[ Upstream commit ad9001f2f4 ]
Currently Linux does not follow PCIe spec regarding the required delays
after reset. A concrete example is a Thunderbolt add-in-card that consists
of a PCIe switch and two PCIe endpoints:
+-1b.0-[01-6b]----00.0-[02-6b]--+-00.0-[03]----00.0 TBT controller
+-01.0-[04-36]-- DS hotplug port
+-02.0-[37]----00.0 xHCI controller
\-04.0-[38-6b]-- DS hotplug port
The root port (1b.0) and the PCIe switch downstream ports are all PCIe Gen3
so they support 8GT/s link speeds.
We wait for the PCIe hierarchy to enter D3cold (runtime):
pcieport 0000:00:1b.0: power state changed by ACPI to D3cold
When it wakes up from D3cold, according to the PCIe 5.0 section 5.8 the
PCIe switch is put to reset and its power is re-applied. This means that we
must follow the rules in PCIe 5.0 section 6.6.1.
For the PCIe Gen3 ports we are dealing with here, the following applies:
With a Downstream Port that supports Link speeds greater than 5.0 GT/s,
software must wait a minimum of 100 ms after Link training completes
before sending a Configuration Request to the device immediately below
that Port. Software can determine when Link training completes by polling
the Data Link Layer Link Active bit or by setting up an associated
interrupt (see Section 6.7.3.3).
Translating this into the above topology we would need to do this (DLLLA
stands for Data Link Layer Link Active):
0000:00:1b.0: wait for 100 ms after DLLLA is set before access to 0000:01:00.0
0000:02:00.0: wait for 100 ms after DLLLA is set before access to 0000:03:00.0
0000:02:02.0: wait for 100 ms after DLLLA is set before access to 0000:37:00.0
I've instrumented the kernel with some additional logging so we can see the
actual delays performed:
pcieport 0000:00:1b.0: power state changed by ACPI to D0
pcieport 0000:00:1b.0: waiting for D3cold delay of 100 ms
pcieport 0000:00:1b.0: waiting for D3hot delay of 10 ms
pcieport 0000:02:01.0: waiting for D3hot delay of 10 ms
pcieport 0000:02:04.0: waiting for D3hot delay of 10 ms
For the switch upstream port (01:00.0 reachable through 00:1b.0 root port)
we wait for 100 ms but not taking into account the DLLLA requirement. We
then wait 10 ms for D3hot -> D0 transition of the root port and the two
downstream hotplug ports. This means that we deviate from what the spec
requires.
Performing the same check for system sleep (s2idle) transitions it turns
out to be even worse. None of the mandatory delays are performed. If this
would be S3 instead of s2idle then according to PCI FW spec 3.2 section
4.6.8. there is a specific _DSM that allows the OS to skip the delays but
this platform does not provide the _DSM and does not go to S3 anyway so no
firmware is involved that could already handle these delays.
On this particular platform these delays are not actually needed because
there is an additional delay as part of the ACPI power resource that is
used to turn on power to the hierarchy but since that additional delay is
not required by any of standards (PCIe, ACPI) it is not present in the
Intel Ice Lake, for example where missing the mandatory delays causes
pciehp to start tearing down the stack too early (links are not yet
trained). Below is an example how it looks like when this happens:
pcieport 0000:83:04.0: pciehp: Slot(4): Card not present
pcieport 0000:87:04.0: PME# disabled
pcieport 0000:83:04.0: pciehp: pciehp_unconfigure_device: domain:bus:dev = 0000:86:00
pcieport 0000:86:00.0: Refused to change power state, currently in D3
pcieport 0000:86:00.0: restoring config space at offset 0x3c (was 0xffffffff, writing 0x201ff)
pcieport 0000:86:00.0: restoring config space at offset 0x38 (was 0xffffffff, writing 0x0)
...
There is also one reported case (see the bugzilla link below) where the
missing delay causes xHCI on a Titan Ridge controller fail to runtime
resume when USB-C dock is plugged. This does not involve pciehp but instead
the PCI core fails to runtime resume the xHCI device:
pcieport 0000:04:02.0: restoring config space at offset 0xc (was 0x10000, writing 0x10020)
pcieport 0000:04:02.0: restoring config space at offset 0x4 (was 0x100000, writing 0x100406)
xhci_hcd 0000:39:00.0: Refused to change power state, currently in D3
xhci_hcd 0000:39:00.0: restoring config space at offset 0x3c (was 0xffffffff, writing 0x1ff)
xhci_hcd 0000:39:00.0: restoring config space at offset 0x38 (was 0xffffffff, writing 0x0)
...
