commit fd39d9668f upstream.
The ms5611 driver falsely rejects lots of MS5607-02BA03-50 chips
with "PROM integrity check failed" because it doesn't accept a prom crc
value of zero as legitimate.
According to the datasheet for this chip (and the manufacturer's
application note about the PROM CRC), none of the possible values for the
CRC are excluded - but the current code in ms5611_prom_is_valid() ends with
return crc_orig != 0x0000 && crc == crc_orig
Discussed with the driver author (Tomasz Duszynski) and he indicated that
at that time (2015) he was dealing with some faulty chip samples which
returned blank data under some circumstances and/or followed example code
which indicated CRC zero being bad.
As far as I can tell this exception should not be applied anymore; We've
got a few hundred custom boards here with this chip where large numbers
of the prom have a legitimate CRC value 0, and do work fine, but which the
current driver code wrongly rejects.
Signed-off-by: Alexander Zangerl <az@breathe-safe.com>
Fixes: c0644160a8 ("iio: pressure: add support for MS5611 pressure and temperature sensor")
Link: https://lore.kernel.org/r/2535-1695168070.831792@Ze3y.dhYT.s3fx
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 901a293fd9 upstream.
The DPS310 sensor chip has been encountering intermittent errors while
reading the sensor device across various system designs. This issue causes
the chip to become "stuck," preventing the indication of "ready" status
for pressure and temperature measurements in the MEAS_CFG register.
To address this issue, this commit fixes the timeout settings to improve
sensor stability:
- After sending a reset command to the chip, the timeout has been extended
from 2.5 ms to 15 ms, aligning with the DPS310 specification.
- The read timeout value of the MEAS_CFG register has been adjusted from
20ms to 30ms to match the specification.
Signed-off-by: Lakshmi Yadlapati <lakshmiy@us.ibm.com>
Fixes: 7b4ab4abce ("iio: pressure: dps310: Reset chip after timeout")
Link: https://lore.kernel.org/r/20230829180222.3431926-2-lakshmiy@us.ibm.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 850101b359 upstream.
The ADC Command Buffer Register high and low are currently pointing to
the wrong address and makes it impossible to perform correct
ADC measurements over all channels.
According to the datasheet of the imx8qxp the ADC_CMDL register starts
at address 0x100 and the ADC_CMDH register starts at address 0x104.
This bug seems to be in the kernel since the introduction of this
driver.
This can be observed by checking all raw voltages of the adc and they
are all nearly identical:
cat /sys/bus/iio/devices/iio\:device0/in_voltage*_raw
3498
3494
3491
3491
3489
3490
3490
3490
Fixes: 1e23dcaa1a ("iio: imx8qxp-adc: Add driver support for NXP IMX8QXP ADC")
Signed-off-by: Philipp Rossak <embed3d@gmail.com>
Acked-by: Haibo Chen <haibo.chen@nxp.com>
Link: https://lore.kernel.org/r/20230904220204.23841-1-embed3d@gmail.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6658a62e1d upstream.
musb HWVers rgister address is not 0x69, if we operate the
wrong address 0x69, it will cause a kernel crash, because
there is no register corresponding to this address in the
additional control register of musb. In fact, HWVers has
been defined in musb_register.h, and the name is
"MUSB_HWVERS", so We need to use this macro instead of 0x69.
Fixes: c2365ce5d5 ("usb: musb: replace hard coded registers with defines")
Cc: stable@vger.kernel.org
Signed-off-by: Xingxing Luo <xingxing.luo@unisoc.com>
Link: https://lore.kernel.org/r/20230922075929.31074-1-xingxing.luo@unisoc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 33d7e37232 upstream.
When multiple threads are performing USB transmission, musb->lock will be
unlocked when musb_giveback is executed. At this time, qh may be released
in the dequeue process in other threads, resulting in a wild pointer, so
it needs to be here get qh again, and judge whether qh is NULL, and when
dequeue, you need to set qh to NULL.
Fixes: dbac5d07d1 ("usb: musb: host: don't start next rx urb if current one failed")
Cc: stable@vger.kernel.org
Signed-off-by: Xingxing Luo <xingxing.luo@unisoc.com>
Link: https://lore.kernel.org/r/20230919033055.14085-1-xingxing.luo@unisoc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 41a43013d2 upstream.
