[ Upstream commit fcd2e0deae ]
Currently we are not initializing the scmi clock with discrete rates
correctly. We fetch the min_rate and max_rate value only for clocks with
ranges and ignore the ones with discrete rates. This will lead to wrong
initialization of rate range when clock supports discrete rate.
Fix this by using the first and the last rate in the sorted list of the
discrete clock rates while registering the clock.
Link: https://lore.kernel.org/r/20200709081705.46084-2-sudeep.holla@arm.com
Fixes: 6d6a1d82ea ("clk: add support for clocks provided by SCMI")
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Reported-and-tested-by: Dien Pham <dien.pham.ry@renesas.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d81ae8aac8 ]
struct uclamp_rq was zeroed out entirely in assumption that in the first
call to uclamp_rq_inc() they'd be initialized correctly in accordance to
default settings.
But when next patch introduces a static key to skip
uclamp_rq_{inc,dec}() until userspace opts in to use uclamp, schedutil
will fail to perform any frequency changes because the
rq->uclamp[UCLAMP_MAX].value is zeroed at init and stays as such. Which
means all rqs are capped to 0 by default.
Fix it by making sure we do proper initialization at init without
relying on uclamp_rq_inc() doing it later.
Fixes: 69842cba9a ("sched/uclamp: Add CPU's clamp buckets refcounting")
Signed-off-by: Qais Yousef <qais.yousef@arm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Valentin Schneider <valentin.schneider@arm.com>
Tested-by: Lukasz Luba <lukasz.luba@arm.com>
Link: https://lkml.kernel.org/r/20200630112123.12076-2-qais.yousef@arm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b072714bfc ]
Once regulators are disabled after kernel boot, on Espresso board silent
hang observed because of LDO7 being disabled. LDO7 actually provide
power to CPU cores and non-cpu blocks circuitries. Keep this regulator
always-on to fix this hang.
Fixes: 9589f7721e ("arm64: dts: Add S2MPS15 PMIC node on exynos7-espresso")
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e0f1a30cf1 ]
When, at probe time, an SCMI communication failure inhibits the capacity
to query power domains states, such domains should be skipped.
Registering partially initialized SCMI power domains with genpd will
causes kernel panic.
arm-scmi timed out in resp(caller: scmi_power_state_get+0xa4/0xd0)
scmi-power-domain scmi_dev.2: failed to get state for domain 9
Unable to handle kernel NULL pointer dereference at virtual address 0000000000000000
Mem abort info:
ESR = 0x96000006
EC = 0x25: DABT (current EL), IL = 32 bits
SET = 0, FnV = 0
EA = 0, S1PTW = 0
Data abort info:
ISV = 0, ISS = 0x00000006
CM = 0, WnR = 0
user pgtable: 4k pages, 48-bit VAs, pgdp=00000009f3691000
[0000000000000000] pgd=00000009f1ca0003, p4d=00000009f1ca0003, pud=00000009f35ea003, pmd=0000000000000000
Internal error: Oops: 96000006 [#1] PREEMPT SMP
CPU: 2 PID: 381 Comm: bash Not tainted 5.8.0-rc1-00011-gebd118c2cca8 #2
Hardware name: ARM LTD ARM Juno Development Platform/ARM Juno Development Platform, BIOS EDK II Jan 3 2020
Internal error: Oops: 96000006 [#1] PREEMPT SMP
pstate: 80000005 (Nzcv daif -PAN -UAO BTYPE=--)
pc : of_genpd_add_provider_onecell+0x98/0x1f8
lr : of_genpd_add_provider_onecell+0x48/0x1f8
Call trace:
of_genpd_add_provider_onecell+0x98/0x1f8
scmi_pm_domain_probe+0x174/0x1e8
scmi_dev_probe+0x90/0xe0
really_probe+0xe4/0x448
driver_probe_device+0xfc/0x168
device_driver_attach+0x7c/0x88
bind_store+0xe8/0x128
drv_attr_store+0x2c/0x40
sysfs_kf_write+0x4c/0x60
kernfs_fop_write+0x114/0x230
__vfs_write+0x24/0x50
vfs_write+0xbc/0x1e0
ksys_write+0x70/0xf8
__arm64_sys_write+0x24/0x30
el0_svc_common.constprop.3+0x94/0x160
do_el0_svc+0x2c/0x98
el0_sync_handler+0x148/0x1a8
el0_sync+0x158/0x180
Do not register any power domain that failed to be queried with genpd.
Fixes: 898216c97e ("firmware: arm_scmi: add device power domain support using genpd")
Link: https://lore.kernel.org/r/20200619220330.12217-1-cristian.marussi@arm.com
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ea9dd8f61c ]
Call exynos_cpu_power_up(cpunr) unconditionally. This is needed by the
big.LITTLE cpuidle driver and has no side-effects on other code paths.
The additional soft-reset call during little core power up has been added
to properly boot all cores on the Exynos5422-based boards with secure
firmware (like Odroid XU3/XU4 family). This however broke big.LITTLE
CPUidle driver, which worked only on boards without secure firmware (like
Peach-Pit/Pi Chromebooks). Apply the workaround only when board is
running under secure firmware.
Fixes: 833b5794e3 ("ARM: EXYNOS: reset Little cores when cpu is up")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Lukasz Luba <lukasz.luba@arm.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bad8e64fb1 ]
On commit 6ac93117ab ("blktrace: use existing disk debugfs directory")
merged on v4.12 Omar fixed the original blktrace code for request-based
drivers (multiqueue). This however left in place a possible crash, if you
happen to abuse blktrace while racing to remove / add a device.
We used to use asynchronous removal of the request_queue, and with that
the issue was easier to reproduce. Now that we have reverted to
synchronous removal of the request_queue, the issue is still possible to
reproduce, its however just a bit more difficult.
We essentially run two instances of break-blktrace which add/remove
a loop device, and setup a blktrace and just never tear the blktrace
down. We do this twice in parallel. This is easily reproduced with the
script run_0004.sh from break-blktrace [0].
We can end up with two types of panics each reflecting where we
race, one a failed blktrace setup:
[ 252.426751] debugfs: Directory 'loop0' with parent 'block' already present!
