These printing macros already add a trailing newline, so drop these
unnecessary additional newlines.
Signed-off-by: Alex Lu <alex_lu@realsil.com.cn>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Change-Id: I54df8f119c1927971e4382eaa381981264b68f6a
the rtl: or RTL: prefix in the string is pointless. The rtl_dev_* macros
already does that.
Signed-off-by: Alex Lu <alex_lu@realsil.com.cn>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Change-Id: I4d9b975b0f914f08bf556282a3a0140b71225283
This patch is used to print fw version for debug convenience
Signed-off-by: Alex Lu <alex_lu@realsil.com.cn>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Change-Id: I47c36597134eb6e1cea3f984951de2e76b52a267
Realtek Bluetooth controllers can do both LE scan and BR/EDR inquiry
at once, need to set HCI_QUIRK_SIMULTANEOUS_DISCOVERY quirk.
Signed-off-by: Alex Lu <alex_lu@realsil.com.cn>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Change-Id: If809ec66e8aebe7ba8e675606f5d6202b981f54e
This device is functionally equivalent to the BT part of the RTL8723DE,
uses the same firmware, but the LMP subversion and HCI revision are unique.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Change-Id: I2c4d3cedb5216064d8edc05eb77f240256da3228
Realtek RTL8822BE BT chip on ASUS X420FA cannot be turned on correctly
after on-off several times. Bluetooth daemon sets BT mode failed when
this issue happens. Scanning must be active while turning off for this
bug to be hit.
bluetoothd[1576]: Failed to set mode: Failed (0x03)
If BT is turned off, then turned on again, it works correctly again.
According to the vendor driver, the HCI_QUIRK_RESET_ON_CLOSE flag is set
during probing. So, this patch makes Realtek's BT reset on close to fix
this issue.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=203429
Signed-off-by: Jian-Hong Pan <jian-hong@endlessm.com>
Reviewed-by: Daniel Drake <drake@endlessm.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Change-Id: I764d6c28e43fcbc7eb1a8f3586633be7920155b8
Realtek bluetooth may not work after reboot:
[ 12.446130] Bluetooth: hci0: RTL: rtl: unknown IC info, lmp subver a99e, hci rev 826c, hci ver 0008
This is a regression introduced by commit 26503ad25d ("Bluetooth:
btrtl: split the device initialization into smaller parts"). The new
logic errors out early when no matching IC info can be found, in this
case it means the firmware is already loaded.
So let's assume the firmware is already loaded when we can't find
matching IC info, like the old logic did.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=201921
Fixes: 26503ad25d ("Bluetooth: btrtl: split the device initialization into smaller parts")
Cc: stable@vger.kernel.org # 4.19+
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Change-Id: Iaecc33c211041dff616fac485ef9af4e80263b38
This device is included in the RTL8822CU combination wifi and BT part,
as well as the BT part of the RTL8822CE.
The necessary firmware has been submitted to the linux-firmware
project.
Signed-off-by: Alex Lu <alex_lu@realsil.com.cn>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Change-Id: Ic42028110646bb55c604d3e6042a43b34ccf5501
Don't populate the array extension_sig on the stack but instead make it
static. Makes the object code smaller by 75 bytes:
Before:
text data bss dec hex filename
14325 4920 0 19245 4b2d drivers/bluetooth/btrtl.o
After:
text data bss dec hex filename
14186 4984 0 19170 4ae2 drivers/bluetooth/btrtl.o
(gcc version 8.2.0 x86_64)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Change-Id: I4f8c2f2e1fc242110a322fe9618dce95f7280711
The contents of the rtl_bt/rtlXXXX_config.bin file may be board specific
allow the caller of btrtl_initialize to specify a postfix identifying
the board, which if specified will make btrtl_initialize look for
rtl_bt/rtlXXXX_config-<postfix>.bin instead.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Change-Id: I841a33115606d66f539266ff8b3be3ab24f3c744
The Realtek RTL8723BS and RTL8723DS chipsets are SDIO wifi chips. They
also contain a Bluetooth module which is connected via UART to the host.
Realtek's userspace initialization tool (rtk_hciattach) differentiates
these two via the HCI version and revision returned by the
HCI_OP_READ_LOCAL_VERSION command.
Additionally we apply these checks only the for UART devices. Everything
else is assumed to be a "RTL8723B" which was originally supported by the
driver (communicating via USB).
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jeremy Cline <jeremy@jcline.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Change-Id: I80200b7f62924e91a8e757418f6ccfde81877565
The UART settings are embedded in the config blob. This has to be parsed
to successfully initialize the Bluetooth part of the RTL8723BS (which is
an SDIO chip, but the Bluetooth part is connected via UART).