Add a new function pci_bridge_wait_for_secondary_bus() that is called on
PCI core resume and runtime resume paths accordingly if the bridge entered
D3cold (and thus went through reset).
This is second attempt to add the missing delays. The previous solution in
c2bf1fc212 ("PCI: Add missing link delays required by the PCIe spec") was
reverted because of two issues it caused:
1. One system become unresponsive after S3 resume due to PME service
spinning in pcie_pme_work_fn(). The root port in question reports that
the xHCI sent PME but the xHCI device itself does not have PME status
set. The PME status bit is never cleared in the root port resulting
the indefinite loop in pcie_pme_work_fn().
2. Slows down resume if the root/downstream port does not support Data
Link Layer Active Reporting because pcie_wait_for_link_delay() waits
1100 ms in that case.
This version should avoid the above issues because we restrict the delay to
happen only if the port went into D3cold.
Link: https://lore.kernel.org/linux-pci/SL2P216MB01878BBCD75F21D882AEEA2880C60@SL2P216MB0187.KORP216.PROD.OUTLOOK.COM/
Link: https://bugzilla.kernel.org/show_bug.cgi?id=203885
Link: https://lore.kernel.org/r/20191112091617.70282-3-mika.westerberg@linux.intel.com
Reported-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Tested-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 87d0f2a553 ]
This addresses deadlocks in these common cases in hierarchies containing
two switches:
- All involved ports are runtime suspended and they are unplugged. This
can happen easily if the drivers involved automatically enable runtime
PM (xHCI for example does that).
- System is suspended (e.g., closing the lid on a laptop) with a dock +
something else connected, and the dock is unplugged while suspended.
These cases lead to the following deadlock:
INFO: task irq/126-pciehp:198 blocked for more than 120 seconds.
irq/126-pciehp D 0 198 2 0x80000000
Call Trace:
schedule+0x2c/0x80
schedule_timeout+0x246/0x350
wait_for_completion+0xb7/0x140
kthread_stop+0x49/0x110
free_irq+0x32/0x70
pcie_shutdown_notification+0x2f/0x50
pciehp_remove+0x27/0x50
pcie_port_remove_service+0x36/0x50
device_release_driver+0x12/0x20
bus_remove_device+0xec/0x160
device_del+0x13b/0x350
device_unregister+0x1a/0x60
remove_iter+0x1e/0x30
device_for_each_child+0x56/0x90
pcie_port_device_remove+0x22/0x40
pcie_portdrv_remove+0x20/0x60
pci_device_remove+0x3e/0xc0
device_release_driver_internal+0x18c/0x250
device_release_driver+0x12/0x20
pci_stop_bus_device+0x6f/0x90
pci_stop_bus_device+0x31/0x90
pci_stop_and_remove_bus_device+0x12/0x20
pciehp_unconfigure_device+0x88/0x140
pciehp_disable_slot+0x6a/0x110
pciehp_handle_presence_or_link_change+0x263/0x400
pciehp_ist+0x1c9/0x1d0
irq_thread_fn+0x24/0x60
irq_thread+0xeb/0x190
kthread+0x120/0x140
INFO: task irq/190-pciehp:2288 blocked for more than 120 seconds.
irq/190-pciehp D 0 2288 2 0x80000000
Call Trace:
__schedule+0x2a2/0x880
schedule+0x2c/0x80
schedule_preempt_disabled+0xe/0x10
mutex_lock+0x2c/0x30
pci_lock_rescan_remove+0x15/0x20
pciehp_unconfigure_device+0x4d/0x140
pciehp_disable_slot+0x6a/0x110
pciehp_handle_presence_or_link_change+0x263/0x400
pciehp_ist+0x1c9/0x1d0
irq_thread_fn+0x24/0x60
irq_thread+0xeb/0x190
kthread+0x120/0x140
What happens here is that the whole hierarchy is runtime resumed and the
parent PCIe downstream port, which got the hot-remove event, starts
removing devices below it, taking pci_lock_rescan_remove() lock. When the
child PCIe port is runtime resumed it calls pciehp_check_presence() which
ends up calling pciehp_card_present() and pciehp_check_link_active(). Both
of these use pcie_capability_read_word(), which notices that the underlying
device is already gone and returns PCIBIOS_DEVICE_NOT_FOUND with the
capability value set to 0. When pciehp gets this value it thinks that its
child device is also hot-removed and schedules its IRQ thread to handle the
event.