[ 252.432265] BUG: kernel NULL pointer dereference, address: 00000000000000a0
[ 252.436592] #PF: supervisor write access in kernel mode
[ 252.439822] #PF: error_code(0x0002) - not-present page
[ 252.442967] PGD 0 P4D 0
[ 252.444656] Oops: 0002 [#1] SMP NOPTI
[ 252.446972] CPU: 10 PID: 1153 Comm: break-blktrace Tainted: G E 5.7.0-rc2-next-20200420+ #164
[ 252.452673] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.13.0-1 04/01/2014
[ 252.456343] RIP: 0010:down_write+0x15/0x40
[ 252.458146] Code: eb ca e8 ae 22 8d ff cc cc cc cc cc cc cc cc cc cc cc cc
cc cc 0f 1f 44 00 00 55 48 89 fd e8 52 db ff ff 31 c0 ba 01 00
00 00 <f0> 48 0f b1 55 00 75 0f 48 8b 04 25 c0 8b 01 00 48 89
45 08 5d
[ 252.463638] RSP: 0018:ffffa626415abcc8 EFLAGS: 00010246
[ 252.464950] RAX: 0000000000000000 RBX: ffff958c25f0f5c0 RCX: ffffff8100000000
[ 252.466727] RDX: 0000000000000001 RSI: ffffff8100000000 RDI: 00000000000000a0
[ 252.468482] RBP: 00000000000000a0 R08: 0000000000000000 R09: 0000000000000001
[ 252.470014] R10: 0000000000000000 R11: ffff958d1f9227ff R12: 0000000000000000
[ 252.471473] R13: ffff958c25ea5380 R14: ffffffff8cce15f1 R15: 00000000000000a0
[ 252.473346] FS: 00007f2e69dee540(0000) GS:ffff958c2fc80000(0000) knlGS:0000000000000000
[ 252.475225] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 252.476267] CR2: 00000000000000a0 CR3: 0000000427d10004 CR4: 0000000000360ee0
[ 252.477526] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[ 252.478776] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[ 252.479866] Call Trace:
[ 252.480322] simple_recursive_removal+0x4e/0x2e0
[ 252.481078] ? debugfs_remove+0x60/0x60
[ 252.481725] ? relay_destroy_buf+0x77/0xb0
[ 252.482662] debugfs_remove+0x40/0x60
[ 252.483518] blk_remove_buf_file_callback+0x5/0x10
[ 252.484328] relay_close_buf+0x2e/0x60
[ 252.484930] relay_open+0x1ce/0x2c0
[ 252.485520] do_blk_trace_setup+0x14f/0x2b0
[ 252.486187] __blk_trace_setup+0x54/0xb0
[ 252.486803] blk_trace_ioctl+0x90/0x140
[ 252.487423] ? do_sys_openat2+0x1ab/0x2d0
[ 252.488053] blkdev_ioctl+0x4d/0x260
[ 252.488636] block_ioctl+0x39/0x40
[ 252.489139] ksys_ioctl+0x87/0xc0
[ 252.489675] __x64_sys_ioctl+0x16/0x20
[ 252.490380] do_syscall_64+0x52/0x180
[ 252.491032] entry_SYSCALL_64_after_hwframe+0x44/0xa9
And the other on the device removal:
[ 128.528940] debugfs: Directory 'loop0' with parent 'block' already present!
[ 128.615325] BUG: kernel NULL pointer dereference, address: 00000000000000a0
[ 128.619537] #PF: supervisor write access in kernel mode
[ 128.622700] #PF: error_code(0x0002) - not-present page
[ 128.625842] PGD 0 P4D 0
[ 128.627585] Oops: 0002 [#1] SMP NOPTI
[ 128.629871] CPU: 12 PID: 544 Comm: break-blktrace Tainted: G E 5.7.0-rc2-next-20200420+ #164
[ 128.635595] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.13.0-1 04/01/2014
[ 128.640471] RIP: 0010:down_write+0x15/0x40
[ 128.643041] Code: eb ca e8 ae 22 8d ff cc cc cc cc cc cc cc cc cc cc cc cc
cc cc 0f 1f 44 00 00 55 48 89 fd e8 52 db ff ff 31 c0 ba 01 00
00 00 <f0> 48 0f b1 55 00 75 0f 65 48 8b 04 25 c0 8b 01 00 48 89
45 08 5d
[ 128.650180] RSP: 0018:ffffa9c3c05ebd78 EFLAGS: 00010246
[ 128.651820] RAX: 0000000000000000 RBX: ffff8ae9a6370240 RCX: ffffff8100000000
[ 128.653942] RDX: 0000000000000001 RSI: ffffff8100000000 RDI: 00000000000000a0
[ 128.655720] RBP: 00000000000000a0 R08: 0000000000000002 R09: ffff8ae9afd2d3d0
[ 128.657400] R10: 0000000000000056 R11: 0000000000000000 R12: 0000000000000000
[ 128.659099] R13: 0000000000000000 R14: 0000000000000003 R15: 00000000000000a0
[ 128.660500] FS: 00007febfd995540(0000) GS:ffff8ae9afd00000(0000) knlGS:0000000000000000
[ 128.662204] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 128.663426] CR2: 00000000000000a0 CR3: 0000000420042003 CR4: 0000000000360ee0
[ 128.664776] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[ 128.666022] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[ 128.667282] Call Trace:
[ 128.667801] simple_recursive_removal+0x4e/0x2e0
[ 128.668663] ? debugfs_remove+0x60/0x60
[ 128.669368] debugfs_remove+0x40/0x60
[ 128.669985] blk_trace_free+0xd/0x50
[ 128.670593] __blk_trace_remove+0x27/0x40
[ 128.671274] blk_trace_shutdown+0x30/0x40
[ 128.671935] blk_release_queue+0x95/0xf0
[ 128.672589] kobject_put+0xa5/0x1b0
[ 128.673188] disk_release+0xa2/0xc0
[ 128.673786] device_release+0x28/0x80
[ 128.674376] kobject_put+0xa5/0x1b0
[ 128.674915] loop_remove+0x39/0x50 [loop]
[ 128.675511] loop_control_ioctl+0x113/0x130 [loop]
[ 128.676199] ksys_ioctl+0x87/0xc0
[ 128.676708] __x64_sys_ioctl+0x16/0x20
[ 128.677274] do_syscall_64+0x52/0x180
[ 128.677823] entry_SYSCALL_64_after_hwframe+0x44/0xa9
The common theme here is:
debugfs: Directory 'loop0' with parent 'block' already present
This crash happens because of how blktrace uses the debugfs directory
where it places its files. Upon init we always create the same directory
which would be needed by blktrace but we only do this for make_request
drivers (multiqueue) block drivers. When you race a removal of these
devices with a blktrace setup you end up in a situation where the
make_request recursive debugfs removal will sweep away the blktrace
files and then later blktrace will also try to remove individual
dentries which are already NULL. The inverse is also possible and hence
the two types of use after frees.
We don't create the block debugfs directory on init for these types of
block devices:
* request-based block driver block devices
* every possible partition
* scsi-generic
And so, this race should in theory only be possible with make_request
drivers.
