[ Upstream commit d176620277 ]
When VMX is used with flexpriority disabled (because of no support or
if disabled with module parameter) MMIO interface to lAPIC is still
available in x2APIC mode while it shouldn't be (kvm-unit-tests):
PASS: apic_disable: Local apic enabled in x2APIC mode
PASS: apic_disable: CPUID.1H:EDX.APIC[bit 9] is set
FAIL: apic_disable: *0xfee00030: 50014
The issue appears because we basically do nothing while switching to
x2APIC mode when APIC access page is not used. apic_mmio_{read,write}
only check if lAPIC is disabled before proceeding to actual write.
When APIC access is virtualized we correctly manipulate with VMX controls
in vmx_set_virtual_apic_mode() and we don't get vmexits from memory writes
in x2APIC mode so there's no issue.
Disabling MMIO interface seems to be easy. The question is: what do we
do with these reads and writes? If we add apic_x2apic_mode() check to
apic_mmio_in_range() and return -EOPNOTSUPP these reads and writes will
go to userspace. When lAPIC is in kernel, Qemu uses this interface to
inject MSIs only (see kvm_apic_mem_write() in hw/i386/kvm/apic.c). This
somehow works with disabled lAPIC but when we're in xAPIC mode we will
get a real injected MSI from every write to lAPIC. Not good.
The simplest solution seems to be to just ignore writes to the region
and return ~0 for all reads when we're in x2APIC mode. This is what this
patch does. However, this approach is inconsistent with what currently
happens when flexpriority is enabled: we allocate APIC access page and
create KVM memory region so in x2APIC modes all reads and writes go to
this pre-allocated page which is, btw, the same for all vCPUs.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 648e921888 ]
Commit d31fd43c0f ("clk: x86: Do not gate clocks enabled by the
firmware"), which added the code to mark clocks as CLK_IS_CRITICAL, causes
all unclaimed PMC clocks on Cherry Trail devices to be on all the time,
resulting on the device not being able to reach S0i3 when suspended.
The reason for this commit is that on some Bay Trail / Cherry Trail devices
the r8169 ethernet controller uses pmc_plt_clk_4. Now that the clk-pmc-atom
driver exports an "ether_clk" alias for pmc_plt_clk_4 and the r8169 driver
has been modified to get and enable this clock (if present) the marking of
the clocks as CLK_IS_CRITICAL is no longer necessary.
This commit removes the CLK_IS_CRITICAL marking, fixing Cherry Trail
devices not being able to reach S0i3 greatly decreasing their battery
drain when suspended.
Buglink: https://bugzilla.kernel.org/show_bug.cgi?id=193891#c102
Buglink: https://bugzilla.kernel.org/show_bug.cgi?id=196861
Cc: Johannes Stezenbach <js@sig21.net>
Cc: Carlo Caione <carlo@endlessm.com>
Reported-by: Johannes Stezenbach <js@sig21.net>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b1e3454d39 ]
Commit d31fd43c0f ("clk: x86: Do not gate clocks enabled by the
firmware") causes all unclaimed PMC clocks on Cherry Trail devices to be on
all the time, resulting on the device not being able to reach S0i2 or S0i3
when suspended.
The reason for this commit is that on some Bay Trail / Cherry Trail devices
the ethernet controller uses pmc_plt_clk_4. This commit adds an "ether_clk"
alias, so that the relevant ethernet drivers can try to (optionally) use
this, without needing X86 specific code / hacks, thus fixing ethernet on
these devices without breaking S0i3 support.
This commit uses clkdev_hw_create() to create the alias, mirroring the code
for the already existing "mclk" alias for pmc_plt_clk_3.
Buglink: https://bugzilla.kernel.org/show_bug.cgi?id=193891#c102
Buglink: https://bugzilla.kernel.org/show_bug.cgi?id=196861
Cc: Johannes Stezenbach <js@sig21.net>
Cc: Carlo Caione <carlo@endlessm.com>
Reported-by: Johannes Stezenbach <js@sig21.net>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a15f2c08c7 ]
The Hyper-V host API for PCI provides a unique "serial number" which
can be used as basis for sysfs PCI slot table. This can be useful
for cases where userspace wants to find the PCI device based on
serial number.
