
disable/enable then they will be called when a client driver calls
disable_irq() / enable_irq().
It does feel like some of the above could be cleared up. However,
without any other core interrupt changes it should be clear that when
an IRQ chip gets a request to "disable" an IRQ that it has to treat it
like a mask of that IRQ.
In any case, after that long interlude you can see that the "unmask
and clear" can break things. Maulik tried to fix it so that we no
longer did "unmask and clear" in commit 71266d9d39 ("pinctrl: qcom:
Move clearing pending IRQ to .irq_request_resources callback"), but it
only handled the PDC case and it had problems (it caused
sc7180-trogdor devices to fail to suspend). Let's fix.
>From my understanding the source of the phantom interrupt in the
were these two things:
1. One that could have been introduced in msm_gpio_irq_set_type()
(only for the non-PDC case).
2. Edges could have been detected when a GPIO was muxed away.
Fixing case #1 is easy. We can just add a clear in
msm_gpio_irq_set_type().
Fixing case #2 is harder. Let's use a concrete example. In
sc7180-trogdor.dtsi we configure the uart3 to have two pinctrl states,
sleep and default, and mux between the two during runtime PM and
system suspend (see geni_se_resources_{on,off}() for more
details). The difference between the sleep and default state is that
the RX pin is muxed to a GPIO during sleep and muxed to the UART
otherwise.
As per Qualcomm, when we mux the pin over to the UART function the PDC
(or the non-PDC interrupt detection logic) is still watching it /
latching edges. These edges don't cause interrupts because the
current code masks the interrupt unless we're entering suspend.
However, as soon as we enter suspend we unmask the interrupt and it's
counted as a wakeup.
Let's deal with the problem like this:
* When we mux away, we'll mask our interrupt. This isn't necessary in
the above case since the client already masked us, but it's a good
idea in general.
* When we mux back will clear any interrupts and unmask.
Fixes: 4b7618fdc7 ("pinctrl: qcom: Add irq_enable callback for msm gpio")
Fixes: 71266d9d39 ("pinctrl: qcom: Move clearing pending IRQ to .irq_request_resources callback")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Maulik Shah <mkshah@codeaurora.org>
Tested-by: Maulik Shah <mkshah@codeaurora.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20210114191601.v7.4.I7cf3019783720feb57b958c95c2b684940264cd1@changeid
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4079d35fa4 upstream.
When the Qualcomm pinctrl driver wants to Ack an interrupt, it does a
read-modify-write on the interrupt status register. On some SoCs it
makes sure that the status bit is 1 to "Ack" and on others it makes
sure that the bit is 0 to "Ack". Presumably the first type of
interrupt controller is a "write 1 to clear" type register and the
second just let you directly set the interrupt status register.
As far as I can tell from scanning structure definitions, the
interrupt status bit is always in a register by itself. Thus with
both types of interrupt controllers it is safe to "Ack" interrupts
without doing a read-modify-write. We can do a simple write.
It should be noted that if the interrupt status bit _was_ ever in a
register with other things (like maybe status bits for other GPIOs):
a) For "write 1 clear" type controllers then read-modify-write would
be totally wrong because we'd accidentally end up clearing
interrupts we weren't looking at.
b) For "direct set" type controllers then read-modify-write would also
be wrong because someone setting one of the other bits in the
register might accidentally clear (or set) our interrupt.
I say this simply to show that the current read-modify-write doesn't
provide any sort of "future proofing" of the code. In fact (for
"write 1 clear" controllers) the new code is slightly more "future
proof" since it would allow more than one interrupt status bits to
share a register.
NOTE: this code fixes no bugs--it simply avoids an extra register
read.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Maulik Shah <mkshah@codeaurora.org>
Tested-by: Maulik Shah <mkshah@codeaurora.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210114191601.v7.2.I3635de080604e1feda770591c5563bd6e63dd39d@changeid
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 584b7cfcdc upstream.
Multicast entries in the MAC table use the high bits of the MAC
address to encode the ports that should get the packets. But this port
mask does not work for the CPU port, to receive these packets on the
CPU port the MAC_CPU_COPY flag must be set.
