[ Upstream commit fc59462c5c ]
For an external clock source, which is gated via a GPIO, the
rate change should typically be propagated to the parent clock.
The situation where we are requiring this propagation, is when an
external clock is connected to override an internal clock (which typically
has a fixed rate). The external clock can have a different rate than the
internal one, and may also be variable, thus requiring the rate
propagation.
This rate change wasn't propagated until now, and it's unclear about cases
where this shouldn't be propagated. Thus, it's unclear whether this is
fixing a bug, or extending the current driver behavior. Also, it's unsure
about whether this may break any existing setups; in the case that it does,
a device-tree property may be added to disable this flag.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lkml.kernel.org/r/20191108071718.17985-1-alexandru.ardelean@analog.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit efd164b552 ]
Some RCGs (the gfx_3d_src_clk in msm8998 for example) are basically just
some constant ratio from the input across the entire frequency range. It
would be great if we could specify the frequency table as a single entry
constant ratio instead of a long list, ie:
{ .src = P_GPUPLL0_OUT_EVEN, .pre_div = 3 },
{ }
So, lets support that.
We need to fix a corner case in qcom_find_freq() where if the freq table
is non-null, but has no frequencies, we end up returning an "entry" before
the table array, which is bad. Then, we need ignore the freq from the
table, and instead base everything on the requested freq.
Suggested-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Link: https://lkml.kernel.org/r/20191031185715.15504-1-jeffrey.l.hugo@gmail.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2a60637f06 ]
As Eric reported:
RENAME_EXCHANGE support was just added to fsstress in xfstests:
commit 65dfd40a97b6bbbd2a22538977bab355c5bc0f06
Author: kaixuxia <xiakaixu1987@gmail.com>
Date: Thu Oct 31 14:41:48 2019 +0800
fsstress: add EXCHANGE renameat2 support
This is causing xfstest generic/579 to fail due to fsck.f2fs reporting errors.
I'm not sure what the problem is, but it still happens even with all the
fs-verity stuff in the test commented out, so that the test just runs fsstress.
generic/579 23s ... [10:02:25]
[ 7.745370] run fstests generic/579 at 2019-11-04 10:02:25
_check_generic_filesystem: filesystem on /dev/vdc is inconsistent
(see /results/f2fs/results-default/generic/579.full for details)
[10:02:47]
Ran: generic/579
Failures: generic/579
Failed 1 of 1 tests
Xunit report: /results/f2fs/results-default/result.xml
Here's the contents of 579.full:
_check_generic_filesystem: filesystem on /dev/vdc is inconsistent
*** fsck.f2fs output ***
[ASSERT] (__chk_dots_dentries:1378) --> Bad inode number[0x24] for '..', parent parent ino is [0xd10]
The root cause is that we forgot to update directory's i_pino during
cross_rename, fix it.
Fixes: 32f9bc25cb ("f2fs: support ->rename2()")
Signed-off-by: Chao Yu <yuchao0@huawei.com>
Tested-by: Eric Biggers <ebiggers@kernel.org>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7cfd5639d9 ]
If the driver receives a login that is later then LOGO'd by the remote port
(aka ndlp), the driver, upon the completion of the LOGO ACC transmission,
will logout the node and unregister the rpi that is being used for the
node. As part of the unreg, the node's rpi value is replaced by the
LPFC_RPI_ALLOC_ERROR value. If the port is subsequently offlined, the
offline walks the nodes and ensures they are logged out, which possibly
entails unreg'ing their rpi values. This path does not validate the node's
rpi value, thus doesn't detect that it has been unreg'd already. The
replaced rpi value is then used when accessing the rpi bitmask array which
tracks active rpi values. As the LPFC_RPI_ALLOC_ERROR value is not a valid
index for the bitmask, it may fault the system.
Revise the rpi release code to detect when the rpi value is the replaced
RPI_ALLOC_ERROR value and ignore further release steps.
Link: https://lore.kernel.org/r/20191105005708.7399-2-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2e9b51d782 ]
This patch addresses what Dave Chinner had discovered and fixed within
commit: 7684e2c438. This changes does not have any user visible
impact for ext4 as none of the current users of ext4_iomap_begin()
that extend files depend on IOMAP_F_DIRTY.
