[ Upstream commit 973ae93d80 ]
tad_pmu_init() won't remove the callback added by cpuhp_setup_state_multi()
when platform_driver_register() failed. Remove the callback by
cpuhp_remove_multi_state() in fail path.
Similar to the handling of arm_ccn_init() in commit 26242b3300 ("bus:
arm-ccn: Prevent hotplug callback leak")
Fixes: 036a7584be ("drivers: perf: Add LLC-TAD perf counter support")
Signed-off-by: Yuan Can <yuancan@huawei.com>
Link: https://lore.kernel.org/r/20221115070207.32634-3-yuancan@huawei.com
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0bb1fbffc6 ]
Alexander noted that KFENCE only expects to handle faults from invalid page
table entries (i.e. translation faults), but arm64's fault handling logic will
call kfence_handle_page_fault() for other types of faults, including alignment
faults caused by unaligned atomics. This has the unfortunate property of
causing those other faults to be reported as "KFENCE: use-after-free",
which is misleading and hinders debugging.
Fix this by only forwarding unhandled translation faults to the KFENCE
code, similar to what x86 does already.
Alexander has verified that this passes all the tests in the KFENCE test
suite and avoids bogus reports on misaligned atomics.
Link: https://lore.kernel.org/all/20221102081620.1465154-1-zhongbaisong@huawei.com/
Fixes: 840b239863 ("arm64, kfence: enable KFENCE for ARM64")
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Alexander Potapenko <glider@google.com>
Tested-by: Alexander Potapenko <glider@google.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Marco Elver <elver@google.com>
Cc: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20221114104411.2853040-1-mark.rutland@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bdd28ab35c ]
\#pwm-cells for the Icicle kit's fabric PWM was incorrectly set to 2 &
blindly overridden by the (out of tree) driver anyway. The core can
support inverted operation, so update the entry to correctly report its
capabilities.
Fixes: 72560c6559 ("riscv: dts: microchip: add fpga fabric section to icicle kit")
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0336e2ce34 ]
Interrupt 12 of the Interrupt controller belongs to the SMI controller,
the right one for the display controller is the interrupt 13.
Fixes: 8113ba917d ("ARM: SPEAr: DT: Update device nodes")
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2927cf85f4 ]
To enable error reporting for a fabric to CCPLEX, we need to write its
register for enabling error interrupt to CCPLEX during boot and later
clear the error status register after error occurs. If a fabric's
registers are protected and not accessible from CCPLEX, then accessing
the registers will cause CBB firewall error.
Add support to check whether write access from CCPLEX to the registers
of a fabric is not blocked by it's firewall before enabling error
reporting to CCPLEX for that fabric.
Fixes: fc2f151d23 ("soc/tegra: cbb: Add driver for Tegra234 CBB 2.0")
Signed-off-by: Sumit Gupta <sumitg@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 55084947d6 ]
Added checks to avoid potential out of bounds errors which can happen if
the 'slave map' and 'CBB errors' arrays are not correct or latest where
some entries are missing.
Fixes: fc2f151d23 ("soc/tegra: cbb: Add driver for Tegra234 CBB 2.0")
Signed-off-by: Sumit Gupta <sumitg@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cd1d719b47 ]
Updating the slave map for fabrics and using the same maps for DCE, RCE
and SCE as they all are a replica in Tegra234.
Signed-off-by: Sumit Gupta <sumitg@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Stable-dep-of: 55084947d6 ("soc/tegra: cbb: Add checks for potential out of bound errors")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 33af51a652 ]
In Tegra194 SoC, master_id bit range is different between cluster NOC
and CBB NOC. Currently same bit range is used which results in wrong
master_id value. Due to this, illegal accesses from the CCPLEX master
do not result in a crash as expected. Fix this by using the correct
range for the CBB NOC.
Finally, it is only necessary to extract the master_id when the
erd_mask_inband_err flag is set because when this is not set, a crash
is always triggered.
Fixes: b713442214 ("soc/tegra: cbb: Add CBB 1.0 driver for Tegra194")
Fixes: fc2f151d23 ("soc/tegra: cbb: Add driver for Tegra234 CBB 2.0")
Signed-off-by: Sumit Gupta <sumitg@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8fbf94fea0 ]
The device_node pointer returned by of_find_matching_node() with
refcount incremented, when finish using it, the refcount need be
decreased.