As mentioned in:
commit 474ed23a62 ("xhci: align the last trb before link if it is
easily splittable.")
A bounce buffer is utilized for ensuring that transfers that span across
ring segments are aligned to the EP's max packet size. However, the device
that is used to map the DMA buffer to is currently using the XHCI HCD,
which does not carry any DMA operations in certain configrations.
Migration to using the sysdev entry was introduced for DWC3 based
implementations where the IOMMU operations are present.
Replace the reference to the controller device to sysdev instead. This
allows the bounce buffer to be properly mapped to any implementations that
have an IOMMU involved.
cc: stable@vger.kernel.org
Fixes: 4c39d4b949 ("usb: xhci: use bus->sysdev for DMA configuration")
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20230915143108.1532163-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5849704217 upstream.
CRQA flag is set by hardware when the channel request become active and
the channel is enabled. It is cleared by hardware, when the channel request
is completed.
So when it is set, it means MDMA is transferring bytes.
This information is useful in case of STM32 DMA and MDMA chaining,
especially when the user pauses DMA before stopping it, to trig one last
MDMA transfer to get the latest bytes of the SRAM buffer to the
destination buffer.
STM32 DCMI driver can then use this to know if the last MDMA transfer in
case of chaining is done.
Fixes: 6968743227 ("dmaengine: stm32-mdma: add support to be triggered by STM32 DMA")
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20231004163531.2864160-3-amelie.delaunay@foss.st.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a4b306eb83 upstream.
Current implementation relies on curr_hwdesc index. But to keep this index
up to date, Block Transfer interrupt (BTIE) has to be enabled.
If it is not, curr_hwdesc is not updated, and then residue is not reliable.
Rely on Link Address Register instead. And disable BTIE interrupt
in stm32_mdma_setup_xfer() because it is no more needed in case of
_prep_slave_sg() to maintain curr_hwdesc up to date.
It avoids extra interrupts and also ensures a reliable residue. These
improvements are required for STM32 DCMI camera capture use case, which
need STM32 DMA and MDMA chaining for good performance.
Fixes: 6968743227 ("dmaengine: stm32-mdma: add support to be triggered by STM32 DMA")
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20231004163531.2864160-2-amelie.delaunay@foss.st.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 67e13e8974 upstream.
In case of MDMA chaining, DMA is configured in Double-Buffer Mode (DBM)
with two periods, but if transfer has been prepared with _prep_slave_sg(),
the transfer is not marked cyclic (=!chan->desc->cyclic). However, as DBM
is activated for MDMA chaining, residue computation must take into account
cyclic constraints.
With only two periods in MDMA chaining, and no update due to Transfer
Complete interrupt masked, n_sg is always 0. If DMA current memory address
(depending on SxCR.CT and SxM0AR/SxM1AR) does not correspond, it means n_sg
should be increased.
Then, the residue of the current period is the one read from SxNDTR and
should not be overwritten with the full period length.
Fixes: 723795173c ("dmaengine: stm32-dma: add support to trigger STM32 MDMA")
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20231004155024.2609531-2-amelie.delaunay@foss.st.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b650d953cd ]
Under certain circumstances, the tcp receive buffer memory limit
set by autotuning (sk_rcvbuf) is increased due to incoming data
packets as a result of the window not closing when it should be.
This can result in the receive buffer growing all the way up to
tcp_rmem[2], even for tcp sessions with a low BDP.
To reproduce: Connect a TCP session with the receiver doing
nothing and the sender sending small packets (an infinite loop
of socket send() with 4 bytes of payload with a sleep of 1 ms
in between each send()). This will cause the tcp receive buffer
to grow all the way up to tcp_rmem[2].
As a result, a host can have individual tcp sessions with receive
buffers of size tcp_rmem[2], and the host itself can reach tcp_mem
limits, causing the host to go into tcp memory pressure mode.
The fundamental issue is the relationship between the granularity
of the window scaling factor and the number of byte ACKed back
to the sender. This problem has previously been identified in
RFC 7323, appendix F [1].
The Linux kernel currently adheres to never shrinking the window.