When doing a direct IO that spans the current EOF, and there are
written blocks beyond EOF that extend beyond the current write, the
only metadata update that needs to be done is a file size extension.
However, we don't mark such iomaps as IOMAP_F_DIRTY to indicate that
there is IO completion metadata updates required, and hence we may
fail to correctly sync file size extensions made in IO completion when
O_DSYNC writes are being used and the hardware supports FUA.
Hence when setting IOMAP_F_DIRTY, we need to also take into account
whether the iomap spans the current EOF. If it does, then we need to
mark it dirty so that IO completion will call generic_write_sync() to
flush the inode size update to stable storage correctly.
Signed-off-by: Matthew Bobrowski <mbobrowski@mbobrowski.org>
Reviewed-by: Jan Kara <jack@suse.cz>
Reviewed-by: Ritesh Harjani <riteshh@linux.ibm.com>
Link: https://lore.kernel.org/r/8b43ee9ee94bee5328da56ba0909b7d2229ef150.1572949325.git.mbobrowski@mbobrowski.org
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 16f6b67cf0 ]
With large memory (8TB and more) hotplug, we can get soft lockup
warnings as below. These were caused by a long loop without any
explicit cond_resched which is a problem for !PREEMPT kernels.
Avoid this using cond_resched() while inserting hash page table
entries. We already do similar cond_resched() in __add_pages(), see
commit f64ac5e6e3 ("mm, memory_hotplug: add scheduling point to
__add_pages").
rcu: 3-....: (24002 ticks this GP) idle=13e/1/0x4000000000000002 softirq=722/722 fqs=12001
(t=24003 jiffies g=4285 q=2002)
NMI backtrace for cpu 3
CPU: 3 PID: 3870 Comm: ndctl Not tainted 5.3.0-197.18-default+ #2
Call Trace:
dump_stack+0xb0/0xf4 (unreliable)
nmi_cpu_backtrace+0x124/0x130
nmi_trigger_cpumask_backtrace+0x1ac/0x1f0
arch_trigger_cpumask_backtrace+0x28/0x3c
rcu_dump_cpu_stacks+0xf8/0x154
rcu_sched_clock_irq+0x878/0xb40
update_process_times+0x48/0x90
tick_sched_handle.isra.16+0x4c/0x80
tick_sched_timer+0x68/0xe0
__hrtimer_run_queues+0x180/0x430
hrtimer_interrupt+0x110/0x300
timer_interrupt+0x108/0x2f0
decrementer_common+0x114/0x120
--- interrupt: 901 at arch_add_memory+0xc0/0x130
LR = arch_add_memory+0x74/0x130
memremap_pages+0x494/0x650
devm_memremap_pages+0x3c/0xa0
pmem_attach_disk+0x188/0x750
nvdimm_bus_probe+0xac/0x2c0
really_probe+0x148/0x570
driver_probe_device+0x19c/0x1d0
device_driver_attach+0xcc/0x100
bind_store+0x134/0x1c0
drv_attr_store+0x44/0x60
sysfs_kf_write+0x64/0x90
kernfs_fop_write+0x1a0/0x270
__vfs_write+0x3c/0x70
vfs_write+0xd0/0x260
ksys_write+0xdc/0x130
system_call+0x5c/0x68
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20191001084656.31277-1-aneesh.kumar@linux.ibm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8e6b6da91a ]
Some PowerPC CPUs are vulnerable to L1TF to the same extent as to
Meltdown. It is also mitigated by flushing the L1D on privilege
transition.
Currently the sysfs gives a false negative on L1TF on CPUs that I
verified to be vulnerable, a Power9 Talos II Boston 004e 1202, PowerNV
T2P9D01.
Signed-off-by: Anthony Steinhauser <asteinhauser@google.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
[mpe: Just have cpu_show_l1tf() call cpu_show_meltdown() directly]
Link: https://lore.kernel.org/r/20191029190759.84821-1-asteinhauser@google.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4411464d6f ]
If a hardware-specific driver does not provide a name, the timer-of core
falls back to device_node.name. Due to generic DT node naming policies,
that name is almost always "timer", and thus doesn't identify the actual
timer used.
Fix this by using device_node.full_name instead, which includes the unit
addrees.
