commit 4bd5ead82d upstream.
Since the role_store() uses strncmp(), it's possible to refer
out-of-memory if the sysfs data size is smaller than strlen("host").
This patch fixes it by using sysfs_streq() instead of strncmp().
Reported-by: Pavel Machek <pavel@denx.de>
Fixes: 9bb86777fb ("phy: rcar-gen3-usb2: add sysfs for usb role swap")
Cc: <stable@vger.kernel.org> # v4.10+
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Pavel Machek <pavel@denx.de>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d3abda5a98 upstream.
Normally the END_TRANSFER command completion handler will clear the
DWC3_EP_TRANSFER_STARTED flag. However, if the command was sent without
interrupt on completion, then the flag will not be cleared. Make sure to
clear the flag in this case.
Cc: stable@vger.kernel.org
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8c7d4b7b3d upstream.
This patch corrects the condition to kick the transfer without
giving back the requests when either request has remaining data
or when there are pending SGs. The && check was introduced during
spliting up the dwc3_gadget_ep_cleanup_completed_requests() function.
Fixes: f38e35dd84 ("usb: dwc3: gadget: split dwc3_gadget_ep_cleanup_completed_requests()")
Cc: stable@vger.kernel.org
Signed-off-by: Tejas Joglekar <joglekar@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bc71d8b580 upstream.
When virt_wifi interface is created, virt_wifi_newlink() is called and
it calls register_netdevice().
if register_netdevice() fails, it internally would call
->priv_destructor(), which is virt_wifi_net_device_destructor() and
it frees netdev. but virt_wifi_newlink() still use netdev.
So, use-after-free would occur in virt_wifi_newlink().
Test commands:
ip link add dummy0 type dummy
modprobe bonding
ip link add bonding_masters link dummy0 type virt_wifi
Splat looks like:
[ 202.220554] BUG: KASAN: use-after-free in virt_wifi_newlink+0x88b/0x9a0 [virt_wifi]
[ 202.221659] Read of size 8 at addr ffff888061629cb8 by task ip/852
[ 202.222896] CPU: 1 PID: 852 Comm: ip Not tainted 5.4.0-rc5 #3
[ 202.223765] Hardware name: innotek GmbH VirtualBox/VirtualBox, BIOS VirtualBox 12/01/2006
[ 202.225073] Call Trace:
[ 202.225532] dump_stack+0x7c/0xbb
[ 202.226869] print_address_description.constprop.5+0x1be/0x360
[ 202.229362] __kasan_report+0x12a/0x16f
[ 202.230714] kasan_report+0xe/0x20
[ 202.232595] virt_wifi_newlink+0x88b/0x9a0 [virt_wifi]
[ 202.233370] __rtnl_newlink+0xb9f/0x11b0
[ 202.244909] rtnl_newlink+0x65/0x90
[ ... ]
Cc: stable@vger.kernel.org
Fixes: c7cdba31ed ("mac80211-next: rtnetlink wifi simulation device")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Link: https://lore.kernel.org/r/20191121122645.9355-1-ap420073@gmail.com
[trim stack dump a bit]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a3c4c2339f upstream.
Change calculating of position page containing BBM
If none of BBM flags are set then function nand_bbm_get_next_page
reports EINVAL. It causes that BBM is not read at all during scanning
factory bad blocks. The result is that the BBT table is build without
checking factory BBM at all. For Micron flash memories none of these
flags are set if page size is different than 2048 bytes.
Address this regression by:
- adding NAND_BBM_FIRSTPAGE chip flag without any condition. It solves
issue only for Micron devices.
- changing the nand_bbm_get_next_page_function. It will return 0
if no of BBM flag is set and page parameter is 0. After that modification
way of discovering factory bad blocks will work similar as in kernel
version 5.1.
Cc: stable@vger.kernel.org
Fixes: f90da7818b (mtd: rawnand: Support bad block markers in first, second or last page)
Signed-off-by: Piotr Sroka <piotrs@cadence.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 69c7f4618c upstream.
Any write with either dd or flashcp to a device driven by the
spear_smi.c driver will pass through the spear_smi_cpy_toio()
function. This function will get called for chunks of up to 256 bytes.
