[ Upstream commit 2560da49de ]
Back in the early days when gru devices were still under development
we found an issue where the WiFi reset line needed to be configured as
early as possible during the boot process to avoid the WiFi module
being in a bad state.
We found that the way to get the kernel to do this in the earliest
possible place was to configure this line in the pinctrl hogs, so
that's what we did. For some history here you can see
<http://crosreview.com/368770>. After the time that change landed in
the kernel, we landed a firmware change to configure this line even
earlier. See <http://crosreview.com/399919>. However, even after the
firmware change landed we kept the kernel change to deal with the fact
that some people working on devices might take a little while to
update their firmware.
At this there are definitely zero devices out in the wild that have
firmware without the fix in it. Specifically looking in the firmware
branch several critically important fixes for memory stability landed
after the patch in coreboot and I know we didn't ship without those.
Thus, by now, everyone should have the new firmware and it's safe to
not have the kernel set this up in a pinctrl hog.
Historically, even though it wasn't needed to have this in a pinctrl
hog, we still kept it since it didn't hurt. Pinctrl would apply the
default hog at bootup and then would never touch things again. That
all changed with commit 981ed1bfbc ("pinctrl: Really force states
during suspend/resume"). After that commit then we'll re-apply the
default hog at resume time and that can screw up the reset state of
WiFi. ...and on rk3399 if you touch a device on PCIe in the wrong way
then the whole system can go haywire. That's what was happening.
Specifically you'd resume a rk3399-gru-* device and it would mostly
resume, then would crash with some crazy weird crash.
One could say, perhaps, that the recent pinctrl change was at fault
(and should be fixed) since it changed behavior. ...but that's not
really true. The device tree for rk3399-gru is really to blame.
Specifically since the pinctrl is defined in the hog and not in the
"wlan-pd-n" node then the actual user of this pin doesn't have a
pinctrl entry for it. That's bad.
Let's fix our problems by just moving the control of
"wlan_module_reset_l pinctrl" out of the hog and put them in the
proper place.
NOTE: in theory, I think it should actually be possible to have a pin
controlled _both_ by the hog and by an actual device. Once the device
claims the pin I think the hog is supposed to let go. I'm not 100%
sure that this works and in any case this solution would be more
complex than is necessary.
Reported-by: Marc Zyngier <marc.zyngier@arm.com>
Fixes: 48f4d9796d ("arm64: dts: rockchip: add Gru/Kevin DTS")
Fixes: 981ed1bfbc ("pinctrl: Really force states during suspend/resume")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Tested-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b8b549eec8 ]
When IPsec offloading was introduced, we accidentally incremented
the sequence number counter on the xfrm_state by one packet
too much in the ESN case. This leads to a sequence number gap of
one packet after each GSO packet. Fix this by setting the sequence
number to the correct value.
Fixes: d7dbefc45c ("xfrm: Add xfrm_replay_overflow functions for offloading")
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 910f8befdf ]
Current cleanup in the error path of xen_bind_pirq_msi_to_irq is
wrong. First of all there's an off-by-one in the cleanup loop, which
can lead to unbinding wrong IRQs.
Secondly IRQs not bound won't be freed, thus leaking IRQ numbers.
Note that there's no need to differentiate between bound and unbound
IRQs when freeing them, __unbind_from_irq will deal with both of them
correctly.
Fixes: 4892c9b4ad ("xen: add support for MSI message groups")
Reported-by: Hooman Mirhadi <mirhadih@amazon.com>
Signed-off-by: Roger Pau Monné <roger.pau@citrix.com>
Reviewed-by: Amit Shah <aams@amazon.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 65389322b2 ]
IB spec says that a lid should be ignored when link layer is Ethernet,
for example when building or parsing a CM request message (CA17-34).
However, since ib_lid_be16() and ib_lid_cpu16() validates the slid,
not only when link layer is IB, we set the slid to zero to prevent
false warnings in the kernel log.
Fixes: 62ede77799 ("Add OPA extended LID support")
Reviewed-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 8a949fff03 ]
The IPS_NAT_MASK check in 4.12 replaced previous check for nfct_nat()
which was needed to fix a crash in 2.6.36-rc, see
commit 7bcbf81a22 ("ipvs: avoid oops for passive FTP").
But as IPVS does not set the IPS_SRC_NAT and IPS_DST_NAT bits,
checking for IPS_NAT_MASK prevents PASV response to be properly
mangled and blocks the transfer. Remove the check as it is not
needed after 3.12 commit 41d73ec053 ("netfilter: nf_conntrack:
make sequence number adjustments usuable without NAT") which
changes nfct_nat() with nfct_seqadj() and especially after 3.13
commit b25adce160 ("ipvs: correct usage/allocation of seqadj
ext in ipvs").