We can fix the UAF by simply re-using the debugfs directory for
make_request drivers (multiqueue) and only creating the ephemeral
directory for the other type of block devices. The new clarifications
on relying on the q->blk_trace_mutex *and* also checking for q->blk_trace
*prior* to processing a blktrace ensures the debugfs directories are
only created if no possible directory name clashes are possible.
This goes tested with:
o nvme partitions
o ISCSI with tgt, and blktracing against scsi-generic with:
o block
o tape
o cdrom
o media changer
o blktests
This patch is part of the work which disputes the severity of
CVE-2019-19770 which shows this issue is not a core debugfs issue, but
a misuse of debugfs within blktace.
Fixes: 6ac93117ab ("blktrace: use existing disk debugfs directory")
Reported-by: syzbot+603294af2d01acfdd6da@syzkaller.appspotmail.com
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: Bart Van Assche <bvanassche@acm.org>
Cc: Omar Sandoval <osandov@fb.com>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Nicolai Stange <nstange@suse.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: "James E.J. Bottomley" <jejb@linux.ibm.com>
Cc: yu kuai <yukuai3@huawei.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1b6a1a162d ]
msm8916-pins.dtsi specifies "bias-pull-none" for most of the audio
pin configurations. This was likely copied from the qcom kernel fork
where the same property was used for these audio pins.
However, "bias-pull-none" actually does not exist at all - not in
mainline and not in downstream. I can only guess that the original
intention was to configure "no pull", i.e. bias-disable.
Change it to that instead.
Fixes: 143bb9ad85 ("arm64: dts: qcom: add audio pinctrls")
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20200605185916.318494-2-stephan@gerhold.net
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3906f64022 ]
The crypto notify call occurs with a read mutex held so you must
not do any substantial work directly. In particular, you cannot
call crypto_alloc_* as they may trigger further notifications
which may dead-lock in the presence of another writer.
This patch fixes this by postponing the work into a work queue and
taking the same lock in the module init function.
While we're at it this patch also ensures that all RCU accesses are
marked appropriately (tested with sparse).
Finally this also reveals a race condition in module param show
function as it may be called prior to the module init function.
It's fixed by testing whether crct10dif_tfm is NULL (this is true
iff the init function has not completed assuming fallback is false).
Fixes: 11dcb1037f ("crc-t10dif: Allow current transform to be...")
Fixes: b76377543b ("crc-t10dif: Pick better transform if one...")
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 17ed808ad2 ]
When kobject_init_and_add() returns an error, it should be handled
because kobject_init_and_add() takes a reference even when it fails. If
this function returns an error, kobject_put() must be called to properly
clean up the memory associated with the object.
Therefore, replace calling kfree() and call kobject_put() and add a
missing kobject_put() in the edac_device_register_sysfs_main_kobj()
error path.
[ bp: Massage and merge into a single patch. ]
Fixes: b2ed215a33 ("Kobject: change drivers/edac to use kobject_init_and_add")
Signed-off-by: Qiushi Wu <wu000273@umn.edu>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lkml.kernel.org/r/20200528202238.18078-1-wu000273@umn.edu
Link: https://lkml.kernel.org/r/20200528203526.20908-1-wu000273@umn.edu
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8a445086f8 ]
The puma gmac node currently uses opposite active-values for the
gmac phy reset pin. The gpio-declaration uses active-high while the
separate snps,reset-active-low property marks the pin as active low.
While on the kernel side this works ok, other DT users may get
confused - as seen with uboot right now.
So bring this in line and make both properties match, similar to the
other Rockchip board.
Fixes: 2c66fc34e9 ("arm64: dts: rockchip: add RK3399-Q7 (Puma) SoM")
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Link: https://lore.kernel.org/r/20200603132836.362519-1-heiko@sntech.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7a7184f6cf ]
The puma vcc5v0_host regulator node currently uses opposite active-values
for the enable pin. The gpio-declaration uses active-high while the
separate enable-active-low property marks the pin as active low.
While on the kernel side this works ok, other DT users may get
confused - as seen with uboot right now.
So bring this in line and make both properties match, similar to the
gmac fix.
Fixes: 2c66fc34e9 ("arm64: dts: rockchip: add RK3399-Q7 (Puma) SoM")
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Link: https://lore.kernel.org/r/20200604091239.424318-1-heiko@sntech.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2300e6dab4 ]
The lion gmac node currently uses opposite active-values for the
gmac phy reset pin. The gpio-declaration uses active-high while the
separate snps,reset-active-low property marks the pin as active low.
While on the kernel side this works ok, other DT users may get
confused - as seen with uboot right now.
So bring this in line and make both properties match, similar to the
other Rockchip board.
Fixes: d99a02bcfa ("arm64: dts: rockchip: add RK3368-uQ7 (Lion) SoM")
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Link: https://lore.kernel.org/r/20200607212909.920575-1-heiko@sntech.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3ea2f097b1 ]
With commit:
'b7031a02ec75 ("sched/fair: Add NOHZ_STATS_KICK")'
rebalance_domains of the local cfs_rq happens before others idle cpus have
updated nohz.next_balance and its value is overwritten.
Move the update of nohz.next_balance for other idles cpus before balancing
and updating the next_balance of local cfs_rq.
Also, the nohz.next_balance is now updated only if all idle cpus got a
chance to rebalance their domains and the idle balance has not been aborted
because of new activities on the CPU. In case of need_resched, the idle
load balance will be kick the next jiffie in order to address remaining
ilb.
Fixes: b7031a02ec ("sched/fair: Add NOHZ_STATS_KICK")
Reported-by: Peng Liu <iwtbavbm@gmail.com>
Signed-off-by: Vincent Guittot <vincent.guittot@linaro.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Valentin Schneider <valentin.schneider@arm.com>
Acked-by: Mel Gorman <mgorman@suse.de>
Link: https://lkml.kernel.org/r/20200609123748.18636-1-vincent.guittot@linaro.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dad4e7fda4 ]
The current implementation always uses rpmh_write_async, which doesn't
wait for completion. That's fine for disable requests since there's no
immediate need for the clocks and they can be disabled in the
background. However, for enable requests we need to ensure the clocks
are actually enabled before returning to the client. Otherwise, clients
can end up accessing their HW before the necessary clocks are enabled,
which can lead to bus errors.
Use the synchronous version of this API (rpmh_write) for enable requests
in the active set to ensure completion.
Completion isn't required for sleep/wake sets, since they don't take
effect until after we enter sleep. All rpmh requests are automatically
flushed prior to entering sleep.