When an SR-IOV NIC is added, the host sends an attach message
with serial number. The kernel doesn't use the serial number, but
it is useful when doing the same thing in a userspace driver such
as the DPDK. By having /sys/bus/pci/slots/N it provides a direct
way to find the matching PCI device.
There maybe some cases where serial number is not unique such
as when using GPU's. But the PCI slot infrastructure will handle
that.
This has a side effect which may also be useful. The common udev
network device naming policy uses the slot information (rather
than PCI address).
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 321cc359d8 ]
We need this new compatibility string as we experienced different behavior
for this 10/100Mbits/s macb interface on this particular SoC.
Backward compatibility is preserved as we keep the alternative strings.
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit eb4ed8e2d7 ]
Create a new configuration for the sama5d3-macb new compatibility string.
This configuration disables scatter-gather because we experienced lock down
of the macb interface of this particular SoC under very high load.
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit edf2ef7242 ]
Synopsys DWC Ethernet MAC can be configured to have 1..32, 64, or
128 unicast filter entries. (Table 7-8 MAC Address Registers from
databook) Fix dwmac1000_validate_ucast_entries() to accept values
between 1 and 32 in addition.
Signed-off-by: Jongsung Kim <neidhard.kim@lge.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 75383f8d39 ]
Internally, skl_init_chip() calls snd_hdac_bus_init_chip() which
1) sets bus->chip_init to prevent multiple entrances before device
is stopped; 2) enables interrupt.
We shouldn't use it for the purpose of resetting device only because
1) when we really want to initialize device, we won't be able to do
so; 2) we are ready to handle interrupt yet, and kernel crashes when
interrupt comes in.
Rename azx_reset() to snd_hdac_bus_reset_link(), and use it to reset
device properly.
Fixes: 60767abcea ("ASoC: Intel: Skylake: Reset the controller in probe")
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Yu Zhao <yuzhao@google.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b61749a89f ]
In snd_hdac_bus_init_chip(), we enable interrupt before
snd_hdac_bus_init_cmd_io() initializing dma buffers. If irq has
been acquired and irq handler uses the dma buffer, kernel may crash
when interrupt comes in.
Fix the problem by postponing enabling irq after dma buffer
initialization. And warn once on null dma buffer pointer during the
initialization.
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Yu Zhao <yuzhao@google.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 679fcae46c ]
Fedora got a bug report of a crash with iSCSI:
kernel BUG at include/linux/scatterlist.h:143!
...
RIP: 0010:iscsit_do_crypto_hash_buf+0x154/0x180 [iscsi_target_mod]
...
Call Trace:
? iscsi_target_tx_thread+0x200/0x200 [iscsi_target_mod]
iscsit_get_rx_pdu+0x4cd/0xa90 [iscsi_target_mod]
? native_sched_clock+0x3e/0xa0
? iscsi_target_tx_thread+0x200/0x200 [iscsi_target_mod]
iscsi_target_rx_thread+0x81/0xf0 [iscsi_target_mod]
kthread+0x120/0x140
? kthread_create_worker_on_cpu+0x70/0x70
ret_from_fork+0x3a/0x50
This is a BUG_ON for using a stack buffer with a scatterlist. There
are two cases that trigger this bug. Switch to using a dynamically
allocated buffer for one case and do not assign a NULL buffer in
another case.
Signed-off-by: Laura Abbott <labbott@redhat.com>
Reviewed-by: Mike Christie <mchristi@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 10492ee8ed ]
It currently only works if the parent bus uses "simple-bus". We
currently try to probe children with non-existing compatible values.
And we're missing .probe.
I noticed this while testing devices configured to probe using ti-sysc
interconnect target module driver. For that we also may want to rebind
the driver, so let's remove __init and __exit.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e6a57d22f7 ]
The percpu_rw_semaphore is not currently freed, and this leads to
a crash when the stale rcu callback is invoked. DEBUG_OBJECTS
detects this.
