commit de6b43798d9043a7c749a0428dbb02d5fff156e5 upstream.
Currently, the RIIC driver may run the I2C bus faster than requested,
which may cause subtle failures. E.g. Biju reported a measured bus
speed of 450 kHz instead of the expected maximum of 400 kHz on RZ/G2L.
The initial calculation of the bus period uses DIV_ROUND_UP(), to make
sure the actual bus speed never becomes faster than the requested bus
speed. However, the subsequent division-by-two steps do not use
round-up, which may lead to a too-small period, hence a too-fast and
possible out-of-spec bus speed. E.g. on RZ/Five, requesting a bus speed
of 100 resp. 400 kHz will yield too-fast target bus speeds of 100806
resp. 403226 Hz instead of 97656 resp. 390625 Hz.
Fix this by using DIV_ROUND_UP() in the subsequent divisions, too.
Tested on RZ/A1H, RZ/A2M, and RZ/Five.
Fixes: d982d66514 ("i2c: riic: remove clock and frequency restrictions")
Reported-by: Biju Das <biju.das.jz@bp.renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: <stable@vger.kernel.org> # v4.15+
Link: https://lore.kernel.org/r/c59aea77998dfea1b4456c4b33b55ab216fcbf5e.1732284746.git.geert+renesas@glider.be
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1201f226c863b7da739f7420ddba818cedf372fc upstream.
Snapshot the output of CPUID.0xD.[1..n] during kvm.ko initiliaization to
avoid the overead of CPUID during runtime. The offset, size, and metadata
for CPUID.0xD.[1..n] sub-leaves does not depend on XCR0 or XSS values, i.e.
is constant for a given CPU, and thus can be cached during module load.
On Intel's Emerald Rapids, CPUID is *wildly* expensive, to the point where
recomputing XSAVE offsets and sizes results in a 4x increase in latency of
nested VM-Enter and VM-Exit (nested transitions can trigger
xstate_required_size() multiple times per transition), relative to using
cached values. The issue is easily visible by running `perf top` while
triggering nested transitions: kvm_update_cpuid_runtime() shows up at a
whopping 50%.
As measured via RDTSC from L2 (using KVM-Unit-Test's CPUID VM-Exit test
and a slightly modified L1 KVM to handle CPUID in the fastpath), a nested
roundtrip to emulate CPUID on Skylake (SKX), Icelake (ICX), and Emerald
Rapids (EMR) takes:
SKX 11650
ICX 22350
EMR 28850
Using cached values, the latency drops to:
SKX 6850
ICX 9000
EMR 7900
The underlying issue is that CPUID itself is slow on ICX, and comically
slow on EMR. The problem is exacerbated on CPUs which support XSAVES
and/or XSAVEC, as KVM invokes xstate_required_size() twice on each
runtime CPUID update, and because there are more supported XSAVE features
(CPUID for supported XSAVE feature sub-leafs is significantly slower).
SKX:
CPUID.0xD.2 = 348 cycles
CPUID.0xD.3 = 400 cycles
CPUID.0xD.4 = 276 cycles
CPUID.0xD.5 = 236 cycles
<other sub-leaves are similar>
EMR:
CPUID.0xD.2 = 1138 cycles
CPUID.0xD.3 = 1362 cycles
CPUID.0xD.4 = 1068 cycles
CPUID.0xD.5 = 910 cycles
CPUID.0xD.6 = 914 cycles
CPUID.0xD.7 = 1350 cycles
CPUID.0xD.8 = 734 cycles
CPUID.0xD.9 = 766 cycles
CPUID.0xD.10 = 732 cycles
CPUID.0xD.11 = 718 cycles
CPUID.0xD.12 = 734 cycles
CPUID.0xD.13 = 1700 cycles
CPUID.0xD.14 = 1126 cycles
CPUID.0xD.15 = 898 cycles
CPUID.0xD.16 = 716 cycles
CPUID.0xD.17 = 748 cycles
CPUID.0xD.18 = 776 cycles
Note, updating runtime CPUID information multiple times per nested
transition is itself a flaw, especially since CPUID is a mandotory
intercept on both Intel and AMD. E.g. KVM doesn't need to ensure emulated
CPUID state is up-to-date while running L2. That flaw will be fixed in a
future patch, as deferring runtime CPUID updates is more subtle than it
appears at first glance, the benefits aren't super critical to have once
the XSAVE issue is resolved, and caching CPUID output is desirable even if
KVM's updates are deferred.