Because of this IPv6 was effectively not working because neighbor
solicitations were never received. This was not apparent before commit
9403c158 (net: mscc: ocelot: support IPv4, IPv6 and plain Ethernet mdb
entries) as the IPv6 entries were broken so all incoming IPv6
multicast was then treated as unknown and flooded on all ports.
To fix this problem rework the ocelot_mact_learn() to set the
MAC_CPU_COPY flag when a multicast entry that target the CPU port is
added. For this we have to read back the ports endcoded in the pseudo
MAC address by the caller. It is not a very nice design but that avoid
changing the callers and should make backporting easier.
Signed-off-by: Alban Bedel <alban.bedel@aerq.com>
Fixes: 9403c158b8 ("net: mscc: ocelot: support IPv4, IPv6 and plain Ethernet mdb entries")
Link: https://lore.kernel.org/r/20210119140638.203374-1-alban.bedel@aerq.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9d9b1ee0b2 upstream.
The TCP session does not terminate with TCP_USER_TIMEOUT when data
remain untransmitted due to zero window.
The number of unanswered zero-window probes (tcp_probes_out) is
reset to zero with incoming acks irrespective of the window size,
as described in tcp_probe_timer():
RFC 1122 4.2.2.17 requires the sender to stay open indefinitely
as long as the receiver continues to respond probes. We support
this by default and reset icsk_probes_out with incoming ACKs.
This counter, however, is the wrong one to be used in calculating the
duration that the window remains closed and data remain untransmitted.
Thanks to Jonathan Maxwell <jmaxwell37@gmail.com> for diagnosing the
actual issue.
In this patch a new timestamp is introduced for the socket in order to
track the elapsed time for the zero-window probes that have not been
answered with any non-zero window ack.
Fixes: 9721e709fa ("tcp: simplify window probe aborting on USER_TIMEOUT")
Reported-by: William McCall <william.mccall@gmail.com>
Co-developed-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Enke Chen <enchen@paloaltonetworks.com>
Reviewed-by: Yuchung Cheng <ycheng@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20210115223058.GA39267@localhost.localdomain
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b160c28548 upstream.
Heiner Kallweit reported that some skbs were sent with
the following invalid GSO properties :
- gso_size > 0
- gso_type == 0
This was triggerring a WARN_ON_ONCE() in rtl8169_tso_csum_v2.
Juerg Haefliger was able to reproduce a similar issue using
a lan78xx NIC and a workload mixing TCP incoming traffic
and forwarded packets.
The problem is that tcp_add_backlog() is writing
over gso_segs and gso_size even if the incoming packet will not
be coalesced to the backlog tail packet.
While skb_try_coalesce() would bail out if tail packet is cloned,
this overwriting would lead to corruptions of other packets
cooked by lan78xx, sharing a common super-packet.
The strategy used by lan78xx is to use a big skb, and split
it into all received packets using skb_clone() to avoid copies.
The drawback of this strategy is that all the small skb share a common
struct skb_shared_info.
This patch rewrites TCP gso_size/gso_segs handling to only
happen on the tail skb, since skb_try_coalesce() made sure
it was not cloned.
Fixes: 4f693b55c3 ("tcp: implement coalescing on backlog queue")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Bisected-by: Juerg Haefliger <juergh@canonical.com>
Tested-by: Juerg Haefliger <juergh@canonical.com>
Reported-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=209423
Link: https://lore.kernel.org/r/20210119164900.766957-1-eric.dumazet@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 79267ae226 upstream.
The blamed commit was too aggressive, and it made ocelot_netdevice_event
react only to network interface events emitted for the ocelot switch
ports.
In fact, only the PRECHANGEUPPER should have had that check.
When we ignore all events that are not for us, we miss the fact that the
upper of the LAG changes, and the bonding interface gets enslaved to a
bridge. This is an operation we could offload under certain conditions.
Fixes: 7afb3e575e ("net: mscc: ocelot: don't handle netdev events for other netdevs")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20210118135210.2666246-1-olteanv@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ceed9038b2 upstream.
