commit 06781a5026 upstream.
The DEVICE_BUSY_TIMEOUT value is described in the Reference Manual as:
| Timeout waiting for NAND Ready/Busy or ATA IRQ. Used in WAIT_FOR_READY
| mode. This value is the number of GPMI_CLK cycles multiplied by 4096.
So instead of multiplying the value in cycles with 4096, we have to
divide it by that value. Use DIV_ROUND_UP to make sure we are on the
safe side, especially when the calculated value in cycles is smaller
than 4096 as typically the case.
This bug likely never triggered because any timeout != 0 usually will
do. In my case the busy timeout in cycles was originally calculated as
2408, which multiplied with 4096 is 0x968000. The lower 16 bits were
taken for the 16 bit wide register field, so the register value was
0x8000. With 2970bf5a32 ("mtd: rawnand: gpmi: fix controller timings
setting") however the value in cycles became 2384, which multiplied
with 4096 is 0x950000. The lower 16 bit are 0x0 now resulting in an
intermediate timeout when reading from NAND.
Fixes: b120612206 ("mtd: rawnand: gpmi: use core timings instead of an empirical derivation")
Cc: stable@vger.kernel.org
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220614083138.3455683-1-s.hauer@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 12378a5a75 upstream.
When a packet enters the OVS datapath and does not match any existing
flows installed in the kernel flow cache, the packet will be sent to
userspace to be parsed, and a new flow will be created. The kernel and
OVS rely on each other to parse packet fields in the same way so that
packets will be handled properly.
As per the design document linked below, OVS expects all later IPv6
fragments to have nw_proto=44 in the flow key, so they can be correctly
matched on OpenFlow rules. OpenFlow controllers create pipelines based
on this design.
This behavior was changed by the commit in the Fixes tag so that
nw_proto equals the next_header field of the last extension header.
However, there is no counterpart for this change in OVS userspace,
meaning that this field is parsed differently between OVS and the
kernel. This is a problem because OVS creates actions based on what is
parsed in userspace, but the kernel-provided flow key is used as a match
criteria, as described in Documentation/networking/openvswitch.rst. This
leads to issues such as packets incorrectly matching on a flow and thus
the wrong list of actions being applied to the packet. Such changes in
packet parsing cannot be implemented without breaking the userspace.
The offending commit is partially reverted to restore the expected
behavior.
The change technically made sense and there is a good reason that it was
implemented, but it does not comply with the original design of OVS.
If in the future someone wants to implement such a change, then it must
be user-configurable and disabled by default to preserve backwards
compatibility with existing OVS versions.
Cc: stable@vger.kernel.org
Fixes: fa642f0883 ("openvswitch: Derive IP protocol number for IPv6 later frags")
Link: https://docs.openvswitch.org/en/latest/topics/design/#fragments
Signed-off-by: Rosemarie O'Riorden <roriorden@redhat.com>
Acked-by: Eelco Chaudron <echaudro@redhat.com>
Link: https://lore.kernel.org/r/20220621204845.9721-1-roriorden@redhat.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5faa0bc691 upstream.
Currently the Conexant codec driver sets up the beep NID after calling
snd_hda_gen_parse_auto_config(). It turned out that this results in
the insufficient setup for the beep control, as the generic parser
handles the fake path in snd_hda_gen_parse_auto_config() only if the
beep_nid is set up beforehand.
For dealing with the beep widget properly, call cx_auto_parse_beep()
before snd_hda_gen_parse_auto_config() call.
Fixes: 51e19ca5f7 ("ALSA: hda/conexant - Clean up beep code")
Cc: <stable@vger.kernel.org>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=216152
Link: https://lore.kernel.org/r/20220620104008.1994-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 534d2eaf19 upstream.
It used to be that mix_interrupt_randomness() would credit 1 bit each
time it ran, and so add_interrupt_randomness() would schedule mix() to
run every 64 interrupts, a fairly arbitrary number, but nonetheless
considered to be a decent enough conservative estimate.
Since e3e33fc2ea ("random: do not use input pool from hard IRQs"),
mix() is now able to credit multiple bits, depending on the number of
calls to add(). This was done for reasons separate from this commit, but
it has the nice side effect of enabling this patch to schedule mix()
less often.