Cc: Jim Mattson <jmattson@google.com>
Cc: stable@vger.kernel.org
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-ID: <20241211013302.1347853-2-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 572af9f284669d31d9175122bbef9bc62cea8ded ]
fwnode_find_mii_timestamper() calls of_parse_phandle_with_fixed_args()
but does not decrement the refcount of the obtained OF node. Add an
of_node_put() call before returning from the function.
This bug was detected by an experimental static analysis tool that I am
developing.
Fixes: bc1bee3b87 ("net: mdiobus: Introduce fwnode_mdiobus_register_phy()")
Signed-off-by: Joe Hattori <joe@pf.is.s.u-tokyo.ac.jp>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20241218035106.1436405-1-joe@pf.is.s.u-tokyo.ac.jp
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 70b6f46a4ed8bd56c85ffff22df91e20e8c85e33 ]
With CONFIG_PROVE_LOCKING, when creating a set of type bitmap:ip, adding
it to a set of type list:set and populating it from iptables SET target
triggers a kernel warning:
| WARNING: possible recursive locking detected
| 6.12.0-rc7-01692-g5e9a28f41134-dirty #594 Not tainted
| --------------------------------------------
| ping/4018 is trying to acquire lock:
| ffff8881094a6848 (&set->lock){+.-.}-{2:2}, at: ip_set_add+0x28c/0x360 [ip_set]
|
| but task is already holding lock:
| ffff88811034c048 (&set->lock){+.-.}-{2:2}, at: ip_set_add+0x28c/0x360 [ip_set]
This is a false alarm: ipset does not allow nested list:set type, so the
loop in list_set_kadd() can never encounter the outer set itself. No
other set type supports embedded sets, so this is the only case to
consider.
To avoid the false report, create a distinct lock class for list:set
type ipset locks.
Fixes: f830837f0e ("netfilter: ipset: list:set set type support")
Signed-off-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0cb2c504d79e7caa3abade3f466750c82ad26f01 ]
The OF node obtained by of_parse_phandle() is not freed. Call
of_node_put() to balance the refcount.
This bug was found by an experimental static analysis tool that I am
developing.
Fixes: 1676aba5ef ("net: ethernet: bgmac: device tree phy enablement")
Signed-off-by: Joe Hattori <joe@pf.is.s.u-tokyo.ac.jp>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20241214014912.2810315-1-joe@pf.is.s.u-tokyo.ac.jp
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7203d10e93b6e6e1d19481ef7907de6a9133a467 ]
There is a check for NULL at the start of create_txqs() and
create_rxqs() which tess if "nic_dev->txqs" is non-NULL. The
intention is that if the device is already open and the queues
are already created then we don't create them a second time.
However, the bug is that if we have an error in the create_txqs()
then the pointer doesn't get set back to NULL. The NULL check
at the start of the function will say that it's already open when
it's not and the device can't be used.
Set ->txqs back to NULL on cleanup on error.
Fixes: c3e79baf1b ("net-next/hinic: Add logical Txq and Rxq")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/0cc98faf-a0ed-4565-a55b-0fa2734bc205@stanley.mountain
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2d5df3a680ffdaf606baa10636bdb1daf757832e ]
Packets injected by the CPU should have a SRC_PORT field equal to the
CPU port module index in the Analyzer block (ocelot->num_phys_ports).
The blamed commit copied the ocelot_ifh_set_basic() call incorrectly
from ocelot_xmit_common() in net/dsa/tag_ocelot.c. Instead of calling
with "x", it calls with BIT_ULL(x), but the field is not a port mask,
but rather a single port index.