The deadlock happens when the child's IRQ thread runs and tries to acquire
pci_lock_rescan_remove() which is already taken by the parent and the
parent waits for the child's IRQ thread to finish.
Prevent this from happening by checking the return value of
pcie_capability_read_word() and if it is PCIBIOS_DEVICE_NOT_FOUND stop
performing any hot-removal activities.
[bhelgaas: add common scenarios to commit log]
Link: https://lore.kernel.org/r/20191029170022.57528-2-mika.westerberg@linux.intel.com
Tested-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3464afdf11 ]
On powerpc with recent versions of binutils, readelf outputs an extra
field when dumping the symbols of an object file. For example:
35: 0000000000000838 96 FUNC LOCAL DEFAULT [<localentry>: 8] 1 btf_is_struct
The extra "[<localentry>: 8]" prevents the GLOBAL_SYM_COUNT variable to
be computed correctly and causes the check_abi target to fail.
Fix that by looking for the symbol name in the last field instead of the
8th one. This way it should also cope with future extra fields.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Tested-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/bpf/20191201195728.4161537-1-aurelien@aurel32.net
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9941b81290 ]
[Why]
In some scenario like 1366x768 VSR enabled connected with a 4K monitor
and playing 4K video in clone mode, underflow will be observed due to
decrease dppclk when previouse surface scan isn't finished
[How]
In this use case, surface flip is switching between 4K and 1366x768,
1366x768 needs smaller dppclk, and when decrease the clk and previous
surface scan is for 4K and scan isn't done, underflow will happen. Not
doing optimize bandwidth in case of flip pending.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ceca49382a ]
Depending on the current link state the steps to resume the link to U0
varies. The normal case when a port is suspended (U3) we set the link
to U0 and wait for a port event when U3exit completed and port moved to
U0.
If the port is in U1/U2, then no event is issued, just set link to U0
If port is in Resume or Recovery state then the device has already
initiated resume, and this host initiated resume is racing against it.
Port event handler for device initiated resume will set link to U0,
just wait for the port to reach U0 before returning.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200312144517.1593-9-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit eb002726fa ]
The xHCI spec doesn't specify the upper bound of U3 transition time. For
some devices 20ms is not enough, so we need to make sure the link state
is in U3 before further actions.
I've tried to use U3 Entry Capability by setting U3 Entry Enable in
config register, however the port change event for U3 transition
interrupts the system suspend process.
For now let's use the less ideal method by polling PLS.
[use usleep_range(), and shorten the delay time while polling -Mathias]
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200312144517.1593-7-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3bae20137c ]
[Why]
If a plane isn't being actively enabled or disabled then DC won't
always recalculate scaling rects and ratios for the primary plane.
This results in only a partial or corrupted rect being displayed on
the screen instead of scaling to fit the screen.
[How]
Add back the logic to recalculate the scaling rects into
dc_commit_updates_for_stream since this is the expected place to
do it in DC.
This was previously removed a few years ago to fix an underscan issue
but underscan is still functional now with this change - and it should
be, since this is only updating to the latest plane state getting passed
in.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d3296fb372 ]
We hit following warning when running tests on kernel
compiled with CONFIG_DEBUG_ATOMIC_SLEEP=y:
WARNING: CPU: 19 PID: 4472 at mm/gup.c:2381 __get_user_pages_fast+0x1a4/0x200
CPU: 19 PID: 4472 Comm: dummy Not tainted 5.6.0-rc6+ #3
RIP: 0010:__get_user_pages_fast+0x1a4/0x200
...
Call Trace:
perf_prepare_sample+0xff1/0x1d90
perf_event_output_forward+0xe8/0x210
__perf_event_overflow+0x11a/0x310
__intel_pmu_pebs_event+0x657/0x850
intel_pmu_drain_pebs_nhm+0x7de/0x11d0
handle_pmi_common+0x1b2/0x650
intel_pmu_handle_irq+0x17b/0x370
perf_event_nmi_handler+0x40/0x60
nmi_handle+0x192/0x590
default_do_nmi+0x6d/0x150
do_nmi+0x2f9/0x3c0
nmi+0x8e/0xd7
While __get_user_pages_fast() is IRQ-safe, it calls access_ok(),
which warns on:
WARN_ON_ONCE(!in_task() && !pagefault_disabled())
Peter suggested disabling page faults around __get_user_pages_fast(),
which gets rid of the warning in access_ok() call.