In addition to the overallocation of memory mentioned above, the
current behavior is functionally incorrect, because once tcp_rmem[2]
is reached when no remediations remain (i.e. tcp collapse fails to
free up any more memory and there are no packets to prune from the
out-of-order queue), the receiver will drop in-window packets
resulting in retransmissions and an eventual timeout of the tcp
session. A receive buffer full condition should instead result
in a zero window and an indefinite wait.
In practice, this problem is largely hidden for most flows. It
is not applicable to mice flows. Elephant flows can send data
fast enough to "overrun" the sk_rcvbuf limit (in a single ACK),
triggering a zero window.
But this problem does show up for other types of flows. Examples
are websockets and other type of flows that send small amounts of
data spaced apart slightly in time. In these cases, we directly
encounter the problem described in [1].
RFC 7323, section 2.4 [2], says there are instances when a retracted
window can be offered, and that TCP implementations MUST ensure
that they handle a shrinking window, as specified in RFC 1122,
section 4.2.2.16 [3]. All prior RFCs on the topic of tcp window
management have made clear that sender must accept a shrunk window
from the receiver, including RFC 793 [4] and RFC 1323 [5].
This patch implements the functionality to shrink the tcp window
when necessary to keep the right edge within the memory limit by
autotuning (sk_rcvbuf). This new functionality is enabled with
the new sysctl: net.ipv4.tcp_shrink_window
Additional information can be found at:
https://blog.cloudflare.com/unbounded-memory-usage-by-tcp-for-receive-buffers-and-how-we-fixed-it/
[1] https://www.rfc-editor.org/rfc/rfc7323#appendix-F
[2] https://www.rfc-editor.org/rfc/rfc7323#section-2.4
[3] https://www.rfc-editor.org/rfc/rfc1122#page-91
[4] https://www.rfc-editor.org/rfc/rfc793
[5] https://www.rfc-editor.org/rfc/rfc1323
Signed-off-by: Mike Freemon <mfreemon@cloudflare.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ca10d851b9 ]
Commit 5c0338c687 ("workqueue: restore WQ_UNBOUND/max_active==1
to be ordered") enabled implicit ordered attribute to be added to
WQ_UNBOUND workqueues with max_active of 1. This prevented the changing
of attributes to these workqueues leading to fix commit 0a94efb5ac
("workqueue: implicit ordered attribute should be overridable").
However, workqueue_apply_unbound_cpumask() was not updated at that time.
So sysfs changes to wq_unbound_cpumask has no effect on WQ_UNBOUND
workqueues with implicit ordered attribute. Since not all WQ_UNBOUND
workqueues are visible on sysfs, we are not able to make all the
necessary cpumask changes even if we iterates all the workqueue cpumasks
in sysfs and changing them one by one.
Fix this problem by applying the corresponding change made
to apply_workqueue_attrs_locked() in the fix commit to
workqueue_apply_unbound_cpumask().
Fixes: 5c0338c687 ("workqueue: restore WQ_UNBOUND/max_active==1 to be ordered")
Signed-off-by: Waiman Long <longman@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a950a5921d ]
SMC_STAT_PAYLOAD_SUB(_smc_stats, _tech, key, _len, _rc) will calculate
wrong bucket positions for payloads of exactly 4096 bytes and
(1 << (m + 12)) bytes, with m == SMC_BUF_MAX - 1.
Intended bucket distribution:
Assume l == size of payload, m == SMC_BUF_MAX - 1.
Bucket 0 : 0 < l <= 2^13
Bucket n, 1 <= n <= m-1 : 2^(n+12) < l <= 2^(n+13)
Bucket m : l > 2^(m+12)
Current solution:
_pos = fls64((l) >> 13)
[...]
_pos = (_pos < m) ? ((l == 1 << (_pos + 12)) ? _pos - 1 : _pos) : m
For l == 4096, _pos == -1, but should be _pos == 0.
For l == (1 << (m + 12)), _pos == m, but should be _pos == m - 1.
In order to avoid special treatment of these corner cases, the
calculation is adjusted. The new solution first subtracts the length by
one, and then calculates the correct bucket by shifting accordingly,
i.e. _pos = fls64((l - 1) >> 13), l > 0.
This not only fixes the issues named above, but also makes the whole
bucket assignment easier to follow.
Same is done for SMC_STAT_RMB_SIZE_SUB(_smc_stats, _tech, k, _len),
where the calculation of the bucket position is similar to the one
named above.