Fixes: 9c7e47025a ("clk: qcom: clk-rpmh: Add QCOM RPMh clock driver")
Signed-off-by: Mike Tipton <mdtipton@codeaurora.org>
Link: https://lkml.kernel.org/r/20200215021232.1149-1-mdtipton@codeaurora.org
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
[sboyd@kernel.org: Reorg code a bit for readability, rename to 'wait' to
make local variable not conflict with completion.h mechanism]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
the commit <a4d61e66ee4a> ("<io_uring: prevent re-read of sqe->opcode>")
caused another vulnerability. After io_get_req(), the sqe_submit struct
in req is not initialized, but the following code defaults that
req->submit.opcode is available.
Signed-off-by: Liu Yong <pkfxxxing@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 4f57cace81 upstream.
Some devices, particularly the 3DConnexion Spacemouse wireless 3D
controllers, return more than just the battery capacity in the battery
report. The Spacemouse devices return an additional byte with a device
specific field. However, hidinput_query_battery_capacity() only
requests a 2 byte transfer.
When a spacemouse is connected via USB (direct wire, no wireless dongle)
and it returns a 3 byte report instead of the assumed 2 byte battery
report the larger transfer confuses and frightens the USB subsystem
which chooses to ignore the transfer. Then after 2 seconds assume the
device has stopped responding and reset it. This can be reproduced
easily by using a wired connection with a wireless spacemouse. The
Spacemouse will enter a loop of resetting every 2 seconds which can be
observed in dmesg.
This patch solves the problem by increasing the transfer request to 4
bytes instead of 2. The fix isn't particularly elegant, but it is simple
and safe to backport to stable kernels. A further patch will follow to
more elegantly handle battery reports that contain additional data.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Darren Hart <darren@dvhart.com>
Cc: Jiri Kosina <jikos@kernel.org>
Cc: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Cc: stable@vger.kernel.org
Tested-by: Darren Hart <dvhart@infradead.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f3751ad011 upstream.
__tracepoint_string's have their string data stored in .rodata, and an
address to that data stored in the "__tracepoint_str" section. Functions
that refer to those strings refer to the symbol of the address. Compiler
optimization can replace those address references with references
directly to the string data. If the address doesn't appear to have other
uses, then it appears dead to the compiler and is removed. This can
break the /tracing/printk_formats sysfs node which iterates the
addresses stored in the "__tracepoint_str" section.
Like other strings stored in custom sections in this header, mark these
__used to inform the compiler that there are other non-obvious users of
the address, so they should still be emitted.
Link: https://lkml.kernel.org/r/20200730224555.2142154-2-ndesaulniers@google.com
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Miguel Ojeda <miguel.ojeda.sandonis@gmail.com>
Cc: stable@vger.kernel.org
Fixes: 102c9323c3 ("tracing: Add __tracepoint_string() to export string pointers")
Reported-by: Tim Murray <timmurray@google.com>
Reported-by: Simon MacMullen <simonmacm@google.com>
Suggested-by: Greg Hackmann <ghackmann@google.com>
Signed-off-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 412055398b upstream.
svcrdma expects that the payload falls precisely into the xdr_buf
page vector. This does not seem to be the case for
nfsd4_encode_readv().
This code is called only when fops->splice_read is missing or when
RQ_SPLICE_OK is clear, so it's not a noticeable problem in many
common cases.
Add new transport method: ->xpo_read_payload so that when a READ
payload does not fit exactly in rq_res's page vector, the XDR
encoder can inform the RPC transport exactly where that payload is,
without the payload's XDR pad.
That way, when a Write chunk is present, the transport knows what
byte range in the Reply message is supposed to be matched with the
chunk.
Note that the Linux NFS server implementation of NFS/RDMA can
currently handle only one Write chunk per RPC-over-RDMA message.
This simplifies the implementation of this fix.
Fixes: b042098063 ("nfsd4: allow exotic read compounds")
Buglink: https://bugzilla.kernel.org/show_bug.cgi?id=198053
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Cc: Timo Rothenpieler <timo@rothenpieler.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 311aa6aafe upstream.
The IMA_APPRAISE_BOOTPARAM config allows enabling different "ima_appraise="
modes - log, fix, enforce - at run time, but not when IMA architecture
specific policies are enabled. This prevents properly labeling the
filesystem on systems where secure boot is supported, but not enabled on the
platform. Only when secure boot is actually enabled should these IMA
appraise modes be disabled.
This patch removes the compile time dependency and makes it a runtime
decision, based on the secure boot state of that platform.
Test results as follows:
-> x86-64 with secure boot enabled
[ 0.015637] Kernel command line: <...> ima_policy=appraise_tcb ima_appraise=fix
[ 0.015668] ima: Secure boot enabled: ignoring ima_appraise=fix boot parameter option
-> powerpc with secure boot disabled
[ 0.000000] Kernel command line: <...> ima_policy=appraise_tcb ima_appraise=fix
[ 0.000000] Secure boot mode disabled
-> Running the system without secure boot and with both options set:
CONFIG_IMA_APPRAISE_BOOTPARAM=y
CONFIG_IMA_ARCH_POLICY=y
Audit prompts "missing-hash" but still allow execution and, consequently,
filesystem labeling:
type=INTEGRITY_DATA msg=audit(07/09/2020 12:30:27.778:1691) : pid=4976
uid=root auid=root ses=2
subj=unconfined_u:unconfined_r:unconfined_t:s0-s0:c0.c1023 op=appraise_data
cause=missing-hash comm=bash name=/usr/bin/evmctl dev="dm-0" ino=493150
res=no
Cc: stable@vger.kernel.org
Fixes: d958083a8f ("x86/ima: define arch_get_ima_policy() for x86")
Signed-off-by: Bruno Meneguele <bmeneg@redhat.com>
Cc: stable@vger.kernel.org # 5.0
Signed-off-by: Mimi Zohar <zohar@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 730e700e2c ]
For retransmitted packets, TCP needs to resort to using TCP timestamps
for computing RTT samples. In the common case where the data and ACK
fall in the same 1-millisecond interval, TCP senders with millisecond-
granularity TCP timestamps compute a ca_rtt_us of 0. This ca_rtt_us
of 0 propagates to rs->rtt_us.
This value of 0 can cause performance problems for congestion control
modules. For example, in BBR, the zero min_rtt sample can bring the
min_rtt and BDP estimate down to 0, reduce snd_cwnd and result in a
low throughput. It would be hard to mitigate this with filtering in
the congestion control module, because the proper floor to apply would
depend on the method of RTT sampling (using timestamp options or
internally-saved transmission timestamps).
