commit 4fa4302d6d upstream.
Not all decoders have a reset callback.
The CXL specification allows a host bridge with a single root port to
have no explicit HDM decoders. Currently the region driver assumes there
are none. As such the CXL core creates a special pass through decoder
instance without a commit/reset callback.
Prior to this patch, the ->reset() callback was called unconditionally when
calling cxl_region_decode_reset. Thus a configuration with 1 Host Bridge,
1 Root Port, and one directly attached CXL type 3 device or multiple CXL
type 3 devices attached to downstream ports of a switch can cause a null
pointer dereference.
Before the fix, a kernel crash was observed when we destroy the region, and
a pass through decoder is reset.
The issue can be reproduced as below,
1) create a region with a CXL setup which includes a HB with a
single root port under which a memdev is attached directly.
2) destroy the region with cxl destroy-region regionX -f.
Fixes: 176baefb2e ("cxl/hdm: Commit decoder state to hardware")
Cc: <stable@vger.kernel.org>
Signed-off-by: Fan Ni <fan.ni@samsung.com>
Reviewed-by: Davidlohr Bueso <dave@stgolabs.net>
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Tested-by: Gregory Price <gregory.price@memverge.com>
Reviewed-by: Gregory Price <gregory.price@memverge.com>
Link: https://lore.kernel.org/r/20221215170909.2650271-1-fan.ni@samsung.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 54e5c00a4e upstream.
While checking Pin Assignments of the port and partner during probe, we
don't take into account whether the peripheral is a plug or receptacle.
This manifests itself in a mode entry failure on certain docks and
dongles with captive cables. For instance, the Startech.com Type-C to DP
dongle (Model #CDP2DP) advertises its DP VDO as 0x405. This would fail
the Pin Assignment compatibility check, despite it supporting
Pin Assignment C as a UFP.
Update the check to use the correct DP Pin Assign macros that
take the peripheral's receptacle bit into account.
Fixes: c1e5c2f0cb ("usb: typec: altmodes/displayport: correct pin assignment for UFP receptacles")
Cc: stable@vger.kernel.org
Reported-by: Diana Zigterman <dzigterman@chromium.org>
Signed-off-by: Prashant Malani <pmalani@chromium.org>
Link: https://lore.kernel.org/r/20230208205318.131385-1-pmalani@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5f58d783fd upstream.
We have this check to make sure we don't accidentally add older devices
that may have disappeared and re-appeared with an older generation from
being added to an fs_devices (such as a replace source device). This
makes sense, we don't want stale disks in our file system. However for
single disks this doesn't really make sense.
I've seen this in testing, but I was provided a reproducer from a
project that builds btrfs images on loopback devices. The loopback
device gets cached with the new generation, and then if it is re-used to
generate a new file system we'll fail to mount it because the new fs is
"older" than what we have in cache.
Fix this by freeing the cache when closing the device for a single device
filesystem. This will ensure that the mount command passed device path is
scanned successfully during the next mount.
CC: stable@vger.kernel.org # 5.10+
Reported-by: Daan De Meyer <daandemeyer@fb.com>
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Anand Jain <anand.jain@oracle.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 070d6dafac upstream.
These 'endpoint' tests from 'mptcp_join.sh' selftest start a transfer in
the background and check the status during this transfer.
Once the expected events have been recorded, there is no reason to wait
for the data transfer to finish. It can be stopped earlier to reduce the
execution time by more than half.
For these tests, the exchanged data were not verified. Errors, if any,
were ignored but that's fine, plenty of other tests are looking at that.
It is then OK to mute stderr now that we are sure errors will be printed
(and still ignored) because the transfer is stopped before the end.
Fixes: e274f71540 ("selftests: mptcp: add subflow limits test-cases")
Cc: stable@vger.kernel.org
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1249db44a1 upstream.
Currently the subflow error report callback unconditionally
propagates the fallback subflow status to the owning msk.
If the msk is already orphaned, the above prevents the code
from correctly tracking the msk moving to the TCP_CLOSE state
and doing the appropriate cleanup.
All the above causes increasing memory usage over time and
sporadic self-tests failures.
There is a great deal of infrastructure trying to propagate
correctly the fallback subflow status to the owning mptcp socket,
e.g. via mptcp_subflow_eof() and subflow_sched_work_if_closed():
in the error propagation path we need only to cope with unorphaned
sockets.
Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/339
Fixes: 15cc104533 ("mptcp: deliver ssk errors to msk")
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d4e85922e3 upstream.
If the peer closes all the existing subflows for a given
mptcp socket and later the application closes it, the current
implementation let it survive until the timewait timeout expires.
While the above is allowed by the protocol specification it
consumes resources for almost no reason and additionally
causes sporadic self-tests failures.
Let's move the mptcp socket to the TCP_CLOSE state when there are
no alive subflows at close time, so that the allocated resources
will be freed immediately.
Fixes: e16163b6e2 ("mptcp: refactor shutdown and close")
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit aa5465aeca upstream.
When the network status is unstable, use-after-free may occur when
read data from the server.