Example impact on /proc/timer_list:
-Clock Event Device: timer
+Clock Event Device: timer@fcfec400
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20191016144747.29538-3-geert+renesas@glider.be
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 396128d2ff ]
Instead use devm_regulator_get_optional since the regulator
is optional and check for errors.
Signed-off-by: Guido Günther <agx@sigxcpu.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9ff6aa027d ]
debug_dma_dump_mappings() can take a lot of cpu cycles :
lpk43:/# time wc -l /sys/kernel/debug/dma-api/dump
163435 /sys/kernel/debug/dma-api/dump
real 0m0.463s
user 0m0.003s
sys 0m0.459s
Let's add a cond_resched() to avoid holding cpu for too long.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Corentin Labbe <clabbe@baylibre.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e44ff9ea8f ]
Some of our scripts are passed $objdump and then call it as
"$objdump". This doesn't work if it contains spaces because we're
using ccache, for example you get errors such as:
./arch/powerpc/tools/relocs_check.sh: line 48: ccache ppc64le-objdump: No such file or directory
./arch/powerpc/tools/unrel_branch_check.sh: line 26: ccache ppc64le-objdump: No such file or directory
Fix it by not quoting the string when we expand it, allowing the shell
to do the right thing for us.
Fixes: a71aa05e14 ("powerpc: Convert relocs_check to a shell script using grep")
Fixes: 4ea80652dc ("powerpc/64s: Tool to flag direct branches from unrelocated interrupt vectors")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20191024004730.32135-1-mpe@ellerman.id.au
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 75838a3290 ]
If the hypervisor returned H_PTEG_FULL for H_ENTER hcall, retry a hash page table
insert by removing a random entry from the group.
After some runtime, it is very well possible to find all the 8 hash page table
entry slot in the hpte group used for mapping. Don't fail a bolted entry insert
in that case. With Storage class memory a user can find this error easily since
a namespace enable/disable is equivalent to memory add/remove.
This results in failures as reported below:
$ ndctl create-namespace -r region1 -t pmem -m devdax -a 65536 -s 100M
libndctl: ndctl_dax_enable: dax1.3: failed to enable
Error: namespace1.2: failed to enable
failed to create namespace: No such device or address
In kernel log we find the details as below:
Unable to create mapping for hot added memory 0xc000042006000000..0xc00004200d000000: -1
dax_pmem: probe of dax1.3 failed with error -14
This indicates that we failed to create a bolted hash table entry for direct-map
address backing the namespace.
We also observe failures such that not all namespaces will be enabled with
ndctl enable-namespace all command.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20191024093542.29777-2-aneesh.kumar@linux.ibm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit eb8e20f890 ]
accumulate_stolen_time() is called prior to interrupt state being
reconciled, which can trip the warning in arch_local_irq_restore():
WARNING: CPU: 5 PID: 1017 at arch/powerpc/kernel/irq.c:258 .arch_local_irq_restore+0x9c/0x130
...