This fix applies a floor of 1 for the RTT sample delta from TCP
timestamps, so that seq_rtt_us, ca_rtt_us, and rs->rtt_us will be at
least 1 * (USEC_PER_SEC / TCP_TS_HZ).
Note that the receiver RTT computation in tcp_rcv_rtt_measure() and
min_rtt computation in tcp_update_rtt_min() both already apply a floor
of 1 timestamp tick, so this commit makes the code more consistent in
avoiding this edge case of a value of 0.
Signed-off-by: Jianfeng Wang <jfwang@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Kevin Yang <yyd@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 16f6458f24 ]
The msg_zerocopy test pins the sender and receiver threads to separate
cores to reduce variance between runs.
But it hardcodes the cores and skips core 0, so it fails on machines
with the selected cores offline, or simply fewer cores.
The test mainly gives code coverage in automated runs. The throughput
of zerocopy ('-z') and non-zerocopy runs is logged for manual
inspection.
Continue even when sched_setaffinity fails. Just log to warn anyone
interpreting the data.
Fixes: 07b65c5b31 ("test: add msg_zerocopy test")
Reported-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Acked-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a0dced17ad ]
This reverts commit 71130f2997.
In commit 71130f2997 ("vxlan: fix tos value before xmit") we want to
make sure the tos value are filtered by RT_TOS() based on RFC1349.
0 1 2 3 4 5 6 7
+-----+-----+-----+-----+-----+-----+-----+-----+
| PRECEDENCE | TOS | MBZ |
+-----+-----+-----+-----+-----+-----+-----+-----+
But RFC1349 has been obsoleted by RFC2474. The new DSCP field defined like
0 1 2 3 4 5 6 7
+-----+-----+-----+-----+-----+-----+-----+-----+
| DS FIELD, DSCP | ECN FIELD |
+-----+-----+-----+-----+-----+-----+-----+-----+
So with
IPTOS_TOS_MASK 0x1E
RT_TOS(tos) ((tos)&IPTOS_TOS_MASK)
the first 3 bits DSCP info will get lost.
To take all the DSCP info in xmit, we should revert the patch and just push
all tos bits to ip_tunnel_ecn_encap(), which will handling ECN field later.
Fixes: 71130f2997 ("vxlan: fix tos value before xmit")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Acked-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9aba6c5b49 ]
ovs_ct_put_key() is potentially copying uninitialized kernel stack memory
into socket buffers, since the compiler may leave a 3-byte hole at the end
of `struct ovs_key_ct_tuple_ipv4` and `struct ovs_key_ct_tuple_ipv6`. Fix
it by initializing `orig` with memset().
Fixes: 9dd7f8907c ("openvswitch: Add original direction conntrack tuple to sw_flow_key.")
Suggested-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Peilin Ye <yepeilin.cs@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit bab9693a9a ]
A dead lock was triggered on thunderx driver:
CPU0 CPU1
---- ----
[01] lock(&(&nic->rx_mode_wq_lock)->rlock);
[11] lock(&(&mc->mca_lock)->rlock);
[12] lock(&(&nic->rx_mode_wq_lock)->rlock);
[02] <Interrupt> lock(&(&mc->mca_lock)->rlock);
The path for each is:
[01] worker_thread() -> process_one_work() -> nicvf_set_rx_mode_task()
[02] mld_ifc_timer_expire()
[11] ipv6_add_dev() -> ipv6_dev_mc_inc() -> igmp6_group_added() ->
[12] dev_mc_add() -> __dev_set_rx_mode() -> nicvf_set_rx_mode()
To fix it, it needs to disable bh on [1], so that the timer on [2]
wouldn't be triggered until rx_mode_wq_lock is released. So change
to use spin_lock_bh() instead of spin_lock().
Thanks to Paolo for helping with this.
v1->v2:
- post to netdev.
Reported-by: Rafael P. <rparrazo@redhat.com>
Tested-by: Dean Nelson <dnelson@redhat.com>
Fixes: 469998c861 ("net: thunderx: prevent concurrent data re-writing by nicvf_set_rx_mode")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 622e32b7d4 ]
The GRE tunnel can be used to transport traffic that does not rely on a
Internet checksum (e.g. SCTP). The issue can be triggered creating a GRE
or GRETAP tunnel and transmitting SCTP traffic ontop of it where CRC
offload has been disabled. In order to fix the issue we need to
recompute the GRE csum in gre_gso_segment() not relying on the inner
checksum.
The issue is still present when we have the CRC offload enabled.
In this case we need to disable the CRC offload if we require GRE
checksum since otherwise skb_checksum() will report a wrong value.
Fixes: 90017accff ("sctp: Add GSO support")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Reviewed-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 7c9864bbcc ]
If the accelerated networking SRIOV VF device has lost carrier
use the synthetic network device which is available as backup
path. This is a rare case since if VF link goes down, normally
the VMBus device will also loose external connectivity as well.
But if the communication is between two VM's on the same host
the VMBus device will still work.
Reported-by: "Shah, Ashish N" <ashish.n.shah@intel.com>
Fixes: 0c195567a8 ("netvsc: transparent VF management")
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 02afa9c66b ]
Fix smatch warning:
drivers/net/ethernet/freescale/dpaa2/dpaa2-eth.c:2419
alloc_channel() warn: passing zero to 'ERR_PTR'
setup_dpcon() should return ERR_PTR(err) instead of zero in error
handling case.
Fixes: d7f5a9d89a ("dpaa2-eth: defer probe on object allocate")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ea060b3526 ]
Drop the bogus endpoint-lookup helper which could end up accepting
interfaces based on endpoints belonging to unrelated altsettings.
Note that the returned bulk pipes and interrupt endpoint descriptor
were never actually used. Instead the bulk-endpoint numbers are
hardcoded to 1 and 2 (matching the specification), while the interrupt-
endpoint descriptor was assumed to be the third descriptor created by
USB core.
Try to bring some order to this by dropping the bogus lookup helper and
adding the missing endpoint sanity checks while keeping the interrupt-
descriptor assumption for now.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b5141915b5 ]
The commit cited below removed the RCU read-side critical section from
rtnl_fdb_dump() which means that the ndo_fdb_dump() callback is invoked
without RCU protection.
This results in the following warning [1] in the VXLAN driver, which
relied on the callback being invoked from an RCU read-side critical
section.
Fix this by calling rcu_read_lock() in the VXLAN driver, as already done
in the bridge driver.
