[ Upstream commit 7b1b7961170e4fcad488755e5ffaaaf9bd527e8f ]
Refuse to register a cpuidle device if the given CPU has a cpuidle
device already and print a message regarding it.
Without this, an attempt to register a new cpuidle device without
unregistering the existing one leads to the removal of the existing
cpuidle device without removing its sysfs interface.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5612ea8b554375d45c14cbb0f8ea93ec5d172891 ]
This fixes the build with -Werror -Wall.
btf_dumper.c:71:31: error: variable 'finfo' is uninitialized when passed as a const pointer argument here [-Werror,-Wuninitialized-const-pointer]
71 | info.func_info = ptr_to_u64(&finfo);
| ^~~~~
prog.c:2294:31: error: variable 'func_info' is uninitialized when passed as a const pointer argument here [-Werror,-Wuninitialized-const-pointer]
2294 | info.func_info = ptr_to_u64(&func_info);
|
v2:
- Initialize instead of using memset.
Signed-off-by: Tom Stellard <tstellar@redhat.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Acked-by: Quentin Monnet <qmo@kernel.org>
Link: https://lore.kernel.org/bpf/20250917183847.318163-1-tstellar@redhat.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 41307ec7df057239aae3d0f089cc35a0d735cdf8 ]
The X1E80100 battery management firmware sends a notification with
code 0x83 when the battery charging state changes, such as switching
between fast charge, taper charge, end of charge, or any other error
charging states.
The same notification code is used with bit[8] set when charging stops
because the charge control end threshold is reached. Additionally,
a 2-bit value is included in bit[10:9] with the same code to indicate
the charging source capability, which is determined by the calculated
power from voltage and current readings from PDOs: 2 means a strong
charger over 60W, 1 indicates a weak charger, and 0 means there is no
charging source.
These 3-MSB [10:8] in the notification code is not much useful for now,
hence just ignore them and trigger a power supply change event whenever
0x83 notification code is received. This helps to eliminate the unknown
notification error messages.
Reported-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Closes: https://lore.kernel.org/all/r65idyc4of5obo6untebw4iqfj2zteiggnnzabrqtlcinvtddx@xc4aig5abesu/
Signed-off-by: Fenglin Wu <fenglin.wu@oss.qualcomm.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 57b100d4cf14276e0340eecb561005c07c129eb8 ]
The cpupower_write_sysfs() function currently returns -1 on
write failure, but the function signature indicates it should
return an unsigned int. Returning -1 from an unsigned function
results in a large positive value rather than indicating
an error condition.
Fix this by returning 0 on failure, which is more appropriate
for an unsigned return type and maintains consistency with typical
success/failure semantics where 0 indicates failure and non-zero
indicates success (bytes written).
Link: https://lore.kernel.org/r/20250828063000.803229-1-kaushlendra.kumar@intel.com
Signed-off-by: Kaushlendra Kumar <kaushlendra.kumar@intel.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2c895133950646f45e5cf3900b168c952c8dbee8 ]
The bpf_cgroup_from_id kfunc relies on cgroup_get_from_id to obtain the
cgroup corresponding to a given cgroup ID. This helper can be called in
a lot of contexts where the current thread can be random. A recent
example was its use in sched_ext's ops.tick(), to obtain the root cgroup
pointer. Since the current task can be whatever random user space task
preempted by the timer tick, this makes the behavior of the helper
unreliable.
Refactor out __cgroup_get_from_id as the non-namespace aware version of
cgroup_get_from_id, and change bpf_cgroup_from_id to make use of it.
There is no compatibility breakage here, since changing the namespace
against which the lookup is being done to the root cgroup namespace only
permits a wider set of lookups to succeed now. The cgroup IDs across
namespaces are globally unique, and thus don't need to be retranslated.