Currently the rules are:
a) Credit 1 bit for every 64 calls to add().
b) Schedule mix() once a second that add() is called.
c) Schedule mix() once every 64 calls to add().
Rules (a) and (c) no longer need to be coupled. It's still important to
have _some_ value in (c), so that we don't "over-saturate" the fast
pool, but the once per second we get from rule (b) is a plenty enough
baseline. So, by increasing the 64 in rule (c) to something larger, we
avoid calling queue_work_on() as frequently during irq storms.
This commit changes that 64 in rule (c) to be 1024, which means we
schedule mix() 16 times less often. And it does *not* need to change the
64 in rule (a).
Fixes: 58340f8e95 ("random: defer fast pool mixing to worker")
Cc: stable@vger.kernel.org
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ff2047fb75 upstream.
Drop support for these ioctls:
* PIO_FONT, PIO_FONTX
* GIO_FONT, GIO_FONTX
* PIO_FONTRESET
As was demonstrated by commit 90bfdeef83 (tty: make FONTX ioctl use
the tty pointer they were actually passed), these ioctls are not used
from userspace, as:
1) they used to be broken (set up font on current console, not the open
one) and racy (before the commit above)
2) KDFONTOP ioctl is used for years instead
Note that PIO_FONTRESET is defunct on most systems as VGA_CONSOLE is set
on them for ages. That turns on BROKEN_GRAPHICS_PROGRAMS which makes
PIO_FONTRESET just return an error.
We are removing KD_FONT_FLAG_OLD here as it was used only by these
removed ioctls. kd.h header exists both in kernel and uapi headers, so
we can remove the kernel one completely. Everyone includeing kd.h will
now automatically get the uapi one.
There are now unused definitions of the ioctl numbers and "struct
consolefontdesc" in kd.h, but as it is a uapi header, I am not touching
these.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210105120239.28031-8-jslaby@suse.cz
Cc: guodaxing <guodaxing@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c50f11c619 upstream.
Invalidating the buffer memory in arch_sync_dma_for_device() for
FROM_DEVICE transfers
When using the streaming DMA API to map a buffer prior to inbound
non-coherent DMA (i.e. DMA_FROM_DEVICE), we invalidate any dirty CPU
cachelines so that they will not be written back during the transfer and
corrupt the buffer contents written by the DMA. This, however, poses two
potential problems:
(1) If the DMA transfer does not write to every byte in the buffer,
then the unwritten bytes will contain stale data once the transfer
has completed.
(2) If the buffer has a virtual alias in userspace, then stale data
may be visible via this alias during the period between performing
the cache invalidation and the DMA writes landing in memory.
Address both of these issues by cleaning (aka writing-back) the dirty
lines in arch_sync_dma_for_device(DMA_FROM_DEVICE) instead of discarding
them using invalidation.
Cc: Ard Biesheuvel <ardb@kernel.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Robin Murphy <robin.murphy@arm.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20220606152150.GA31568@willie-the-truck
Signed-off-by: Will Deacon <will@kernel.org>
Reviewed-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://lore.kernel.org/r/20220610151228.4562-2-will@kernel.org
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e8161345dd upstream.
In commit 190cc82489 ("tcp: change source port randomizarion at
connect() time"), the table_perturb[] array was introduced and an
index was taken from the port_offset via hash_32(). But it turns
out that hash_32() performs a multiplication while the input here
comes from the output of SipHash in secure_seq, that is well
distributed enough to avoid the need for yet another hash.
Suggested-by: Amit Klein <aksecurity@gmail.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Cc: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4c2c8f03a5 upstream.
Moshe Kol, Amit Klein, and Yossi Gilad reported being able to accurately
identify a client by forcing it to emit only 40 times more connections
than there are entries in the table_perturb[] table. The previous two
improvements consisting in resalting the secret every 10s and adding
randomness to each port selection only slightly improved the situation,
and the current value of 2^8 was too small as it's not very difficult
to make a client emit 10k connections in less than 10 seconds.
Thus we're increasing the perturb table from 2^8 to 2^16 so that the
same precision now requires 2.6M connections, which is more difficult in
this time frame and harder to hide as a background activity. The impact
is that the table now uses 256 kB instead of 1 kB, which could mostly
affect devices making frequent outgoing connections. However such
components usually target a small set of destinations (load balancers,
database clients, perf assessment tools), and in practice only a few
entries will be visited, like before.