[1]
WARNING: suspicious RCU usage
5.8.0-rc4-custom-01521-g481007553ce6 #29 Not tainted
-----------------------------
drivers/net/vxlan.c:1379 RCU-list traversed in non-reader section!!
other info that might help us debug this:
rcu_scheduler_active = 2, debug_locks = 1
1 lock held by bridge/166:
#0: ffffffff85a27850 (rtnl_mutex){+.+.}-{3:3}, at: netlink_dump+0xea/0x1090
stack backtrace:
CPU: 1 PID: 166 Comm: bridge Not tainted 5.8.0-rc4-custom-01521-g481007553ce6 #29
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.13.0-2.fc32 04/01/2014
Call Trace:
dump_stack+0x100/0x184
lockdep_rcu_suspicious+0x153/0x15d
vxlan_fdb_dump+0x51e/0x6d0
rtnl_fdb_dump+0x4dc/0xad0
netlink_dump+0x540/0x1090
__netlink_dump_start+0x695/0x950
rtnetlink_rcv_msg+0x802/0xbd0
netlink_rcv_skb+0x17a/0x480
rtnetlink_rcv+0x22/0x30
netlink_unicast+0x5ae/0x890
netlink_sendmsg+0x98a/0xf40
__sys_sendto+0x279/0x3b0
__x64_sys_sendto+0xe6/0x1a0
do_syscall_64+0x54/0xa0
entry_SYSCALL_64_after_hwframe+0x44/0xa9
RIP: 0033:0x7fe14fa2ade0
Code: Bad RIP value.
RSP: 002b:00007fff75bb5b88 EFLAGS: 00000246 ORIG_RAX: 000000000000002c
RAX: ffffffffffffffda RBX: 00005614b1ba0020 RCX: 00007fe14fa2ade0
RDX: 000000000000011c RSI: 00007fff75bb5b90 RDI: 0000000000000003
RBP: 00007fff75bb5b90 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000246 R12: 00005614b1b89160
R13: 0000000000000000 R14: 0000000000000000 R15: 0000000000000000
Fixes: 5e6d243587 ("bridge: netlink dump interface at par with brctl")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 65550098c1 ]
There's a race between rxrpc_sendmsg setting up a call, but then failing to
send anything on it due to an error, and recvmsg() seeing the call
completion occur and trying to return the state to the user.
An assertion fails in rxrpc_recvmsg() because the call has already been
released from the socket and is about to be released again as recvmsg deals
with it. (The recvmsg_q queue on the socket holds a ref, so there's no
problem with use-after-free.)
We also have to be careful not to end up reporting an error twice, in such
a way that both returns indicate to userspace that the user ID supplied
with the call is no longer in use - which could cause the client to
malfunction if it recycles the user ID fast enough.
Fix this by the following means:
(1) When sendmsg() creates a call after the point that the call has been
successfully added to the socket, don't return any errors through
sendmsg(), but rather complete the call and let recvmsg() retrieve
them. Make sendmsg() return 0 at this point. Further calls to
sendmsg() for that call will fail with ESHUTDOWN.
Note that at this point, we haven't send any packets yet, so the
server doesn't yet know about the call.
(2) If sendmsg() returns an error when it was expected to create a new
call, it means that the user ID wasn't used.
(3) Mark the call disconnected before marking it completed to prevent an
oops in rxrpc_release_call().
(4) recvmsg() will then retrieve the error and set MSG_EOR to indicate
that the user ID is no longer known by the kernel.
An oops like the following is produced:
kernel BUG at net/rxrpc/recvmsg.c:605!
...
RIP: 0010:rxrpc_recvmsg+0x256/0x5ae
...
Call Trace:
? __init_waitqueue_head+0x2f/0x2f
____sys_recvmsg+0x8a/0x148
? import_iovec+0x69/0x9c
? copy_msghdr_from_user+0x5c/0x86
___sys_recvmsg+0x72/0xaa
? __fget_files+0x22/0x57
? __fget_light+0x46/0x51
? fdget+0x9/0x1b
do_recvmmsg+0x15e/0x232
? _raw_spin_unlock+0xa/0xb
? vtime_delta+0xf/0x25
__x64_sys_recvmmsg+0x2c/0x2f
do_syscall_64+0x4c/0x78
entry_SYSCALL_64_after_hwframe+0x44/0xa9
Fixes: 357f5ef646 ("rxrpc: Call rxrpc_release_call() on error in rxrpc_new_client_call()")
Reported-by: syzbot+b54969381df354936d96@syzkaller.appspotmail.com
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Marc Dionne <marc.dionne@auristor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 555a893303 ]
in recent kernel versions there are warnings about incorrect MTU size
like these:
eth0: mtu greater than device maximum
mtk_soc_eth 1b100000.ethernet eth0: error -22 setting MTU to include DSA overhead
Fixes: bfcb813203 ("net: dsa: configure the MTU for switch ports")
Fixes: 72579e14a1 ("net: dsa: don't fail to probe if we couldn't set the MTU")
Fixes: 7a4c53bee3 ("net: report invalid mtu value via netlink extack")
Signed-off-by: Landen Chao <landen.chao@mediatek.com>
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 706ec91916 ]
ip6_route_info_create() invokes nexthop_get(), which increases the
refcount of the "nh".
When ip6_route_info_create() returns, local variable "nh" becomes
invalid, so the refcount should be decreased to keep refcount balanced.
The reference counting issue happens in one exception handling path of
ip6_route_info_create(). When nexthops can not be used with source
routing, the function forgets to decrease the refcnt increased by
nexthop_get(), causing a refcnt leak.
Fix this issue by pulling up the error source routing handling when
nexthops can not be used with source routing.
Fixes: f88d8ea67f ("ipv6: Plumb support for nexthop object in a fib6_info")
Signed-off-by: Xiyu Yang <xiyuyang19@fudan.edu.cn>
Signed-off-by: Xin Tan <tanxin.ctf@gmail.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 8c0de6e96c ]
IPV6_ADDRFORM causes resource leaks when converting an IPv6 socket
to IPv4, particularly struct ipv6_ac_socklist. Similar to
struct ipv6_mc_socklist, we should just close it on this path.
This bug can be easily reproduced with the following C program:
#include <stdio.h>
#include <string.h>
#include <sys/types.h>
#include <sys/socket.h>
#include <arpa/inet.h>
int main()
{
int s, value;
struct sockaddr_in6 addr;
struct ipv6_mreq m6;
s = socket(AF_INET6, SOCK_DGRAM, 0);
addr.sin6_family = AF_INET6;
addr.sin6_port = htons(5000);
inet_pton(AF_INET6, "::ffff:192.168.122.194", &addr.sin6_addr);
connect(s, (struct sockaddr *)&addr, sizeof(addr));
inet_pton(AF_INET6, "fe80::AAAA", &m6.ipv6mr_multiaddr);
m6.ipv6mr_interface = 5;
setsockopt(s, SOL_IPV6, IPV6_JOIN_ANYCAST, &m6, sizeof(m6));
value = AF_INET;
setsockopt(s, SOL_IPV6, IPV6_ADDRFORM, &value, sizeof(value));
close(s);
return 0;
}
Reported-by: ch3332xr@gmail.com
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 83f3522860 ]
fib_trie_unmerge() is called with RTNL held, but not from an RCU
read-side critical section. This leads to the following warning [1] when
the FIB alias list in a leaf is traversed with
hlist_for_each_entry_rcu().