Reported-by: Dan Schatzberg <dschatzberg@meta.com>
Signed-off-by: Kumar Kartikeya Dwivedi <memxor@gmail.com>
Acked-by: Tejun Heo <tj@kernel.org>
Link: https://lore.kernel.org/r/20250915032618.1551762-2-memxor@gmail.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f2537be4f8421f6495edfa0bc284d722f253841d ]
When forcefully shutting down a port via the configfs interface,
nvmet_port_subsys_drop_link() first calls nvmet_port_del_ctrls() and
then nvmet_disable_port(). Both functions will eventually schedule all
remaining associations for deletion.
The current implementation checks whether an association is about to be
removed, but only after the work item has already been scheduled. As a
result, it is possible for the first scheduled work item to free all
resources, and then for the same work item to be scheduled again for
deletion.
Because the association list is an RCU list, it is not possible to take
a lock and remove the list entry directly, so it cannot be looked up
again. Instead, a flag (terminating) must be used to determine whether
the association is already in the process of being deleted.
Reported-by: Shinichiro Kawasaki <shinichiro.kawasaki@wdc.com>
Closes: https://lore.kernel.org/all/rsdinhafrtlguauhesmrrzkybpnvwantwmyfq2ih5aregghax5@mhr7v3eryci3/
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Daniel Wagner <wagi@kernel.org>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6dbcd5a9ab6cb6644e7d728521da1c9035ec7235 ]
A TEE driver doesn't always need to provide a pool if it doesn't
support memory sharing ioctls and can allocate memory for TEE
messages in another way. Although this is mentioned in the
documentation for tee_device_alloc(), it is not handled correctly.
Reviewed-by: Sumit Garg <sumit.garg@oss.qualcomm.com>
Signed-off-by: Amirreza Zarrabi <amirreza.zarrabi@oss.qualcomm.com>
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e9dff11a7a50fcef23fe3e8314fafae6d5641826 ]
When deleting the previous walkstate operand stack
acpi_ds_call_control_method() was deleting obj_desc->Method.param_count
operands. But Method.param_count does not necessarily match
this_walk_state->num_operands, it may be either less or more.
After correcting the for loop to check `i < this_walk_state->num_operands`
the code is identical to acpi_ds_clear_operands(), so just outright
replace the code with acpi_ds_clear_operands() to fix this.
Link: https://github.com/acpica/acpica/commit/53fc0220
Signed-off-by: Hans de Goede <hansg@kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 08b68ca543ee9d5a8d2dc406165e4887dd8f170b ]
For Qualcomm SoCs which needs level shifter for SD card, extra delay is
seen on receiver data path.
To compensate this delay enable tuning for SDR50 mode for targets which
has level shifter. SDHCI_SDR50_NEEDS_TUNING caps will be set for targets
with level shifter on Qualcomm SOC's.
Signed-off-by: Sarthak Garg <quic_sartgarg@quicinc.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 767ecf9da7b31e5c0c22c273001cb2784705fe8c ]
On a few zcu106 boards USB devices (Dell MS116 USB Optical Mouse, Dell USB
Entry Keyboard) are not enumerated on linux boot due to commit
'b8745e7eb488 ("arm64: zynqmp: Fix usb node drive strength and slew
rate")'.
To fix it as a workaround revert to working version and then investigate
at board level why drive strength from 12mA to 4mA and slew from fast to
slow is not working.
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@amd.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/85a70cb014ec1f07972fccb60b875596eeaa6b5c.1756799774.git.michal.simek@amd.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c33c43f71bda362b292a6e57ac41b64342dc87b3 ]
On certain Loongson platforms, drivers attempting to request a legacy
ISA IRQ directly via request_irq() (e.g., IRQ 4) may fail. The
virtual IRQ descriptor is not fully initialized and lacks a valid irqchip.
This issue does not affect ACPI-enumerated devices described in DSDT,
as their interrupts are properly mapped via the GSI translation path.
This indicates the LPC irqdomain itself is functional but is not correctly
handling direct VIRQ-to-HWIRQ mappings.