Suggested-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lkml.kernel.org/r/20200407141427.3184722-1-jolsa@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2c25b07e5e ]
The newer 2711 and 7211 chips have two PWM controllers and failure to
dynamically allocate the PWM base would prevent the second PWM
controller instance being probed for succeeding with an -EEXIST error
from alloc_pwms().
Fixes: e5a06dc5ac ("pwm: Add BCM2835 PWM driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d5a3c7a453 ]
Runtime PM should be enabled before calling pwmchip_add(), as PWM users
can appear immediately after the PWM chip has been added.
Likewise, Runtime PM should always be disabled after the removal of the
PWM chip, even if the latter failed.
Fixes: 99b82abb0a ("pwm: Add Renesas TPU PWM driver")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c95b708d5f ]
On a 32-bit kernel, the upper bits of userspace addresses passed via
various ioctls are silently ignored by the nvme driver.
However on a 64-bit kernel running a compat task, these upper bits are
not ignored and are in fact required to be zero for the ioctls to work.
Unfortunately, this difference matters. 32-bit smartctl submits the
NVME_IOCTL_ADMIN_CMD ioctl with garbage in these upper bits because it
seems the pointer value it puts into the nvme_passthru_cmd structure is
sign extended. This works fine on 32-bit kernels but fails on a 64-bit
one because (at least on my setup) the addresses smartctl uses are
consistently above 2G. For example:
# smartctl -x /dev/nvme0n1
smartctl 7.1 2019-12-30 r5022 [x86_64-linux-5.5.11] (local build)
Copyright (C) 2002-19, Bruce Allen, Christian Franke, www.smartmontools.org
Read NVMe Identify Controller failed: NVME_IOCTL_ADMIN_CMD: Bad address
Since changing 32-bit kernels to actually check all of the submitted
address bits now would break existing userspace, this patch fixes the
compat problem by explicitly zeroing the upper bits in the compat case.
This enables 32-bit smartctl to work on a 64-bit kernel.
Signed-off-by: Nick Bowler <nbowler@draconx.ca>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a95a0a1654 ]
MCE handling on pSeries platform fails as recent rework to use common
code for pSeries and PowerNV in machine check error handling tries to
access per-cpu variables in realmode. The per-cpu variables may be
outside the RMO region on pSeries platform and needs translation to be
enabled for access. Just moving these per-cpu variable into RMO region
did'nt help because we queue some work to workqueues in real mode, which
again tries to touch per-cpu variables. Also fwnmi_release_errinfo()
cannot be called when translation is not enabled.
This patch fixes this by enabling translation in the exception handler
when all required real mode handling is done. This change only affects
the pSeries platform.
Without this fix below kernel crash is seen on injecting
SLB multihit:
BUG: Unable to handle kernel data access on read at 0xc00000027b205950
Faulting instruction address: 0xc00000000003b7e0
Oops: Kernel access of bad area, sig: 11 [#1]
LE PAGE_SIZE=64K MMU=Hash SMP NR_CPUS=2048 NUMA pSeries
Modules linked in: mcetest_slb(OE+) af_packet(E) xt_tcpudp(E) ip6t_rpfilter(E) ip6t_REJECT(E) ipt_REJECT(E) xt_conntrack(E) ip_set(E) nfnetlink(E) ebtable_nat(E) ebtable_broute(E) ip6table_nat(E) ip6table_mangle(E) ip6table_raw(E) ip6table_security(E) iptable_nat(E) nf_nat(E) nf_conntrack(E) nf_defrag_ipv6(E) nf_defrag_ipv4(E) iptable_mangle(E) iptable_raw(E) iptable_security(E) ebtable_filter(E) ebtables(E) ip6table_filter(E) ip6_tables(E) iptable_filter(E) ip_tables(E) x_tables(E) xfs(E) ibmveth(E) vmx_crypto(E) gf128mul(E) uio_pdrv_genirq(E) uio(E) crct10dif_vpmsum(E) rtc_generic(E) btrfs(E) libcrc32c(E) xor(E) zstd_decompress(E) zstd_compress(E) raid6_pq(E) sr_mod(E) sd_mod(E) cdrom(E) ibmvscsi(E) scsi_transport_srp(E) crc32c_vpmsum(E) dm_mod(E) sg(E) scsi_mod(E)
CPU: 34 PID: 8154 Comm: insmod Kdump: loaded Tainted: G OE 5.5.0-mahesh #1
NIP: c00000000003b7e0 LR: c0000000000f2218 CTR: 0000000000000000
REGS: c000000007dcb960 TRAP: 0300 Tainted: G OE (5.5.0-mahesh)