ODEBUG: free active (active state 1) object type: rcu_head hint: (null)
------------[ cut here ]------------
WARNING: CPU: 1 PID: 2024 at debug_print_object+0xac/0xc8
PC is at debug_print_object+0xac/0xc8
LR is at debug_print_object+0xac/0xc8
Call trace:
[<ffffff80082e2c2c>] debug_print_object+0xac/0xc8
[<ffffff80082e40b0>] debug_check_no_obj_freed+0x1e8/0x228
[<ffffff8008191254>] kfree+0x1cc/0x250
[<ffffff80083cc03c>] hci_uart_tty_close+0x54/0x108
[<ffffff800832e118>] tty_ldisc_close.isra.1+0x40/0x58
[<ffffff800832e14c>] tty_ldisc_kill+0x1c/0x40
[<ffffff800832e3dc>] tty_ldisc_release+0x94/0x170
[<ffffff8008325554>] tty_release_struct+0x1c/0x58
[<ffffff8008326400>] tty_release+0x3b0/0x490
[<ffffff80081a3fe8>] __fput+0x88/0x1d0
[<ffffff80081a418c>] ____fput+0xc/0x18
[<ffffff80080c0624>] task_work_run+0x9c/0xc0
[<ffffff80080a9e24>] do_exit+0x24c/0x8a0
[<ffffff80080aa4e0>] do_group_exit+0x38/0xa0
[<ffffff80080aa558>] __wake_up_parent+0x0/0x28
[<ffffff8008082c00>] el0_svc_naked+0x34/0x38
---[ end trace bfe08cbd89098cdf ]---
Signed-off-by: Hermes Zhang <chenhuiz@axis.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 6c92d5a274 ]
Current rsnd driver will fallback to PIO mode if it can't get DMA
handler. But, DMA might return -EPROBE_DEFER when probe timing.
This driver always fallback to PIO mode especially from
commit ac6bbf0cdf ("iommu: Remove IOMMU_OF_DECLARE") because
of this reason.
The DMA driver will be probed later, but sound driver might be
probed as PIO mode in such case. This patch fixup this issue.
Then, -EPROBE_DEFER is not error. Thus, let's don't indicate error
message in such case.
And it needs to call rsnd_adg_remove() individually if probe failed,
because it registers clk which should be unregister.
Maybe PIO fallback feature itself is not needed,
but let's keep it so far.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 4d85af102a ]
add CONFIG_MEMORY_HOTREMOVE=y in config
without this config, /sys/devices/system/memory/memory*/removable
always return 0, I endup getting an early skip during test
Signed-off-by: Lei Yang <Lei.Yang@windriver.com>
Signed-off-by: Shuah Khan (Samsung OSG) <shuah@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2ab2ddd301 ]
Timer handlers do not imply rcu_read_lock(), so my recent fix
triggered a LOCKDEP warning when SYNACK is retransmit.
Lets add rcu_read_lock()/rcu_read_unlock() pairs around ireq->ireq_opt
usages instead of guessing what is done by callers, since it is
not worth the pain.
Get rid of ireq_opt_deref() helper since it hides the logic
without real benefit, since it is now a standard rcu_dereference().
Fixes: 1ad98e9d1b ("tcp/dccp: fix lockdep issue when SYN is backlogged")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1ad98e9d1b ]
In normal SYN processing, packets are handled without listener
lock and in RCU protected ingress path.
But syzkaller is known to be able to trick us and SYN
packets might be processed in process context, after being
queued into socket backlog.
In commit 06f877d613 ("tcp/dccp: fix other lockdep splats
accessing ireq_opt") I made a very stupid fix, that happened
to work mostly because of the regular path being RCU protected.
Really the thing protecting ireq->ireq_opt is RCU read lock,
and the pseudo request refcnt is not relevant.