BUG: KASAN: use-after-free in readpages_fill_pages+0x14c/0x7e0
Call Trace:
<TASK>
dump_stack_lvl+0x38/0x4c
print_report+0x16f/0x4a6
kasan_report+0xb7/0x130
readpages_fill_pages+0x14c/0x7e0
cifs_readv_receive+0x46d/0xa40
cifs_demultiplex_thread+0x121c/0x1490
kthread+0x16b/0x1a0
ret_from_fork+0x2c/0x50
</TASK>
Allocated by task 2535:
kasan_save_stack+0x22/0x50
kasan_set_track+0x25/0x30
__kasan_kmalloc+0x82/0x90
cifs_readdata_direct_alloc+0x2c/0x110
cifs_readdata_alloc+0x2d/0x60
cifs_readahead+0x393/0xfe0
read_pages+0x12f/0x470
page_cache_ra_unbounded+0x1b1/0x240
filemap_get_pages+0x1c8/0x9a0
filemap_read+0x1c0/0x540
cifs_strict_readv+0x21b/0x240
vfs_read+0x395/0x4b0
ksys_read+0xb8/0x150
do_syscall_64+0x3f/0x90
entry_SYSCALL_64_after_hwframe+0x72/0xdc
Freed by task 79:
kasan_save_stack+0x22/0x50
kasan_set_track+0x25/0x30
kasan_save_free_info+0x2e/0x50
__kasan_slab_free+0x10e/0x1a0
__kmem_cache_free+0x7a/0x1a0
cifs_readdata_release+0x49/0x60
process_one_work+0x46c/0x760
worker_thread+0x2a4/0x6f0
kthread+0x16b/0x1a0
ret_from_fork+0x2c/0x50
Last potentially related work creation:
kasan_save_stack+0x22/0x50
__kasan_record_aux_stack+0x95/0xb0
insert_work+0x2b/0x130
__queue_work+0x1fe/0x660
queue_work_on+0x4b/0x60
smb2_readv_callback+0x396/0x800
cifs_abort_connection+0x474/0x6a0
cifs_reconnect+0x5cb/0xa50
cifs_readv_from_socket.cold+0x22/0x6c
cifs_read_page_from_socket+0xc1/0x100
readpages_fill_pages.cold+0x2f/0x46
cifs_readv_receive+0x46d/0xa40
cifs_demultiplex_thread+0x121c/0x1490
kthread+0x16b/0x1a0
ret_from_fork+0x2c/0x50
The following function calls will cause UAF of the rdata pointer.
readpages_fill_pages
cifs_read_page_from_socket
cifs_readv_from_socket
cifs_reconnect
__cifs_reconnect
cifs_abort_connection
mid->callback() --> smb2_readv_callback
queue_work(&rdata->work) # if the worker completes first,
# the rdata is freed
cifs_readv_complete
kref_put
cifs_readdata_release
kfree(rdata)
return rdata->... # UAF in readpages_fill_pages()
Similarly, this problem also occurs in the uncache_fill_pages().
Fix this by adjusts the order of condition judgment in the return
statement.
Signed-off-by: ZhaoLong Wang <wangzhaolong1@huawei.com>
Cc: stable@vger.kernel.org
Acked-by: Paulo Alcantara (SUSE) <pc@cjr.nz>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 606d4ef492 ]
This reverts commit cf517fef60.
The commit cf517fef60 ("pinctrl: aspeed: Force to disable the
function's signal") exposed a problem with fetching the regmap for
reading the GFX register.
The Romulus machine the device tree contains a gpio hog for GPIO S7.
With the patch applied:
Muxing pin 151 for GPIO
Disabling signal VPOB9 for VPO
aspeed-g5-pinctrl 1e6e2080.pinctrl: Failed to acquire regmap for IP block 1
aspeed-g5-pinctrl 1e6e2080.pinctrl: request() failed for pin 151
The code path is aspeed-gpio -> pinmux-g5 -> regmap -> clk, and the
of_clock code returns an error as it doesn't have a valid struct clk_hw
pointer. The regmap call happens because pinmux wants to check the GFX
node (IP block 1) to query bits there.
For reference, before the offending patch:
Muxing pin 151 for GPIO
Disabling signal VPOB9 for VPO
Want SCU8C[0x00000080]=0x1, got 0x0 from 0x00000000
Disabling signal VPOB9 for VPOOFF1
Want SCU8C[0x00000080]=0x1, got 0x0 from 0x00000000
Disabling signal VPOB9 for VPOOFF2
Want SCU8C[0x00000080]=0x1, got 0x0 from 0x00000000
Enabling signal GPIOS7 for GPIOS7
Muxed pin 151 as GPIOS7
gpio-943 (seq_cont): hogged as output/low
We can't skip the clock check to allow pinmux to proceed, because the
write to disable VPOB9 will try to set a bit in the GFX register space
which will not stick when the IP is in reset. However, we do not want to
enable the IP just so pinmux can do a disable-enable dance for the pin.
For now, revert the offending patch while a correct solution is found.