The multicast route ff00::/8 is created with type RTN_UNICAST:
$ ip -6 -d route
unicast ::1 dev lo proto kernel scope global metric 256 pref medium
unicast fe80::/64 dev eth0 proto kernel scope global metric 256 pref medium
unicast ff00::/8 dev eth0 proto kernel scope global metric 256 pref medium
Set the type to RTN_MULTICAST which is more appropriate.
Fixes: e8478e80e5 ("net/ipv6: Save route type in rt6_info")
Signed-off-by: Matteo Croce <mcroce@microsoft.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a826b04303 upstream.
The ff00::/8 multicast route is created without specifying the fc_protocol
field, so the default RTPROT_BOOT value is used:
$ ip -6 -d route
unicast ::1 dev lo proto kernel scope global metric 256 pref medium
unicast fe80::/64 dev eth0 proto kernel scope global metric 256 pref medium
unicast ff00::/8 dev eth0 proto boot scope global metric 256 pref medium
As the documentation says, this value identifies routes installed during
boot, but the route is created when interface is set up.
Change the value to RTPROT_KERNEL which is a better value.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Matteo Croce <mcroce@microsoft.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8d2b51b008 upstream.
udp_v4_early_demux() is the only function that calls
ip_mc_validate_source() with a TOS that hasn't been masked with
IPTOS_RT_MASK.
This results in different behaviours for incoming multicast UDPv4
packets, depending on if ip_mc_validate_source() is called from the
early-demux path (udp_v4_early_demux) or from the regular input path
(ip_route_input_noref).
ECN would normally not be used with UDP multicast packets, so the
practical consequences should be limited on that side. However,
IPTOS_RT_MASK is used to also masks the TOS' high order bits, to align
with the non-early-demux path behaviour.
Reproducer:
Setup two netns, connected with veth:
$ ip netns add ns0
$ ip netns add ns1
$ ip -netns ns0 link set dev lo up
$ ip -netns ns1 link set dev lo up
$ ip link add name veth01 netns ns0 type veth peer name veth10 netns ns1
$ ip -netns ns0 link set dev veth01 up
$ ip -netns ns1 link set dev veth10 up
$ ip -netns ns0 address add 192.0.2.10 peer 192.0.2.11/32 dev veth01
$ ip -netns ns1 address add 192.0.2.11 peer 192.0.2.10/32 dev veth10
In ns0, add route to multicast address 224.0.2.0/24 using source
address 198.51.100.10:
$ ip -netns ns0 address add 198.51.100.10/32 dev lo
$ ip -netns ns0 route add 224.0.2.0/24 dev veth01 src 198.51.100.10
In ns1, define route to 198.51.100.10, only for packets with TOS 4:
$ ip -netns ns1 route add 198.51.100.10/32 tos 4 dev veth10
Also activate rp_filter in ns1, so that incoming packets not matching
the above route get dropped:
$ ip netns exec ns1 sysctl -wq net.ipv4.conf.veth10.rp_filter=1
Now try to receive packets on 224.0.2.11:
$ ip netns exec ns1 socat UDP-RECVFROM:1111,ip-add-membership=224.0.2.11:veth10,ignoreeof -
In ns0, send packet to 224.0.2.11 with TOS 4 and ECT(0) (that is,
tos 6 for socat):
$ echo test0 | ip netns exec ns0 socat - UDP-DATAGRAM:224.0.2.11:1111,bind=:1111,tos=6
The "test0" message is properly received by socat in ns1, because
early-demux has no cached dst to use, so source address validation
is done by ip_route_input_mc(), which receives a TOS that has the
ECN bits masked.
Now send another packet to 224.0.2.11, still with TOS 4 and ECT(0):
$ echo test1 | ip netns exec ns0 socat - UDP-DATAGRAM:224.0.2.11:1111,bind=:1111,tos=6
The "test1" message isn't received by socat in ns1, because, now,
early-demux has a cached dst to use and calls ip_mc_validate_source()
immediately, without masking the ECN bits.
Fixes: bc044e8db7 ("udp: perform source validation for mcast early demux")
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9c30ae8398 upstream.