Since the function is always called with RTNL held and since
modification of the list is protected by RTNL, simply use
hlist_for_each_entry() and silence the warning.
[1]
WARNING: suspicious RCU usage
5.8.0-rc4-custom-01520-gc1f937f3f83b #30 Not tainted
-----------------------------
net/ipv4/fib_trie.c:1867 RCU-list traversed in non-reader section!!
other info that might help us debug this:
rcu_scheduler_active = 2, debug_locks = 1
1 lock held by ip/164:
#0: ffffffff85a27850 (rtnl_mutex){+.+.}-{3:3}, at: rtnetlink_rcv_msg+0x49a/0xbd0
stack backtrace:
CPU: 0 PID: 164 Comm: ip Not tainted 5.8.0-rc4-custom-01520-gc1f937f3f83b #30
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.13.0-2.fc32 04/01/2014
Call Trace:
dump_stack+0x100/0x184
lockdep_rcu_suspicious+0x153/0x15d
fib_trie_unmerge+0x608/0xdb0
fib_unmerge+0x44/0x360
fib4_rule_configure+0xc8/0xad0
fib_nl_newrule+0x37a/0x1dd0
rtnetlink_rcv_msg+0x4f7/0xbd0
netlink_rcv_skb+0x17a/0x480
rtnetlink_rcv+0x22/0x30
netlink_unicast+0x5ae/0x890
netlink_sendmsg+0x98a/0xf40
____sys_sendmsg+0x879/0xa00
___sys_sendmsg+0x122/0x190
__sys_sendmsg+0x103/0x1d0
__x64_sys_sendmsg+0x7d/0xb0
do_syscall_64+0x54/0xa0
entry_SYSCALL_64_after_hwframe+0x44/0xa9
RIP: 0033:0x7fc80a234e97
Code: Bad RIP value.
RSP: 002b:00007ffef8b66798 EFLAGS: 00000246 ORIG_RAX: 000000000000002e
RAX: ffffffffffffffda RBX: 0000000000000000 RCX: 00007fc80a234e97
RDX: 0000000000000000 RSI: 00007ffef8b66800 RDI: 0000000000000003
RBP: 000000005f141b1c R08: 0000000000000001 R09: 0000000000000000
R10: 00007fc80a2a8ac0 R11: 0000000000000246 R12: 0000000000000001
R13: 0000000000000000 R14: 00007ffef8b67008 R15: 0000556fccb10020
Fixes: 0ddcf43d5d ("ipv4: FIB Local/MAIN table collapse")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e7b856dfce upstream.
As reported in https://bugzilla.kernel.org/206217 , raw_violation_fixup
is causing more harm than good in some common use-cases.
This patch is a partial revert of commit:
191cd6fb5d ("PCI: tegra: Add SW fixup for RAW violations")
and fixes the following regression since then.
* Description:
When both the NIC and MMC are used one can see the following message:
NETDEV WATCHDOG: enp1s0 (r8169): transmit queue 0 timed out
and
pcieport 0000:00:02.0: AER: Uncorrected (Non-Fatal) error received: 0000:01:00.0
r8169 0000:01:00.0: AER: PCIe Bus Error: severity=Uncorrected (Non-Fatal), type=Transaction Layer, (Requester ID)
r8169 0000:01:00.0: AER: device [10ec:8168] error status/mask=00004000/00400000
r8169 0000:01:00.0: AER: [14] CmpltTO (First)
r8169 0000:01:00.0: AER: can't recover (no error_detected callback)
pcieport 0000:00:02.0: AER: device recovery failed
After that, the ethernet NIC is not functional anymore even after
reloading the r8169 module. After a reboot, this is reproducible by
copying a large file over the NIC to the MMC.
For some reason this is not reproducible when files are copied to a tmpfs.
* Little background on the fixup, by Manikanta Maddireddy:
"In the internal testing with dGPU on Tegra124, CmplTO is reported by
dGPU. This happened because FIFO queue in AFI(AXI to PCIe) module
get full by upstream posted writes. Back to back upstream writes
interleaved with infrequent reads, triggers RAW violation and CmpltTO.
This is fixed by reducing the posted write credits and by changing
updateFC timer frequency. These settings are fixed after stress test.
In the current case, RTL NIC is also reporting CmplTO. These settings
seems to be aggravating the issue instead of fixing it."
Link: https://lore.kernel.org/r/20200718100710.15398-1-kwizart@gmail.com
Fixes: 191cd6fb5d ("PCI: tegra: Add SW fixup for RAW violations")
Signed-off-by: Nicolas Chauvet <kwizart@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Manikanta Maddireddy <mmaddireddy@nvidia.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 08b5d5014a upstream.
set/removexattr on an exported filesystem should break NFS delegations.
This is true in general, but also for the upcoming support for
RFC 8726 (NFSv4 extended attribute support). Make sure that they do.
Additionally, they need to grow a _locked variant, since callers might
call this with i_rwsem held (like the NFS server code).
Cc: stable@vger.kernel.org # v4.9+
Cc: linux-fsdevel@vger.kernel.org
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Frank van der Linden <fllinden@amazon.com>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ddc9d357b9 ]
When a Linux hv_sock app tries to connect to a Service GUID on which no
host app is listening, a recent host (RS3+) sends a
CHANNELMSG_TL_CONNECT_RESULT (23) message to Linux and this triggers such
a warning:
unknown msgtype=23
WARNING: CPU: 2 PID: 0 at drivers/hv/vmbus_drv.c:1031 vmbus_on_msg_dpc
Actually Linux can safely ignore the message because the Linux app's
connect() will time out in 2 seconds: see VSOCK_DEFAULT_CONNECT_TIMEOUT
and vsock_stream_connect(). We don't bother to make use of the message
because: 1) it's only supported on recent hosts; 2) a non-trivial effort
is required to use the message in Linux, but the benefit is small.
So, let's not see the warning by silently ignoring the message.