Fixes: cf517fef60 ("pinctrl: aspeed: Force to disable the function's signal")
Link: https://github.com/openbmc/linux/issues/218
Signed-off-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20230130220845.917985-1-joel@jms.id.au
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c63b8fd14a ]
Due to using the u16 type in the min_t() macros the SPI transfer length
will be cast to word before participating in the conditional statement
implied by the macro. Thus if the transfer length is greater than 64KB the
Tx/Rx FIFO threshold level value will be determined by the leftover of the
truncated after the type-case length. In the worst case it will cause the
dramatical performance drop due to the "Tx FIFO Empty" or "Rx FIFO Full"
interrupts triggered on each xfer word sent/received to/from the bus.
The problem can be easily fixed by specifying the unsigned int type in the
min_t() macros thus preventing the possible data loss.
Fixes: ea11370fff ("spi: dw: get TX level without an additional variable")
Reported-by: Sergey Nazarov <Sergey.Nazarov@baikalelectronics.ru>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230113185942.2516-1-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 86d884f528 ]
In various places, string buffers of a fixed size are allocated, and
filled using snprintf() with the same fixed size, which is error-prone.
Replace this by calling devm_kasprintf() instead, which always uses the
appropriate size.
While at it, remove an unneeded intermediate variable, which allows us
to drop a cast as a bonus.
With the initial behavior it would have been possible to have a device tree
with a node address that would make "ccc<node_address>_pll<N>" exceed
18 characters. If that happened, the <N> would be cut off & both
pll 0 & 1 would be named identically. If that happens, pll1 would fail
to register. Thus, the fixes tag has been added to this commit.
Fixes: d39fb17276 ("clk: microchip: add PolarFire SoC fabric clock support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Tested-by: Conor Dooley <conor.dooley@microchip.com>
[claudiu.beznea: added the rationale behind fixes tag]
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/f904fd28b2087d1463ea65f059924e3b1acc193c.1672764239.git.geert+renesas@glider.be
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1473237926 ]
There's some setup we need to do in order to get the DSP initialized,
and this can't be done until a bit-clock is ready. In an earlier version
of this driver, this work was done in a DAPM callback.
The DAPM callback doesn't guarantee that the bit-clock is running, so
the work was moved instead to the trigger callback. Unfortunately this
callback runs in atomic context, and the setup code needs to do I2C
transactions.
Here we use a work_struct to kick off the setup in a thread instead.
Fixes: ec45268467 ("ASoC: add support for TAS5805M digital amplifier")
Signed-off-by: Daniel Beer <daniel.beer@igorinstitute.com>
Link: https://lore.kernel.org/r/85d8ba405cb009a7a3249b556dc8f3bdb1754fdf.1675497326.git.daniel.beer@igorinstitute.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 97801cfcf9 ]
When vdosys1 was initially added, it was incorrectly assumed to be
compatible with vdosys0, and thus both had the same mt8195-mmsys
compatible attached.
This has since been corrected in commit b237efd47d ("dt-bindings:
arm: mediatek: mmsys: change compatible for MT8195") and commit
82219cfbef ("dt-bindings: arm: mediatek: mmsys: add vdosys1 compatible
for MT8195"). The device tree needs to be fixed as well, otherwise
the vdosys1 block fails to work, and causes its dependent power domain
controller to not work either.
Change the compatible string of vdosys1 to "mediatek,mt8195-vdosys1".
While at it, also add the new "mediatek,mt8195-vdosys0" compatible to
vdosys0.
Fixes: 6aa5b46d17 ("arm64: dts: mt8195: Add vdosys and vppsys clock nodes")
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Tested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Acked-by: Matthias Brugger <matthias.bgg@gmail.com>
Link: https://lore.kernel.org/r/20230202104014.2931517-1-wenst@chromium.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cb80242cc6 ]
When running kfence_test, I found some testcases failed like this:
# test_out_of_bounds_read: EXPECTATION FAILED at mm/kfence/kfence_test.c:346
Expected report_matches(&expect) to be true, but is false
not ok 1 - test_out_of_bounds_read
The corresponding call-trace is:
BUG: KFENCE: out-of-bounds read in kunit_try_run_case+0x38/0x84
Out-of-bounds read at 0x(____ptrval____) (32B right of kfence-#10):
kunit_try_run_case+0x38/0x84
kunit_generic_run_threadfn_adapter+0x12/0x1e
kthread+0xc8/0xde
ret_from_exception+0x0/0xc
The kfence_test using the first frame of call trace to check whether the
testcase is succeed or not. Commit 6a00ef4493 ("riscv: eliminate
unreliable __builtin_frame_address(1)") skip first frame for all
case, which results the kfence_test failed. Indeed, we only need to skip
the first frame for case (task==NULL || task==current).