Fixes: a967a289f1 ("RISC-V: sifive_l2_cache: Add L2 cache controller driver for SiFive SoCs")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a62d196e89 ]
corePWM is capable of inverted operation but the binding requires
\#pwm-cells of 2. Expand the binding to support setting the polarity.
Fixes: df77f77357 ("dt-bindings: pwm: add microchip corepwm binding")
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2ac909916b ]
The preferred form for Renesas' compatible strings is:
"<vendor>,<family>-<module>"
Somehow the compatible string for the r9a09g011 I2C IP was upstreamed
as renesas,i2c-r9a09g011 instead of renesas,r9a09g011-i2c, which
is really confusing, especially considering the generic fallback
is renesas,rzv2m-i2c.
The first user of renesas,i2c-r9a09g011 in the kernel is not yet in
a kernel release, it will be in v6.1, therefore it can still be
fixed in v6.1.
Even if we don't fix it before v6.2, I don't think there is any
harm in making such a change.
s/renesas,i2c-r9a09g011/renesas,r9a09g011-i2c/g for consistency.
Fixes: 54ac6794df ("arm64: dts: renesas: r9a09g011: Add i2c nodes")
Signed-off-by: Fabrizio Castro <fabrizio.castro.jz@renesas.com>
Link: https://lore.kernel.org/r/20221107165027.54150-3-fabrizio.castro.jz@renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 278f5015a3 ]
Although the HW User Manual for RZ/V2M states in the "Address Map"
section that the interrupt controller is assigned addresses starting
from 0x82000000, the memory locations from 0x82000000 0x0x8200FFFF
are marked as reserved in the "Interrupt Controller (GIC)" section
and are currently not used by the device tree, leading to the below
warning:
arch/arm64/boot/dts/renesas/r9a09g011.dtsi:51.38-63.5: Warning
(simple_bus_reg): /soc/interrupt-controller@82000000: simple-bus unit
address format error, expected "82010000"
Fix the unit address accordingly.
Fixes: fb1929b98f ("arm64: dts: renesas: Add initial DTSI for RZ/V2M SoC")
Signed-off-by: Fabrizio Castro <fabrizio.castro.jz@renesas.com>
Link: https://lore.kernel.org/r/20221103230648.53748-2-fabrizio.castro.jz@renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 64416ef0b0 ]
As serial communication requires a clean clock signal, the Serial
Communication Interfaces with FIFO (SCIF) are clocked by a clock that is
not affected by Spread Spectrum or Fractional Multiplication.
Hence change the clock input for the SCIF Baud Rate Generator internal
clock from the S0D3_PER clock to the SASYNCPERD1 clock (which has the
same clock rate), cfr. R-Car S4-8 Hardware User's Manual rev. 0.81.
Fixes: c62331e822 ("arm64: dts: renesas: Add Renesas R8A779F0 SoC support")
Fixes: 4075314425 ("arm64: dts: renesas: r8a779f0: Add SCIF nodes")
Reported-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20221103143440.46449-5-wsa+renesas@sang-engineering.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a5101ef18b ]
As serial communication requires a clean clock signal, the High Speed
Serial Communication Interfaces with FIFO (HSCIF) are clocked by a clock
that is not affected by Spread Spectrum or Fractional Multiplication.
Hence change the clock input for the HSCIF Baud Rate Generator internal
clock from the S0D3_PER clock to the SASYNCPERD1 clock (which has the
same clock rate), cfr. R-Car S4-8 Hardware User's Manual rev. 0.81.
Fixes: 01a787f78b ("arm64: dts: renesas: r8a779f0: Add HSCIF nodes")
Reported-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20221103143440.46449-4-wsa+renesas@sang-engineering.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d6105a8b7c ]
Evidently I forgot to update the unit address for the 38-bit cached
memory node when I changed the address in the reg property..
Update it to match.
Fixes: 6c11933017 ("riscv: dts: microchip: update memory configuration for v2022.10")
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b13b2c3e0e ]
Commit b9e8a7d950 ("firmware: ti_sci: Switch transport to polled
mode during system suspend") uses read_poll_timeout_atomic() macro
in ti_sci_do_xfer() to wait for completion when the system is
suspending. The break condition of the macro is set to "true" which
will cause it break immediately when evaluated, likely before the
TISCI xfer is completed, and always return 0. We want to poll here
until "done_state == true".
1) Change the break condition of read_poll_timeout_atomic() to
the bool variable "done_state".