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e24c6447cc ]
I compiled with AddressSanitizer and I had these memory leaks while I
was using the tep_parse_format function:
Direct leak of 28 byte(s) in 4 object(s) allocated from:
#0 0x7fb07db49ffe in __interceptor_realloc (/lib/x86_64-linux-gnu/libasan.so.5+0x10dffe)
#1 0x7fb07a724228 in extend_token /home/pduplessis/repo/linux/tools/lib/traceevent/event-parse.c:985
#2 0x7fb07a724c21 in __read_token /home/pduplessis/repo/linux/tools/lib/traceevent/event-parse.c:1140
#3 0x7fb07a724f78 in read_token /home/pduplessis/repo/linux/tools/lib/traceevent/event-parse.c:1206
#4 0x7fb07a725191 in __read_expect_type /home/pduplessis/repo/linux/tools/lib/traceevent/event-parse.c:1291
#5 0x7fb07a7251df in read_expect_type /home/pduplessis/repo/linux/tools/lib/traceevent/event-parse.c:1299
#6 0x7fb07a72e6c8 in process_dynamic_array_len /home/pduplessis/repo/linux/tools/lib/traceevent/event-parse.c:2849
#7 0x7fb07a7304b8 in process_function /home/pduplessis/repo/linux/tools/lib/traceevent/event-parse.c:3161
#8 0x7fb07a730900 in process_arg_token /home/pduplessis/repo/linux/tools/lib/traceevent/event-parse.c:3207
#9 0x7fb07a727c0b in process_arg /home/pduplessis/repo/linux/tools/lib/traceevent/event-parse.c:1786
#10 0x7fb07a731080 in event_read_print_args /home/pduplessis/repo/linux/tools/lib/traceevent/event-parse.c:3285
#11 0x7fb07a731722 in event_read_print /home/pduplessis/repo/linux/tools/lib/traceevent/event-parse.c:3369
#12 0x7fb07a740054 in __tep_parse_format /home/pduplessis/repo/linux/tools/lib/traceevent/event-parse.c:6335
#13 0x7fb07a74047a in __parse_event /home/pduplessis/repo/linux/tools/lib/traceevent/event-parse.c:6389
#14 0x7fb07a740536 in tep_parse_format /home/pduplessis/repo/linux/tools/lib/traceevent/event-parse.c:6431
#15 0x7fb07a785acf in parse_event ../../../src/fs-src/fs.c:251
#16 0x7fb07a785ccd in parse_systems ../../../src/fs-src/fs.c:284
#17 0x7fb07a786fb3 in read_metadata ../../../src/fs-src/fs.c:593
#18 0x7fb07a78760e in ftrace_fs_source_init ../../../src/fs-src/fs.c:727
#19 0x7fb07d90c19c in add_component_with_init_method_data ../../../../src/lib/graph/graph.c:1048
#20 0x7fb07d90c87b in add_source_component_with_initialize_method_data ../../../../src/lib/graph/graph.c:1127
#21 0x7fb07d90c92a in bt_graph_add_source_component ../../../../src/lib/graph/graph.c:1152
#22 0x55db11aa632e in cmd_run_ctx_create_components_from_config_components ../../../src/cli/babeltrace2.c:2252
#23 0x55db11aa6fda in cmd_run_ctx_create_components ../../../src/cli/babeltrace2.c:2347
#24 0x55db11aa780c in cmd_run ../../../src/cli/babeltrace2.c:2461
#25 0x55db11aa8a7d in main ../../../src/cli/babeltrace2.c:2673
#26 0x7fb07d5460b2 in __libc_start_main (/lib/x86_64-linux-gnu/libc.so.6+0x270b2)
The token variable in the process_dynamic_array_len function is
allocated in the read_expect_type function, but is not freed before
calling the read_token function.
Free the token variable before calling read_token in order to plug the
leak.
Signed-off-by: Philippe Duplessis-Guindon <pduplessis@efficios.com>
Reviewed-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Link: https://lore.kernel.org/linux-trace-devel/20200730150236.5392-1-pduplessis@efficios.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 51875dad43 ]
atmtcp_remove_persistent() invokes atm_dev_lookup(), which returns a
reference of atm_dev with increased refcount or NULL if fails.
The refcount leaks issues occur in two error handling paths. If
dev_data->persist is zero or PRIV(dev)->vcc isn't NULL, the function
returns 0 without decreasing the refcount kept by a local variable,
resulting in refcount leaks.
Fix the issue by adding atm_dev_put() before returning 0 both when
dev_data->persist is zero or PRIV(dev)->vcc isn't NULL.
Signed-off-by: Xin Xiong <xiongx18@fudan.edu.cn>
Signed-off-by: Xiyu Yang <xiyuyang19@fudan.edu.cn>
Signed-off-by: Xin Tan <tanxin.ctf@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 024a8168b7 ]
We observed two panics involving races with igb_reset_task.
The first panic is caused by this race condition:
kworker reboot -f
igb_reset_task
igb_reinit_locked
igb_down
napi_synchronize
__igb_shutdown
igb_clear_interrupt_scheme
igb_free_q_vectors
igb_free_q_vector
adapter->q_vector[v_idx] = NULL;
napi_disable
Panics trying to access
adapter->q_vector[v_idx].napi_state
The second panic (a divide error) is caused by this race:
kworker reboot -f tx packet
igb_reset_task
__igb_shutdown
rtnl_lock()
...
igb_clear_interrupt_scheme
igb_free_q_vectors
adapter->num_tx_queues = 0
...
rtnl_unlock()
rtnl_lock()
igb_reinit_locked
igb_down
igb_up
netif_tx_start_all_queues
dev_hard_start_xmit
igb_xmit_frame
igb_tx_queue_mapping
Panics on
r_idx % adapter->num_tx_queues
This commit applies to igb_reset_task the same changes that
were applied to ixgbe in commit 2f90b8657e ("ixgbe: this patch
adds support for DCB to the kernel and ixgbe driver"),
commit 8f4c5c9fb8 ("ixgbe: reinit_locked() should be called with
rtnl_lock") and commit 88adce4ea8 ("ixgbe: fix possible race in
reset subtask").
Signed-off-by: Francesco Ruggeri <fruggeri@arista.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4052d3d2e8 ]
In the case where a vendor command does not implement doit, and has no
flags set, doit would not be validated and a NULL pointer dereference
would occur, for example when invoking the vendor command via iw.
I encountered this while developing new vendor commands. Perhaps in
practice it is advisable to always implement doit along with dumpit,
but it seems reasonable to me to always check doit anyway, not just
when NEED_WDEV.
Signed-off-by: Julian Squires <julian@cipht.net>
Link: https://lore.kernel.org/r/20200706211353.2366470-1-julian@cipht.net
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