Fixes: e0e4b8fa53 ("net/smc: Add SMC statistics support")
Suggested-by: Halil Pasic <pasic@linux.ibm.com>
Signed-off-by: Nils Hoppmann <niho@linux.ibm.com>
Reviewed-by: Halil Pasic <pasic@linux.ibm.com>
Reviewed-by: Wenjia Zhang <wenjia@linux.ibm.com>
Reviewed-by: Dust Li <dust.li@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fde2f2d7f2 ]
When updating the SA, use the new update_pn flags instead of comparing the
new PN with the initial one.
Comparing the initial PN value with the new value will allow the user
to update the SA using the initial PN value as a parameter like this:
$ ip macsec add macsec0 tx sa 0 pn 1 on key 00 \
ead3664f508eb06c40ac7104cdae4ce5
$ ip macsec set macsec0 tx sa 0 pn 1 off
Fixes: 8ff0ac5be1 ("net/mlx5: Add MACsec offload Tx command support")
Fixes: aae3454e4d ("net/mlx5e: Add MACsec offload Rx command support")
Signed-off-by: Radu Pirea (NXP OSS) <radu-nicolae.pirea@oss.nxp.com>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e0a8c918da ]
Updating the PN is not supported.
Return -EINVAL if update_pn is true.
The following command succeeded, but it should fail because the driver
does not update the PN:
ip macsec set macsec0 tx sa 0 pn 232 on
Fixes: 28c5107aa9 ("net: phy: mscc: macsec support")
Signed-off-by: Radu Pirea (NXP OSS) <radu-nicolae.pirea@oss.nxp.com>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0412cc846a ]
Indicate next PN update using update_pn flag in macsec_context.
Offloaded MACsec implementations does not know whether or not the
MACSEC_SA_ATTR_PN attribute was passed for an SA update and assume
that next PN should always updated, but this is not always true.
The PN can be reset to its initial value using the following command:
$ ip macsec set macsec0 tx sa 0 off #octeontx2-pf case
Or, the update PN command will succeed even if the driver does not support
PN updates.
$ ip macsec set macsec0 tx sa 0 pn 1 on #mscc phy driver case
Comparing the initial PN with the new PN value is not a solution. When
the user updates the PN using its initial value the command will
succeed, even if the driver does not support it. Like this:
$ ip macsec add macsec0 tx sa 0 pn 1 on key 00 \
ead3664f508eb06c40ac7104cdae4ce5
$ ip macsec set macsec0 tx sa 0 pn 1 on #mlx5 case
Signed-off-by: Radu Pirea (NXP OSS) <radu-nicolae.pirea@oss.nxp.com>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Stable-dep-of: e0a8c918da ("net: phy: mscc: macsec: reject PN update requests")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 829955981c ]
The verifier, as part of check_return_code(), verifies that async
callbacks such as from e.g. timers, will return 0. It does this by
correctly checking that R0->var_off is in tnum_const(0), which
effectively checks that it's in a range of 0. If this condition fails,
however, it prints an error message which says that the value should
have been in (0x0; 0x1). This results in possibly confusing output such
as the following in which an async callback returns 1:
At async callback the register R0 has value (0x1; 0x0) should have been in (0x0; 0x1)
The fix is easy -- we should just pass the tnum_const(0) as the correct
range to verbose_invalid_scalar(), which will then print the following:
At async callback the register R0 has value (0x1; 0x0) should have been in (0x0; 0x0)
Fixes: bfc6bb74e4 ("bpf: Implement verifier support for validation of async callbacks.")
Signed-off-by: David Vernet <void@manifault.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20231009161414.235829-1-void@manifault.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2f1b0d3d73 ]
The RISC-V architecture does not expose sub-registers, and hold all
32-bit values in a sign-extended format [1] [2]:
| The compiler and calling convention maintain an invariant that all
| 32-bit values are held in a sign-extended format in 64-bit
| registers. Even 32-bit unsigned integers extend bit 31 into bits
| 63 through 32. Consequently, conversion between unsigned and
| signed 32-bit integers is a no-op, as is conversion from a signed
| 32-bit integer to a signed 64-bit integer.
While BPF, on the other hand, exposes sub-registers, and use
zero-extension (similar to arm64/x86).