This patch extends what I did in commit 449809a66c ("tcp/dccp:
block BH for SYN processing") by adding an extra rcu_read_{lock|unlock}
pair in the paths that might be taken when processing SYN from
socket backlog (thus possibly in process context)
Fixes: 06f877d613 ("tcp/dccp: fix other lockdep splats accessing ireq_opt")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 474ff26008 ]
So it should not fail with EPERM even though it is no longer implemented...
This is a fix for:
(userns)$ egrep ^Cap /proc/self/status
CapInh: 0000003fffffffff
CapPrm: 0000003fffffffff
CapEff: 0000003fffffffff
CapBnd: 0000003fffffffff
CapAmb: 0000003fffffffff
(userns)$ tcpdump -i usb_rndis0
tcpdump: WARNING: usb_rndis0: SIOCETHTOOL(ETHTOOL_GUFO) ioctl failed: Operation not permitted
Warning: Kernel filter failed: Bad file descriptor
tcpdump: can't remove kernel filter: Bad file descriptor
With this change it returns EOPNOTSUPP instead of EPERM.
See also https://github.com/the-tcpdump-group/libpcap/issues/689
Fixes: 08a00fea6d "net: Remove references to NETIF_F_UFO from ethtool."
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Maciej Żenczykowski <maze@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ff58e2df62 ]
When FW floods the driver with control messages try to exit the cmsg
processing loop every now and then to avoid soft lockups. Cmsg
processing is generally very lightweight so 512 seems like a reasonable
budget, which should not be exceeded under normal conditions.
Fixes: 77ece8d5f1 ("nfp: add control vNIC datapath")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Tested-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0f3b914c9c ]
RX queue config for bonding master could be different from its slave
device(s). With the commit 6a9e461f6f ("bonding: pass link-local
packets to bonding master also."), the packet is reinjected into stack
with skb->dev as bonding master. This potentially triggers the
message:
"bondX received packet on queue Y, but number of RX queues is Z"
whenever the queue that packet is received on is higher than the
numrxqueues on bonding master (Y > Z).
Fixes: 6a9e461f6f ("bonding: pass link-local packets to bonding master also.")
Reported-by: John Sperbeck <jsperbeck@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 6a9e461f6f ]
Commit b89f04c61e ("bonding: deliver link-local packets with
skb->dev set to link that packets arrived on") changed the behavior
of how link-local-multicast packets are processed. The change in
the behavior broke some legacy use cases where these packets are
expected to arrive on bonding master device also.
This patch passes the packet to the stack with the link it arrived
on as well as passes to the bonding-master device to preserve the
legacy use case.
Fixes: b89f04c61e ("bonding: deliver link-local packets with skb->dev set to link that packets arrived on")
Reported-by: Michal Soltys <soltys@ziu.info>
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 11aa5800ed ]
The code that deals with eswitch vport bw guarantee was going beyond the
eswitch vport array limit, fix that. This was pointed out by the kernel
address sanitizer (KASAN).
The error from KASAN log:
[2018-09-15 15:04:45] BUG: KASAN: slab-out-of-bounds in
mlx5_eswitch_set_vport_rate+0x8c1/0xae0 [mlx5_core]
Fixes: c9497c9890 ("net/mlx5: Add support for setting VF min rate")
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d26ed6b0e5 ]
This patch fixes skb_shared area, which will be corrupted
upon reception of 4K jumbo packets.
Originally build_skb usage purpose was to reuse page for skb to eliminate
needs of extra fragments. But that logic does not take into account that
skb_shared_info should be reserved at the end of skb data area.
In case packet data consumes all the page (4K), skb_shinfo location
overflows the page. As a consequence, __build_skb zeroed shinfo data above
the allocated page, corrupting next page.
The issue is rarely seen in real life because jumbo are normally larger
than 4K and that causes another code path to trigger.