The Realtek "rtl8723bs_bt" and "rtl8723ds_bt" userspace Bluetooth UART
initialization tools (rtk_hciattach) use the following sequence:
- send H5 sync pattern (already supported by hci_h5)
- get LMP version (already supported by btrtl)
- get ROM version (already supported by btrtl)
- load the firmware and config for the current chipset (already
supported by btrtl)
- read UART settings from the config blob (part of this patch)
- send UART settings via a vendor command to the device (which changes
the baudrate of the device and enables or disables flow control
depending on the config)
- change the baudrate and flow control settings on the host
- send the firmware and config blob to the device (already supported by
btrtl)
Sending the last firmware and config blob download command
(rtl_download_cmd) fails if the UART settings are not updated
beforehand. This is presumably because the device applies the config
right after the firmware and config blob download - which means that at
this point the host is using different UART settings than the device
(which will obviously result in non-working communication).
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jeremy Cline <jeremy@jcline.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Change-Id: I95b475b88aca0d4aa62a7bf482479236d803890c
Consistently use rtl_dev_err and rtl_dev_info everywhere for messages.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Change-Id: I4a41cf52f92b11a33b60834324efcdceb74c48b2
This prepares the btrtl code so it can be used to initialize Bluetooth
modules connected via UART (these are found for example on the RTL8723BS
and RTL8723DS SDIO chips, which come with an embedded UART Bluetooth
module).
The Realtek "rtl8723bs_bt" and "rtl8723ds_bt" userspace Bluetooth UART
initialization tools (rtk_hciattach) use the following sequence:
1) send H5 sync pattern (already supported by hci_h5)
2) get LMP version (already supported by btrtl)
3) get ROM version (already supported by btrtl)
4) load the firmware and config for the current chipset (already
supported by btrtl)
5) read UART settings from the config blob (currently not supported)
6) send UART settings via a vendor command to the device (which changes
the baudrate of the device and enables or disables flow control
depending on the config)
7) change the baudrate and flow control settings on the host
8) send the firmware and config blob to the device (already supported by
btrtl)
The main reason why the initialization has to be split is step #7. This
requires changes to the underlying "bus", which should be kept outside
of the "generic" btrtl driver.
The idea for this split is borrowed from the btbcm driver but adjusted
where needed (the btrtl driver for example needs two blobs: firmware and
config, while the btbcm only needs one).
This also prepares the code for step #5 (parsing the config blob) by
centralizing the code which loads the firmware and config blobs and
storing the result in the new struct btrtl_device_info.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jeremy Cline <jeremy@jcline.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Change-Id: Icc40dd820b448be0a4b3933777e02d09b9d38acf
The Bluetooth parts of RTL8723D and RTL8723B share the same lmp
subversion, thus we need to check both lmp subversion and hci revision
to distinguish the two. The same situation is true for RTL8821A and
RTL8821C. Accordingly, the selection code is revised.
To improve maintainability, a new id_table struct is defined, and an
array of such structs is constructed. Adding a new device can thus be
as simple as adding another value to the table.
Signed-off-by: Alex Lu <alex_lu@realsil.com.cn>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Change-Id: Ic98eb91ac87a671d7fc3d2a611545e36c3c8cf69
In case of using BT_ERR and BT_INFO, convert to bt_dev_err and
bt_dev_info when possible. This allows for controller specific
reporting.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Change-Id: I3cd472bf3ce8e797b112c36227884ee2d80b6394
We accidentally return success if the kmemdup() fails. It results in
a NULL dereference in the caller.
Fixes: 1110a2dbe6 ("Bluetooth: btrtl: Add RTL8822BE Bluetooth device")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Change-Id: Idd4ff62726885f4aafb3aae69c7cddb12c08442b
The message concerning missing config files for 8723b, 8821a, and
8761a should have been issued with BT_INFO() rather than BT_ERR() as
this condition is not fatal. After looking at that code, I have
reworked the logic to log such messages only if the device needs such a
config file. At the moment, only the 8822b fits that description.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Acked-by: 陆朱伟 <alex_lu@realsil.com.cn>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Change-Id: I8449be0c4487c8e7af034753cddcc795205ff503
The existing force64b routine might not work properly under specific
conditions. This patch fixes that bug of 64 bits per word and forces
use that option. It will improve SPI performance significantly.
Signed-off-by: Deokgyu Yang <secugyu@gmail.com>
Change-Id: I85a58d425303ea1765b7b83ee5dd5f0a7f4203fc
In case of 2560x1600@60hz, unstable display operation may occur
with some specific monitors those pixel clock is under 300MHz.
So, default timing for 2560x1600p60hz is set as following.
Detailed mode: Clock 268.500 MHz, 641 mm x 401 mm
2560 2608 2640 2720 ( 48 32 80)
1600 1602 1608 1646 ( 2 6 38)
+hsync -vsync
VertFreq: 59.972 Hz, HorFreq: 98.713 kHz
Change-Id: Iec9df8713211cf5e0dc7ba09f3dba2948e479b4f