2) The read_poll_timeout_atomic() returns 0 if the break condition
is met or -ETIMEDOUT if not. Since our break condition has changed
to "done_state", we also don't have to check for "!done_state" when
evaluating the return value.
Fixes: b9e8a7d950 ("firmware: ti_sci: Switch transport to polled mode during system suspend")
Signed-off-by: Georgi Vlaev <g-vlaev@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20221021185704.181316-1-g-vlaev@ti.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit adf85adc2a ]
There is a sparse warning shown below:
drivers/soc/ti/knav_qmss_queue.c:70:12: warning: symbol
'knav_acc_firmwares' was not declared. Should it be static?
Since 'knav_acc_firmwares' is only called within knav_qmss_queue.c,
mark it as static to fix the warning.
Fixes: 96ee19becc ("soc: ti: add firmware file name as part of the driver")
Signed-off-by: Chen Jiahao <chenjiahao16@huawei.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20221019153212.72350-1-chenjiahao16@huawei.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d5d577e3d5 ]
The WLAN regulator uses 'gpios' property instead of 'gpio' to specify
regulator enable GPIO. While the former is also currently handled by
the Linux kernel regulator-fixed driver, the later is the correct one
per DT bindings. Update the DT to use the later.
Fixes: 7dd5cbba42 ("ARM: dts: stm32: Enable WiFi on AV96")
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3b835f1b8a ]
The Avenger96 is populated with STM32MP157A DHCOR SoM, drop the
stm32mp15xc.dtsi which should only be included in DTs of devices
which are populated with STM32MP15xC/F SoC as the stm32mp15xc.dtsi
enables CRYP block not present in the STM32MP15xA/D SoC .
Fixes: 7e76f82acd ("ARM: dts: stm32: Split Avenger96 into DHCOR SoM and Avenger96 board")
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 63646fcba5 ]
Adds KCSAN's volatile instrumentation to objtool's uaccess whitelist.
Recent kernel change have shown that this was missing from the uaccess
whitelist (since the first upstreamed version of KCSAN):
mm/gup.o: warning: objtool: fault_in_readable+0x101: call to __tsan_volatile_write1() with UACCESS enabled
Fixes: 75d75b7a4d ("kcsan: Support distinguishing volatile accesses")
Signed-off-by: Marco Elver <elver@google.com>
Reviewed-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 574d6c59da ]
Drive strength macros defined for FSD platform is not reflecting actual
names and values as per HW UM. FSD SoC pinctrl has following four levels
of drive-strength and their corresponding values:
Level-1 <-> 0
Level-2 <-> 1
Level-4 <-> 2
Level-6 <-> 3
The commit 684dac402f ("arm64: dts: fsd: Add initial pinctrl support")
used drive strength macros defined for Exynos4 SoC family. For some IPs
the macros values of Exynos4 matched and worked well, but Exynos4 SoC
family drive-strength (names and values) is not exactly matching with
FSD SoC.
Fix the drive strength macros to reflect actual names and values given
in FSD HW UM.
Fixes: 684dac402f ("arm64: dts: fsd: Add initial pinctrl support")
Signed-off-by: Padmanabhan Rajanbabu <p.rajanbabu@samsung.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Link: https://lore.kernel.org/r/20221013104024.50179-2-p.rajanbabu@samsung.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ff02ac6216 ]
MSM8916 was originally using the "qcom,q6v5-pil" compatible for the
MSS remoteproc. Later it was decided to use SoC-specific compatibles
instead, so "qcom,msm8916-mss-pil" is now the preferred compatible.
Commit 60a05ed059 ("arm64: dts: qcom: msm8916: Add MSM8916-specific
compatibles to SCM/MSS") updated the MSM8916 device tree to make use of
the new compatible but still kept the old "qcom,q6v5-pil" as fallback.
This is inconsistent with other SoCs and conflicts with the description
in the binding documentation (which says that only one compatible should
be present). Also, it has no functional advantage since older kernels
could not handle this DT anyway (e.g. "power-domains" in the MSS node is
only supported by kernels that also support "qcom,msm8916-mss-pil").
Make this consistent with other SoCs by using only the
"qcom,msm8916-mss-pil" compatible.
Fixes: 60a05ed059 ("arm64: dts: qcom: msm8916: Add MSM8916-specific compatibles to SCM/MSS")
Signed-off-by: Stephan Gerhold <stephan.gerhold@kernkonzept.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220718140344.1831731-2-stephan.gerhold@kernkonzept.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