If the amount of data is smaller, we may have a problem if the data
length is not 4-byte aligned. In this situation, the kernel panics
during the memcpy:
# dd if=/dev/urandom bs=1001 count=1 of=/dev/mtd6
spear_smi_cpy_toio [620] dest c9070000, src c7be8800, len 256
spear_smi_cpy_toio [620] dest c9070100, src c7be8900, len 256
spear_smi_cpy_toio [620] dest c9070200, src c7be8a00, len 256
spear_smi_cpy_toio [620] dest c9070300, src c7be8b00, len 233
Unhandled fault: external abort on non-linefetch (0x808) at 0xc90703e8
[...]
PC is at memcpy+0xcc/0x330
The above error occurs because the implementation of memcpy_toio()
tries to optimize the number of I/O by writing 4 bytes at a time as
much as possible, until there are less than 4 bytes left and then
switches to word or byte writes.
Unfortunately, the specification states about the Write Burst mode:
"the next AHB Write request should point to the next
incremented address and should have the same size (byte,
half-word or word)"
This means ARM architecture implementation of memcpy_toio() cannot
reliably be used blindly here. Workaround this situation by update the
write path to stick to byte access when the burst length is not
multiple of 4.
Fixes: f18dbbb1bf ("mtd: ST SPEAr: Add SMI driver for serial NOR flash")
Cc: Russell King <linux@armlinux.org.uk>
Cc: Boris Brezillon <boris.brezillon@collabora.com>
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9c8c5742b6 upstream.
platform_get_irq() calls dev_err() on an error. As the IRQ usage in the
tpm_tis driver is optional, this is undesirable.
Specifically this leads to this new false-positive error being logged:
[ 5.135413] tpm_tis MSFT0101:00: IRQ index 0 not found
This commit switches to platform_get_irq_optional(), which does not log
an error, fixing this.
Fixes: 7723f4c5ec ("driver core: platform: Add an error message to platform_get_irq*()"
Cc: <stable@vger.kernel.org> # 5.4.x
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 19e6317d24 upstream.
The problem arises because our read() function grabs a lock of the
circular buffer, finds something of interest, then invokes copy_to_user()
straight from the buffer, which in turn takes mm->mmap_sem. In the same
time, the callback mon_bin_vma_fault() is invoked under mm->mmap_sem.
It attempts to take the fetch lock and deadlocks.
This patch does away with protecting of our page list with any
semaphores, and instead relies on the kernel not close the device
while mmap is active in a process.
In addition, we prohibit re-sizing of a buffer while mmap is active.
This way, when (now unlocked) fault is processed, it works with the
page that is intended to be mapped-in, and not some other random page.
Note that this may have an ABI impact, but hopefully no legitimate
program is this wrong.
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Reported-by: syzbot+56f9673bb4cdcbeb0e92@syzkaller.appspotmail.com
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Fixes: 46eb14a6e1 ("USB: fix usbmon BUG trigger")
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20191204203941.3503452b@suzdal.zaitcev.lan
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3c11c4bed0 upstream.
Make sure to use the current alternate setting when verifying the
interface descriptors to avoid binding to an invalid interface.
Failing to do so could cause the driver to misbehave or trigger a WARN()
in usb_submit_urb() that kernels with panic_on_warn set would choke on.
Fixes: 03270634e2 ("USB: Add ADU support for Ontrak ADU devices")
Cc: stable <stable@vger.kernel.org> # 2.6.19
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20191210112601.3561-3-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7c5a2df336 upstream.
Make sure to use the current alternate setting when looking up the
endpoints on epic devices to avoid binding to an invalid interface.
Failing to do so could cause the driver to misbehave or trigger a WARN()
in usb_submit_urb() that kernels with panic_on_warn set would choke on.
Fixes: 6e8cf7751f ("USB: add EPIC support to the io_edgeport driver")
Cc: stable <stable@vger.kernel.org> # 2.6.21
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20191210112601.3561-5-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 09068c1ad5 upstream.
Make sure that the interrupt interface has an endpoint before trying to
access its endpoint descriptors to avoid dereferencing a NULL pointer.
The driver binds to the interrupt interface with interface number 0, but
must not assume that this interface or its current alternate setting are
the first entries in the corresponding configuration arrays.
Fixes: b72458a80c ("[PATCH] USB: Eagle and ADI 930 usb adsl modem driver")
Cc: stable <stable@vger.kernel.org> # 2.6.16
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20191210112601.3561-2-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 341826a065 upstream.
When a conversion result is being read from ADC, the driver reads the
number of channels + 1 because it thinks that IIO_CHAN_SOFT_TIMESTAMP
is also a physical channel. This patch fixes this issue.