With this patch, the call-trace will be:
BUG: KFENCE: out-of-bounds read in test_out_of_bounds_read+0x88/0x19e
Out-of-bounds read at 0x(____ptrval____) (1B left of kfence-#7):
test_out_of_bounds_read+0x88/0x19e
kunit_try_run_case+0x38/0x84
kunit_generic_run_threadfn_adapter+0x12/0x1e
kthread+0xc8/0xde
ret_from_exception+0x0/0xc
Fixes: 6a00ef4493 ("riscv: eliminate unreliable __builtin_frame_address(1)")
Signed-off-by: Liu Shixin <liushixin2@huawei.com>
Tested-by: Samuel Holland <samuel@sholland.org>
Link: https://lore.kernel.org/r/20221207025038.1022045-1-liushixin2@huawei.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5dac9f8dc2 ]
This loop accidentally reuses the "i" iterator for both the inside and
the outside loop. The value of MAX_STREAM_BUFFER is 5. I believe that
chip->rmh.stat_len is in the 2-12 range. If the value of .stat_len is
4 or more then it will loop exactly one time, but if it's less then it
is a forever loop.
It looks like it was supposed to combined into one loop where
conditions are checked.
Fixes: 8e6320064c ("ALSA: lx_core: Remove useless #if 0 .. #endif")
Signed-off-by: Dan Carpenter <error27@gmail.com>
Link: https://lore.kernel.org/r/Y9jnJTis/mRFJAQp@kili
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6f515b663d ]
When the input enable pinconf was introduced, a default drive-strength
value of 2 was set for the pull up/down configs. However, this parameter
is unneeded when configuring the pin as input, and having a single
hardcoded value here is actually harmful: GPIOs on the RK3399 have
various same drive-strength capabilities depending on the bank and port
they belong to.
As an example, trying to configure the GPIO4_PD3 pin as an input with
pull-up enabled fails with the following output:
[ 10.706542] rockchip-pinctrl pinctrl: unsupported driver strength 2
[ 10.713661] rockchip-pinctrl pinctrl: pin_config_set op failed for pin 155
(acceptable drive-strength values for this pin being 3, 6, 9 and 12)
Let's drop the drive-strength property from all input pinconfs in order
to solve this issue.
Fixes: ec48c3e82c ("arm64: dts: rockchip: add an input enable pinconf to rk3399")
Signed-off-by: Arnaud Ferraris <arnaud.ferraris@collabora.com>
Reviewed-by: Caleb Connolly <kc@postmarketos.org>
Link: https://lore.kernel.org/r/20221215101947.254896-1-arnaud.ferraris@collabora.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2fcde9fe25 ]
While running this selftest which usually passes:
~/selftests/drivers/net/dsa# ./local_termination.sh eno0 swp0
TEST: swp0: Unicast IPv4 to primary MAC address [ OK ]
TEST: swp0: Unicast IPv4 to macvlan MAC address [ OK ]
TEST: swp0: Unicast IPv4 to unknown MAC address [ OK ]
TEST: swp0: Unicast IPv4 to unknown MAC address, promisc [ OK ]
TEST: swp0: Unicast IPv4 to unknown MAC address, allmulti [ OK ]
TEST: swp0: Multicast IPv4 to joined group [ OK ]
TEST: swp0: Multicast IPv4 to unknown group [ OK ]
TEST: swp0: Multicast IPv4 to unknown group, promisc [ OK ]
TEST: swp0: Multicast IPv4 to unknown group, allmulti [ OK ]
TEST: swp0: Multicast IPv6 to joined group [ OK ]
TEST: swp0: Multicast IPv6 to unknown group [ OK ]
TEST: swp0: Multicast IPv6 to unknown group, promisc [ OK ]
TEST: swp0: Multicast IPv6 to unknown group, allmulti [ OK ]
if I start PTP timestamping then run it again (debug prints added by me),
the unknown IPv6 MC traffic is seen by the CPU port even when it should
have been dropped:
~/selftests/drivers/net/dsa# ptp4l -i swp0 -2 -P -m
ptp4l[225.410]: selected /dev/ptp1 as PTP clock
[ 225.445746] mscc_felix 0000:00:00.5: ocelot_l2_ptp_trap_add: port 0 adding L2 PTP trap
[ 225.453815] mscc_felix 0000:00:00.5: ocelot_ipv4_ptp_trap_add: port 0 adding IPv4 PTP event trap
[ 225.462703] mscc_felix 0000:00:00.5: ocelot_ipv4_ptp_trap_add: port 0 adding IPv4 PTP general trap
[ 225.471768] mscc_felix 0000:00:00.5: ocelot_ipv6_ptp_trap_add: port 0 adding IPv6 PTP event trap
[ 225.480651] mscc_felix 0000:00:00.5: ocelot_ipv6_ptp_trap_add: port 0 adding IPv6 PTP general trap
ptp4l[225.488]: port 1: INITIALIZING to LISTENING on INIT_COMPLETE
ptp4l[225.488]: port 0: INITIALIZING to LISTENING on INIT_COMPLETE
^C
~/selftests/drivers/net/dsa# ./local_termination.sh eno0 swp0
TEST: swp0: Unicast IPv4 to primary MAC address [ OK ]
TEST: swp0: Unicast IPv4 to macvlan MAC address [ OK ]
TEST: swp0: Unicast IPv4 to unknown MAC address [ OK ]
TEST: swp0: Unicast IPv4 to unknown MAC address, promisc [ OK ]
TEST: swp0: Unicast IPv4 to unknown MAC address, allmulti [ OK ]
TEST: swp0: Multicast IPv4 to joined group [ OK ]
TEST: swp0: Multicast IPv4 to unknown group [ OK ]
TEST: swp0: Multicast IPv4 to unknown group, promisc [ OK ]
TEST: swp0: Multicast IPv4 to unknown group, allmulti [ OK ]
TEST: swp0: Multicast IPv6 to joined group [ OK ]
TEST: swp0: Multicast IPv6 to unknown group [FAIL]
reception succeeded, but should have failed
TEST: swp0: Multicast IPv6 to unknown group, promisc [ OK ]
TEST: swp0: Multicast IPv6 to unknown group, allmulti [ OK ]
The PGID_MCIPV6 is configured correctly to not flood to the CPU,
I checked that.