[ side note: this is the technical debt of code duplication :( ]
The error used to be silent and doesn't appear to have other
user-visible manifestations, but with new changes in the packing
library, it now fails loudly as follows:
------------[ cut here ]------------
Cannot store 0x40 inside bits 46-43 - will truncate
sja1105 spi2.0: xmit timed out
WARNING: CPU: 1 PID: 102 at lib/packing.c:98 __pack+0x90/0x198
sja1105 spi2.0: timed out polling for tstamp
CPU: 1 UID: 0 PID: 102 Comm: felix_xmit
Tainted: G W N 6.13.0-rc1-00372-gf706b85d972d-dirty #2605
Call trace:
__pack+0x90/0x198 (P)
__pack+0x90/0x198 (L)
packing+0x78/0x98
ocelot_ifh_set_basic+0x260/0x368
ocelot_port_inject_frame+0xa8/0x250
felix_port_deferred_xmit+0x14c/0x258
kthread_worker_fn+0x134/0x350
kthread+0x114/0x138
The code path pertains to the ocelot switchdev driver and to the felix
secondary DSA tag protocol, ocelot-8021q. Here seen with ocelot-8021q.
The messenger (packing) is not really to blame, so fix the original
commit instead.
Fixes: e1b9e80236c5 ("net: mscc: ocelot: fix QoS class for injected packets with "ocelot-8021q"")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20241212165546.879567-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c5b8ee5022a19464783058dc6042e8eefa34e8cd ]
When receiving clc msg, the field length in smc_clc_msg_hdr indicates the
length of msg should be received from network and the value should not be
fully trusted as it is from the network. Once the value of length exceeds
the value of buflen in function smc_clc_wait_msg it may run into deadloop
when trying to drain the remaining data exceeding buflen.
This patch checks the return value of sock_recvmsg when draining data in
case of deadloop in draining.
Fixes: fb4f79264c ("net/smc: tolerate future SMCD versions")
Signed-off-by: Guangguan Wang <guangguan.wang@linux.alibaba.com>
Reviewed-by: Wen Gu <guwen@linux.alibaba.com>
Reviewed-by: D. Wythe <alibuda@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9ab332deb671d8f7e66d82a2ff2b3f715bc3a4ad ]
When receiving proposal msg in server, the field smcd_v2_ext_offset in
proposal msg is from the remote client and can not be fully trusted.
Once the value of smcd_v2_ext_offset exceed the max value, there has
the chance to access wrong address, and crash may happen.
This patch checks the value of smcd_v2_ext_offset before using it.
Fixes: 5c21c4ccaf ("net/smc: determine accepted ISM devices")
Signed-off-by: Guangguan Wang <guangguan.wang@linux.alibaba.com>
Reviewed-by: Wen Gu <guwen@linux.alibaba.com>
Reviewed-by: D. Wythe <alibuda@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a29e220d3c8edbf0e1beb0f028878a4a85966556 ]
When receiving proposal msg in server, the field iparea_offset
and the field ipv6_prefixes_cnt in proposal msg are from the
remote client and can not be fully trusted. Especially the
field iparea_offset, once exceed the max value, there has the
chance to access wrong address, and crash may happen.
This patch checks iparea_offset and ipv6_prefixes_cnt before using them.
Fixes: e7b7a64a84 ("smc: support variable CLC proposal messages")
Signed-off-by: Guangguan Wang <guangguan.wang@linux.alibaba.com>
Reviewed-by: Wen Gu <guwen@linux.alibaba.com>
Reviewed-by: D. Wythe <alibuda@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 679e9ddcf90dbdf98aaaa71a492454654b627bcb ]
When application sending data more than sndbuf_space, there have chances
application will sleep in epoll_wait, and will never be wakeup again. This
is caused by a race between smc_poll and smc_cdc_tx_handler.
application tasklet
smc_tx_sendmsg(len > sndbuf_space) |
epoll_wait for EPOLL_OUT,timeout=0 |
smc_poll |
if (!smc->conn.sndbuf_space) |
| smc_cdc_tx_handler
| atomic_add sndbuf_space
| smc_tx_sndbuf_nonfull
| if (!test_bit SOCK_NOSPACE)
| do not sk_write_space;
set_bit SOCK_NOSPACE; |
return mask=0; |
Application will sleep in epoll_wait as smc_poll returns 0. And
smc_cdc_tx_handler will not call sk_write_space because the SOCK_NOSPACE
has not be set. If there is no inflight cdc msg, sk_write_space will not be
called any more, and application will sleep in epoll_wait forever.
So check sndbuf_space again after NOSPACE flag is set to break the race.