NIP .arch_local_irq_restore+0x9c/0x130
LR .rb_start_commit+0x38/0x80
Call Trace:
.ring_buffer_lock_reserve+0xe4/0x620
.trace_function+0x44/0x210
.function_trace_call+0x148/0x170
.ftrace_ops_no_ops+0x180/0x1d0
ftrace_call+0x4/0x8
.accumulate_stolen_time+0x1c/0xb0
decrementer_common+0x124/0x160
For now just mark it as notrace. We may change the ordering to call it
after interrupt state has been reconciled, but that is a larger
change.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20191024055932.27940-1-mpe@ellerman.id.au
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 550c0d89d5 ]
For IOs from upper layer, preemption may be disabled as it may be called by
function __blk_mq_delay_run_hw_queue which will call get_cpu() (it disables
preemption). So if flags HISI_SAS_REJECT_CMD_BIT is set in function
hisi_sas_task_exec(), it may disable preempt twice after down() and up()
which will cause following call trace:
BUG: scheduling while atomic: fio/60373/0x00000002
Call trace:
dump_backtrace+0x0/0x150
show_stack+0x24/0x30
dump_stack+0xa0/0xc4
__schedule_bug+0x68/0x88
__schedule+0x4b8/0x548
schedule+0x40/0xd0
schedule_timeout+0x200/0x378
__down+0x78/0xc8
down+0x54/0x70
hisi_sas_task_exec.isra.10+0x598/0x8d8 [hisi_sas_main]
hisi_sas_queue_command+0x28/0x38 [hisi_sas_main]
sas_queuecommand+0x168/0x1b0 [libsas]
scsi_queue_rq+0x2ac/0x980
blk_mq_dispatch_rq_list+0xb0/0x550
blk_mq_do_dispatch_sched+0x6c/0x110
blk_mq_sched_dispatch_requests+0x114/0x1d8
__blk_mq_run_hw_queue+0xb8/0x130
__blk_mq_delay_run_hw_queue+0x1c0/0x220
blk_mq_run_hw_queue+0xb0/0x128
blk_mq_sched_insert_requests+0xdc/0x208
blk_mq_flush_plug_list+0x1b4/0x3a0
blk_flush_plug_list+0xdc/0x110
blk_finish_plug+0x3c/0x50
blkdev_direct_IO+0x404/0x550
generic_file_read_iter+0x9c/0x848
blkdev_read_iter+0x50/0x78
aio_read+0xc8/0x170
io_submit_one+0x1fc/0x8d8
__arm64_sys_io_submit+0xdc/0x280
el0_svc_common.constprop.0+0xe0/0x1e0
el0_svc_handler+0x34/0x90
el0_svc+0x10/0x14
...
To solve the issue, check preemptible() to avoid disabling preempt multiple
when flag HISI_SAS_REJECT_CMD_BIT is set.
Link: https://lore.kernel.org/r/1571926105-74636-5-git-send-email-john.garry@huawei.com
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit feff8b3d84 ]
When operating in private loop mode, PLOGI exchanges are racing and the
driver tries to abort it's PLOGI. But the PLOGI abort ends up terminating
the login with the other end causing the other end to abort its PLOGI as
well. Discovery never fully completes.
Fix by disabling the PLOGI abort when private loop and letting the state
machine play out.
Link: https://lore.kernel.org/r/20191018211832.7917-5-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9cef2a7955 ]
RFC 2307 states:
For CHAP [RFC1994], in the first step, the initiator MUST send:
CHAP_A=<A1,A2...>
Where A1,A2... are proposed algorithms, in order of preference.
...
For the Algorithm, as stated in [RFC1994], one value is required to
be implemented:
5 (CHAP with MD5)
LIO currently checks for this value by only comparing a single byte in
the tokenized Algorithm string, which means that any value starting with
a '5' (e.g. "55") is interpreted as "CHAP with MD5". Fix this by
comparing the entire tokenized string.
Reviewed-by: Lee Duncan <lduncan@suse.com>
Reviewed-by: Mike Christie <mchristi@redhat.com>
Signed-off-by: David Disseldorp <ddiss@suse.de>
Link: https://lore.kernel.org/r/20190912095547.22427-2-ddiss@suse.de
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8a631a5a0f ]
Whenever we reset the channel, we need to clear desc_pendingcount
along with desc_submitcount. Otherwise when a new transaction is
submitted, the irq coalesce level could be programmed to an incorrect
value in the axidma case.
This behavior can be observed when terminating pending transactions
with xilinx_dma_terminate_all() and then submitting new transactions
without releasing and requesting the channel.
Signed-off-by: Nicholas Graumann <nick.graumann@gmail.com>
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Link: https://lore.kernel.org/r/1571150904-3988-8-git-send-email-radhey.shyam.pandey@xilinx.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 96d3ab802e ]
Page tables that reside in physical memory beyond the 4 GiB boundary are
currently not working properly. The reason is that when the physical
address for page directory entries is read, it gets truncated at 32 bits
and can cause crashes when passing that address to the DMA API.
Fix this by first casting the PDE value to a dma_addr_t and then using
the page frame number mask for the SMMU instance to mask out the invalid
bits, which are typically used for mapping attributes, etc.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 42bb97b80f ]
IOMMU domain resource life is well-defined, managed
by .domain_alloc and .domain_free.