The root cause is the use of irq_domain_create_linear(). This API sets
up a domain for dynamic, on-demand mapping, typically triggered by a GSI
request. It does not pre-populate the mappings for the legacy VIRQ range
(0-15). Consequently, if no ACPI device claims a specific GSI
(e.g., GSI 4), the corresponding VIRQ (e.g., VIRQ 4) is never mapped to
the LPC domain. A direct call to request_irq(4, ...) then fails because
the kernel cannot resolve this VIRQ to a hardware interrupt managed by
the LPC controller.
The PCH-LPC interrupt controller is an i8259-compatible legacy device
that requires a deterministic, static 1-to-1 mapping for IRQs 0-15 to
support legacy drivers.
Fix this by replacing irq_domain_create_linear() with
irq_domain_create_legacy(). This API is specifically designed for such
controllers. It establishes the required static 1-to-1 VIRQ-to-HWIRQ
mapping for the entire legacy range (0-15) immediately upon domain
creation. This ensures that any VIRQ in this range is always resolvable,
making direct calls to request_irq() for legacy IRQs function correctly.
Signed-off-by: Ming Wang <wangming01@loongson.cn>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit aae7a2876c3b39d07aa7655ea082af8e7862f3a5 ]
Unlike all the other allocations in this driver, the memory for storing
the pin function descriptions allocated with kcalloc() and later resized
with krealloc() is never freed. Use devres like elsewhere to handle
that. While at it - replace krealloc() with more suitable
devm_krealloc_array().
Note: the logic in this module is pretty convoluted and could probably
use some revisiting, we should probably be able to calculate the exact
amount of memory needed in advance or even skip the allocation
altogether and just add each function to the radix tree separately.
Tested-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d9d61f1da35038793156c04bb13f0a1350709121 ]
Many AMD CPUs can support this feature now. We would get a wrong CPU DIE
temperature if don't consider this. In low-temperature environments,
the CPU die temperature can drop below zero. So many platforms would like
to make extended temperature range as their default configuration.
Default temperature range (0C to 255.875C).
Extended temperature range (-49C to +206.875C).
Ref Doc: AMD V3000 PPR (Doc ID #56558).
Signed-off-by: Chuande Chen <chuachen@cisco.com>
Link: https://lore.kernel.org/r/20250814053940.96764-1-chenchuande@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e5d1e313d7b6272d6dfda983906d99f97ad9062b ]
The device ID of Strix Halo Data Fabric Function 3 has been in the tree
since commit 0e640f0a47d8 ("x86/amd_nb: Add new PCI IDs for AMD family
0x1a"), but is somehow missing from k10temp_id_table.
Add it so that it works out of the box.
Tested on Beelink GTR9 Pro Mini PC.
Signed-off-by: Rong Zhang <i@rong.moe>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://lore.kernel.org/r/20250823180443.85512-1-i@rong.moe
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fee0904441325d83e7578ca457ec65a9d3f21264 ]
The ASUS S15 xElite model report the Li-ion battery with an OOI, hence this
update the detection and return the appropriate type.
Signed-off-by: Christopher Ruehl <chris.ruehl@gtsys.com.hk>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4405a214df146775338a1e6232701a29024b82e1 ]
Some x86/ACPI laptops with MIPI cameras have a INTC10DE or INTC10E0 ACPI
device in the _DEP dependency list of the ACPI devices for the camera-
sensors (which have flags.honor_deps set).
These devices are for an Intel Vision CVS chip for which an out of tree
driver is available [1].
The camera sensor works fine without a driver being loaded for this
ACPI device on the 2 laptops this was tested on:
ThinkPad X1 Carbon Gen 12 (Meteor Lake)
ThinkPad X1 2-in-1 Gen 10 (Arrow Lake)
For now add these HIDs to acpi_ignore_dep_ids[] so that
acpi_dev_ready_for_enumeration() will return true once the other _DEP
dependencies are met and an i2c_client for the camera sensor will get
instantiated.