Furthermore, when I disable back PTP RX timestamping (ptp4l doesn't do
that when it exists), packets are RX filtered again as they should be:
~/selftests/drivers/net/dsa# hwstamp_ctl -i swp0 -r 0
[ 218.202854] mscc_felix 0000:00:00.5: ocelot_l2_ptp_trap_del: port 0 removing L2 PTP trap
[ 218.212656] mscc_felix 0000:00:00.5: ocelot_ipv4_ptp_trap_del: port 0 removing IPv4 PTP event trap
[ 218.222975] mscc_felix 0000:00:00.5: ocelot_ipv4_ptp_trap_del: port 0 removing IPv4 PTP general trap
[ 218.233133] mscc_felix 0000:00:00.5: ocelot_ipv6_ptp_trap_del: port 0 removing IPv6 PTP event trap
[ 218.242251] mscc_felix 0000:00:00.5: ocelot_ipv6_ptp_trap_del: port 0 removing IPv6 PTP general trap
current settings:
tx_type 1
rx_filter 12
new settings:
tx_type 1
rx_filter 0
~/selftests/drivers/net/dsa# ./local_termination.sh eno0 swp0
TEST: swp0: Unicast IPv4 to primary MAC address [ OK ]
TEST: swp0: Unicast IPv4 to macvlan MAC address [ OK ]
TEST: swp0: Unicast IPv4 to unknown MAC address [ OK ]
TEST: swp0: Unicast IPv4 to unknown MAC address, promisc [ OK ]
TEST: swp0: Unicast IPv4 to unknown MAC address, allmulti [ OK ]
TEST: swp0: Multicast IPv4 to joined group [ OK ]
TEST: swp0: Multicast IPv4 to unknown group [ OK ]
TEST: swp0: Multicast IPv4 to unknown group, promisc [ OK ]
TEST: swp0: Multicast IPv4 to unknown group, allmulti [ OK ]
TEST: swp0: Multicast IPv6 to joined group [ OK ]
TEST: swp0: Multicast IPv6 to unknown group [ OK ]
TEST: swp0: Multicast IPv6 to unknown group, promisc [ OK ]
TEST: swp0: Multicast IPv6 to unknown group, allmulti [ OK ]
So it's clear that something in the PTP RX trapping logic went wrong.
Looking a bit at the code, I can see that there are 4 typos, which
populate "ipv4" VCAP IS2 key filter fields for IPv6 keys.
VCAP IS2 keys of type OCELOT_VCAP_KEY_IPV4 and OCELOT_VCAP_KEY_IPV6 are
handled by is2_entry_set(). OCELOT_VCAP_KEY_IPV4 looks at
&filter->key.ipv4, and OCELOT_VCAP_KEY_IPV6 at &filter->key.ipv6.
Simply put, when we populate the wrong key field, &filter->key.ipv6
fields "proto.mask" and "proto.value" remain all zeroes (or "don't care").
So is2_entry_set() will enter the "else" of this "if" condition:
if (msk == 0xff && (val == IPPROTO_TCP || val == IPPROTO_UDP))
and proceed to ignore the "proto" field. The resulting rule will match
on all IPv6 traffic, trapping it to the CPU.
This is the reason why the local_termination.sh selftest sees it,
because control traps are stronger than the PGID_MCIPV6 used for
flooding (from the forwarding data path).
But the problem is in fact much deeper. We trap all IPv6 traffic to the
CPU, but if we're bridged, we set skb->offload_fwd_mark = 1, so software
forwarding will not take place and IPv6 traffic will never reach its
destination.
The fix is simple - correct the typos.
I was intentionally inaccurate in the commit message about the breakage
occurring when any PTP timestamping is enabled. In fact it only happens
when L4 timestamping is requested (HWTSTAMP_FILTER_PTP_V2_EVENT or
HWTSTAMP_FILTER_PTP_V2_L4_EVENT). But ptp4l requests a larger RX
timestamping filter than it needs for "-2": HWTSTAMP_FILTER_PTP_V2_EVENT.
I wanted people skimming through git logs to not think that the bug
doesn't affect them because they only use ptp4l in L2 mode.
Fixes: 96ca08c058 ("net: mscc: ocelot: set up traps for PTP packets")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230207183117.1745754-1-vladimir.oltean@nxp.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c11204c78d ]
This code fix a bug that sk->sk_txrehash gets its default enable
value from sysctl_txrehash only when the socket is a TCP listener.