Fixes: 2985a5d884 ("staging: iio: adc: ad7606: Move out of staging")
Reported-by: Robert Wörle <rwoerle@mibtec.de>
Signed-off-by: Beniamin Bia <beniamin.bia@analog.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 53eaa9c27f upstream.
Temperature should be reported in milli-degrees, not degrees. Fix
scale and offset values to use the correct unit.
This is a fix for an issue that has been present for a long time.
The fixes tag reflects the point at which the code last changed in a
fashion that would make this fix patch no longer apply. Backports
will be necessary to fix those elements that predate that patch.
Fixes: 1615fe41a1 ("iio: imu: mpu6050: Fix FIFO layout for ICM20602")
Cc: stable@vger.kernel.org
Signed-off-by: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 49549cb23a upstream.
This patch fixes the scales for the gyroscope, accelerometer and
barometer. The pressure scale was just wrong. For the others, the scale
factors were not taking into account that a 32bit word is being read
from the device.
Fixes: 7abad1063d ("iio: adis16480: Fix scale factors")
Fixes: 82e7a1b250 ("iio: imu: adis16480: Add support for ADIS1649x family of devices")
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fc3f6ad7f5 upstream.
Since st_lsm6dsx i2c master controller relies on accel device as trigger
and slave devices can run at different ODRs we must select an accel_odr >=
slave_odr. Report real accel ODR in st_lsm6dsx_check_odr() in order to
properly set sensor frequency in st_lsm6dsx_write_raw and avoid to
report unsupported frequency
Fixes: 6ffb55e500 ("iio: imu: st_lsm6dsx: introduce ST_LSM6DSX_ID_EXT sensor ids")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4c35b7a51e upstream.
The driver is defining debugfs entries by calling
`adis16480_debugfs_init()`. However, those entries are attached to the
iio_dev debugfs entry which won't exist if no debugfs_reg_access
callback is provided.
Fixes: 2f3abe6cbb ("iio:imu: Add support for the ADIS16480 and similar IMUs")
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4f9007d692 upstream.
Since v4.7 the dma initialization requires that there is a
device tree property for "rx" and "tx" channels which is
not provided by the pdata-quirks initialization.
By conversion of the mmc3 setup to device tree this will
finally allows to remove the OpenPandora wlan specific omap3
data-quirks.
Fixes: 81eef6ca92 ("mmc: omap_hsmmc: Use dma_request_chan() for requesting DMA channel")
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Cc: <stable@vger.kernel.org> # v4.7+
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bd82873f23 upstream.
spin_unlock_irqrestore() might be called with stale flags after
reading port status, possibly restoring interrupts to a incorrect
state.
If a usb2 port just finished resuming while the port status is read
the spin lock will be temporary released and re-acquired in a separate
function. The flags parameter is passed as value instead of a pointer,
not updating flags properly before the final spin_unlock_irqrestore()
is called.
Cc: <stable@vger.kernel.org> # v3.12+
Fixes: 8b3d45705e ("usb: Fix xHCI host issues on remote wakeup.")
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20191211142007.8847-7-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7ff1116280 upstream.
xhci driver claims it needs XHCI_TRUST_TX_LENGTH quirk for both
Broadcom/Cavium and a Renesas xHC controllers.
The quirk was inteded for handling false "success" complete event for
transfers that had data left untransferred.
These transfers should complete with "short packet" events instead.
In these two new cases the false "success" completion is reported
after a "short packet" if the TD consists of several TRBs.
xHCI specs 4.10.1.1.2 say remaining TRBs should report "short packet"
as well after the first short packet in a TD, but this issue seems so
common it doesn't make sense to add the quirk for all vendors.
Turn these events into short packets automatically instead.
This gets rid of the "The WARN Successful completion on short TX for
slot 1 ep 1: needs XHCI_TRUST_TX_LENGTH quirk" warning in many cases.
Cc: <stable@vger.kernel.org>
Reported-by: Eli Billauer <eli.billauer@gmail.com>
Reported-by: Ard Biesheuvel <ardb@kernel.org>
Tested-by: Eli Billauer <eli.billauer@gmail.com>
Tested-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20191211142007.8847-6-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 057d476fff upstream.
A race in xhci USB3 remote wake handling may force device back to suspend
after it initiated resume siganaling, causing a missed resume event or warm
reset of device.
When a USB3 link completes resume signaling and goes to enabled (UO)
state a interrupt is issued and the interrupt handler will clear the
bus_state->port_remote_wakeup resume flag, allowing bus suspend.