Thanks to Li Shuang and Florian Westphal for reporting the problem!
Reported-by: Li Shuang <shuali@redhat.com>
Fixes: be7be6e161 ("netfilter: ipvs: fix incorrect conflict resolution")
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Acked-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a29a252754 ]
As we have option in u-boot to set CPU mask for running linux,
we want to pass information to kernel about CPU cores should
be brought up. So we patch kernel dtb in u-boot to set
possible-cpus property.
This also allows us to have correctly setuped MCIP debug mask.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f3205de98d ]
As of today we use hardcoded MCIP debug mask, so if we launch
kernel via debugger and kick fever cores than HW has all cpus
hang at the momemt of setup MCIP debug mask.
So update MCIP debug mask when the new cpu came online, instead of
use hardcoded MCIP debug mask.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 07423d00a2 ]
In SMP systems, GFRC is used for clocksource. However by default the
counter keeps running even when core is halted (say when debugging via a
JTAG debugger). This confuses Linux timekeeping and triggers flase RCU stall
splat such as below:
| [ARCLinux]# while true; do ./shm_open_23-1.run-test ; done
| Running with 1000 processes for 1000 objects
| hrtimer: interrupt took 485060 ns
|
| create_cnt: 1000
| Running with 1000 processes for 1000 objects
| [ARCLinux]# INFO: rcu_preempt self-detected stall on CPU
| 2-...: (1 GPs behind) idle=a01/1/0 softirq=135770/135773 fqs=0
| INFO: rcu_preempt detected stalls on CPUs/tasks:
| 0-...: (1 GPs behind) idle=71e/0/0 softirq=135264/135264 fqs=0
| 2-...: (1 GPs behind) idle=a01/1/0 softirq=135770/135773 fqs=0
| 3-...: (1 GPs behind) idle=4e0/0/0 softirq=134304/134304 fqs=0
| (detected by 1, t=13648 jiffies, g=31493, c=31492, q=1)
Starting from ARC HS v3.0 it's possible to tie GFRC to state of up-to 4
ARC cores with help of GFRC's CORE register where we set a mask for
cores which state we need to rely on.
We update cpu mask every time new cpu came online instead of using
hardcoded one or using mask generated from "possible_cpus" as we
want it set correctly even if we run kernel on HW which has fewer cores
than expected (or we launch kernel via debugger and kick fever cores
than HW has)
Note that GFRC halts when all cores have halted and thus relies on
programming of Inter-Core-dEbug register to halt all cores when one
halts.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
[vgupta: rewrote changelog]
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b3529af6bb ]
One of the basic construct in the device is a port-VLAN pair, which can
be bound to a FID or a RIF in order to direct packets to the bridge or
the router, respectively.
Since not all the netdevs are configured with a VLAN (e.g., sw1p1 vs.
sw1p1.10), VID 1 is used to represent these and thus this VID can be
used by both upper devices of mlxsw ports and by the driver itself.
However, this VID is not reference counted and therefore might be freed
prematurely, which can result in various WARNINGs. For example:
$ ip link add name br0 type bridge vlan_filtering 1
$ teamd -t team0 -d -c '{"runner": {"name": "lacp"}}'
$ ip link set dev team0 master br0
$ ip link set dev enp1s0np1 master team0
$ ip address add 192.0.2.1/24 dev enp1s0np1
The enslavement to team0 will fail because team0 already has an upper
and thus vlan_vids_del_by_dev() will be executed as part of team's error
path which will delete VID 1 from enp1s0np1 (added by br0 as PVID). The
WARNING will be generated when the driver will realize it can't find VID
1 on the port and bind it to a RIF.
Fix this by adding a reference count to the VLAN entries on the port, in
a similar fashion to the reference counting used by the corresponding
'vlan_vid_info' structure in the 8021q driver.
Fixes: c57529e1d5 ("mlxsw: spectrum: Replace vPorts with Port-VLAN")
Reported-by: Tal Bar <talb@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Tested-by: Tal Bar <talb@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9d45deb04c ]
When multicast snooping is enabled, the Linux bridge resorts to flooding
unregistered multicast packets to all ports only in case it did not
detect a querier in the network.