Therefore, domain-specific resources shouldn't be tied to
the device life, but instead to its domain.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fe1897eaa6 ]
generic/018 reports an inconsistent status of atime, the
testcase is as below:
- open file with O_SYNC
- write file to construct fraged space
- calc md5 of file
- record {a,c,m}time
- defrag file --- do nothing
- umount & mount
- check {a,c,m}time
The root cause is, as f2fs enables lazytime by default, atime
update will dirty vfs inode, rather than dirtying f2fs inode (by set
with FI_DIRTY_INODE), so later f2fs_write_inode() called from VFS will
fail to update inode page due to our skip:
f2fs_write_inode()
if (is_inode_flag_set(inode, FI_DIRTY_INODE))
return 0;
So eventually, after evict(), we lose last atime for ever.
To fix this issue, we need to check whether {a,c,m,cr}time is
consistent in between inode cache and inode page, and only skip
f2fs_update_inode() if f2fs inode is not dirty and time is
consistent as well.
Signed-off-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 463fa44eec ]
Across suspend and resume, we are seeing error messages like the following:
atmel_mxt_ts i2c-PRP0001:00: __mxt_read_reg: i2c transfer failed (-121)
atmel_mxt_ts i2c-PRP0001:00: Failed to read T44 and T5 (-121)
This occurs because the driver leaves its IRQ enabled. Upon resume, there
is an IRQ pending, but the interrupt is serviced before both the driver and
the underlying I2C bus have been resumed. This causes EREMOTEIO errors.
Disable the IRQ in suspend, and re-enable it on resume. If there are cases
where the driver enters suspend with interrupts disabled, that's a bug we
should fix separately.
Signed-off-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 07b8582430 ]
Symptoms were seen of the driver not having valid data for mailbox
commands. After debugging, the following sequence was found:
The driver maintains a port-wide pointer of the mailbox command that is
currently in execution. Once finished, the port-wide pointer is cleared
(done in lpfc_sli4_mq_release()). The next mailbox command issued will set
the next pointer and so on.
The mailbox response data is only copied if there is a valid port-wide
pointer.
In the failing case, it was seen that a new mailbox command was being
attempted in parallel with the completion. The parallel path was seeing
the mailbox no long in use (flag check under lock) and thus set the port
pointer. The completion path had cleared the active flag under lock, but
had not touched the port pointer. The port pointer is cleared after the
lock is released. In this case, the completion path cleared the just-set
value by the parallel path.
Fix by making the calls that clear mbox state/port pointer while under
lock. Also slightly cleaned up the error path.
Link: https://lore.kernel.org/r/20190922035906.10977-8-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 782b281883 ]
When user issues diag register command from application with required size,
and if driver unable to allocate the memory, then it will fail the register
command. While failing the register command, driver is not currently
clearing MPT3_CMD_PENDING bit in ctl_cmds.status variable which was set
before trying to allocate the memory. As this bit is set, subsequent
register command will be failed with BUSY status even when user wants to
register the trace buffer will less memory.
Clear MPT3_CMD_PENDING bit in ctl_cmds.status before returning the diag
register command with no memory status.
Link: https://lore.kernel.org/r/1568379890-18347-4-git-send-email-sreekanth.reddy@broadcom.com
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3f97aed611 ]
An issue was seen discovering all SCSI Luns when a target device undergoes
link bounce.
The driver currently does not qualify the FC4 support on the target.
Therefore it will send a SCSI PRLI and an NVMe PRLI. The expectation is
that the target will reject the PRLI if it is not supported. If a PRLI
times out, the driver will retry. The driver will not proceed with the
device until both SCSI and NVMe PRLIs are resolved. In the failure case,
the device is FCP only and does not respond to the NVMe PRLI, thus
initiating the wait/retry loop in the driver. During that time, a RSCN is
received (device bounced) causing the driver to issue a GID_FT. The GID_FT
response comes back before the PRLI mess is resolved and it prematurely
cancels the PRLI retry logic and leaves the device in a STE_PRLI_ISSUE
state. Discovery with the target never completes or resets.
Fix by resetting the node state back to STE_NPR_NODE when GID_FT completes,
thereby restarting the discovery process for the node.
Link: https://lore.kernel.org/r/20190922035906.10977-10-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 91e2f539ee upstream.