Fixes: 8dce2786a2 ("net/smc: smc_poll improvements")
Signed-off-by: Guangguan Wang <guangguan.wang@linux.alibaba.com>
Suggested-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2b33eb8f1b3e8c2f87cfdbc8cc117f6bdfabc6ec ]
link down work may be scheduled before lgr freed but execute
after lgr freed, which may result in crash. So it is need to
hold a reference before shedule link down work, and put the
reference after work executed or canceled.
The relevant crash call stack as follows:
list_del corruption. prev->next should be ffffb638c9c0fe20,
but was 0000000000000000
------------[ cut here ]------------
kernel BUG at lib/list_debug.c:51!
invalid opcode: 0000 [#1] SMP NOPTI
CPU: 6 PID: 978112 Comm: kworker/6:119 Kdump: loaded Tainted: G #1
Hardware name: Alibaba Cloud Alibaba Cloud ECS, BIOS 2221b89 04/01/2014
Workqueue: events smc_link_down_work [smc]
RIP: 0010:__list_del_entry_valid.cold+0x31/0x47
RSP: 0018:ffffb638c9c0fdd8 EFLAGS: 00010086
RAX: 0000000000000054 RBX: ffff942fb75e5128 RCX: 0000000000000000
RDX: ffff943520930aa0 RSI: ffff94352091fc80 RDI: ffff94352091fc80
RBP: 0000000000000000 R08: 0000000000000000 R09: ffffb638c9c0fc38
R10: ffffb638c9c0fc30 R11: ffffffffa015eb28 R12: 0000000000000002
R13: ffffb638c9c0fe20 R14: 0000000000000001 R15: ffff942f9cd051c0
FS: 0000000000000000(0000) GS:ffff943520900000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007f4f25214000 CR3: 000000025fbae004 CR4: 00000000007706e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
PKRU: 55555554
Call Trace:
rwsem_down_write_slowpath+0x17e/0x470
smc_link_down_work+0x3c/0x60 [smc]
process_one_work+0x1ac/0x350
worker_thread+0x49/0x2f0
? rescuer_thread+0x360/0x360
kthread+0x118/0x140
? __kthread_bind_mask+0x60/0x60
ret_from_fork+0x1f/0x30
Fixes: 541afa10c1 ("net/smc: add smcr_port_err() and smcr_link_down() processing")
Signed-off-by: Guangguan Wang <guangguan.wang@linux.alibaba.com>
Reviewed-by: Tony Lu <tonylu@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7363f2d4c18557c99c536b70489187bb4e05c412 ]
Since commit f63b94be6942 ("i2c: pnx: Fix potential deadlock warning
from del_timer_sync() call in isr") jiffies are stored in
i2c_pnx_algo_data.timeout, but wait_timeout and wait_reset are still
using it as milliseconds. Convert jiffies back to milliseconds to wait
for the expected amount of time.
Fixes: f63b94be6942 ("i2c: pnx: Fix potential deadlock warning from del_timer_sync() call in isr")
Signed-off-by: Vladimir Riabchun <ferr.lambarginio@gmail.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 360c400d0f568636c1b98d1d5f9f49aa3d420c70 ]
When drivers access P2SB device resources, it calls p2sb_bar(). Before
the commit 5913320eb0b3 ("platform/x86: p2sb: Allow p2sb_bar() calls
during PCI device probe"), p2sb_bar() obtained the resources and then
called pci_stop_and_remove_bus_device() for clean up. Then the P2SB
device disappeared. The commit 5913320eb0b3 introduced the P2SB device
resource cache feature in the boot process. During the resource cache,
pci_stop_and_remove_bus_device() is called for the P2SB device, then the
P2SB device disappears regardless of whether p2sb_bar() is called or
not. Such P2SB device disappearance caused a confusion [1]. To avoid the
confusion, avoid the pci_stop_and_remove_bus_device() call when the BIOS
does not hide the P2SB device.
For that purpose, cache the P2SB device resources only if the BIOS hides
the P2SB device. Call p2sb_scan_and_cache() only if p2sb_hidden_by_bios
is true. This allows removing two branches from p2sb_scan_and_cache().
When p2sb_bar() is called, get the resources from the cache if the P2SB
device is hidden. Otherwise, read the resources from the unhidden P2SB
device.