The above condition is not reflected to underlying drivers, which is
especially problematic in IPv6 environments, as multicast snooping is
enabled by default and since neighbour solicitation packets might be
treated as unregistered multicast packets in case there is no
corresponding MDB entry.
Until the Linux bridge reflects its querier state to underlying drivers,
simply treat unregistered multicast packets as broadcast and allow them
to reach their destination.
Fixes: 9df552ef3e ("mlxsw: spectrum: Improve IPv6 unregistered multicast flooding")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2ddc94c76c ]
IP_TTL, IP_ECN and IP_DSCP are using the same offset within the
scratchpad as L4 ports. Fix this by shifting all up.
Fixes: 5f57e09091 ("mlxsw: acl: Add ip ttl acl element")
Fixes: i80d0fe4710c ("mlxsw: acl: Add ip tos acl element")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit bffd2b6167 ]
PSDT field section according to NVM_Express-1.3:
"This field specifies whether PRPs or SGLs are used for any data
transfer associated with the command. PRPs shall be used for all
Admin commands for NVMe over PCIe. SGLs shall be used for all Admin
and I/O commands for NVMe over Fabrics. This field shall be set to
01b for NVMe over Fabrics 1.0 implementations.
Suggested-by: Idan Burstein <idanb@mellanox.com>
Signed-off-by: Max Gurtovoy <maxg@mellanox.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 590399ddf9 ]
Don't include in the Rx bytecount of the packet sent up the stack:
the FCB (frame control block), and the padding bytes inserted by
the controller into the frame payload, nor the FCS. All these are
being pulled out of the skb by gfar_process_frame().
This issue is old, likely from the driver's beginnings, however
it was amplified by recent:
commit d903ec7711 ("gianfar: simplify FCS handling and fix memory leak")
which basically added the FCS to the Rx bytecount, and so brought
this to my attention.
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 64c3f648c2 ]
Once in a while I see build errors similar to the following
when building images from a clean tree.
Building powerpc:virtex-ml507:44x/virtex5_defconfig ... failed
------------
Error log:
arch/powerpc/boot/treeboot-akebono.c:37:20: fatal error:
libfdt.h: No such file or directory
Building powerpc:bamboo:smpdev:44x/bamboo_defconfig ... failed
------------
Error log:
arch/powerpc/boot/treeboot-akebono.c:37:20: fatal error:
libfdt.h: No such file or directory
arch/powerpc/boot/treeboot-currituck.c:35:20: fatal error:
libfdt.h: No such file or directory
Rebuilds will succeed.
Turns out that several source files in arch/powerpc/boot/ include
libfdt.h, but Makefile dependencies are incomplete. Let's fix that.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0a5aff64f2 ]
Jon attempted to fix the amount of RAM on the BCM958625HR in commit
c53beb47f6 ("ARM: dts: NSP: Correct RAM amount for BCM958625HR board")
but it seems like we tripped over some poorly documented schematics.
The top-level page of the schematics says the board has 2GB, but when
you end-up scrolling to page 6, you see two chips of 4GBit (512MB) but
what the bootloader really initializes only 512MB, any attempt to use
more than that results in data aborts. Fix this again back to 512MB.
Fixes: c53beb47f6 ("ARM: dts: NSP: Correct RAM amount for BCM958625HR board")
Acked-by: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0979962f54 ]
It seems that the proper value to return in this particular case is the
one contained into variable new_index instead of ret.
Addresses-Coverity-ID: 1465148 ("Copy-paste error")
Fixes: e46c7287b1 ("nbd: add a basic netlink interface")
Reviewed-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2b3957c34b ]
Commit 128bb975dc ("ip6_gre: init dev->mtu and dev->hard_header_len
correctly") fixed IFLA_MTU ignored on NEWLINK for ip6_gre. The same
mtu fix is also needed for sit.
Note that dev->hard_header_len setting for sit works fine, no need to
fix it. sit is actually ipv4 tunnel, it can't call ip6_tnl_change_mtu
to set mtu.
Reported-by: Jianlin Shi <jishi@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a6aa804462 ]
Commit 128bb975dc ("ip6_gre: init dev->mtu and dev->hard_header_len
correctly") fixed IFLA_MTU ignored on NEWLINK for ip6_gre. The same
mtu fix is also needed for ip6_tunnel.
Note that dev->hard_header_len setting for ip6_tunnel works fine,
no need to fix it.
Reported-by: Jianlin Shi <jishi@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ffc2b6ee41 ]
It's safe to remove the setting of dev's needed_headroom and mtu in
__gre_tunnel_init, as discussed in [1], ip_tunnel_newlink can do it
properly.