Fix die_walk_lines() to list the function entry line correctly. Since
the dwarf_entrypc() does not return the entry pc if the DIE has only
range attribute, __die_walk_funclines() fails to list the declaration
line (entry line) in that case.
To solve this issue, this introduces die_entrypc() which correctly
returns the entry PC (the first address range) even if the DIE has only
range attribute. With this fix die_walk_lines() shows the function entry
line is able to probe correctly.
Fixes: 4cc9cec636 ("perf probe: Introduce lines walker interface")
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Link: http://lore.kernel.org/lkml/157190837419.1859.4619125803596816752.stgit@devnote2
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Thomas Backlund <tmb@mageia.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1c05839aa9 upstream.
This fixes a regression added with:
commit e9e006f5fc
Author: Mike Christie <mchristi@redhat.com>
Date: Sun Aug 4 14:10:06 2019 -0500
nbd: fix max number of supported devs
where we can deadlock during device shutdown. The problem occurs if
the recv_work's nbd_config_put occurs after nbd_start_device_ioctl has
returned and the userspace app has droppped its reference via closing
the device and running nbd_release. The recv_work nbd_config_put call
would then drop the refcount to zero and try to destroy the config which
would try to do destroy_workqueue from the recv work.
This patch just has nbd_start_device_ioctl do a flush_workqueue when it
wakes so we know after the ioctl returns running works have exited. This
also fixes a possible race where we could try to reuse the device while
old recv_works are still running.
Cc: stable@vger.kernel.org
Fixes: e9e006f5fc ("nbd: fix max number of supported devs")
Signed-off-by: Mike Christie <mchristi@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fe0acab448 upstream.
Two previous patches introduced below quirks for P2020 platforms.
- SDHCI_QUIRK_RESET_AFTER_REQUEST
- SDHCI_QUIRK_BROKEN_TIMEOUT_VAL
The patches made a mistake to add them in quirks2 of sdhci_host
structure, while they were defined for quirks.
host->quirks2 |= SDHCI_QUIRK_RESET_AFTER_REQUEST;
host->quirks2 |= SDHCI_QUIRK_BROKEN_TIMEOUT_VAL;
This patch is to fix them.
host->quirks |= SDHCI_QUIRK_RESET_AFTER_REQUEST;
host->quirks |= SDHCI_QUIRK_BROKEN_TIMEOUT_VAL;
Fixes: 05cb6b2a66 ("mmc: sdhci-of-esdhc: add erratum eSDHC-A001 and A-008358 support")
Fixes: a46e427125 ("mmc: sdhci-of-esdhc: add erratum eSDHC5 support")
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20191216031842.40068-1-yangbo.lu@nxp.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2c92dd2030 upstream.
Tuning support in DDR50 speed mode was added in SD Specifications Part1
Physical Layer Specification v3.01. Its not possible to distinguish
between v3.00 and v3.01 from the SCR and that is why since
commit 4324f6de6d ("mmc: core: enable CMD19 tuning for DDR50 mode")
tuning failures are ignored in DDR50 speed mode.
Cards compatible with v3.00 don't respond to CMD19 in DDR50 and this
error gets printed during enumeration and also if retune is triggered at
any time during operation. Update the printk level to pr_debug so that
these errors don't lead to false error reports.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Cc: stable@vger.kernel.org # v4.4+
Link: https://lore.kernel.org/r/20191206114326.15856-1-faiz_abbas@ti.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8b6dc6b2d6 upstream.
This reverts commit 5dd1955225.
First, the fix seems to be plain wrong, since the erratum suggests
waiting 5ms before setting setting SYSCTL[RSTD], but this msleep()
happens after the call of sdhci_reset() which is where that bit gets
set (if SDHCI_RESET_DATA is in mask).
Second, walking the whole device tree to figure out if some node has a
"fsl,p2020-esdhc" compatible string is hugely expensive - about 70 to
100 us on our mpc8309 board. Walking the device tree is done under a
raw_spin_lock, so this is obviously really bad on an -rt system, and a
waste of time on all.
In fact, since esdhc_reset() seems to get called around 100 times per
second, that mpc8309 now spends 0.8% of its time determining that
it is not a p2020. Whether those 100 calls/s are normal or due to some
other bug or misconfiguration, regularly hitting a 100 us
non-preemptible window is unacceptable.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20191204085447.27491-1-linux@rasmusvillemoes.dk
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 966af20929 upstream.