This has led to some subtle bugs, where a BPF JITted program has not
sign-extended the a0 register (return value in RISC-V land), passed
the return value up the kernel, e.g.:
| int from_bpf(void);
|
| long foo(void)
| {
| return from_bpf();
| }
Here, a0 would be 0xffff_ffff, instead of the expected
0xffff_ffff_ffff_ffff.
Internally, the RISC-V JIT uses a5 as a dedicated register for BPF
return values.
Keep a5 zero-extended, but explicitly sign-extend a0 (which is used
outside BPF land). Now that a0 (RISC-V ABI) and a5 (BPF ABI) differs,
a0 is only moved to a5 for non-BPF native calls (BPF_PSEUDO_CALL).
Fixes: 2353ecc6f9 ("bpf, riscv: add BPF JIT for RV64G")
Signed-off-by: Björn Töpel <bjorn@rivosinc.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://github.com/riscv/riscv-isa-manual/releases/download/riscv-isa-release-056b6ff-2023-10-02/unpriv-isa-asciidoc.pdf # [2]
Link: https://github.com/riscv-non-isa/riscv-elf-psabi-doc/releases/download/draft-20230929-e5c800e661a53efe3c2678d71a306323b60eb13b/riscv-abi.pdf # [2]
Link: https://lore.kernel.org/bpf/20231004120706.52848-2-bjorn@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 66cf7435a2 ]
Do not set netback interfaces (vifs) default TX queue size to the ring size.
The TX queue size is not related to the ring size, and using the ring size (32)
as the queue size can lead to packet drops. Note the TX side of the vif
interface in the netback domain is the one receiving packets to be injected
to the guest.
Do not explicitly set the TX queue length to any value when creating the
interface, and instead use the system default. Note that the queue length can
also be adjusted at runtime.
Fixes: f942dc2552 ('xen network backend driver')
Signed-off-by: Roger Pau Monné <roger.pau@citrix.com>
Reviewed-by: Ross Lagerwall <ross.lagerwall@citrix.com>
Acked-by: Wei Liu <wei.liu@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1e0b72a2a6 ]
The mlxsw_sp2_nve_vxlan_learning_set() function is supposed to return
zero on success or negative error codes. So it needs to be type int
instead of bool.
Fixes: 4ee70efab6 ("mlxsw: spectrum_nve: Add support for VXLAN on Spectrum-2")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f990874b1c ]
If of_clk_add_provider() fails in ca8210_register_ext_clock(),
it calls clk_unregister() to release priv->clk and returns an
error. However, the caller ca8210_probe() then calls ca8210_remove(),
where priv->clk is freed again in ca8210_unregister_ext_clock(). In
this case, a use-after-free may happen in the second time we call
clk_unregister().
Fix this by removing the first clk_unregister(). Also, priv->clk could
be an error code on failure of clk_register_fixed_rate(). Use
IS_ERR_OR_NULL to catch this case in ca8210_unregister_ext_clock().
Fixes: ded845a781 ("ieee802154: Add CA8210 IEEE 802.15.4 device driver")
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Message-ID: <20231007033049.22353-1-dinghao.liu@zju.edu.cn>
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d192615c30 ]
The DSU PMU allows monitoring performance events in the DSU cluster,
which is done by configuring and reading back values from the DSU PMU
system registers. However, for write-access to be allowed by ELs lower
than EL3, the EL3 firmware needs to update the setting on the ACTLR3_EL3
register, as it is disallowed by default.
That configuration is not done on the firmware used by the MT8195 SoC,
as a consequence, booting a MT8195-based machine like
mt8195-cherry-tomato-r2 with CONFIG_ARM_DSU_PMU enabled hangs the kernel
just as it writes to the CLUSTERPMOVSCLR_EL1 register, since the
instruction faults to EL3, and BL31 apparently just re-runs the
instruction over and over.
Mark the DSU PMU node in the Devicetree with status "fail", as the
machine doesn't have a suitable firmware to make use of it from the
kernel, and allowing its driver to probe would hang the kernel.
Fixes: 37f2582883 ("arm64: dts: Add mediatek SoC mt8195 and evaluation board")
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230720200753.322133-1-nfraprado@collabora.com
Link: https://lore.kernel.org/r/20231003-mediatek-fixes-v6-7-v1-5-dad7cd62a8ff@collabora.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