Now Eric noticed that it could cover the mtu value set in do_setlink
when creating a ip_gre dev. It makes IFLA_MTU param not take effect.
So this patch is to remove them to make IFLA_MTU work, as in other
ipv4 tunnels.
[1]: https://patchwork.ozlabs.org/patch/823504/
Fixes: c544193214 ("GRE: Refactor GRE tunneling code.")
Reported-by: Eric Garver <e@erig.me>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 4c27bf3c5b ]
r8152 driver handles TSO packets (limited to ~16KB) quite well,
but pretends each TSO logical packet is a single packet on the wire.
There is also some error since headers are accounted once, but
error rate is small enough that we do not care.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 067b25a563 ]
The Makefile lacks a couple of line continuation backslashes
in an `if' clause, which produces an error when make versions
prior to 4.x are used for building the tests.
$ make
make[1]: Entering directory `/[...]/linux/tools/testing/selftests/futex'
/bin/sh: -c: line 5: syntax error: unexpected end of file
make[1]: *** [all] Error 1
make[1]: Leaving directory `/[...]/linux/tools/testing/selftests/futex'
make: *** [all] Error 2
Signed-off-by: Daniel Díaz <daniel.diaz@linaro.org>
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 13a55372b6 ]
It is not valid for orion5x to use mac_pton().
First of all, the orion5x buffer is not NULL terminated. mac_pton()
has no business operating on non-NULL terminated buffers because
only the caller can know that this is valid and in what manner it
is ok to parse this NULL'less buffer.
Second of all, orion5x operates on an __iomem pointer, which cannot
be dereferenced using normal C pointer operations. Accesses to
such areas much be performed with the proper iomem accessors.
Fixes: 4904dbda41 ("ARM: orion5x: use mac_pton() helper")
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 68d2059be6 ]
Currently if map is null then a potential null pointer deference
occurs when calling sock_release on map->sock. I believe the
actual intention was to call sock_release on sock instead. Fix
this.
Fixes: 5db4d286a8 ("xen/pvcalls: implement connect command")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 18106734b5 ]
When failing from ceph_fs_debugfs_init() in ceph_real_mount(),
there is lack of dput of root_dentry and it causes slab errors,
so change the calling order of ceph_fs_debugfs_init() and
open_root_dentry() and do some cleanups to avoid this issue.
Signed-off-by: Chengguang Xu <cgxu519@icloud.com>
Reviewed-by: "Yan, Zheng" <zyan@redhat.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f25a2dfc20 ]
This patch fixes nvme queue cleanup if requesting an IRQ handler for
the queue's vector fails. It does this by resetting the cq_vector to
the uninitialized value of -1 so it is ignored for a controller reset.
Signed-off-by: Jianchao Wang <jianchao.w.wang@oracle.com>
[changelog updates, removed misc whitespace changes]
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit fce672db54 ]
The function batadv_bla_backbone_dump_bucket must be able to handle
non-complete dumps of a single bucket. It tries to do that by saving the
latest dumped index in *idx_skip to inform the caller about the current
state.
But the caller only assumes that buckets were not completely dumped when
the return code is non-zero. This function must therefore also return a
non-zero index when the dumping of an entry failed. Otherwise the caller
will just skip all remaining buckets.
And the function must also reset *idx_skip back to zero when it finished a
bucket. Otherwise it will skip the same number of entries in the next
bucket as the previous one had.
Fixes: ea4152e117 ("batman-adv: add backbone table netlink support")
Reported-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b0264ecdfe ]
The function batadv_bla_claim_dump_bucket must be able to handle
non-complete dumps of a single bucket. It tries to do that by saving the
latest dumped index in *idx_skip to inform the caller about the current
state.
But the caller only assumes that buckets were not completely dumped when
the return code is non-zero. This function must therefore also return a
non-zero index when the dumping of an entry failed. Otherwise the caller
will just skip all remaining buckets.
And the function must also reset *idx_skip back to zero when it finished a
bucket. Otherwise it will skip the same number of entries in the next
bucket as the previous one had.
Fixes: 04f3f5bf18 ("batman-adv: add B.A.T.M.A.N. Dump BLA claims via netlink")
Reported-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 011c935fce ]
The function batadv_v_gw_dump stops the processing loop when
batadv_v_gw_dump_entry returns a non-0 return code. This should only
happen when the buffer is full. Otherwise, an empty message may be
returned by batadv_gw_dump. This empty message will then stop the netlink
dumping of gateway entries. At worst, not a single entry is returned to
userspace even when plenty of possible gateways exist.