Each logical CPU in Scalable MCA systems controls a unique set of MCA
banks in the system. These banks are not shared between CPUs. The bank
types and ordering will be the same across CPUs on currently available
systems.
However, some CPUs may see a bank as Reserved/Read-as-Zero (RAZ) while
other CPUs do not. In this case, the bank seen as Reserved on one CPU is
assumed to be the same type as the bank seen as a known type on another
CPU.
In general, this occurs when the hardware represented by the MCA bank
is disabled, e.g. disabled memory controllers on certain models, etc.
The MCA bank is disabled in the hardware, so there is no possibility of
getting an MCA/MCE from it even if it is assumed to have a known type.
For example:
Full system:
Bank | Type seen on CPU0 | Type seen on CPU1
------------------------------------------------
0 | LS | LS
1 | UMC | UMC
2 | CS | CS
System with hardware disabled:
Bank | Type seen on CPU0 | Type seen on CPU1
------------------------------------------------
0 | LS | LS
1 | UMC | RAZ
2 | CS | CS
For this reason, there is a single, global struct smca_banks[] that is
initialized at boot time. This array is initialized on each CPU as it
comes online. However, the array will not be updated if an entry already
exists.
This works as expected when the first CPU (usually CPU0) has all
possible MCA banks enabled. But if the first CPU has a subset, then it
will save a "Reserved" type in smca_banks[]. Successive CPUs will then
not be able to update smca_banks[] even if they encounter a known bank
type.
This may result in unexpected behavior. Depending on the system
configuration, a user may observe issues enumerating the MCA
thresholding sysfs interface. The issues may be as trivial as sysfs
entries not being available, or as severe as system hangs.
For example:
Bank | Type seen on CPU0 | Type seen on CPU1
------------------------------------------------
0 | LS | LS
1 | RAZ | UMC
2 | CS | CS
Extend the smca_banks[] entry check to return if the entry is a
non-reserved type. Otherwise, continue so that CPUs that encounter a
known bank type can update smca_banks[].
Fixes: 68627a697c ("x86/mce/AMD, EDAC/mce_amd: Enumerate Reserved SMCA bank type")
Signed-off-by: Yazen Ghannam <yazen.ghannam@amd.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: linux-edac <linux-edac@vger.kernel.org>
Cc: <stable@vger.kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: x86-ml <x86@kernel.org>
Link: https://lkml.kernel.org/r/20191121141508.141273-1-Yazen.Ghannam@amd.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 246ff09f89 upstream.
... because interrupts are disabled that early and sending IPIs can
deadlock:
BUG: sleeping function called from invalid context at kernel/sched/completion.c:99
in_atomic(): 1, irqs_disabled(): 1, non_block: 0, pid: 0, name: swapper/1
no locks held by swapper/1/0.
irq event stamp: 0
hardirqs last enabled at (0): [<0000000000000000>] 0x0
hardirqs last disabled at (0): [<ffffffff8106dda9>] copy_process+0x8b9/0x1ca0
softirqs last enabled at (0): [<ffffffff8106dda9>] copy_process+0x8b9/0x1ca0
softirqs last disabled at (0): [<0000000000000000>] 0x0
Preemption disabled at:
[<ffffffff8104703b>] start_secondary+0x3b/0x190
CPU: 1 PID: 0 Comm: swapper/1 Not tainted 5.5.0-rc2+ #1
Hardware name: GIGABYTE MZ01-CE1-00/MZ01-CE1-00, BIOS F02 08/29/2018
Call Trace:
dump_stack
___might_sleep.cold.92
wait_for_completion
? generic_exec_single
rdmsr_safe_on_cpu
? wrmsr_on_cpus
mce_amd_feature_init
mcheck_cpu_init
identify_cpu
identify_secondary_cpu
smp_store_cpu_info
start_secondary
secondary_startup_64
The function smca_configure() is called only on the current CPU anyway,
therefore replace rdmsr_safe_on_cpu() with atomic rdmsr_safe() and avoid
the IPI.