Reported-by: Daniel Walker (danielwa) <danielwa@cisco.com>
Closes: https://lore.kernel.org/lkml/ZzTI+biIUTvFT6NC@goliath/ [1]
Fixes: 5913320eb0b3 ("platform/x86: p2sb: Allow p2sb_bar() calls during PCI device probe")
Signed-off-by: Shin'ichiro Kawasaki <shinichiro.kawasaki@wdc.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20241128002836.373745-5-shinichiro.kawasaki@wdc.com
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1134289b6b93d73721340b66c310fd985385e8fa ]
When using dma_map_sg() to map the scatterlist with iommu enabled,
the entries in the scatterlist can be mergerd into less but longer
entries in the function __finalise_sg(). So that the number of
valid mapped entries is actually smaller than ureq->num_reqs,and
there are still some invalid entries in the scatterlist with
dma_addr=0xffffffff and len=0. Writing these invalid sg entries
into the dma_desc can cause a data transmission error.
The function dma_map_sg() returns the number of valid map entries
and the return value is assigned to usb_request::num_mapped_sgs in
function usb_gadget_map_request_by_dev(). So that just write valid
mapped entries into dma_desc according to the usb_request::num_mapped_sgs,
and set the IOC bit if it's the last valid mapped entry.
This patch poses no risk to no-iommu situation, cause
ureq->num_mapped_sgs equals ureq->num_sgs while using dma_direct_map_sg()
to map the scatterlist whith iommu disabled.
Signed-off-by: Peng Hongchi <hongchi.peng@siengine.com>
Link: https://lore.kernel.org/r/20240523100315.7226-1-hongchi.peng@siengine.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 524e057b2d66b61f9b63b6db30467ab7b0bb4796 ]
The Broadcom BCM5760X NIC may be a multi-function device.
While it does not advertise an ACS capability, peer-to-peer transactions
are not possible between the individual functions. So it is ok to treat
them as fully isolated.
Add an ACS quirk for this device so the functions can be in independent
IOMMU groups and attached individually to userspace applications using
VFIO.
[kwilczynski: commit log]
Link: https://lore.kernel.org/linux-pci/20240510204228.73435-1-ajit.khaparde@broadcom.com
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f24c9bfcd423e2b2bb0d198456412f614ec2030a ]
The vmd driver creates a "domain" symlink in sysfs for each VMD bridge.
Previously this symlink was created after pci_bus_add_devices() added
devices below the VMD bridge and emitted udev events to announce them to
userspace.
This led to a race between userspace consumers of the udev events and the
kernel creation of the symlink. One such consumer is mdadm, which
assembles block devices into a RAID array, and for devices below a VMD
bridge, mdadm depends on the "domain" symlink.
If mdadm loses the race, it may be unable to assemble a RAID array, which
may cause a boot failure or other issues, with complaints like this:
(udev-worker)[2149]: nvme1n1: '/sbin/mdadm -I /dev/nvme1n1'(err) 'mdadm: Unable to get real path for '/sys/bus/pci/drivers/vmd/0000:c7:00.5/domain/device''
(udev-worker)[2149]: nvme1n1: '/sbin/mdadm -I /dev/nvme1n1'(err) 'mdadm: /dev/nvme1n1 is not attached to Intel(R) RAID controller.'
(udev-worker)[2149]: nvme1n1: '/sbin/mdadm -I /dev/nvme1n1'(err) 'mdadm: No OROM/EFI properties for /dev/nvme1n1'
(udev-worker)[2149]: nvme1n1: '/sbin/mdadm -I /dev/nvme1n1'(err) 'mdadm: no RAID superblock on /dev/nvme1n1.'
(udev-worker)[2149]: nvme1n1: Process '/sbin/mdadm -I /dev/nvme1n1' failed with exit code 1.
This symptom prevents the OS from booting successfully.
After a NVMe disk is probed/added by the nvme driver, udevd invokes mdadm
to detect if there is a mdraid associated with this NVMe disk, and mdadm
determines if a NVMe device is connected to a particular VMD domain by
checking the "domain" symlink. For example:
Thread A Thread B Thread mdadm
vmd_enable_domain
pci_bus_add_devices
__driver_probe_device
...
work_on_cpu
schedule_work_on
: wakeup Thread B
nvme_probe
: wakeup scan_work
to scan nvme disk
and add nvme disk
then wakeup udevd
: udevd executes
mdadm command
flush_work main
: wait for nvme_probe done ...