The previous commit 32efcc06d2 ("tcp: export count for rehash attempts")
would mis-account rehashing SNMP and socket stats:
a. During handshake of an active open, only counts the first
SYN timeout
b. After handshake of passive and active open, stop updating
after (roughly) TCP_RETRIES1 recurring RTOs
c. After the socket aborts, over count timeout_rehash by 1
This patch fixes this by checking the rehash result from sk_rethink_txhash.
Fixes: 32efcc06d2 ("tcp: export count for rehash attempts")
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Link: https://lore.kernel.org/r/20210119192619.1848270-1-ycheng@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a11a496ee6 upstream.
During testing kasan_populate_early_shadow and kasan_remove_zero_shadow,
if the shadow start and end address in kasan_remove_zero_shadow() is not
aligned to PMD_SIZE, the remain unaligned PTE won't be removed.
In the test case for kasan_remove_zero_shadow():
shadow_start: 0xffffffb802000000, shadow end: 0xffffffbfbe000000
3-level page table:
PUD_SIZE: 0x40000000 PMD_SIZE: 0x200000 PAGE_SIZE: 4K
0xffffffbf80000000 ~ 0xffffffbfbdf80000 will not be removed because in
kasan_remove_pud_table(), kasan_pmd_table(*pud) is true but the next
address is 0xffffffbfbdf80000 which is not aligned to PUD_SIZE.
In the correct condition, this should fallback to the next level
kasan_remove_pmd_table() but the condition flow always continue to skip
the unaligned part.
Fix by correcting the condition when next and addr are neither aligned.
Link: https://lkml.kernel.org/r/20210103135621.83129-1-lecopzer@gmail.com
Fixes: 0207df4fa1 ("kernel/memremap, kasan: make ZONE_DEVICE with work with KASAN")
Signed-off-by: Lecopzer Chen <lecopzer.chen@mediatek.com>
Cc: Andrey Ryabinin <aryabinin@virtuozzo.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Alexander Potapenko <glider@google.com>
Cc: YJ Chiang <yj.chiang@mediatek.com>
Cc: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 66c556025d upstream.
Commit 3226b158e6 ("net: avoid 32 x truesize under-estimation for
tiny skbs") ensured that skbs with data size lower than 1025 bytes
will be kmalloc'ed to avoid excessive page cache fragmentation and
memory consumption.
However, the fix adressed only __napi_alloc_skb() (primarily for
virtio_net and napi_get_frags()), but the issue can still be achieved
through __netdev_alloc_skb(), which is still used by several drivers.
Drivers often allocate a tiny skb for headers and place the rest of
the frame to frags (so-called copybreak).
Mirror the condition to __netdev_alloc_skb() to handle this case too.
Since v1 [0]:
- fix "Fixes:" tag;
- refine commit message (mention copybreak usecase).
[0] https://lore.kernel.org/netdev/20210114235423.232737-1-alobakin@pm.me
Fixes: a1c7fff7e1 ("net: netdev_alloc_skb() use build_skb()")
Signed-off-by: Alexander Lobakin <alobakin@pm.me>
Link: https://lore.kernel.org/r/20210115150354.85967-1-alobakin@pm.me
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9778448175 upstream.
The allocated page is not released if error occurs in
nvm_submit_io_sync_raw(). __free_page() is moved ealier to avoid
possible memory leak issue.
Fixes: aff3fb18f9 ("lightnvm: move bad block and chunk state logic to core")
Signed-off-by: Pan Bian <bianpan2016@163.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fa0732168f upstream.
Properly unwind step by step using refactored helpers from nvme_unmap_data
to avoid a potential double dma_unmap on a mapping failure.
Fixes: 7fe07d14f7 ("nvme-pci: merge nvme_free_iod into nvme_unmap_data")
Reported-by: Marc Orr <marcorr@google.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Marc Orr <marcorr@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9275c206f8 upstream.
Split out three helpers from nvme_unmap_data that will allow finer grained
unwinding from nvme_map_data.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Marc Orr <marcorr@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 87fe04367d upstream.
mv88e6xxx_port_vlan_join checks whether the VTU already contains an
entry for the given vid (via mv88e6xxx_vtu_getnext), and if so, merely
changes the relevant .member[] element and loads the updated entry
into the VTU.