[ bp: Update commit message. ]
Signed-off-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Yazen Ghannam <yazen.ghannam@amd.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: linux-edac <linux-edac@vger.kernel.org>
Cc: <stable@vger.kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: x86-ml <x86@kernel.org>
Link: https://lkml.kernel.org/r/157252708836.3876.4604398213417262402.stgit@buzz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1ce74e96c2 upstream.
Commit 4b927b94d5 ("KVM: arm/arm64: vgic: Introduce find_reg_by_id()")
introduced 'find_reg_by_id()', which looks up a system register only if
the 'id' index parameter identifies a valid system register. As part of
the patch, existing callers of 'find_reg()' were ported over to the new
interface, but this breaks 'index_to_sys_reg_desc()' in the case that the
initial lookup in the vCPU target table fails because we will then call
into 'find_reg()' for the system register table with an uninitialised
'param' as the key to the lookup.
GCC 10 is bright enough to spot this (amongst a tonne of false positives,
but hey!):
| arch/arm64/kvm/sys_regs.c: In function ‘index_to_sys_reg_desc.part.0.isra’:
| arch/arm64/kvm/sys_regs.c:983:33: warning: ‘params.Op2’ may be used uninitialized in this function [-Wmaybe-uninitialized]
| 983 | (u32)(x)->CRn, (u32)(x)->CRm, (u32)(x)->Op2);
| [...]
Revert the hunk of 4b927b94d5 which breaks 'index_to_sys_reg_desc()' so
that the old behaviour of checking the index upfront is restored.
Fixes: 4b927b94d5 ("KVM: arm/arm64: vgic: Introduce find_reg_by_id()")
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20191212094049.12437-1-will@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 109ba779d6 upstream.
ext4_check_dir_entry() currently does not catch a case when a directory
entry ends so close to the block end that the header of the next
directory entry would not fit in the remaining space. This can lead to
directory iteration code trying to access address beyond end of current
buffer head leading to oops.
CC: stable@vger.kernel.org
Signed-off-by: Jan Kara <jack@suse.cz>
Link: https://lore.kernel.org/r/20191202170213.4761-3-jack@suse.cz
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 64d4ce8923 upstream.
Function ext4_empty_dir() doesn't correctly handle directories with
holes and crashes on bh->b_data dereference when bh is NULL. Reorganize
the loop to use 'offset' variable all the times instead of comparing
pointers to current direntry with bh->b_data pointer. Also add more
strict checking of '.' and '..' directory entries to avoid entering loop
in possibly invalid state on corrupted filesystems.
References: CVE-2019-19037
CC: stable@vger.kernel.org
Fixes: 4e19d6b65f ("ext4: allow directory holes")
Signed-off-by: Jan Kara <jack@suse.cz>
Link: https://lore.kernel.org/r/20191202170213.4761-2-jack@suse.cz
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ab42b48f32 upstream.
The "auto-attach" handler function `gsc_hpdi_auto_attach()` calls
`dma_alloc_coherent()` in a loop to allocate some DMA data buffers, and
also calls it to allocate a buffer for a DMA descriptor chain. However,
it does not check the return value of any of these calls. Change
`gsc_hpdi_auto_attach()` to return `-ENOMEM` if any of these
`dma_alloc_coherent()` calls fail. This will result in the comedi core
calling the "detach" handler `gsc_hpdi_detach()` as part of the
clean-up, which will call `gsc_hpdi_free_dma()` to free any allocated
DMA coherent memory buffers.
Cc: <stable@vger.kernel.org> #4.6+
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Link: https://lore.kernel.org/r/20191216110823.216237-1-abbotti@mev.co.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 133b2acee3 upstream.
At least on the HP Envy x360 15-cp0xxx model the WMI interface
for HPWMI_FEATURE2_QUERY requires an outsize of at least 128 bytes,
otherwise it fails with an error code 5 (HPWMI_RET_INVALID_PARAMETERS):
Dec 06 00:59:38 kernel: hp_wmi: query 0xd returned error 0x5
We do not care about the contents of the buffer, we just want to know
if the HPWMI_FEATURE2_QUERY command is supported.
This commits bumps the buffer size, fixing the error.
Fixes: 8a1513b493 ("hp-wmi: limit hotkey enable")
Cc: stable@vger.kernel.org
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1520703
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