Link: https://github.com/intel/vision-drivers/ [1]
Signed-off-by: Hans de Goede <hansg@kernel.org>
Link: https://patch.msgid.link/20250829142748.21089-1-hansg@kernel.org
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2ef3886ce626dcdab0cbc452dbbebc19f57133d8 ]
The PCI Local Bus Specification 3.0 (section 6.8.1.6) allows modifying the
low-order bits of the MSI Message DATA register to encode nr_irqs interrupt
numbers in the log2(nr_irqs) bits for the domain.
The problem arises if the base vector (GICV2m base spi) is not aligned with
nr_irqs; in this case, the low-order log2(nr_irqs) bits from the base
vector conflict with the nr_irqs masking, causing the wrong MSI interrupt
to be identified.
To fix this, use bitmap_find_next_zero_area_off() instead of
bitmap_find_free_region() to align the initial base vector with nr_irqs.
Signed-off-by: Christian Bruel <christian.bruel@foss.st.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/all/20250902091045.220847-1-christian.bruel@foss.st.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a3fecb9160482367365cc384c59dd220b162b066 ]
While tracking down a problem where constant expressions used by
BUILD_BUG_ON() suddenly stopped working[1], we found that an added static
initializer was convincing the compiler that it couldn't track the state
of the prior statically initialized value. Tracing this down found that
ffs() was used in the initializer macro, but since it wasn't marked with
__attribute__const__, the compiler had to assume the function might
change variable states as a side-effect (which is not true for ffs(),
which provides deterministic math results).
For arc architecture with CONFIG_ISA_ARCV2=y, the __fls() function
uses __builtin_arc_fls() which lacks GCC's const attribute, preventing
compile-time constant folding, and KUnit testing of ffs/fls fails on
arc[3]. A patch[2] to GCC to solve this has been sent.
Add a fix for this by handling compile-time constants with the standard
__builtin_clzl() builtin (which has const attribute) while preserving
the optimized arc-specific builtin for runtime cases. This has the added
benefit of skipping runtime calculation of compile-time constant values.
Even with the GCC bug fixed (which is about "attribute const") this is a
good change to avoid needless runtime costs, and should be done
regardless of the state of GCC's bug.
Build tested ARCH=arc allyesconfig with GCC arc-linux 15.2.0.
Link: https://github.com/KSPP/linux/issues/364 [1]
Link: https://gcc.gnu.org/pipermail/gcc-patches/2025-August/693273.html
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202508031025.doWxtzzc-lkp@intel.com/ [3]
Signed-off-by: Kees Cook <kees@kernel.org>
Acked-by: Vineet Gupta <vgupta@kernel.org>
Signed-off-by: Yury Norov (NVIDIA) <yury.norov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 592532a77b736b5153e0c2e4c74aa50af0a352ab ]
longhaul_exit() was calling cpufreq_cpu_get(0) without checking
for a NULL policy pointer. On some systems, this could lead to a
NULL dereference and a kernel warning or panic.
This patch adds a check using unlikely() and returns early if the
policy is NULL.
Bugzilla: #219962
Signed-off-by: Dennis Beier <nanovim@gmail.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9c174e4dacee9fb2014a4ffc953d79a5707b77e4 ]
Wrong actual clock reported, if the SD clock division ratio is other
than 1:1(bits DIV[7:0] in SD_CLK_CTRL are set to 11111111).
On high speed mode, cat /sys/kernel/debug/mmc1/ios
Without the patch:
clock: 50000000 Hz
actual clock: 200000000 Hz
After the fix:
clock: 50000000 Hz
actual clock: 50000000 Hz
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20250629203859.170850-1-biju.das.jz@bp.renesas.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 236152dd9b1675a35eee912e79e6c57ca6b6732f ]
In the pin_config_set function, when handling PIN_CONFIG_BIAS_PULL_DOWN or
PIN_CONFIG_BIAS_PULL_UP, the function calls pcs_pinconf_clear_bias()
which writes the register. However, the subsequent operations continue
using the stale 'data' value from before the register write, effectively
causing the bias clear operation to be overwritten and not take effect.
Fix this by reading the 'data' value from the register after calling
pcs_pinconf_clear_bias().
This bug seems to have existed when this code was first merged in commit
9dddb4df90 ("pinctrl: single: support generic pinconf").