MSR: 8000000000001003 <SF,ME,RI,LE> CR: 28002428 XER: 20040000
CFAR: c0000000000f2214 DAR: c00000027b205950 DSISR: 40000000 IRQMASK: 0
GPR00: c0000000000f2218 c000000007dcbbf0 c000000001544800 c000000007dcbd70
GPR04: 0000000000000001 c000000007dcbc98 c008000000d00258 c0080000011c0000
GPR08: 0000000000000000 0000000300000003 c000000001035950 0000000003000048
GPR12: 000000027a1d0000 c000000007f9c000 0000000000000558 0000000000000000
GPR16: 0000000000000540 c008000001110000 c008000001110540 0000000000000000
GPR20: c00000000022af10 c00000025480fd70 c008000001280000 c00000004bfbb300
GPR24: c000000001442330 c00800000800000d c008000008000000 4009287a77000510
GPR28: 0000000000000000 0000000000000002 c000000001033d30 0000000000000001
NIP [c00000000003b7e0] save_mce_event+0x30/0x240
LR [c0000000000f2218] pseries_machine_check_realmode+0x2c8/0x4f0
Call Trace:
Instruction dump:
3c4c0151 38429050 7c0802a6 60000000 fbc1fff0 fbe1fff8 f821ffd1 3d42ffaf
3fc2ffaf e98d0030 394a1150 3bdef530 <7d6a62aa> 1d2b0048 2f8b0063 380b0001
---[ end trace 46fd63f36bbdd940 ]---
Fixes: 9ca766f989 ("powerpc/64s/pseries: machine check convert to use common event code")
Reviewed-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Ganesh Goudar <ganeshgr@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200320110119.10207-1-ganeshgr@linux.ibm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit abc3fce76a ]
This reverts commit ebb37cf3ff.
That commit does not play well with soft-masked irq state
manipulations in idle, interrupt replay, and possibly others due to
tracing code sometimes using irq_work_queue (e.g., in
trace_hardirqs_on()). That can cause PACA_IRQ_DEC to become set when
it is not expected, and be ignored or cleared or cause warnings.
The net result seems to be missing an irq_work until the next timer
interrupt in the worst case which is usually not going to be noticed,
however it could be a long time if the tick is disabled, which is
against the spirit of irq_work and might cause real problems.
The idea is still solid, but it would need more work. It's not really
clear if it would be worth added complexity, so revert this for
now (not a straight revert, but replace with a comment explaining why
we might see interrupts happening, and gives git blame something to
find).
Fixes: ebb37cf3ff ("powerpc/64: irq_work avoid interrupt when called with hardware irqs enabled")
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200402120401.1115883-1-npiggin@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c52abf5630 ]
If the backing device for a loop device is itself a block device,
then mirror the "write zeroes" capabilities of the underlying
block device into the loop device. Copy this capability into both
max_write_zeroes_sectors and max_discard_sectors of the loop device.
The reason for this is that REQ_OP_DISCARD on a loop device translates
into blkdev_issue_zeroout(), rather than blkdev_issue_discard(). This
presents a consistent interface for loop devices (that discarded data
is zeroed), regardless of the backing device type of the loop device.
There should be no behavior change for loop devices backed by regular
files.
This change fixes blktest block/003, and removes an extraneous
error print in block/013 when testing on a loop device backed
by a block device that does not support discard.
Signed-off-by: Evan Green <evgreen@chromium.org>
Reviewed-by: Gwendal Grignou <gwendal@chromium.org>
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
[used updated version of Evan's comment in loop_config_discard()]
[moved backingq to local scope, removed redundant braces]
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@collabora.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 05ce3e53f3 ]
The common I/O layer delays the ADD uevent for subchannels and
delegates generating this uevent to the individual subchannel
drivers. The io_subchannel driver will do so when the associated
ccw_device has been registered -- but unconditionally, so more
ADD uevents will be generated if a subchannel has been unbound
from the io_subchannel driver and later rebound.