A live test at 1 million connections per second showed no performance
difference from the previous value.
Reported-by: Moshe Kol <moshe.kol@mail.huji.ac.il>
Reported-by: Yossi Gilad <yossi.gilad@mail.huji.ac.il>
Reported-by: Amit Klein <aksecurity@gmail.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Cc: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ca7af04025 upstream.
Here we're randomly adding between 0 and 7 random increments to the
selected source port in order to add some noise in the source port
selection that will make the next port less predictable.
With the default port range of 32768-60999 this means a worst case
reuse scenario of 14116/8=1764 connections between two consecutive
uses of the same port, with an average of 14116/4.5=3137. This code
was stressed at more than 800000 connections per second to a fixed
target with all connections closed by the client using RSTs (worst
condition) and only 2 connections failed among 13 billion, despite
the hash being reseeded every 10 seconds, indicating a perfectly
safe situation.
Cc: Moshe Kol <moshe.kol@mail.huji.ac.il>
Cc: Yossi Gilad <yossi.gilad@mail.huji.ac.il>
Cc: Amit Klein <aksecurity@gmail.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Cc: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c579bd1b40 upstream.
Even when implementing RFC 6056 3.3.4 (Algorithm 4: Double-Hash
Port Selection Algorithm), a patient attacker could still be able
to collect enough state from an otherwise idle host.
Idea of this patch is to inject some noise, in the
cases __inet_hash_connect() found a candidate in the first
attempt.
This noise should not significantly reduce the collision
avoidance, and should be zero if connection table
is already well used.
Note that this is not implementing RFC 6056 3.3.5
because we think Algorithm 5 could hurt typical
workloads.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: David Dworken <ddworken@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cc: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b337af3a4d upstream.
In systemd systems setting a fixed MAC address through
the "dev_addr" module argument fails systematically.
When checking the MAC address after the interface is created
it always has the same but different MAC address to the one
supplied as argument.
This is partially caused by systemd which by default will
set an internally generated permanent MAC address for interfaces
that are marked as having a randomly generated address.
Commit 890d5b4090 ("usb: gadget: u_ether: fix race in
setting MAC address in setup phase") didn't take into account
the fact that the interface must be marked as having a set
MAC address when it's set as module argument.
Fixed by marking the interface with NET_ADDR_SET when
the "dev_addr" module argument is supplied.
Fixes: 890d5b4090 ("usb: gadget: u_ether: fix race in setting MAC address in setup phase")
Cc: stable@vger.kernel.org
Signed-off-by: Marian Postevca <posteuca@mutex.one>
Link: https://lore.kernel.org/r/20220603153459.32722-1-posteuca@mutex.one
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 9c37de297f upstream.
There is no benefit to DM special-casing NVMe. Remove all code used to
establish DM_TYPE_NVME_BIO_BASED.
Also, remove 3 'struct mapped_device *md' variables in __map_bio() which
masked the same variable that is available within __map_bio()'s scope.
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Mike Snitzer <snitzer@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fc585d4a5c upstream.
The existing __lshrti3 was really inefficient, and the other two helpers
are also needed to compile some modules.
Add the missing versions, and export all of the symbols like arm64
already does.
This code is based on the assembly generated by libgcc builds.
This fixes a build break triggered by ubsan:
riscv64-unknown-linux-gnu-ld: lib/ubsan.o: in function `.L2':
ubsan.c:(.text.unlikely+0x38): undefined reference to `__ashlti3'
riscv64-unknown-linux-gnu-ld: ubsan.c:(.text.unlikely+0x42): undefined reference to `__ashrti3'
Signed-off-by: Olof Johansson <olof@lixom.net>
[paul.walmsley@sifive.com: use SYM_FUNC_{START,END} instead of
ENTRY/ENDPROC; note libgcc origin]
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 30aca1bacb upstream.
riscv's <vdso/processor.h> uses barrier() so it should include
<asm/barrier.h>
Fixes this build error:
CC [M] drivers/net/ethernet/emulex/benet/be_main.o
In file included from ./include/vdso/processor.h:10,
from ./arch/riscv/include/asm/processor.h:11,
from ./include/linux/prefetch.h:15,
from drivers/net/ethernet/emulex/benet/be_main.c:14:
./arch/riscv/include/asm/vdso/processor.h: In function 'cpu_relax':
./arch/riscv/include/asm/vdso/processor.h:14:2: error: implicit declaration of function 'barrier' [-Werror=implicit-function-declaration]
14 | barrier();
This happens with a total of 5 networking drivers -- they all use
<linux/prefetch.h>.
rv64 allmodconfig now builds cleanly after this patch.