Signed-off-by: Chi Zhang <chizhang@asrmicro.com>
Link: https://lore.kernel.org/20250807062038.13610-1-chizhang@asrmicro.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2caa6b88e0ba0231fb4ff0ba8e73cedd5fb81fc8 ]
In the past %pK was preferable to %p as it would not leak raw pointer
values into the kernel log.
Since commit ad67b74d24 ("printk: hash addresses printed with %p")
the regular %p has been improved to avoid this issue.
Furthermore, restricted pointers ("%pK") were never meant to be used
through printk(). They can still unintentionally leak raw pointers or
acquire sleeping locks in atomic contexts.
Switch to the regular pointer formatting which is safer and
easier to reason about.
Signed-off-by: Thomas Weißschuh <thomas.weissschuh@linutronix.de>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20250811-restricted-pointers-bpf-v1-1-a1d7cc3cb9e7@linutronix.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b832b19318534bb4f1673b24d78037fee339c679 ]
In the past %pK was preferable to %p as it would not leak raw pointer
values into the kernel log.
Since commit ad67b74d24 ("printk: hash addresses printed with %p")
the regular %p has been improved to avoid this issue.
Furthermore, restricted pointers ("%pK") were never meant to be used
through printk(). They can still unintentionally leak raw pointers or
acquire sleeping locks in atomic contexts.
Switch to the regular pointer formatting which is safer and
easier to reason about.
There are still a few users of %pK left, but these use it through seq_file,
for which its usage is safe.
Signed-off-by: Thomas Weißschuh <thomas.weissschuh@linutronix.de>
Link: https://patch.msgid.link/20250811-restricted-pointers-spi-v1-1-32c47f954e4d@linutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit cfd6f1a7b42f62523c96d9703ef32b0dbc495ba4 upstream.
A race condition occurs when ffs_func_eps_enable() runs concurrently
with ffs_data_reset(). The ffs_data_clear() called in ffs_data_reset()
sets ffs->epfiles to NULL before resetting ffs->eps_count to 0, leading
to a NULL pointer dereference when accessing epfile->ep in
ffs_func_eps_enable() after successful usb_ep_enable().
The ffs->epfiles pointer is set to NULL in both ffs_data_clear() and
ffs_data_close() functions, and its modification is protected by the
spinlock ffs->eps_lock. And the whole ffs_func_eps_enable() function
is also protected by ffs->eps_lock.
Thus, add NULL pointer handling for ffs->epfiles in the
ffs_func_eps_enable() function to fix issues
Signed-off-by: Owen Gu <guhuinan@xiaomi.com>
Link: https://lore.kernel.org/r/20250915092907.17802-1-guhuinan@xiaomi.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0fd20f65df6aa430454a0deed8f43efa91c54835 ]
Do not block PCI config accesses through pci_cfg_access_lock() when
executing the s390 variant of PCI error recovery: Acquire just
device_lock() instead of pci_dev_lock() as powerpc's EEH and
generig PCI AER processing do.
During error recovery testing a pair of tasks was reported to be hung:
mlx5_core 0000:00:00.1: mlx5_health_try_recover:338:(pid 5553): health recovery flow aborted, PCI reads still not working
INFO: task kmcheck:72 blocked for more than 122 seconds.
Not tainted 5.14.0-570.12.1.bringup7.el9.s390x #1
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
task:kmcheck state:D stack:0 pid:72 tgid:72 ppid:2 flags:0x00000000
Call Trace:
[<000000065256f030>] __schedule+0x2a0/0x590
[<000000065256f356>] schedule+0x36/0xe0
[<000000065256f572>] schedule_preempt_disabled+0x22/0x30
[<0000000652570a94>] __mutex_lock.constprop.0+0x484/0x8a8
[<000003ff800673a4>] mlx5_unload_one+0x34/0x58 [mlx5_core]
[<000003ff8006745c>] mlx5_pci_err_detected+0x94/0x140 [mlx5_core]
[<0000000652556c5a>] zpci_event_attempt_error_recovery+0xf2/0x398
[<0000000651b9184a>] __zpci_event_error+0x23a/0x2c0
INFO: task kworker/u1664:6:1514 blocked for more than 122 seconds.