To fix this, only generate the ADD event if uevents were still
suppressed for the device.
Fixes: fa1a8c23eb ("s390: cio: Delay uevents for subchannels")
Message-Id: <20200327124503.9794-2-cohuck@redhat.com>
Reported-by: Boris Fiuczynski <fiuczy@linux.ibm.com>
Reviewed-by: Peter Oberparleiter <oberpar@linux.ibm.com>
Reviewed-by: Boris Fiuczynski <fiuczy@linux.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2bc55eaeb8 ]
The common I/O layer delays the ADD uevent for subchannels and
delegates generating this uevent to the individual subchannel
drivers. The vfio-ccw I/O subchannel driver, however, did not
do that, and will not generate an ADD uevent for subchannels
that had not been bound to a different driver (or none at all,
which also triggers the uevent).
Generate the ADD uevent at the end of the probe function if
uevents were still suppressed for the device.
Message-Id: <20200327124503.9794-3-cohuck@redhat.com>
Fixes: 63f1934d56 ("vfio: ccw: basic implementation for vfio_ccw driver")
Reviewed-by: Eric Farman <farman@linux.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 06bd48b6cd ]
You can build a user-space test program for the raid6 library code,
like this:
$ cd lib/raid6/test
$ make
The command in $(shell ...) function is evaluated by /bin/sh by default.
(or, you can specify the shell by passing SHELL=<shell> from command line)
Currently '>&/dev/null' is used to sink both stdout and stderr. Because
this code is bash-ism, it only works when /bin/sh is a symbolic link to
bash (this is the case on RHEL etc.)
This does not work on Ubuntu where /bin/sh is a symbolic link to dash.
I see lots of
/bin/sh: 1: Syntax error: Bad fd number
and
warning "your version of binutils lacks ... support"
Replace it with portable '>/dev/null 2>&1'.
Fixes: 4f8c55c5ad ("lib/raid6: build proper files on corresponding arch")
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Acked-by: H. Peter Anvin (Intel) <hpa@zytor.com>
Reviewed-by: Jason A. Donenfeld <Jason@zx2c4.com>
Acked-by: Ingo Molnar <mingo@kernel.org>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cdcda0d1f8 ]
The upper 32-bit physical address gets truncated inadvertently
when dma_direct_get_required_mask() invokes phys_to_dma_direct().
This results in dma_addressing_limited() return incorrect value
when used in platforms with LPAE enabled.
Fix it here by explicitly type casting 'max_pfn' to phys_addr_t
in order to prevent overflow of intermediate value while evaluating
'(max_pfn - 1) << PAGE_SHIFT'.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 346d8a0a3c ]
[Why]
After v_total_min and max are updated in vrr structure, the changes are
not reflected in stream adjust. When these values are read from stream
adjust it does not reflect the actual state of the system.
[How]
Set stream adjust values equal to vrr adjust values after vrr adjust
values are updated.
Signed-off-by: Isabel Zhang <isabel.zhang@amd.com>
Reviewed-by: Alvin Lee <Alvin.Lee2@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 657f1975e9 ]
The deadlock combines 4 flows in parallel:
- ns scanning (triggered from reconnect)
- request timeout
- ANA update (triggered from reconnect)
- I/O coming into the mpath device
(1) ns scanning triggers disk revalidation -> update disk info ->
freeze queue -> but blocked, due to (2)
(2) timeout handler reference the g_usage_counter - > but blocks in
the transport .timeout() handler, due to (3)
(3) the transport timeout handler (indirectly) calls nvme_stop_queue() ->
which takes the (down_read) namespaces_rwsem - > but blocks, due to (4)
(4) ANA update takes the (down_write) namespaces_rwsem -> calls
nvme_mpath_set_live() -> which synchronize the ns_head srcu
(see commit 504db087aa) -> but blocks, due to (5)
(5) I/O came into nvme_mpath_make_request -> took srcu_read_lock ->
direct_make_request > blk_queue_enter -> but blocked, due to (1)
==> the request queue is under freeze -> deadlock.