Fixes fallout from:
815f0ddb34 ("include/linux/compiler*.h: make compiler-*.h mutually exclusive")
Fixes: ad5d1122b8 ("riscv: use vDSO common flow to reduce the latency of the time-related functions")
Reported-by: Andreas Schwab <schwab@linux-m68k.org>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Arvind Sankar <nivedita@alum.mit.edu>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
[sudip: change in old path]
Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7ee31a3aa8 upstream.
Commit 36dadef23f ("kprobes: Init kprobes in early_initcall") enabled
using kprobes from early_initcall. Unfortunately at this point the
hardware debug infrastructure is not operational. The OS lock may still
be locked, and the hardware watchpoints may have unknown values when
kprobe enables debug monitors to single-step instructions.
Rather than using hardware single-step, append a BRK instruction after
the instruction to be executed out-of-line.
Fixes: 36dadef23f ("kprobes: Init kprobes in early_initcall")
Suggested-by: Will Deacon <will@kernel.org>
Signed-off-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Acked-by: Masami Hiramatsu <mhiramat@kernel.org>
Link: https://lore.kernel.org/r/20201103134900.337243-1-jean-philippe@linaro.org
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Mark-PK Tsai <mark-pk.tsai@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1f30fb9166 upstream.
While parsing user-provided actions, openvswitch module may dynamically
allocate memory and store pointers in the internal copy of the actions.
So this memory has to be freed while destroying the actions.
Currently there are only two such actions: ct() and set(). However,
there are many actions that can hold nested lists of actions and
ovs_nla_free_flow_actions() just jumps over them leaking the memory.
For example, removal of the flow with the following actions will lead
to a leak of the memory allocated by nf_ct_tmpl_alloc():
actions:clone(ct(commit),0)
Non-freed set() action may also leak the 'dst' structure for the
tunnel info including device references.
Under certain conditions with a high rate of flow rotation that may
cause significant memory leak problem (2MB per second in reporter's
case). The problem is also hard to mitigate, because the user doesn't
have direct control over the datapath flows generated by OVS.
Fix that by iterating over all the nested actions and freeing
everything that needs to be freed recursively.
New build time assertion should protect us from this problem if new
actions will be added in the future.
Unfortunately, openvswitch module doesn't use NLA_F_NESTED, so all
attributes has to be explicitly checked. sample() and clone() actions
are mixing extra attributes into the user-provided action list. That
prevents some code generalization too.
Fixes: 34ae932a40 ("openvswitch: Make tunnel set action attach a metadata dst")
Link: https://mail.openvswitch.org/pipermail/ovs-dev/2022-March/392922.html
Reported-by: Stéphane Graber <stgraber@ubuntu.com>
Signed-off-by: Ilya Maximets <i.maximets@ovn.org>
Acked-by: Aaron Conole <aconole@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
[Backport for 5.4: Removed handling of OVS_ACTION_ATTR_DEC_TTL as it
doesn't exist in this version. BUILD_BUG_ON condition adjusted
accordingly.]
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2061ecfdf2 upstream.
If packet headers changed, the cached nfct is no longer relevant
for the packet and attempt to re-use it leads to the incorrect packet
classification.
This issue is causing broken connectivity in OpenStack deployments
with OVS/OVN due to hairpin traffic being unexpectedly dropped.
The setup has datapath flows with several conntrack actions and tuple
changes between them:
actions:ct(commit,zone=8,mark=0/0x1,nat(src)),
set(eth(src=00:00:00:00:00:01,dst=00:00:00:00:00:06)),
set(ipv4(src=172.18.2.10,dst=192.168.100.6,ttl=62)),
ct(zone=8),recirc(0x4)
After the first ct() action the packet headers are almost fully
re-written. The next ct() tries to re-use the existing nfct entry
and marks the packet as invalid, so it gets dropped later in the
pipeline.