__driver_probe_device find_driver_devices
: probe next nvme device : 1) Detect domain symlink
... 2) Find domain symlink
... from vmd sysfs
... 3) Domain symlink not
... created yet; failed
sysfs_create_link
: create domain symlink
Create the VMD "domain" symlink before invoking pci_bus_add_devices() to
avoid this race.
Suggested-by: Adrian Huang <ahuang12@lenovo.com>
Link: https://lore.kernel.org/linux-pci/20240605124844.24293-1-sjiwei@163.com
Signed-off-by: Jiwei Sun <sunjw10@lenovo.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
[bhelgaas: commit log]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Nirmal Patel <nirmal.patel@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7246a4520b4bf1494d7d030166a11b5226f6d508 ]
Use preserve_config in place of checking for PCI_PROBE_ONLY flag to enable
support for "linux,pci-probe-only" on a per host bridge basis.
This also obviates the use of adding PCI_REASSIGN_ALL_BUS flag if
!PCI_PROBE_ONLY, as pci_assign_unassigned_root_bus_resources() takes care
of reassigning the resources that are not already claimed.
Link: https://lore.kernel.org/r/20240508174138.3630283-5-vidyas@nvidia.com
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 5eb7de8cd58e73851cd37ff8d0666517d9926948 upstream.
Changes to sch->q.qlen around qdisc_tree_reduce_backlog() need to happen
_before_ a call to said function because otherwise it may fail to notify
parent qdiscs when the child is about to become empty.
Signed-off-by: Lion Ackermann <nnamrec@gmail.com>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cc: Artem Metla <ametla@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 349f0086ba8b2a169877d21ff15a4d9da3a60054 upstream.
In 32-bit x86 builds CONFIG_STATIC_CALL_INLINE isn't set, leading to
static_call_initialized not being available.
Define it as "0" in that case.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Fixes: 0ef8047b737d ("x86/static-call: provide a way to do very early static-call updates")
Signed-off-by: Juergen Gross <jgross@suse.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f7d306b47a24367302bd4fe846854e07752ffcd9 upstream.
The usb_get_descriptor() function does DMA so we're not allowed
to use a stack buffer for that. Doing DMA to the stack is not portable
all architectures. Move the "new_device_descriptor" from being stored
on the stack and allocate it with kmalloc() instead.
Fixes: b909df18ce2a ("ALSA: usb-audio: Fix potential out-of-bound accesses for Extigy and Mbox devices")
Cc: stable@kernel.org
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Link: https://patch.msgid.link/60e3aa09-039d-46d2-934c-6f123026c2eb@stanley.mountain
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Benoît Sevens <bsevens@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7fa0da5373685e7ed249af3fa317ab1e1ba8b0a6 upstream.
The hypercall page is no longer needed. It can be removed, as from the
Xen perspective it is optional.
But, from Linux's perspective, it removes naked RET instructions that
escape the speculative protections that Call Depth Tracking and/or
Untrain Ret are trying to achieve.
This is part of XSA-466 / CVE-2024-53241.
Reported-by: Andrew Cooper <andrew.cooper3@citrix.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Andrew Cooper <andrew.cooper3@citrix.com>
Reviewed-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b1c2cb86f4a7861480ad54bb9a58df3cbebf8e92 upstream.
Call the Xen hypervisor via the new xen_hypercall_func static-call
instead of the hypercall page.
This is part of XSA-466 / CVE-2024-53241.
Reported-by: Andrew Cooper <andrew.cooper3@citrix.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Co-developed-by: Peter Zijlstra <peterz@infradead.org>
Co-developed-by: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b4845bb6383821a9516ce30af3a27dc873e37fd4 upstream.
Add generic hypercall functions usable for all normal (i.e. not iret)
hypercalls. Depending on the guest type and the processor vendor
different functions need to be used due to the to be used instruction
for entering the hypervisor:
- PV guests need to use syscall
- HVM/PVH guests on Intel need to use vmcall
- HVM/PVH guests on AMD and Hygon need to use vmmcall
As PVH guests need to issue hypercalls very early during boot, there
is a 4th hypercall function needed for HVM/PVH which can be used on
Intel and AMD processors. It will check the vendor type and then set
the Intel or AMD specific function to use via static_call().