The fix is making ANA update take a read lock as the namespaces list
is not manipulated, it is just the ns and ns->head that are being
updated (which is protected with the ns->head lock).
Fixes: 0d0b660f21 ("nvme: add ANA support")
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1f77679962 ]
Out of tree build using
make M=tools/test/nvdimm O=/tmp/build -C /tmp/build
fails with the following error
make: Entering directory '/tmp/build'
CC [M] tools/testing/nvdimm/test/nfit.o
linux/tools/testing/nvdimm/test/nfit.c:19:10: fatal error: nd-core.h: No such file or directory
19 | #include <nd-core.h>
| ^~~~~~~~~~~
compilation terminated.
That is because the kbuild file uses $(src) which points to
tools/testing/nvdimm, $(srctree) correctly points to root of the linux
source tree.
Reported-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Signed-off-by: Santosh Sivaraj <santosh@fossix.org>
Link: https://lore.kernel.org/r/20200114054051.4115790-1-santosh@fossix.org
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 13e60d3ba2 ]
If the daemon is restarted or crashes while logging out of a session, the
unbind session event sent by the kernel is not processed and is lost. When
the daemon starts again, the session can't be unbound because the daemon is
waiting for the event message. However, the kernel has already logged out
and the event will not be resent.
When iscsid restart is complete, logout session reports error:
Logging out of session [sid: 6, target: iqn.xxxxx, portal: xx.xx.xx.xx,3260]
iscsiadm: Could not logout of [sid: 6, target: iscsiadm -m node iqn.xxxxx, portal: xx.xx.xx.xx,3260].
iscsiadm: initiator reported error (9 - internal error)
iscsiadm: Could not logout of all requested sessions
Make sure the unbind event is emitted.
[mkp: commit desc and applied by hand since patch was mangled]
Link: https://lore.kernel.org/r/4eab1771-2cb3-8e79-b31c-923652340e99@huawei.com
Reviewed-by: Lee Duncan <lduncan@suse.com>
Signed-off-by: Wu Bo <wubo40@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 25e5cb780e ]
We cannot look at blk_rq_payload_bytes without first checking
that the request has a mappable physical segments first (e.g.
blk_rq_nr_phys_segments(rq) != 0) and only then to take the
request payload bytes. This caused us to send a wrong sgl to
the target or even dereference a non-existing buffer in case
we actually got to the data send sequence (if it was in-capsule).
Reported-by: Tony Asleson <tasleson@redhat.com>
Suggested-by: Chaitanya Kulkarni <Chaitanya.Kulkarni@wdc.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0aa971b6fd ]
1. try_get_cap_refs() fails to get caps and finds that mds_wanted
does not include what it wants. It returns -ESTALE.
2. ceph_get_caps() calls ceph_renew_caps(). ceph_renew_caps() finds
that inode has cap, so it calls ceph_check_caps().
3. ceph_check_caps() finds that issued caps (without checking if it's
stale) already includes caps wanted by open file, so it skips
updating wanted caps.
Above events can cause an infinite loop inside ceph_get_caps().
Signed-off-by: "Yan, Zheng" <zyan@redhat.com>
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c6d5029603 ]
Return the error returned by ceph_mdsc_do_request(). Otherwise,
r_target_inode ends up being NULL this ends up returning ENOENT
regardless of the error.
Signed-off-by: Qiujun Huang <hqjagain@gmail.com>
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 807e7353d8 ]
Kernel is crashing with the following stacktrace:
BUG: unable to handle kernel NULL pointer dereference at
00000000000005bc
IP: lpfc_nvme_register_port+0x1a8/0x3a0 [lpfc]
...
Call Trace:
lpfc_nlp_state_cleanup+0x2b2/0x500 [lpfc]
lpfc_nlp_set_state+0xd7/0x1a0 [lpfc]
lpfc_cmpl_prli_prli_issue+0x1f7/0x450 [lpfc]
lpfc_disc_state_machine+0x7a/0x1e0 [lpfc]
lpfc_cmpl_els_prli+0x16f/0x1e0 [lpfc]
lpfc_sli_sp_handle_rspiocb+0x5b2/0x690 [lpfc]
lpfc_sli_handle_slow_ring_event_s4+0x182/0x230 [lpfc]
lpfc_do_work+0x87f/0x1570 [lpfc]
kthread+0x10d/0x130
ret_from_fork+0x35/0x40
During target side fault injections, it is possible to hit the
NLP_WAIT_FOR_UNREG case in lpfc_nvme_remoteport_delete. A prior commit
fixed a rebind and delete race condition, but called lpfc_nlp_put
unconditionally. This triggered a deletion and the crash.