Clearing the cached conntrack entry whenever packet tuple is changed
to avoid the issue.
The flow key should not be cleared though, because we should still
be able to match on the ct_state if the recirculation happens after
the tuple change but before the next ct() action.
Cc: stable@vger.kernel.org
Fixes: 7f8a436eaa ("openvswitch: Add conntrack action")
Reported-by: Frode Nordahl <frode.nordahl@canonical.com>
Link: https://mail.openvswitch.org/pipermail/ovs-discuss/2022-May/051829.html
Link: https://bugs.launchpad.net/ubuntu/+source/ovn/+bug/1967856
Signed-off-by: Ilya Maximets <i.maximets@ovn.org>
Link: https://lore.kernel.org/r/20220606221140.488984-1-i.maximets@ovn.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
[Backport to 5.10: minor rebase in ovs_ct_clear function.
This version also applicable to and tested on 5.4 and 4.19.]
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4ddc844eb8 upstream.
in current Linux, MTU policing does not take into account that packets at
the TC ingress have the L2 header pulled. Thus, the same TC police action
(with the same value of tcfp_mtu) behaves differently for ingress/egress.
In addition, the full GSO size is compared to tcfp_mtu: as a consequence,
the policer drops GSO packets even when individual segments have the L2 +
L3 + L4 + payload length below the configured valued of tcfp_mtu.
Improve the accuracy of MTU policing as follows:
- account for mac_len for non-GSO packets at TC ingress.
- compare MTU threshold with the segmented size for GSO packets.
Also, add a kselftest that verifies the correct behavior.
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Reviewed-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
[dcaratti: fix conflicts due to lack of the following commits:
- commit 2ffe039528 ("net/sched: act_police: add support for
packet-per-second policing")
- commit afe231d32e ("selftests: forwarding: Add tc-police tests")
- commit 53b61f2936 ("selftests: forwarding: Add tc-police tests for
packets per second")]
Link: https://lore.kernel.org/netdev/876d597a0ff55f6ba786f73c5a9fd9eb8d597a03.1644514748.git.dcaratti@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7e415282b4 upstream.
GCC 12 enhanced -Waddress when comparing array address to null [0],
which warns:
drivers/virtio/virtio_pci_common.c: In function ‘vp_del_vqs’:
drivers/virtio/virtio_pci_common.c:257:29: warning: the comparison will always evaluate as ‘true’ for the pointer operand in ‘vp_dev->msix_affinity_masks + (sizetype)((long unsigned int)i * 256)’ must not be NULL [-Waddress]
257 | if (vp_dev->msix_affinity_masks[i])
| ^~~~~~
In fact, the verification is comparing the result of a pointer
arithmetic, the address "msix_affinity_masks + i", which will always
evaluate to true.
Under the hood, free_cpumask_var() calls kfree(), which is safe to pass
NULL, not requiring non-null verification. So remove the verification
to make compiler happy (happy compiler, happy life).
[0] https://gcc.gnu.org/bugzilla/show_bug.cgi?id=102103
Signed-off-by: Murilo Opsfelder Araujo <muriloo@linux.ibm.com>
Message-Id: <20220415023002.49805-1-muriloo@linux.ibm.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Christophe de Dinechin <dinechin@redhat.com>
Cc: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b55c3cd102 upstream.
We capture a NULL pointer issue when resizing a corrupt ext4 image which
is freshly clear resize_inode feature (not run e2fsck). It could be
simply reproduced by following steps. The problem is because of the
resize_inode feature was cleared, and it will convert the filesystem to
meta_bg mode in ext4_resize_fs(), but the es->s_reserved_gdt_blocks was
not reduced to zero, so could we mistakenly call reserve_backup_gdb()
and passing an uninitialized resize_inode to it when adding new group
descriptors.
mkfs.ext4 /dev/sda 3G
tune2fs -O ^resize_inode /dev/sda #forget to run requested e2fsck
mount /dev/sda /mnt
resize2fs /dev/sda 8G
========
BUG: kernel NULL pointer dereference, address: 0000000000000028
CPU: 19 PID: 3243 Comm: resize2fs Not tainted 5.18.0-rc7-00001-gfde086c5ebfd #748
...
RIP: 0010:ext4_flex_group_add+0xe08/0x2570
...