This is part of XSA-466 / CVE-2024-53241.
Reported-by: Andrew Cooper <andrew.cooper3@citrix.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Co-developed-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a2796dff62d6c6bfc5fbebdf2bee0d5ac0438906 upstream.
Instead of jumping to the Xen hypercall page for doing the iret
hypercall, directly code the required sequence in xen-asm.S.
This is done in preparation of no longer using hypercall page at all,
as it has shown to cause problems with speculation mitigations.
This is part of XSA-466 / CVE-2024-53241.
Reported-by: Andrew Cooper <andrew.cooper3@citrix.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0ef8047b737d7480a5d4c46d956e97c190f13050 upstream.
Add static_call_update_early() for updating static-call targets in
very early boot.
This will be needed for support of Xen guest type specific hypercall
functions.
This is part of XSA-466 / CVE-2024-53241.
Reported-by: Andrew Cooper <andrew.cooper3@citrix.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Co-developed-by: Peter Zijlstra <peterz@infradead.org>
Co-developed-by: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dda014ba59331dee4f3b773a020e109932f4bd24 upstream.
The syscall instruction is used in Xen PV mode for doing hypercalls.
Allow syscall to be used in the kernel in case it is tagged with an
unwind hint for objtool.
This is part of XSA-466 / CVE-2024-53241.
Reported-by: Andrew Cooper <andrew.cooper3@citrix.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Co-developed-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit efbcd61d9bebb771c836a3b8bfced8165633db7c upstream.
In order to be able to differentiate between AMD and Intel based
systems for very early hypercalls without having to rely on the Xen
hypercall page, make get_cpu_vendor() non-static.
Refactor early_cpu_init() for the same reason by splitting out the
loop initializing cpu_devs() into an externally callable function.
This is part of XSA-466 / CVE-2024-53241.
Reported-by: Andrew Cooper <andrew.cooper3@citrix.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f9244fb55f37356f75c739c57323d9422d7aa0f8 upstream.
When removing a netfront device directly after a suspend/resume cycle
it might happen that the queues have not been setup again, causing a
crash during the attempt to stop the queues another time.
Fix that by checking the queues are existing before trying to stop
them.
This is XSA-465 / CVE-2024-53240.
Reported-by: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com>
Fixes: d50b7914fa ("xen-netfront: Fix NULL sring after live migration")
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b022f0c7e4 ("tracing/kprobes: Return EADDRNOTAVAIL when func matches several symbols")
avoids checking number_of_same_symbols() for module symbol in
__trace_kprobe_create(), but create_local_trace_kprobe() should avoid this
check too. Doing this check leads to ENOENT for module_name:symbol_name
constructions passed over perf_event_open.
No bug in newer kernels as it was fixed more generally by
commit 9d8616034f16 ("tracing/kprobes: Add symbol counting check when module loads")
Link: https://lore.kernel.org/linux-trace-kernel/20240705161030.b3ddb33a8167013b9b1da202@kernel.org
Fixes: b022f0c7e4 ("tracing/kprobes: Return EADDRNOTAVAIL when func matches several symbols")
Signed-off-by: Nikolay Kuratov <kniv@yandex-team.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e9bd9c498cb0f5843996dbe5cbce7a1836a83c70 upstream.
Range propagation must not affect subreg_def marks, otherwise the
following example is rewritten by verifier incorrectly when
BPF_F_TEST_RND_HI32 flag is set:
0: call bpf_ktime_get_ns call bpf_ktime_get_ns
1: r0 &= 0x7fffffff after verifier r0 &= 0x7fffffff
2: w1 = w0 rewrites w1 = w0
3: if w0 < 10 goto +0 --------------> r11 = 0x2f5674a6 (r)
4: r1 >>= 32 r11 <<= 32 (r)
5: r0 = r1 r1 |= r11 (r)
6: exit; if w0 < 0xa goto pc+0
r1 >>= 32
r0 = r1
exit
(or zero extension of w1 at (2) is missing for architectures that
require zero extension for upper register half).