Not tainted 5.14.0-570.12.1.bringup7.el9.s390x #1
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
task:kworker/u1664:6 state:D stack:0 pid:1514 tgid:1514 ppid:2 flags:0x00000000
Workqueue: mlx5_health0000:00:00.0 mlx5_fw_fatal_reporter_err_work [mlx5_core]
Call Trace:
[<000000065256f030>] __schedule+0x2a0/0x590
[<000000065256f356>] schedule+0x36/0xe0
[<0000000652172e28>] pci_wait_cfg+0x80/0xe8
[<0000000652172f94>] pci_cfg_access_lock+0x74/0x88
[<000003ff800916b6>] mlx5_vsc_gw_lock+0x36/0x178 [mlx5_core]
[<000003ff80098824>] mlx5_crdump_collect+0x34/0x1c8 [mlx5_core]
[<000003ff80074b62>] mlx5_fw_fatal_reporter_dump+0x6a/0xe8 [mlx5_core]
[<0000000652512242>] devlink_health_do_dump.part.0+0x82/0x168
[<0000000652513212>] devlink_health_report+0x19a/0x230
[<000003ff80075a12>] mlx5_fw_fatal_reporter_err_work+0xba/0x1b0 [mlx5_core]
No kernel log of the exact same error with an upstream kernel is
available - but the very same deadlock situation can be constructed there,
too:
- task: kmcheck
mlx5_unload_one() tries to acquire devlink lock while the PCI error
recovery code has set pdev->block_cfg_access by way of
pci_cfg_access_lock()
- task: kworker
mlx5_crdump_collect() tries to set block_cfg_access through
pci_cfg_access_lock() while devlink_health_report() had acquired
the devlink lock.
A similar deadlock situation can be reproduced by requesting a
crdump with
> devlink health dump show pci/<BDF> reporter fw_fatal
while PCI error recovery is executed on the same <BDF> physical function
by mlx5_core's pci_error_handlers. On s390 this can be injected with
> zpcictl --reset-fw <BDF>
Tests with this patch failed to reproduce that second deadlock situation,
the devlink command is rejected with "kernel answers: Permission denied" -
and we get a kernel log message of:
mlx5_core 1ed0:00:00.1: mlx5_crdump_collect:50:(pid 254382): crdump: failed to lock vsc gw err -5
because the config read of VSC_SEMAPHORE is rejected by the underlying
hardware.
Two prior attempts to address this issue have been discussed and
ultimately rejected [see link], with the primary argument that s390's
implementation of PCI error recovery is imposing restrictions that
neither powerpc's EEH nor PCI AER handling need. Tests show that PCI
error recovery on s390 is running to completion even without blocking
access to PCI config space.
Link: https://lore.kernel.org/all/20251007144826.2825134-1-gbayer@linux.ibm.com/
Cc: stable@vger.kernel.org
Fixes: 4cdf2f4e24 ("s390/pci: implement minimal PCI error recovery")
Reviewed-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Gerd Bayer <gbayer@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
[ Adjust context ]
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 64e2f60f355e556337fcffe80b9bcff1b22c9c42 ]
As reported by Luiz Capitulino enabling HVO on s390 leads to reproducible
crashes. The problem is that kernel page tables are modified without
flushing corresponding TLB entries.
Even if it looks like the empty flush_tlb_all() implementation on s390 is
the problem, it is actually a different problem: on s390 it is not allowed
to replace an active/valid page table entry with another valid page table
entry without the detour over an invalid entry. A direct replacement may
lead to random crashes and/or data corruption.
In order to invalidate an entry special instructions have to be used
(e.g. ipte or idte). Alternatively there are also special instructions
available which allow to replace a valid entry with a different valid
entry (e.g. crdte or cspg).