However, at least for the mv88e6250, the on-stack struct
mv88e6xxx_vtu_entry vlan never has its .state[] array explicitly
initialized, neither in mv88e6xxx_port_vlan_join() nor inside the
getnext implementation. So the new entry has random garbage for the
STU bits, breaking VLAN filtering.
When the VTU entry is initially created, those bits are all zero, and
we should make sure to keep them that way when the entry is updated.
Fixes: 92307069a9 (net: dsa: mv88e6xxx: Avoid VTU corruption on 6097)
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Tobias Waldekranz <tobias@waldekranz.com>
Tested-by: Tobias Waldekranz <tobias@waldekranz.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9c25af2502 upstream.
The earlier commit to fix runtime PM in case i915 init fails,
introduces a possibility to hit a page fault.
snd_hdac_ext_bus_device_exit() is designed to be called from
dev.release(). Calling it outside device reference counting, is
not safe and may lead to calling the device_exit() function
twice. Additionally, as part of ext_bus_device_init(), the device
is also registered with snd_hdac_device_register(). Thus before
calling device_exit(), the device must be removed from device
hierarchy first.
Fix the issue by rolling back init actions by calling
hdac_device_unregister() and then releasing device with put_device().
This matches with existing code in hdac-ext module.
To complete the fix, add handling for the case where
hda_codec_load_module() returns -ENODEV, and clean up the hdac_ext
resources also in this case.
In future work, hdac-ext interface should be extended to allow clients
more flexibility to handle the life-cycle of individual devices, beyond
just the current snd_hdac_ext_bus_device_remove(), which removes all
devices.
BugLink: https://github.com/thesofproject/linux/issues/2646
Reported-by: Jaroslav Kysela <perex@perex.cz>
Fixes: 6c63c954e1 ("ASoC: SOF: fix a runtime pm issue in SOF when HDMI codec doesn't work")
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Libin Yang <libin.yang@intel.com>
Reviewed-by: Bard Liao <bard.liao@intel.com>
Link: https://lore.kernel.org/r/20210113150715.3992635-1-kai.vehmanen@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f477a538c1 upstream.
When G2_DMA is enabled and SH_DMA is disabled, it results in the following
Kbuild warning:
WARNING: unmet direct dependencies detected for SH_DMA_API
Depends on [n]: SH_DMA [=n]
Selected by [y]:
- G2_DMA [=y] && SH_DREAMCAST [=y]
The reason is that G2_DMA selects SH_DMA_API without depending on or
selecting SH_DMA while SH_DMA_API depends on SH_DMA.
When G2_DMA was first introduced with commit 40f49e7ed7
("sh: dma: Make G2 DMA configurable."), this wasn't an issue since
SH_DMA_API didn't have such dependency, and this way was the only way to
enable it since SH_DMA_API was non-visible. However, later SH_DMA_API was
made visible and dependent on SH_DMA with commit d8902adcc1
("dmaengine: sh: Add Support SuperH DMA Engine driver").
Let G2_DMA depend on SH_DMA_API instead to avoid Kbuild issues.
Fixes: d8902adcc1 ("dmaengine: sh: Add Support SuperH DMA Engine driver")
Signed-off-by: Necip Fazil Yildiran <fazilyildiran@gmail.com>
Signed-off-by: Rich Felker <dalias@libc.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b3c95d0bdb upstream.
When crtc state need_modeset is true it is not necessary
it is going to be a real modeset, it can turns to be a
fastset instead of modeset.
This turns content protection property to be DESIRED and hdcp
update_pipe left with property to be in DESIRED state but
actual hdcp->value was ENABLED.
This issue is caught with DP MST setup, where we have multiple
connector in same DP_MST topology. When disabling HDCP on one of
DP MST connector leads to set the crtc state need_modeset to true
for all other crtc driving the other DP-MST topology connectors.
This turns up other DP MST connectors CP property to be DESIRED
despite the actual hdcp->value is ENABLED.