We should have sysctl_txrehash to set the default sk->sk_txrehash,
no matter TCP, nor listerner/connector.
Tested by following packetdrill:
0 socket(..., SOCK_STREAM, IPPROTO_TCP) = 3
+0 socket(..., SOCK_DGRAM, IPPROTO_UDP) = 4
// SO_TXREHASH == 74, default to sysctl_txrehash == 1
+0 getsockopt(3, SOL_SOCKET, 74, [1], [4]) = 0
+0 getsockopt(4, SOL_SOCKET, 74, [1], [4]) = 0
Fixes: 26859240e4 ("txhash: Add socket option to control TX hash rethink behavior")
Signed-off-by: Kevin Yang <yyd@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c966153d12 ]
Parameters 'queue_index' and 'napi_id' are passed in a swapped order.
Fix it here.
Fixes: 23233e577e ("net: ethernet: mtk_eth_soc: rely on page_pool for single page buffers")
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9b27517627 ]
On some platforms, 100/1000/2500 speeds seem to have sometimes problems
reporting false positive tx unit hang during stressful UDP traffic. Likely
other Intel drivers introduce responses to a tx hang. Update the 'tx hang'
comparator with the comparison of the head and tail of ring pointers and
restore the tx_timeout_factor to the previous value (one).
This can be test by using netperf or iperf3 applications.
Example:
iperf3 -s -p 5001
iperf3 -c 192.168.0.2 --udp -p 5001 --time 600 -b 0
netserver -p 16604
netperf -H 192.168.0.2 -l 600 -p 16604 -t UDP_STREAM -- -m 64000
Fixes: b27b8dc77b ("igc: Increase timeout value for Speed 100/1000/2500")
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20230206235818.662384-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8f0d1451ec ]
Currently, remove and reload flows can run in parallel to module cleanup.
This design is error prone. For example: aux_drivers callbacks are called
from both cleanup and remove flows with different lockings, which can
cause a deadlock[1].
Hence, serialize module cleanup with reload and remove.
[1]
cleanup remove
------- ------
auxiliary_driver_unregister();
devl_lock()
auxiliary_device_delete(mlx5e_aux)
device_lock(mlx5e_aux)
devl_lock()
device_lock(mlx5e_aux)
Fixes: 912cebf420 ("net/mlx5e: Connect ethernet part to auxiliary bus")
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 184e1e4474 ]
When tracer is reloaded, the device will log the traces at the
beginning of the log buffer. Also, driver is reading the log buffer in
chunks in accordance to the consumer index.
Hence, zero consumer index when reloading the tracer.
Fixes: 4383cfcc65 ("net/mlx5: Add devlink reload")
Signed-off-by: Shay Drory <shayd@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit db561fed6b ]
Whenever the driver is reading the string DBs into buffers, the driver
is setting the load bit, but the driver never clears this bit.
As a result, in case load bit is on and the driver query the device for
new string DBs, the driver won't read again the string DBs.
Fix it by clearing the load bit when query the device for new string
DBs.
Fixes: 2d69356752 ("net/mlx5: Add support for fw live patch event")
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9965bbebae ]
Currently, each core device has VF pages counter which stores number of
fw pages used by its VFs and SFs.
The current design led to a hang when performing firmware reset on DPU,
where the DPU PFs stalled in sriov unload flow due to waiting on release
of SFs pages instead of waiting on only VFs pages.
Thus, Add a separate counter for SF firmware pages, which will prevent
the stall scenario described above.
Fixes: 1958fc2f07 ("net/mlx5: SF, Add auxiliary device driver")
Signed-off-by: Maher Sanalla <msanalla@nvidia.com>
Reviewed-by: Shay Drory <shayd@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c3bdbaea65 ]
Currently, an independent page counter is used for tracking memory usage
for each function type such as VF, PF and host PF (DPU).
For better code-readibilty, use a single array that stores
the number of allocated memory pages for each function type.
Signed-off-by: Maher Sanalla <msanalla@nvidia.com>
Reviewed-by: Shay Drory <shayd@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Stable-dep-of: 9965bbebae ("net/mlx5: Expose SF firmware pages counter")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8aa5f171d5 ]
ethtool is returning an error for unknown speeds for the IPoIB interface:
$ ethtool ib0
netlink error: failed to retrieve link settings
netlink error: Invalid argument
netlink error: failed to retrieve link settings
netlink error: Invalid argument
Settings for ib0:
Link detected: no
After this change, ethtool will return success and show "unknown speed":
$ ethtool ib0
Settings for ib0:
Supported ports: [ ]
Supported link modes: Not reported
Supported pause frame use: No
Supports auto-negotiation: No
Supported FEC modes: Not reported
Advertised link modes: Not reported
Advertised pause frame use: No
Advertised auto-negotiation: No
Advertised FEC modes: Not reported
Speed: Unknown!
Duplex: Full
Auto-negotiation: off
Port: Other
PHYAD: 0
Transceiver: internal
Link detected: no
Fixes: eb234ee9d5 ("net/mlx5e: IPoIB, Add support for get_link_ksettings in ethtool")
Signed-off-by: Dragos Tatulea <dtatulea@nvidia.com>
Reviewed-by: Gal Pressman <gal@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8974aa9638 ]
Moving to switchdev mode with rx-vlan-filter on and then setting it off
causes the kernel to crash since fs->vlan is freed during nic profile
cleanup flow.