If the USB3 roothub thread just finished reading port status before
the interrupt, finding ports still in suspended (U3) state, but hasn't
yet started suspending the hub, then the xhci interrupt handler will clear
the flag that prevented roothub suspend and allow bus to suspend, forcing
all port links back to suspended (U3) state.
Example case:
usb_runtime_suspend() # because all ports still show suspended U3
usb_suspend_both()
hub_suspend(); # successful as hub->wakeup_bits not set yet
==> INTERRUPT
xhci_irq()
handle_port_status()
clear bus_state->port_remote_wakeup
usb_wakeup_notification()
sets hub->wakeup_bits;
kick_hub_wq()
<== END INTERRUPT
hcd_bus_suspend()
xhci_bus_suspend() # success as port_remote_wakeup bits cleared
Fix this by increasing roothub usage count during port resume to prevent
roothub autosuspend, and by making sure bus_state->port_remote_wakeup
flag is only cleared after resume completion is visible, i.e.
after xhci roothub returned U0 or other non-U3 link state link on a
get port status request.
Issue rootcaused by Chiasheng Lee
Cc: <stable@vger.kernel.org>
Cc: Lee, Hou-hsun <hou-hsun.lee@intel.com>
Reported-by: Lee, Chiasheng <chiasheng.lee@intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20191211142007.8847-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c724f776f0 upstream.
Make sure to use the current alternate setting when verifying the
interface descriptors to avoid binding to an invalid interface.
Failing to do so could cause the driver to misbehave or trigger a WARN()
in usb_submit_urb() that kernels with panic_on_warn set would choke on.
Fixes: 2865d42c78 ("staging: r8712u: Add the new driver to the mainline kernel")
Cc: stable <stable@vger.kernel.org> # 2.6.37
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20191210114751.5119-3-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 74ca34118a upstream.
Make sure to use the current alternate setting when verifying the
interface descriptors to avoid binding to an invalid interface.
Failing to do so could cause the driver to misbehave or trigger a WARN()
in usb_submit_urb() that kernels with panic_on_warn set would choke on.
Fixes: c2478d3907 ("staging: r8188eu: Add files for new driver - part 20")
Cc: stable <stable@vger.kernel.org> # 3.12
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20191210114751.5119-2-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1af73a25e6 upstream.
`rename_file' was exported but not properly namespaced causing a
multiple definition error because `rename_file' is already defined in
fs/hostfs/hostfs_user.c:
ld: drivers/staging/exfat/exfat_core.o: in function `rename_file':
drivers/staging/exfat/exfat_core.c:2327: multiple definition of
`rename_file'; fs/hostfs/hostfs_user.o:fs/hostfs/hostfs_user.c:350:
first defined here
make: *** [Makefile:1077: vmlinux] Error 1
This error can be reproduced on ARCH=um by selecting:
CONFIG_EXFAT_FS=y
CONFIG_HOSTFS=y
Add a namespace prefix exfat_* to fix this error.
Reported-by: Brendan Higgins <brendanhiggins@google.com>
Signed-off-by: Brendan Higgins <brendanhiggins@google.com>
Cc: stable <stable@vger.kernel.org>
Cc: Valdis Kletnieks <valdis.kletnieks@vt.edu>
Tested-by: David Gow <davidgow@google.com>
Reviewed-by: David Gow <davidgow@google.com>
Link: https://lore.kernel.org/r/20191204234522.42855-1-brendanhiggins@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e76b3bf765 upstream.
On Dell WD15 dock, sometimes USB ethernet cannot be detected after plugging
cable to the ethernet port, the hub and roothub get runtime resumed and
runtime suspended immediately:
...
[ 433.315169] xhci_hcd 0000:3a:00.0: hcd_pci_runtime_resume: 0
[ 433.315204] usb usb4: usb auto-resume
[ 433.315226] hub 4-0:1.0: hub_resume
[ 433.315239] xhci_hcd 0000:3a:00.0: Get port status 4-1 read: 0x10202e2, return 0x10343
[ 433.315264] usb usb4-port1: status 0343 change 0001
[ 433.315279] xhci_hcd 0000:3a:00.0: clear port1 connect change, portsc: 0x10002e2
[ 433.315293] xhci_hcd 0000:3a:00.0: Get port status 4-2 read: 0x2a0, return 0x2a0
[ 433.317012] xhci_hcd 0000:3a:00.0: xhci_hub_status_data: stopping port polling.