Above scenario fails the DP MST HDCP IGT test, disabling HDCP on
one MST stream should not cause to disable HDCP on another MST
stream on same DP MST topology.
v2:
- Fixed connector->base.registration_state == DRM_CONNECTOR_REGISTERED
WARN_ON.
v3:
- Commit log improvement. [Uma]
- Added a comment before scheduling prop_work. [Uma]
Fixes: 33f9a623bf ("drm/i915/hdcp: Update CP as per the kernel internal state")
Cc: Ramalingam C <ramalingam.c@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Ramalingam C <ramalingam.c@intel.com>
Tested-by: Karthik B S <karthik.b.s@intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210111081120.28417-2-anshuman.gupta@intel.com
(cherry picked from commit d276e16702)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1fc7c1ef37 upstream.
Some platforms, such as mips64, don't map __u64 to long long unsigned
int so using %llu produces a warning:
gpio-watch.c: In function ‘main’:
gpio-watch.c:89:30: warning: format ‘%llu’ expects argument of type ‘long long unsigned int’, but argument 4 has type ‘__u64’ {aka ‘long unsigned int’} [-Wformat=]
89 | printf("line %u: %s at %llu\n",
| ~~~^
| |
| long long unsigned int
| %lu
90 | chg.info.offset, event, chg.timestamp_ns);
| ~~~~~~~~~~~~~~~~
| |
| __u64 {aka long unsigned int}
Replace the %llu with PRIu64 and cast the argument to uint64_t.
Fixes: 33f0c47b8f ("tools: gpio: implement gpio-watch")
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2fe7c2f994 upstream.
Some platforms, such as mips64, don't map __u64 to long long unsigned
int so using %llu produces a warning:
gpio-event-mon.c:110:37: warning: format ‘%llu’ expects argument of type ‘long long unsigned int’, but argument 3 has type ‘__u64’ {aka ‘long unsigned int’} [-Wformat=]
110 | fprintf(stdout, "GPIO EVENT at %llu on line %d (%d|%d) ",
| ~~~^
| |
| long long unsigned int
| %lu
111 | event.timestamp_ns, event.offset, event.line_seqno,
| ~~~~~~~~~~~~~~~~~~
| |
| __u64 {aka long unsigned int}
Replace the %llu with PRIu64 and cast the argument to uint64_t.
Fixes: 03fd11b033 ("tools/gpio/gpio-event-mon: fix warning")
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2e5a6266fb upstream.
RT_TOS() only masks one of the two ECN bits. Therefore rpfilter_mt()
treats Not-ECT or ECT(1) packets in a different way than those with
ECT(0) or CE.
Reproducer:
Create two netns, connected with a veth:
$ ip netns add ns0
$ ip netns add ns1
$ ip link add name veth01 netns ns0 type veth peer name veth10 netns ns1
$ ip -netns ns0 link set dev veth01 up
$ ip -netns ns1 link set dev veth10 up
$ ip -netns ns0 address add 192.0.2.10/32 dev veth01
$ ip -netns ns1 address add 192.0.2.11/32 dev veth10
Add a route to ns1 in ns0:
$ ip -netns ns0 route add 192.0.2.11/32 dev veth01
In ns1, only packets with TOS 4 can be routed to ns0:
$ ip -netns ns1 route add 192.0.2.10/32 tos 4 dev veth10
Ping from ns0 to ns1 works regardless of the ECN bits, as long as TOS
is 4:
$ ip netns exec ns0 ping -Q 4 192.0.2.11 # TOS 4, Not-ECT
... 0% packet loss ...
$ ip netns exec ns0 ping -Q 5 192.0.2.11 # TOS 4, ECT(1)
... 0% packet loss ...
$ ip netns exec ns0 ping -Q 6 192.0.2.11 # TOS 4, ECT(0)
... 0% packet loss ...
$ ip netns exec ns0 ping -Q 7 192.0.2.11 # TOS 4, CE
... 0% packet loss ...
Now use iptable's rpfilter module in ns1:
$ ip netns exec ns1 iptables-legacy -t raw -A PREROUTING -m rpfilter --invert -j DROP
Not-ECT and ECT(1) packets still pass:
$ ip netns exec ns0 ping -Q 4 192.0.2.11 # TOS 4, Not-ECT
... 0% packet loss ...