Fixes: b71bb6f924 ("batman-adv: add B.A.T.M.A.N. V bat_gw_dump implementations")
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 10d5702842 ]
The function batadv_iv_gw_dump stops the processing loop when
batadv_iv_gw_dump_entry returns a non-0 return code. This should only
happen when the buffer is full. Otherwise, an empty message may be
returned by batadv_gw_dump. This empty message will then stop the netlink
dumping of gateway entries. At worst, not a single entry is returned to
userspace even when plenty of possible gateways exist.
Fixes: efb766af06 ("batman-adv: add B.A.T.M.A.N. IV bat_gw_dump implementations")
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1a9da59373 ]
Once struct is added to per-netns list it becomes visible to other cpus,
so we cannot use kfree().
Also delay setting entries refcount to 1 until after everything is
initialised so that when we call clusterip_config_put() in this spot
entries is still zero.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3bf2a09da9 ]
A more sophisticated implementation could try to combine fragment checksums
when all fragments have CHECKSUM_COMPLETE and are split at even offsets.
For now, we just set ip_summed to CHECKSUM_NONE to avoid "hw csum failure"
warnings in the kernel log when fragmented frames are received. In
consequence, skb_pull_rcsum() can be replaced with skb_pull().
Note that in usual setups, packets don't reach batman-adv with
CHECKSUM_COMPLETE (I assume NICs bail out of checksumming when they see
batadv's ethtype?), which is why the log messages do not occur on every
system using batman-adv. I could reproduce this issue by stacking
batman-adv on top of a VXLAN interface.
Fixes: 610bfc6bc9 ("batman-adv: Receive fragmented packets and merge")
Tested-by: Maximilian Wilhelm <max@sdn.clinic>
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit abd6360591 ]
eth_type_trans() internally calls skb_pull(), which does not adjust the
skb checksum; skb_postpull_rcsum() is necessary to avoid log spam of the
form "bat0: hw csum failure" when packets with CHECKSUM_COMPLETE are
received.
Note that in usual setups, packets don't reach batman-adv with
CHECKSUM_COMPLETE (I assume NICs bail out of checksumming when they see
batadv's ethtype?), which is why the log messages do not occur on every
system using batman-adv. I could reproduce this issue by stacking
batman-adv on top of a VXLAN interface.
Fixes: c6c8fea297 ("net: Add batman-adv meshing protocol")
Tested-by: Maximilian Wilhelm <max@sdn.clinic>
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 8876391e44 ]
There is a potential deadlock if mount/umount happens when
raid5_finish_reshape() tries to grow the size of emulated disk.
How the deadlock happens?
1) The raid5 resync thread finished reshape (expanding array).
2) The mount or umount thread holds VFS sb->s_umount lock and tries to
write through critical data into raid5 emulated block device. So it
waits for raid5 kernel thread handling stripes in order to finish it
I/Os.
3) In the routine of raid5 kernel thread, md_check_recovery() will be
called first in order to reap the raid5 resync thread. That is,
raid5_finish_reshape() will be called. In this function, it will try
to update conf and call VFS revalidate_disk() to grow the raid5
emulated block device. It will try to acquire VFS sb->s_umount lock.
The raid5 kernel thread cannot continue, so no one can handle mount/
umount I/Os (stripes). Once the write-through I/Os cannot be finished,
mount/umount will not release sb->s_umount lock. The deadlock happens.
The raid5 kernel thread is an emulated block device. It is responible to
handle I/Os (stripes) from upper layers. The emulated block device
should not request any I/Os on itself. That is, it should not call VFS
layer functions. (If it did, it will try to acquire VFS locks to
guarantee the I/Os sequence.) So we have the resync thread to send
resync I/O requests and to wait for the results.
For solving this potential deadlock, we can put the size growth of the
emulated block device as the final step of reshape thread.
2017/12/29:
Thanks to Guoqing Jiang <gqjiang@suse.com>,
we confirmed that there is the same deadlock issue in raid10. It's
reproducible and can be fixed by this patch. For raid10.c, we can remove
the similar code to prevent deadlock as well since they has been called
before.
Reported-by: Alex Wu <alexwu@synology.com>
Reviewed-by: Alex Wu <alexwu@synology.com>
Reviewed-by: Chung-Chiang Cheng <cccheng@synology.com>
Signed-off-by: BingJing Chang <bingjingc@synology.com>
Signed-off-by: Shaohua Li <sh.li@alibaba-inc.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