But it 100% reproducible with simple scapy packet, like:
sendp(IP(dst="192.168.100.3") / TCP(dport=443) \
/ Raw(RandString(size=(4096-40))), iface="enp1s0")
Fixes: 018423e90b ("net: ethernet: aquantia: Add ring support code")
Reported-by: Friedemann Gerold <f.gerold@b-c-s.de>
Reported-by: Michael Rauch <michael@rauch.be>
Signed-off-by: Friedemann Gerold <f.gerold@b-c-s.de>
Tested-by: Nikita Danilov <nikita.danilov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit cee2648762 ]
In flow steering, if asked to, the hardware matches on the first ethertype
which is not vlan. It's possible to set a rule as follows, which is meant
to match on untagged packet, but will match on a vlan packet:
tc filter add dev eth0 parent ffff: protocol ip flower ...
To avoid this for packets with single tag, we set vlan masks to tell
hardware to check the tags for every matched packet.
Fixes: 095b6cfd69 ('net/mlx5e: Add TC vlan match parsing')
Signed-off-by: Jianbo Liu <jianbol@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit bf3b452b7a ]
The order in which we release resources is unfortunately leading to bus
errors while dismantling the port. This is because we set
priv->wol_ports_mask to 0 to tell bcm_sf2_sw_suspend() that it is now
permissible to clock gate the switch. Later on, when dsa_slave_destroy()
comes in from dsa_unregister_switch() and calls
dsa_switch_ops::port_disable, we perform the same dismantling again, and
this time we hit registers that are clock gated.
Make sure that dsa_unregister_switch() is the first thing that happens,
which takes care of releasing all user visible resources, then proceed
with clock gating hardware. We still need to set priv->wol_ports_mask to
0 to make sure that an enabled port properly gets disabled in case it
was previously used as part of Wake-on-LAN.
Fixes: d9338023fb ("net: dsa: bcm_sf2: Make it a real platform device driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9d2f67e43b ]
When we use raw socket as the vhost backend, a packet from virito with
gso offloading information, cannot be sent out in later validaton at
xmit path, as we did not set correct skb->protocol which is further used
for looking up the gso function.
To fix this, we set this field according to virito hdr information.
Fixes: e858fae2b0 ("virtio_net: use common code for virtio_net_hdr and skb GSO conversion")
Signed-off-by: Jianfeng Tan <jianfeng.tan@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0431100b3d ]
Currently we are always setting the tail address of descriptor list to
the end of the pre-allocated list.
According to databook this is not correct. Tail address should point to
the last available descriptor + 1, which means we have to update the
tail address everytime we call the xmit function.
This should make no impact in older versions of MAC but in newer
versions there are some DMA features which allows the IP to fetch
descriptors in advance and in a non sequential order so its critical
that we set the tail address correctly.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Fixes: f748be531d ("stmmac: support new GMAC4")
Cc: David S. Miller <davem@davemloft.net>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 7e823644b6 ]
Commit 2276f58ac5 ("udp: use a separate rx queue for packet reception")
turned static inline __skb_recv_udp() from being a trivial helper around
__skb_recv_datagram() into a UDP specific implementaion, making it
EXPORT_SYMBOL_GPL() at the same time.
There are external modules that got broken by __skb_recv_udp() not being
visible to them. Let's unbreak them by making __skb_recv_udp EXPORT_SYMBOL().
Rationale (one of those) why this is actually "technically correct" thing
to do: __skb_recv_udp() used to be an inline wrapper around
__skb_recv_datagram(), which itself (still, and correctly so, I believe)
is EXPORT_SYMBOL().
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: Eric Dumazet <edumazet@google.com>
Fixes: 2276f58ac5 ("udp: use a separate rx queue for packet reception")
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 92ef12b32f ]
In the case of implicit connect message with data > 1K, the flow
control accounting is incorrect. At this state, the socket does not
know the peer nodes capability and falls back to legacy flow control
by return 1, however the receiver of this message will perform the
new block accounting. This leads to a slack and eventually traffic
disturbance.
In this commit, we perform tipc_node_get_capabilities() at implicit
connect and perform accounting based on the peer's capability.
Signed-off-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d7ab5cdce5 ]
When processing pmtu update from an icmp packet, it calls .update_pmtu
with sk instead of skb in sctp_transport_update_pmtu.
However for sctp, the daddr in the transport might be different from
inet_sock->inet_daddr or sk->sk_v6_daddr, which is used to update or
create the route cache. The incorrect daddr will cause a different
route cache created for the path.