RX VLAN filtering is not supported in switchdev mode so unset it when
changing to switchdev and restore its value when switching back to
legacy.
trace:
[] RIP: 0010:mlx5e_disable_cvlan_filter+0x43/0x70
[] set_feature_cvlan_filter+0x37/0x40 [mlx5_core]
[] mlx5e_handle_feature+0x3a/0x60 [mlx5_core]
[] mlx5e_set_features+0x6d/0x160 [mlx5_core]
[] __netdev_update_features+0x288/0xa70
[] ethnl_set_features+0x309/0x380
[] ? __nla_parse+0x21/0x30
[] genl_family_rcv_msg_doit.isra.17+0x110/0x150
[] genl_rcv_msg+0x112/0x260
[] ? features_reply_size+0xe0/0xe0
[] ? genl_family_rcv_msg_doit.isra.17+0x150/0x150
[] netlink_rcv_skb+0x4e/0x100
[] genl_rcv+0x24/0x40
[] netlink_unicast+0x1ab/0x290
[] netlink_sendmsg+0x257/0x4f0
[] sock_sendmsg+0x5c/0x70
Fixes: cb67b83292 ("net/mlx5e: Introduce SRIOV VF representors")
Signed-off-by: Amir Tzin <amirtz@nvidia.com>
Reviewed-by: Maor Dickman <maord@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit da0c52426c ]
SWITCHDEV_FDB_ADD_TO_BRIDGE event handler that updates FDB entry 'lastuse'
field is only executed for eswitch that owns the entry. However, if peer
entry processed packets at least once it will have hardware counter 'used'
value greater than entry 'lastuse' from that point on, which will cause FDB
entry not being aged out.
Process the event on all eswitch instances.
Fixes: ff9b752146 ("net/mlx5: Bridge, support LAG")
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Reviewed-by: Maor Dickman <maord@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1e66220948 ]
rq->hw_mtu is used in function en_rx.c/mlx5e_skb_from_cqe_mpwrq_linear()
to catch oversized packets. If FCS is concatenated to the end of the
packet then the check should be updated accordingly.
Rx rings initialization (mlx5e_init_rxq_rq()) invoked for every new set
of channels, as part of mlx5e_safe_switch_params(), unknowingly if it
runs with default configuration or not. Current rq->hw_mtu
initialization assumes default configuration and ignores
params->scatter_fcs_en flag state.
Fix this, by accounting for params->scatter_fcs_en flag state during
rq->hw_mtu initialization.
In addition, updating rq->hw_mtu value during ingress traffic might
lead to packets drop and oversize_pkts_sw_drop counter increase with no
good reason. Hence we remove this optimization and switch the set of
channels with a new one, to make sure we don't get false positives on
the oversize_pkts_sw_drop counter.
Fixes: 102722fc68 ("net/mlx5e: Add support for RXFCS feature flag")
Signed-off-by: Adham Faris <afaris@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f964f8399d ]
Alternative short title: don't instruct the hardware to match on
EtherType with "protocol 802.1Q" flower filters. It doesn't work for the
reasons detailed below.
With a command such as the following:
tc filter add dev $swp1 ingress chain $(IS1 2) pref 3 \
protocol 802.1Q flower skip_sw vlan_id 200 src_mac $h1_mac \
action vlan modify id 300 \
action goto chain $(IS2 0 0)
the created filter is set by ocelot_flower_parse_key() to be of type
OCELOT_VCAP_KEY_ETYPE, and etype is set to {value=0x8100, mask=0xffff}.
This gets propagated all the way to is1_entry_set() which commits it to
hardware (the VCAP_IS1_HK_ETYPE field of the key). Compare this to the
case where src_mac isn't specified - the key type is OCELOT_VCAP_KEY_ANY,
and is1_entry_set() doesn't populate VCAP_IS1_HK_ETYPE.
The problem is that for VLAN-tagged frames, the hardware interprets the
ETYPE field as holding the encapsulated VLAN protocol. So the above
filter will only match those packets which have an encapsulated protocol
of 0x8100, rather than all packets with VLAN ID 200 and the given src_mac.
The reason why this is allowed to occur is because, although we have a
block of code in ocelot_flower_parse_key() which sets "match_protocol"
to false when VLAN keys are present, that code executes too late.
There is another block of code, which executes for Ethernet addresses,
and has a "goto finished_key_parsing" and skips the VLAN header parsing.
By skipping it, "match_protocol" remains with the value it was
initialized with, i.e. "true", and "proto" is set to f->common.protocol,
or 0x8100.
The concept of ignoring some keys rather than erroring out when they are
present but can't be offloaded is dubious in itself, but is present
since the initial commit fe3490e610 ("net: mscc: ocelot: Hardware
ofload for tc flower filter"), and it's outside of the scope of this
patch to change that.