Given that the HVO code currently does not provide the hooks to allow for
an implementation which is compliant with the s390 architecture
requirements, disable ARCH_WANT_OPTIMIZE_HUGETLB_VMEMMAP again, which is
basically a revert of the original patch which enabled it.
Reported-by: Luiz Capitulino <luizcap@redhat.com>
Closes: https://lore.kernel.org/all/20251028153930.37107-1-luizcap@redhat.com/
Fixes: 00a34d5a99 ("s390: select ARCH_WANT_HUGETLB_PAGE_OPTIMIZE_VMEMMAP")
Cc: stable@vger.kernel.org
Tested-by: Luiz Capitulino <luizcap@redhat.com>
Reviewed-by: Gerald Schaefer <gerald.schaefer@linux.ibm.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
[ Adjust context ]
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3af7524b14198f5159a86692d57a9f28ec9375ce upstream.
Running N CPU-bound tasks on an N CPUs platform:
- with asymmetric CPU capacity
- not being a DynamIq system (i.e. having a PKG level sched domain
without the SD_SHARE_PKG_RESOURCES flag set)
.. might result in a task placement where two tasks run on a big CPU
and none on a little CPU. This placement could be more optimal by
using all CPUs.
Testing platform:
Juno-r2:
- 2 big CPUs (1-2), maximum capacity of 1024
- 4 little CPUs (0,3-5), maximum capacity of 383
Testing workload ([1]):
Spawn 6 CPU-bound tasks. During the first 100ms (step 1), each tasks
is affine to a CPU, except for:
- one little CPU which is left idle.
- one big CPU which has 2 tasks affine.
After the 100ms (step 2), remove the cpumask affinity.
Behavior before the patch:
During step 2, the load balancer running from the idle CPU tags sched
domains as:
- little CPUs: 'group_has_spare'. Cf. group_has_capacity() and
group_is_overloaded(), 3 CPU-bound tasks run on a 4 CPUs
sched-domain, and the idle CPU provides enough spare capacity
regarding the imbalance_pct
- big CPUs: 'group_overloaded'. Indeed, 3 tasks run on a 2 CPUs
sched-domain, so the following path is used:
group_is_overloaded()
\-if (sgs->sum_nr_running <= sgs->group_weight) return true;
The following path which would change the migration type to
'migrate_task' is not taken:
calculate_imbalance()
\-if (env->idle != CPU_NOT_IDLE && env->imbalance == 0)
as the local group has some spare capacity, so the imbalance
is not 0.
The migration type requested is 'migrate_util' and the busiest
runqueue is the big CPU's runqueue having 2 tasks (each having a
utilization of 512). The idle little CPU cannot pull one of these
task as its capacity is too small for the task. The following path
is used:
detach_tasks()
\-case migrate_util:
\-if (util > env->imbalance) goto next;
After the patch:
As the number of failed balancing attempts grows (with
'nr_balance_failed'), progressively make it easier to migrate
a big task to the idling little CPU. A similar mechanism is
used for the 'migrate_load' migration type.
Improvement:
Running the testing workload [1] with the step 2 representing
a ~10s load for a big CPU:
Before patch: ~19.3s
After patch: ~18s (-6.7%)
Similar issue reported at:
https://lore.kernel.org/lkml/20230716014125.139577-1-qyousef@layalina.io/
Suggested-by: Vincent Guittot <vincent.guittot@linaro.org>
Signed-off-by: Pierre Gondois <pierre.gondois@arm.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Reviewed-by: Vincent Guittot <vincent.guittot@linaro.org>
Reviewed-by: Dietmar Eggemann <dietmar.eggemann@arm.com>
Acked-by: Qais Yousef <qyousef@layalina.io>
Link: https://lore.kernel.org/r/20231206090043.634697-1-pierre.gondois@arm.com
Cc: John Stultz <jstultz@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 50181c0cff31281b9f1071575ffba8a102375ece upstream.
Lukasz Luba reported that a thread's util_est can significantly decrease as
a result of sharing the CPU with other threads.