So before calling .update_pmtu, inet_sock->inet_daddr/sk->sk_v6_daddr
should be updated with the daddr in the transport, and update it back
after it's done.
The issue has existed since route exceptions introduction.
Fixes: 4895c771c7 ("ipv4: Add FIB nexthop exceptions.")
Reported-by: ian.periam@dialogic.com
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0e1d6eca51 ]
We have an impressive number of syzkaller bugs that are linked
to the fact that syzbot was able to create a networking device
with millions of TX (or RX) queues.
Let's limit the number of RX/TX queues to 4096, this really should
cover all known cases.
A separate patch will add various cond_resched() in the loops
handling sysfs entries at device creation and dismantle.
Tested:
lpaa6:~# ip link add gre-4097 numtxqueues 4097 numrxqueues 4097 type ip6gretap
RTNETLINK answers: Invalid argument
lpaa6:~# time ip link add gre-4096 numtxqueues 4096 numrxqueues 4096 type ip6gretap
real 0m0.180s
user 0m0.000s
sys 0m0.107s
Fixes: 76ff5cc919 ("rtnl: allow to specify number of rx and tx queues on device creation")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit bd961c9bc6 ]
Currently, rtnl_fdb_dump() assumes the family header is 'struct ifinfomsg',
which is not always true -- 'struct ndmsg' is used by iproute2 ('ip neigh').
The problem is, the function bails out early if nlmsg_parse() fails, which
does occur for iproute2 usage of 'struct ndmsg' because the payload length
is shorter than the family header alone (as 'struct ifinfomsg' is assumed).
This breaks backward compatibility with userspace -- nothing is sent back.
Some examples with iproute2 and netlink library for go [1]:
1) $ bridge fdb show
33:33:00:00:00:01 dev ens3 self permanent
01:00:5e:00:00:01 dev ens3 self permanent
33:33:ff:15:98:30 dev ens3 self permanent
This one works, as it uses 'struct ifinfomsg'.
fdb_show() @ iproute2/bridge/fdb.c
"""
.n.nlmsg_len = NLMSG_LENGTH(sizeof(struct ifinfomsg)),
...
if (rtnl_dump_request(&rth, RTM_GETNEIGH, [...]
"""
2) $ ip --family bridge neigh
RTNETLINK answers: Invalid argument
Dump terminated
This one fails, as it uses 'struct ndmsg'.
do_show_or_flush() @ iproute2/ip/ipneigh.c
"""
.n.nlmsg_type = RTM_GETNEIGH,
.n.nlmsg_len = NLMSG_LENGTH(sizeof(struct ndmsg)),
"""
3) $ ./neighlist
< no output >
This one fails, as it uses 'struct ndmsg'-based.
neighList() @ netlink/neigh_linux.go
"""
req := h.newNetlinkRequest(unix.RTM_GETNEIGH, [...]
msg := Ndmsg{
"""
The actual breakage was introduced by commit 0ff50e83b5 ("net: rtnetlink:
bail out from rtnl_fdb_dump() on parse error"), because nlmsg_parse() fails
if the payload length (with the _actual_ family header) is less than the
family header length alone (which is assumed, in parameter 'hdrlen').
This is true in the examples above with struct ndmsg, with size and payload
length shorter than struct ifinfomsg.
However, that commit just intends to fix something under the assumption the
family header is indeed an 'struct ifinfomsg' - by preventing access to the
payload as such (via 'ifm' pointer) if the payload length is not sufficient
to actually contain it.
The assumption was introduced by commit 5e6d243587 ("bridge: netlink dump
interface at par with brctl"), to support iproute2's 'bridge fdb' command
(not 'ip neigh') which indeed uses 'struct ifinfomsg', thus is not broken.
So, in order to unbreak the 'struct ndmsg' family headers and still allow
'struct ifinfomsg' to continue to work, check for the known message sizes
used with 'struct ndmsg' in iproute2 (with zero or one attribute which is
not used in this function anyway) then do not parse the data as ifinfomsg.