Call Trace:
<TASK>
ext4_resize_fs+0xbec/0x1660
__ext4_ioctl+0x1749/0x24e0
ext4_ioctl+0x12/0x20
__x64_sys_ioctl+0xa6/0x110
do_syscall_64+0x3b/0x90
entry_SYSCALL_64_after_hwframe+0x44/0xae
RIP: 0033:0x7f2dd739617b
========
The fix is simple, add a check in ext4_resize_begin() to make sure that
the es->s_reserved_gdt_blocks is zero when the resize_inode feature is
disabled.
Cc: stable@kernel.org
Signed-off-by: Zhang Yi <yi.zhang@huawei.com>
Reviewed-by: Ritesh Harjani <ritesh.list@gmail.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Link: https://lore.kernel.org/r/20220601092717.763694-1-yi.zhang@huawei.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a08f789d2a upstream.
Hulk Robot reported a BUG_ON:
==================================================================
kernel BUG at fs/ext4/mballoc.c:3211!
[...]
RIP: 0010:ext4_mb_mark_diskspace_used.cold+0x85/0x136f
[...]
Call Trace:
ext4_mb_new_blocks+0x9df/0x5d30
ext4_ext_map_blocks+0x1803/0x4d80
ext4_map_blocks+0x3a4/0x1a10
ext4_writepages+0x126d/0x2c30
do_writepages+0x7f/0x1b0
__filemap_fdatawrite_range+0x285/0x3b0
file_write_and_wait_range+0xb1/0x140
ext4_sync_file+0x1aa/0xca0
vfs_fsync_range+0xfb/0x260
do_fsync+0x48/0xa0
[...]
==================================================================
Above issue may happen as follows:
-------------------------------------
do_fsync
vfs_fsync_range
ext4_sync_file
file_write_and_wait_range
__filemap_fdatawrite_range
do_writepages
ext4_writepages
mpage_map_and_submit_extent
mpage_map_one_extent
ext4_map_blocks
ext4_mb_new_blocks
ext4_mb_normalize_request
>>> start + size <= ac->ac_o_ex.fe_logical
ext4_mb_regular_allocator
ext4_mb_simple_scan_group
ext4_mb_use_best_found
ext4_mb_new_preallocation
ext4_mb_new_inode_pa
ext4_mb_use_inode_pa
>>> set ac->ac_b_ex.fe_len <= 0
ext4_mb_mark_diskspace_used
>>> BUG_ON(ac->ac_b_ex.fe_len <= 0);
we can easily reproduce this problem with the following commands:
`fallocate -l100M disk`
`mkfs.ext4 -b 1024 -g 256 disk`
`mount disk /mnt`
`fsstress -d /mnt -l 0 -n 1000 -p 1`
The size must be smaller than or equal to EXT4_BLOCKS_PER_GROUP.
Therefore, "start + size <= ac->ac_o_ex.fe_logical" may occur
when the size is truncated. So start should be the start position of
the group where ac_o_ex.fe_logical is located after alignment.
In addition, when the value of fe_logical or EXT4_BLOCKS_PER_GROUP
is very large, the value calculated by start_off is more accurate.
Cc: stable@kernel.org
Fixes: cd648b8a8f ("ext4: trim allocation requests to group size")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Baokun Li <libaokun1@huawei.com>
Reviewed-by: Ritesh Harjani <ritesh.list@gmail.com>
Link: https://lore.kernel.org/r/20220528110017.354175-2-libaokun1@huawei.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 85e123c27d upstream.
The code in dm-log rounds up bitset_size to 32 bits. It then uses
find_next_zero_bit_le on the allocated region. find_next_zero_bit_le
accesses the bitmap using unsigned long pointers. So, on 64-bit
architectures, it may access 4 bytes beyond the allocated size.
Fix this bug by rounding up bitset_size to BITS_PER_LONG.
This bug was found by running the lvm2 testsuite with kasan.
Fixes: 29121bd0b0 ("[PATCH] dm mirror log: bitset_size fix")
Cc: stable@vger.kernel.org
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 27071b5cbc ]
Even though the DW I2C controller reference clock source is requested by
the method devm_clk_get() with non-optional clock requirement the way the
clock handler is used afterwards has a pure optional clock semantic
(though in some circumstances we can get a warning about the clock missing
printed in the system console). There is no point in reimplementing that
functionality seeing the kernel clock framework already supports the
optional interface from scratch. Thus let's convert the platform driver to
using it.