The use case can be easily reproduced with a periodic task TA that runs 1ms
and sleeps 100us. When the task is alone on the CPU, its max utilization and
its util_est is around 888. If another similar task starts to run on the
same CPU, TA will have to share the CPU runtime and its maximum utilization
will decrease around half the CPU capacity (512) then TA's util_est will
follow this new maximum trend which is only the result of sharing the CPU
with others tasks.
Such situation can be detected with runnable_avg wich is close or
equal to util_avg when TA is alone, but increases above util_avg when TA
shares the CPU with other threads and wait on the runqueue.
[ We prefer an util_est that overestimate rather than under estimate
because in 1st case we will not provide enough performance to the
task which will remain under-provisioned, whereas in the other case we
will create some idle time which will enable to reduce contention and
as a result reduces the util_est so the overestimate will be transient
whereas the underestimate will remain. ]
[ mingo: Refined the changelog, added comments from the LKML discussion. ]
Reported-by: Lukasz Luba <lukasz.luba@arm.com>
Signed-off-by: Vincent Guittot <vincent.guittot@linaro.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/lkml/CAKfTPtDd-HhF-YiNTtL9i5k0PfJbF819Yxu4YquzfXgwi7voyw@mail.gmail.com/#t
Link: https://lore.kernel.org/r/20231122140119.472110-1-vincent.guittot@linaro.org
Cc: Hongyan Xia <hongyan.xia2@arm.com>
Cc: John Stultz <jstultz@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit db86f55bf81a3a297be05ee8775ae9a8c6e3a599 ]
A throughput regression of 11% introduced by commit 779b1a1cb13a ("cpuidle:
governors: menu: Avoid selecting states with too much latency") has been
reported and it is related to the case when the menu governor checks if
selecting a proper idle state instead of a polling one makes sense.
In particular, it is questionable to do so if the exit latency of the
idle state in question exceeds the predicted idle duration, so add a
check for that, which is sufficient to make the reported regression go
away, and update the related code comment accordingly.
Fixes: 779b1a1cb13a ("cpuidle: governors: menu: Avoid selecting states with too much latency")
Closes: https://lore.kernel.org/linux-pm/004501dc43c9$ec8aa930$c59ffb90$@telus.net/
Reported-by: Doug Smythies <dsmythies@telus.net>
Tested-by: Doug Smythies <dsmythies@telus.net>
Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Christian Loehle <christian.loehle@arm.com>
Link: https://patch.msgid.link/12786727.O9o76ZdvQC@rafael.j.wysocki
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b45873c3f09153d1ad9b3a7bf9e5c0b0387fd2ea ]
Commit c1e18c17bd ("s390/pci: add zpci_set_irq()/zpci_clear_irq()"),
introduced the zpci_set_irq() and zpci_clear_irq(), to be used while
resetting a zPCI device.
Commit da995d538d ("s390/pci: implement reset_slot for hotplug
slot"), mentions zpci_clear_irq() being called in the path for
zpci_hot_reset_device(). But that is not the case anymore and these
functions are not called outside of this file. Instead
zpci_hot_reset_device() relies on zpci_disable_device() also clearing
the IRQs, but misses to reset the zdev->irqs_registered flag.
However after a CLP disable/enable reset, the device's IRQ are
unregistered, but the flag zdev->irq_registered does not get cleared. It
creates an inconsistent state and so arch_restore_msi_irqs() doesn't
correctly restore the device's IRQ. This becomes a problem when a PCI
driver tries to restore the state of the device through
pci_restore_state(). Restore IRQ unconditionally for the device and remove
the irq_registered flag as its redundant.
Fixes: c1e18c17bd ("s390/pci: add zpci_set_irq()/zpci_clear_irq()")
Cc: stable@vger.kernnel.org
Reviewed-by: Niklas Schnelle <schnelle@linux.ibm.com>
Reviewed-by: Matthew Rosato <mjrosato@linux.ibm.com>
Signed-off-by: Farhan Ali <alifm@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
[ adjusted bitfield context ]
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