Same examples with this patch applied (or revert/before the original fix):
$ bridge fdb show
33:33:00:00:00:01 dev ens3 self permanent
01:00:5e:00:00:01 dev ens3 self permanent
33:33:ff:15:98:30 dev ens3 self permanent
$ ip --family bridge neigh
dev ens3 lladdr 33:33:00:00:00:01 PERMANENT
dev ens3 lladdr 01:00:5e:00:00:01 PERMANENT
dev ens3 lladdr 33:33:ff:15:98:30 PERMANENT
$ ./neighlist
netlink.Neigh{LinkIndex:2, Family:7, State:128, Type:0, Flags:2, IP:net.IP(nil), HardwareAddr:net.HardwareAddr{0x33, 0x33, 0x0, 0x0, 0x0, 0x1}, LLIPAddr:net.IP(nil), Vlan:0, VNI:0}
netlink.Neigh{LinkIndex:2, Family:7, State:128, Type:0, Flags:2, IP:net.IP(nil), HardwareAddr:net.HardwareAddr{0x1, 0x0, 0x5e, 0x0, 0x0, 0x1}, LLIPAddr:net.IP(nil), Vlan:0, VNI:0}
netlink.Neigh{LinkIndex:2, Family:7, State:128, Type:0, Flags:2, IP:net.IP(nil), HardwareAddr:net.HardwareAddr{0x33, 0x33, 0xff, 0x15, 0x98, 0x30}, LLIPAddr:net.IP(nil), Vlan:0, VNI:0}
Tested on mainline (v4.19-rc6) and net-next (3bd09b05b0).
References:
[1] netlink library for go (test-case)
https://github.com/vishvananda/netlink
$ cat ~/go/src/neighlist/main.go
package main
import ("fmt"; "syscall"; "github.com/vishvananda/netlink")
func main() {
neighs, _ := netlink.NeighList(0, syscall.AF_BRIDGE)
for _, neigh := range neighs { fmt.Printf("%#v\n", neigh) }
}
$ export GOPATH=~/go
$ go get github.com/vishvananda/netlink
$ go build neighlist
$ ~/go/src/neighlist/neighlist
Thanks to David Ahern for suggestions to improve this patch.
Fixes: 0ff50e83b5 ("net: rtnetlink: bail out from rtnl_fdb_dump() on parse error")
Fixes: 5e6d243587 ("bridge: netlink dump interface at par with brctl")
Reported-by: Aidan Obley <aobley@pivotal.io>
Signed-off-by: Mauricio Faria de Oliveira <mfo@canonical.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 4f7617705b ]
Added support for Gemalto's Cinterion ALASxx WWAN interfaces
by adding QMI_FIXED_INTF with Cinterion's VID and PID.
Signed-off-by: Giacinto Cifelli <gciofono@gmail.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c333fa0c4f ]
In regular NIC transmission flow, driver always configures MAC using
Tx queue zero descriptor as a part of MAC learning flow.
But with multi Tx queue supported NIC, regular transmission can occur on
any non-zero Tx queue and from that context it uses
Tx queue zero descriptor to configure MAC, at the same time TX queue
zero could be used by another CPU for regular transmission
which could lead to Tx queue zero descriptor corruption and cause FW
abort.
This patch fixes this in such a way that driver always configures
learned MAC address from the same Tx queue which is used for
regular transmission.
Fixes: 7e2cf4feba ("qlcnic: change driver hardware interface mechanism")
Signed-off-by: Shahed Shaikh <shahed.shaikh@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 45ec318578 ]
The AON_PM_L2 is normally used to trigger and identify the source of a
wake-up event. Since the RX_SYS clock is no longer turned off, we also
have an interrupt being sent to the SYSTEMPORT INTRL_2_0 controller, and
that interrupt remains active up until the magic packet detector is
disabled which happens much later during the driver resumption.
The race happens if we have a CPU that is entering the SYSTEMPORT
INTRL2_0 handler during resume, and another CPU has managed to clear the
wake-up interrupt during bcm_sysport_resume_from_wol(). In that case, we
have the first CPU stuck in the interrupt handler with an interrupt
cause that has been cleared under its feet, and so we keep returning
IRQ_NONE and we never make any progress.