Note by providing this commit we get to fix two problems. The first one
was introduced in commit c62ebb3d5f ("i2c: designware: Add support for
an interface clock"). It causes not having the interface clock (pclk)
enabled/disabled in case if the reference clock isn't provided. The second
problem was first introduced in commit b33af11de2 ("i2c: designware: Do
not require clock when SSCN and FFCN are provided"). Since that
modification the deferred probe procedure has been unsupported in case if
the interface clock isn't ready.
Fixes: c62ebb3d5f ("i2c: designware: Add support for an interface clock")
Fixes: b33af11de2 ("i2c: designware: Do not require clock when SSCN and FFCN are provided")
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ec8401a429 ]
of_get_child_by_name() returns a node pointer with refcount
incremented, we should use of_node_put() on it when not need anymore.
When kcalloc fails, it missing of_node_put() and results in refcount
leak. Fix this by goto out_put_node label.
Fixes: 52085d3f20 ("irqchip/gic-v3: Dynamically allocate PPI partition descriptors")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20220601080930.31005-5-linmq006@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dcea997bee ]
If a function lives in a section other than .text, but .text also exists
in the object, faddr2line may wrongly assume .text. This can result in
comically wrong output. For example:
$ scripts/faddr2line vmlinux.o enter_from_user_mode+0x1c
enter_from_user_mode+0x1c/0x30:
find_next_bit at /home/jpoimboe/git/linux/./include/linux/find.h:40
(inlined by) perf_clear_dirty_counters at /home/jpoimboe/git/linux/arch/x86/events/core.c:2504
Fix it by passing the section name to addr2line, unless the object file
is vmlinux, in which case the symbol table uses absolute addresses.
Fixes: 1d1a0e7c51 ("scripts/faddr2line: Fix overlapping text section failures")
Reported-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Josh Poimboeuf <jpoimboe@kernel.org>
Link: https://lore.kernel.org/r/7d25bc1408bd3a750ac26e60d2f2815a5f4a8363.1654130536.git.jpoimboe@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3eefdf9d1e ]
The branch range checks in ftrace_make_call() and ftrace_make_nop() are
incorrect, erroneously permitting a forwards branch of 128M and
erroneously rejecting a backwards branch of 128M.
This is because both functions calculate the offset backwards,
calculating the offset *from* the target *to* the branch, rather than
the other way around as the later comparisons expect.
If an out-of-range branch were erroeously permitted, this would later be
rejected by aarch64_insn_gen_branch_imm() as branch_imm_common() checks
the bounds correctly, resulting in warnings and the placement of a BRK
instruction. Note that this can only happen for a forwards branch of
exactly 128M, and so the caller would need to be exactly 128M bytes
below the relevant ftrace trampoline.
If an in-range branch were erroeously rejected, then:
* For modules when CONFIG_ARM64_MODULE_PLTS=y, this would result in the
use of a PLT entry, which is benign.
Note that this is the common case, as this is selected by
CONFIG_RANDOMIZE_BASE (and therefore RANDOMIZE_MODULE_REGION_FULL),
which distributions typically seelct. This is also selected by
CONFIG_ARM64_ERRATUM_843419.
* For modules when CONFIG_ARM64_MODULE_PLTS=n, this would result in
internal ftrace failures.
* For core kernel text, this would result in internal ftrace failues.
Note that for this to happen, the kernel text would need to be at
least 128M bytes in size, and typical configurations are smaller tha
this.
Fix this by calculating the offset *from* the branch *to* the target in
both functions.
Fixes: f8af0b364e ("arm64: ftrace: don't validate branch via PLT in ftrace_make_nop()")
Fixes: e71a4e1beb ("arm64: ftrace: add support for far branches to dynamic ftrace")
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Ard Biesheuvel <ardb@kernel.org>
Cc: Will Deacon <will@kernel.org>
Tested-by: "Ivan T. Ivanov" <iivanov@suse.de>
Reviewed-by: Chengming Zhou <zhouchengming@bytedance.com>
Reviewed-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://lore.kernel.org/r/20220614080944.1349146-2-mark.rutland@arm.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