The following happens w/o this patch:
- r0 is marked as not a subreg at (0);
- w1 is marked as subreg at (2);
- w1 subreg_def is overridden at (3) by copy_register_state();
- w1 is read at (5) but mark_insn_zext() does not mark (2)
for zero extension, because w1 subreg_def is not set;
- because of BPF_F_TEST_RND_HI32 flag verifier inserts random
value for hi32 bits of (2) (marked (r));
- this random value is read at (5).
Fixes: 75748837b7 ("bpf: Propagate scalar ranges through register assignments.")
Reported-by: Lonial Con <kongln9170@gmail.com>
Signed-off-by: Lonial Con <kongln9170@gmail.com>
Signed-off-by: Eduard Zingerman <eddyz87@gmail.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Closes: https://lore.kernel.org/bpf/7e2aa30a62d740db182c170fdd8f81c596df280d.camel@gmail.com
Link: https://lore.kernel.org/bpf/20240924210844.1758441-1-eddyz87@gmail.com
[ shung-hsi.yu: sync_linked_regs() was called find_equal_scalars() before commit
4bf79f9be434 ("bpf: Track equal scalars history on per-instruction level"), and
modification is done because there is only a single call to
copy_register_state() before commit 98d7ca374ba4 ("bpf: Track delta between
"linked" registers."). ]
Signed-off-by: Shung-Hsi Yu <shung-hsi.yu@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 57e420c84f9ab55ba4c5e2ae9c5f6c8e1ea834d2 ]
After a recent change to clamp() and its variants [1] that increases the
coverage of the check that high is greater than low because it can be
done through inlining, certain build configurations (such as s390
defconfig) fail to build with clang with:
block/blk-iocost.c:1101:11: error: call to '__compiletime_assert_557' declared with 'error' attribute: clamp() low limit 1 greater than high limit active
1101 | inuse = clamp_t(u32, inuse, 1, active);
| ^
include/linux/minmax.h:218:36: note: expanded from macro 'clamp_t'
218 | #define clamp_t(type, val, lo, hi) __careful_clamp(type, val, lo, hi)
| ^
include/linux/minmax.h:195:2: note: expanded from macro '__careful_clamp'
195 | __clamp_once(type, val, lo, hi, __UNIQUE_ID(v_), __UNIQUE_ID(l_), __UNIQUE_ID(h_))
| ^
include/linux/minmax.h:188:2: note: expanded from macro '__clamp_once'
188 | BUILD_BUG_ON_MSG(statically_true(ulo > uhi), \
| ^
__propagate_weights() is called with an active value of zero in
ioc_check_iocgs(), which results in the high value being less than the
low value, which is undefined because the value returned depends on the
order of the comparisons.
The purpose of this expression is to ensure inuse is not more than
active and at least 1. This could be written more simply with a ternary
expression that uses min(inuse, active) as the condition so that the
value of that condition can be used if it is not zero and one if it is.
Do this conversion to resolve the error and add a comment to deter
people from turning this back into clamp().
Fixes: 7caa47151a ("blkcg: implement blk-iocost")
Link: https://lore.kernel.org/r/34d53778977747f19cce2abb287bb3e6@AcuMS.aculab.com/ [1]
Suggested-by: David Laight <david.laight@aculab.com>
Reported-by: Linux Kernel Functional Testing <lkft@linaro.org>
Closes: https://lore.kernel.org/llvm/CA+G9fYsD7mw13wredcZn0L-KBA3yeoVSTuxnss-AEWMN3ha0cA@mail.gmail.com/
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202412120322.3GfVe3vF-lkp@intel.com/
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 29a651451e6c264f58cd9d9a26088e579d17b242 ]
The voice setting is used by sco_connect() or sco_conn_defer_accept()
after being set by sco_sock_setsockopt().
The PCM part of the voice setting is used for offload mode through PCM
chipset port.
This commits add support for mSBC 16 bits offloading, i.e. audio data
not transported over HCI.
The BCM4349B1 supports 16 bits transparent data on its I2S port.
If BT_VOICE_TRANSPARENT is used when accepting a SCO connection, this
gives only garbage audio while using BT_VOICE_TRANSPARENT_16BIT gives
correct audio.
This has been tested with connection to iPhone 14 and Samsung S24.
Fixes: ad10b1a487 ("Bluetooth: Add Bluetooth socket voice option")
Signed-off-by: Frédéric Danis <frederic.danis@collabora.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