This was not a problem before because we would always turn off the
RX_SYS clock during WoL, so the SYSTEMPORT INTRL2_0 would also be turned
off as well, thus not latching the interrupt.
The fix is to make sure we do not enable either the MPD or
BRCM_TAG_MATCH interrupts since those are redundant with what the
AON_PM_L2 interrupt controller already processes and they would cause
such a race to occur.
Fixes: bb9051a2b2 ("net: systemport: Add support for WAKE_FILTER")
Fixes: 83e82f4c70 ("net: systemport: add Wake-on-LAN support")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 8b4c3cdd9d ]
A number of TC attributes are processed without proper validation
(e.g., length checks). Add a tca policy for all input attributes and use
when invoking nlmsg_parse.
The 2 Fixes tags below cover the latest additions. The other attributes
are a string (KIND), nested attribute (OPTIONS which does seem to have
validation in most cases), for dumps only or a flag.
Fixes: 5bc1701881 ("net: sched: introduce multichain support for filters")
Fixes: d47a6b0e7c ("net: sched: introduce ingress/egress block index attributes for qdisc")
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 774268f3e5 ]
When no Tx IRQ is available, the txq_done() routine (called from
tx_done()) shouldn't be called from the polling function, as in such
case it is already called in the Tx path thanks to an hrtimer. This
mostly occurred when using PPv2.1, as the engine then do not have Tx
IRQs.
Fixes: edc660fa09 ("net: mvpp2: replace TX coalescing interrupts with hrtimer")
Reported-by: Stefan Chulski <stefanc@marvell.com>
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 35f3625c21 ]
When offloading the L3 and L4 csum computation on TX, we need to extract
the l3_proto from the ethtype, independently of the presence of a vlan
tag.
The actual driver uses skb->protocol as-is, resulting in packets with
the wrong L4 checksum being sent when there's a vlan tag in the packet
header and checksum offloading is enabled.
This commit makes use of vlan_protocol_get() to get the correct ethtype
regardless the presence of a vlan tag.
Fixes: 3f518509de ("ethernet: Add new driver for Marvell Armada 375 network unit")
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f88b4c01b9 ]
netlbl_unlabel_addrinfo_get() assumes that if it finds the
NLBL_UNLABEL_A_IPV4ADDR attribute, it must also have the
NLBL_UNLABEL_A_IPV4MASK attribute as well. However, this is
not necessarily the case as the current checks in
netlbl_unlabel_staticadd() and friends are not sufficent to
enforce this.
If passed a netlink message with NLBL_UNLABEL_A_IPV4ADDR,
NLBL_UNLABEL_A_IPV6ADDR, and NLBL_UNLABEL_A_IPV6MASK attributes,
these functions will all call netlbl_unlabel_addrinfo_get() which
will then attempt dereference NULL when fetching the non-existent
NLBL_UNLABEL_A_IPV4MASK attribute:
Unable to handle kernel NULL pointer dereference at virtual address 0
Process unlab (pid: 31762, stack limit = 0xffffff80502d8000)
Call trace:
netlbl_unlabel_addrinfo_get+0x44/0xd8
netlbl_unlabel_staticremovedef+0x98/0xe0
genl_rcv_msg+0x354/0x388
netlink_rcv_skb+0xac/0x118
genl_rcv+0x34/0x48
netlink_unicast+0x158/0x1f0
netlink_sendmsg+0x32c/0x338
sock_sendmsg+0x44/0x60
___sys_sendmsg+0x1d0/0x2a8
__sys_sendmsg+0x64/0xb4
SyS_sendmsg+0x34/0x4c
el0_svc_naked+0x34/0x38
Code: 51001149 7100113f 540000a0 f9401508 (79400108)
---[ end trace f6438a488e737143 ]---
Kernel panic - not syncing: Fatal exception
Signed-off-by: Sean Tranchetti <stranche@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