[ 433.422282] xhci_hcd 0000:3a:00.0: Get port status 4-1 read: 0x10002e2, return 0x343
[ 433.422307] usb usb4-port1: do warm reset
[ 433.422311] usb 4-1: device reset not allowed in state 8
[ 433.422339] hub 4-0:1.0: state 7 ports 2 chg 0002 evt 0000
[ 433.422346] xhci_hcd 0000:3a:00.0: Get port status 4-1 read: 0x10002e2, return 0x343
[ 433.422356] usb usb4-port1: do warm reset
[ 433.422358] usb 4-1: device reset not allowed in state 8
[ 433.422428] xhci_hcd 0000:3a:00.0: set port remote wake mask, actual port 0 status = 0xf0002e2
[ 433.422455] xhci_hcd 0000:3a:00.0: set port remote wake mask, actual port 1 status = 0xe0002a0
[ 433.422465] hub 4-0:1.0: hub_suspend
[ 433.422475] usb usb4: bus auto-suspend, wakeup 1
[ 433.426161] xhci_hcd 0000:3a:00.0: xhci_hub_status_data: stopping port polling.
[ 433.466209] xhci_hcd 0000:3a:00.0: port 0 polling in bus suspend, waiting
[ 433.510204] xhci_hcd 0000:3a:00.0: port 0 polling in bus suspend, waiting
[ 433.554051] xhci_hcd 0000:3a:00.0: port 0 polling in bus suspend, waiting
[ 433.598235] xhci_hcd 0000:3a:00.0: port 0 polling in bus suspend, waiting
[ 433.642154] xhci_hcd 0000:3a:00.0: port 0 polling in bus suspend, waiting
[ 433.686204] xhci_hcd 0000:3a:00.0: port 0 polling in bus suspend, waiting
[ 433.730205] xhci_hcd 0000:3a:00.0: port 0 polling in bus suspend, waiting
[ 433.774203] xhci_hcd 0000:3a:00.0: port 0 polling in bus suspend, waiting
[ 433.818207] xhci_hcd 0000:3a:00.0: port 0 polling in bus suspend, waiting
[ 433.862040] xhci_hcd 0000:3a:00.0: port 0 polling in bus suspend, waiting
[ 433.862053] xhci_hcd 0000:3a:00.0: xhci_hub_status_data: stopping port polling.
[ 433.862077] xhci_hcd 0000:3a:00.0: xhci_suspend: stopping port polling.
[ 433.862096] xhci_hcd 0000:3a:00.0: // Setting command ring address to 0x8578fc001
[ 433.862312] xhci_hcd 0000:3a:00.0: hcd_pci_runtime_suspend: 0
[ 433.862445] xhci_hcd 0000:3a:00.0: PME# enabled
[ 433.902376] xhci_hcd 0000:3a:00.0: restoring config space at offset 0xc (was 0x0, writing 0x20)
[ 433.902395] xhci_hcd 0000:3a:00.0: restoring config space at offset 0x4 (was 0x100000, writing 0x100403)
[ 433.902490] xhci_hcd 0000:3a:00.0: PME# disabled
[ 433.902504] xhci_hcd 0000:3a:00.0: enabling bus mastering
[ 433.902547] xhci_hcd 0000:3a:00.0: // Setting command ring address to 0x8578fc001
[ 433.902649] pcieport 0000:00:1b.0: PME: Spurious native interrupt!
[ 433.902839] xhci_hcd 0000:3a:00.0: Port change event, 4-1, id 3, portsc: 0xb0202e2
[ 433.902842] xhci_hcd 0000:3a:00.0: resume root hub
[ 433.902845] xhci_hcd 0000:3a:00.0: handle_port_status: starting port polling.
[ 433.902877] xhci_hcd 0000:3a:00.0: xhci_resume: starting port polling.
[ 433.902889] xhci_hcd 0000:3a:00.0: xhci_hub_status_data: stopping port polling.
[ 433.902891] xhci_hcd 0000:3a:00.0: hcd_pci_runtime_resume: 0
[ 433.902919] usb usb4: usb wakeup-resume
[ 433.902942] usb usb4: usb auto-resume
[ 433.902966] hub 4-0:1.0: hub_resume
...
As Mathias pointed out, the hub enters Cold Attach Status state and
requires a warm reset. However usb_reset_device() bails out early when
the device is in suspended state, as its callers port_event() and
hub_event() don't always resume the device.
Since there's nothing wrong to reset a suspended device, allow
usb_reset_device() to do so to solve the issue.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20191106062710.29880-1-kai.heng.feng@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