$ ip netns exec ns0 ping -Q 5 192.0.2.11 # TOS 4, ECT(1)
... 0% packet loss ...
But ECT(0) and ECN packets are dropped:
$ ip netns exec ns0 ping -Q 6 192.0.2.11 # TOS 4, ECT(0)
... 100% packet loss ...
$ ip netns exec ns0 ping -Q 7 192.0.2.11 # TOS 4, CE
... 100% packet loss ...
After this patch, rpfilter doesn't drop ECT(0) and CE packets anymore.
Fixes: 8f97339d3f ("netfilter: add ipv4 reverse path filter match")
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0e634efd85 upstream.
Rename intel_dp_sink_dpms() to intel_dp_set_power()
so one doesn't always have to convert from the DPMS
enum values to the actual DP D-states.
Also when dealing with a branch device this has nothing to
do with any sink, so the old name was nonsense anyway.
Also adjust the debug message accordingly, and pimp it
with the standard encoder id+name thing.
Trivial bits done with cocci:
@@
expression DP;
@@
(
- intel_dp_sink_dpms(DP, DRM_MODE_DPMS_OFF)
+ intel_dp_set_power(DP, DP_SET_POWER_D3)
|
- intel_dp_sink_dpms(DP, DRM_MODE_DPMS_ON)
+ intel_dp_set_power(DP, DP_SET_POWER_D0)
)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201016194800.25581-2-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3d1cf435e2 upstream.
If the device passed as the target (second argument) to
device_is_dependent() is not completely registered (that is, it has
been initialized, but not added yet), but the parent pointer of it
is set, it may be missing from the list of the parent's children
and device_for_each_child() called by device_is_dependent() cannot
be relied on to catch that dependency.
For this reason, modify device_is_dependent() to check the ancestors
of the target device by following its parent pointer in addition to
the device_for_each_child() walk.
Fixes: 9ed9895370 ("driver core: Functional dependencies tracking support")
Reported-by: Stephan Gerhold <stephan@gerhold.net>
Tested-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Saravana Kannan <saravanak@google.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Link: https://lore.kernel.org/r/17705994.d592GUb2YH@kreacher
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d0243bbd5d upstream.
There will be memory leak if driver probe failed. Trace as below:
backtrace:
[<000000002415258f>] kmemleak_alloc+0x3c/0x50
[<00000000f447ebe4>] __kmalloc+0x208/0x530
[<0000000048bc7b3a>] of_dma_get_range+0xe4/0x1b0
[<0000000041e39065>] of_dma_configure_id+0x58/0x27c
[<000000006356866a>] platform_dma_configure+0x2c/0x40
......
[<000000000afcf9b5>] ret_from_fork+0x10/0x3c
This issue is introduced by commit e0d072782c73("dma-mapping:
introduce DMA range map, supplanting dma_pfn_offset "). It doesn't
free dma_range_map when driver probe failed and cause above
memory leak. So, add code to free it in error path.
Fixes: e0d072782c ("dma-mapping: introduce DMA range map, supplanting dma_pfn_offset ")
Cc: stable@vger.kernel.org
Signed-off-by: Meng Li <Meng.Li@windriver.com>
Link: https://lore.kernel.org/r/20210105070927.14968-1-Meng.Li@windriver.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit da7e0c3c29 upstream.
Occasionally, we are seeing some SuperSpeed devices resumes right after
being directed to U3. This commits add 500us delay to ensure LFPS
detector is disabled before sending ACK to firmware.
[ 16.099363] tegra-xusb 70090000.usb: entering ELPG
[ 16.104343] tegra-xusb 70090000.usb: 2-1 isn't suspended: 0x0c001203
[ 16.114576] tegra-xusb 70090000.usb: not all ports suspended: -16
[ 16.120789] tegra-xusb 70090000.usb: entering ELPG failed
The register write passes through a few flop stages of 32KHz clock domain.
NVIDIA ASIC designer reviewed RTL and suggests 500us delay.
Cc: stable@vger.kernel.org
Signed-off-by: JC Kuo <jckuo@nvidia.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210115161907.2875631-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