Fix by movng nlp_put to inside the NLP_WAIT_FOR_UNREG case, where the nlp
will be being unregistered/removed. Leave the reference if the flag isn't
set.
Link: https://lore.kernel.org/r/20200322181304.37655-8-jsmart2021@gmail.com
Fixes: b15bd3e621 ("scsi: lpfc: Fix nvme remoteport registration race conditions")
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4cd7089130 ]
Injecting EEH on a 32GB card is causing kernel oops
The pci error handler is doing an IO flush and the offline code is also
doing an IO flush. When the 1st flush is complete the hdwq is destroyed
(freed), yet the second flush accesses the hdwq and crashes.
Added a check in lpfc_sli4_fush_io_rings to check both the HBA_IOQ_FLUSH
flag and the hdwq pointer to see if it is already set and not already
freed.
Link: https://lore.kernel.org/r/20200322181304.37655-6-jsmart2021@gmail.com
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 38503943c8 ]
The following kasan bug was called out:
BUG: KASAN: slab-out-of-bounds in lpfc_unreg_login+0x7c/0xc0 [lpfc]
Read of size 2 at addr ffff889fc7c50a22 by task lpfc_worker_3/6676
...
Call Trace:
dump_stack+0x96/0xe0
? lpfc_unreg_login+0x7c/0xc0 [lpfc]
print_address_description.constprop.6+0x1b/0x220
? lpfc_unreg_login+0x7c/0xc0 [lpfc]
? lpfc_unreg_login+0x7c/0xc0 [lpfc]
__kasan_report.cold.9+0x37/0x7c
? lpfc_unreg_login+0x7c/0xc0 [lpfc]
kasan_report+0xe/0x20
lpfc_unreg_login+0x7c/0xc0 [lpfc]
lpfc_sli_def_mbox_cmpl+0x334/0x430 [lpfc]
...
When processing the completion of a "Reg Rpi" login mailbox command in
lpfc_sli_def_mbox_cmpl, a call may be made to lpfc_unreg_login. The vpi is
extracted from the completing mailbox context and passed as an input for
the next. However, the vpi stored in the mailbox command context is an
absolute vpi, which for SLI4 represents both base + offset. When used with
a non-zero base component, (function id > 0) this results in an
out-of-range access beyond the allocated phba->vpi_ids array.
Fix by subtracting the function's base value to get an accurate vpi number.
Link: https://lore.kernel.org/r/20200322181304.37655-2-jsmart2021@gmail.com
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 982bb70517 ]
Currently the watchdog core does not initialize the last_hw_keepalive
time during watchdog startup. This will cause the watchdog to be pinged
immediately if enough time has passed from the system boot-up time, and
some types of watchdogs like K3 RTI does not like this.
To avoid the issue, setup the last_hw_keepalive time during watchdog
startup.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20200302200426.6492-3-t-kristo@ti.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c0e71d6020 ]
When a kernel is configured without CONFIG_DEV_DAX_PMEM_COMPAT, the
compilation of tools/testing/nvdimm fails with:
Building modules, stage 2.
MODPOST 11 modules
ERROR: "dax_pmem_compat_test" [tools/testing/nvdimm/test/nfit_test.ko] undefined!
Fix the problem by calling dax_pmem_compat_test() only if the kernel has
the required functionality.
Signed-off-by: Jan Kara <jack@suse.cz>
Link: https://lore.kernel.org/r/20200123154720.12097-1-jack@suse.cz
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit: 27a22fbdee ]
Clang reports a warning on the __tlbi(aside1is, 0) macro expansion since
the value size does not match the register size specified in the inline
asm. Construct the ASID value using the __TLBI_VADDR() macro.
Fixes: 222fc0c850 ("arm64: compat: Workaround Neoverse-N1 #1542419 for compat user-space")
Reported-by: Nathan Chancellor <natechancellor@gmail.com>
Cc: James Morse <james.morse@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 222fc0c850 ]
Compat user-space is unable to perform ICIMVAU instructions from
user-space. Instead it uses a compat-syscall. Add the workaround for
Neoverse-N1 #1542419 to this code path.
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