The problem was introduced when the driver started to interpret the
flower filter's protocol, and populate the VCAP filter's ETYPE field
based on it.
To fix this, it is sufficient to move the code that parses the VLAN keys
earlier than the "goto finished_key_parsing" instruction. This will
ensure that if we have a flower filter with both VLAN and Ethernet
address keys, it won't match on ETYPE 0x8100, because the VLAN key
parsing sets "match_protocol = false".
Fixes: 86b956de11 ("net: mscc: ocelot: support matching on EtherType")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230205192409.1796428-1-vladimir.oltean@nxp.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0b6d642510 ]
Frank reports that in a mt7530 setup where some ports are standalone and
some are in a VLAN-aware bridge, 8021q uppers of the standalone ports
lose their VLAN tag on xmit, as seen by the link partner.
This seems to occur because once the other ports join the VLAN-aware
bridge, mt7530_port_vlan_filtering() also calls
mt7530_port_set_vlan_aware(ds, cpu_dp->index), and this affects the way
that the switch processes the traffic of the standalone port.
Relevant is the PVC_EG_TAG bit. The MT7530 documentation says about it:
EG_TAG: Incoming Port Egress Tag VLAN Attribution
0: disabled (system default)
1: consistent (keep the original ingress tag attribute)
My interpretation is that this setting applies on the ingress port, and
"disabled" is basically the normal behavior, where the egress tag format
of the packet (tagged or untagged) is decided by the VLAN table
(MT7530_VLAN_EGRESS_UNTAG or MT7530_VLAN_EGRESS_TAG).
But there is also an option of overriding the system default behavior,
and for the egress tagging format of packets to be decided not by the
VLAN table, but simply by copying the ingress tag format (if ingress was
tagged, egress is tagged; if ingress was untagged, egress is untagged;
aka "consistent). This is useful in 2 scenarios:
- VLAN-unaware bridge ports will always encounter a miss in the VLAN
table. They should forward a packet as-is, though. So we use
"consistent" there. See commit e045124e93 ("net: dsa: mt7530: fix
tagged frames pass-through in VLAN-unaware mode").
- Traffic injected from the CPU port. The operating system is in god
mode; if it wants a packet to exit as VLAN-tagged, it sends it as
VLAN-tagged. Otherwise it sends it as VLAN-untagged*.
*This is true only if we don't consider the bridge TX forwarding offload
feature, which mt7530 doesn't support.
So for now, make the CPU port always stay in "consistent" mode to allow
software VLANs to be forwarded to their egress ports with the VLAN tag
intact, and not stripped.
Link: https://lore.kernel.org/netdev/trinity-e6294d28-636c-4c40-bb8b-b523521b00be-1674233135062@3c-app-gmx-bs36/
Fixes: e045124e93 ("net: dsa: mt7530: fix tagged frames pass-through in VLAN-unaware mode")
Reported-by: Frank Wunderlich <frank-w@public-files.de>
Tested-by: Frank Wunderlich <frank-w@public-files.de>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20230205140713.1609281-1-vladimir.oltean@nxp.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c793f8ea15 ]
If the user turns on the vf-true-promiscuous-support flag, then Rx VLAN
filtering will be disabled if the VF requests to enable promiscuous
mode. When the VF is in a port VLAN, this is the incorrect behavior
because it will allow the VF to receive traffic outside of its port VLAN
domain. Fortunately this only resulted in the VF(s) receiving broadcast
traffic outside of the VLAN domain because all of the VLAN promiscuous
rules are based on the port VLAN ID. Fix this by setting the
.disable_rx_filtering VLAN op to a no-op when a port VLAN is enabled on
the VF.
Also, make sure to make this fix for both Single VLAN Mode and Double
VLAN Mode enabled devices.
Fixes: c31af68a1b ("ice: Add outer_vlan_ops and VSI specific VLAN ops implementations")
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Karen Ostrowska <karen.ostrowska@intel.com>
Tested-by: Marek Szlosek <marek.szlosek@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7a2127e66a ]
set_cpus_allowed_ptr() will fail with -EINVAL if the requested
affinity mask is not a subset of the task_cpu_possible_mask() for the
task being updated. Consequently, on a heterogeneous system with cpusets
spanning the different CPU types, updates to the cgroup hierarchy can
silently fail to update task affinities when the effective affinity
mask for the cpuset is expanded.
For example, consider an arm64 system with 4 CPUs, where CPUs 2-3 are
the only cores capable of executing 32-bit tasks. Attaching a 32-bit
task to a cpuset containing CPUs 0-2 will correctly affine the task to
CPU 2. Extending the cpuset to CPUs 0-3, however, will fail to extend
the affinity mask of the 32-bit task because update_tasks_cpumask() will
pass the full 0-3 mask to set_cpus_allowed_ptr().
Extend update_tasks_cpumask() to take a temporary 'cpumask' paramater
and use it to mask the 'effective_cpus' mask with the possible mask for
each task being updated.
Fixes: 431c69fac0 ("cpuset: Honour task_cpu_possible_mask() in guarantee_online_cpus()")
Signed-off-by: Will Deacon <will@kernel.org>
Acked-by: Waiman Long <longman@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
