Fixes for omap variants for v5.5-rc1 cycle
This series of changes contains fixes for issues recently noticed:
- The ti-sysc interconnect target module driver needs fixes for
mstandby quirk handling and reset delay
- We need to configure am335x-sancloud-bbe to use rgmii-id mode because of
the phy changes done earlier
- NET_SWITCHDEV is no longer selected in Kconfig but a dependency and we
must enable CONFIG_NET_SWITCHDEV to have TI_CPSW_SWITCHDEV
- We are still relying on DEBUG_FS at least for PM configuration, let's
add it back
- We need to update compatible for am437x-gp/epos-evm because of the
recent changes to use generic panels
* tag 'omap-for-v5.5/fixes-rc1-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
bus: ti-sysc: Fix missing reset delay handling
ARM: dts: am437x-gp/epos-evm: fix panel compatible
ARM: omap2plus_defconfig: Add back DEBUG_FS
ARM: omap2plus_defconfig: enable NET_SWITCHDEV
ARM: dts: am335x-sancloud-bbe: fix phy mode
bus: ti-sysc: Fix missing force mstandby quirk handling
Link: https://lore.kernel.org/r/pull-1576254925-709310@atomide.com
Signed-off-by: Olof Johansson <olof@lixom.net>
Since commit 0e4a459f56 ("tracing: Remove unnecessary DEBUG_FS
dependency"), CONFIG_DEBUG_FS is no longer auto-enabled. This breaks
booting Debian 9, as systemd needs debugfs:
[FAILED] Failed to mount /sys/kernel/debug.
See 'systemctl status sys-kernel-debug.mount' for details.
[DEPEND] Dependency failed for Local File Systems.
...
You are in emergGive root password for maintenance
(or press Control-D to continue):
Fix this by enabling CONFIG_DEBUG_FS explicitly.
See also commit 18977008f4 ("ARM: multi_v7_defconfig: Restore
debugfs support").
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/20191209101327.26571-1-geert+renesas@glider.be
i.MX fixes for 5.5:
- Add missing jedec,spi-nor compatible for imx6ul-14x14-evk board,
so that SPI NOR device can be probed.
- Fix power button of E60K02 board by removing LDORTC2 regulator.
- A couple of fixes on serial number support of i.MX6ULL/ULZ SoCs to
remove the boot regression caused by 8267ff89b7 ("ARM: imx: Add
serial number support for i.MX6/7 SoCs").
- A couple of fixes on LS1028A SoC TMU regarding to calibration data
and reboot register configuration.
- Fix a regression seen on imx6ul-evk board by marking always-on for
the regulator that is shared by many peripherals.
- Explicitly restore CONFIG_DEBUG_FS in imx_v6_v7_defconfig.
* tag 'imx-fixes-5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: imx: Fix boot crash if ocotp is not found
ARM: imx_v6_v7_defconfig: Explicitly restore CONFIG_DEBUG_FS
ARM: dts: imx6ul-evk: Fix peripheral regulator
arm64: dts: ls1028a: fix reboot node
arm64: dts: ls1028a: fix typo in TMU calibration data
ARM: imx: Correct ocotp id for serial number support of i.MX6ULL/ULZ SoCs
ARM: dts: e60k02: fix power button
ARM: dts: imx6ul: imx6ul-14x14-evk.dtsi: Fix SPI NOR probing
Link: https://lore.kernel.org/r/20191212122427.GK15858@dragon
Signed-off-by: Olof Johansson <olof@lixom.net>
We have dts property for "ti,sysc-delay-us", and we're using it, but the
wait after OCP softreset only happens if devices are probed in legacy mode.
Let's add a delay after writing the OCP softreset when specified.
Fixes: e0db94fe87 ("bus: ti-sysc: Make OCP reset work for sysstatus and sysconfig reset bits")
Cc: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The imx_soc_device_init functions tries to fetch the ocotp regmap in
order to soc serial number. If regmap fetch fails then a message is
printed but regmap_read is called anyway and the system crashes.
Failing to lookup ocotp regmap shouldn't be a fatal boot error so check
that the pointer is valid.
Only side-effect of ocotp lookup failure now is that serial number will
be reported as all-zeros which is acceptable.
Cc: stable@vger.kernel.org
Fixes: 8267ff89b7 ("ARM: imx: Add serial number support for i.MX6/7 SoCs")
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Tested-by: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This is currently off and that's not desirable: default imx config is
meant to be generally useful for development and debugging.
Running git bisect between v5.4 and v5.5-rc1 finds this started from
commit 0e4a459f56 ("tracing: Remove unnecessary DEBUG_FS dependency")
Explicit CONFIG_DEBUG_FS=y was earlier removed by
commit c29d541f59 ("ARM: imx_v6_v7_defconfig: Remove unneeded options")
A very similar fix was required before:
commit 7e9eb62688 ("ARM: imx_v6_v7_defconfig: Explicitly restore CONFIG_DEBUG_FS")
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Many peripherals are affected by gpio5/2, not just sensors. One of those
is ethernet phy so network boot is current broken.
Fix by renaming reg_sensors and marking it as "always on". Also add a
comment asking for careful testing if this is to be made dynamic in the
future.
The "peri_3v3" naming is similar to imx6sx-sdb and regulator-name is
same string as in schematics (VPERI_3V3).
Fixes: 09e2b10489 ("ARM: dts: imx6ul-14x14-evk: Add sensors' GPIO regulator")
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The reboot register isn't located inside the DCFG controller, but in its
own RST controller. Fix it.
Fixes: 8897f3255c ("arm64: dts: Add support for NXP LS1028A SoC")
Signed-off-by: Michael Walle <michael@walle.cc>
Acked-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Reset controller fixes for v5.5, part 2
Fix the example in the brcmstb-reset device tree bindings, remove a bogus
resource alignment check from the reset-brcmstb driver, fix the documented
return value type for the reset_control_array_get functions, and fix a
devres memory leak when requesting optional, not present reset controls.
* tag 'reset-fixes-for-v5.5-2' of git://git.pengutronix.de/git/pza/linux:
reset: Do not register resource data for missing resets
reset: Fix {of,devm}_reset_control_array_get kerneldoc return types
reset: brcmstb: Remove resource checks
dt-bindings: reset: Fix brcmstb-reset example
Link: https://lore.kernel.org/r/bb59b9f83892aa3c876f5da87890b0496f2dc755.camel@pengutronix.de
Signed-off-by: Olof Johansson <olof@lixom.net>
This pull request contains Broadcom ARM-based SoCs Device Tree fixes for
v5.5-rc1, please pull the following:
- Nicolas fixes the SoC's dma-range property to cover the full 1GB
aperture
- Stefan fixes the critical temperature trip point to be set before the
firmware performs thermal throttling
- Florian fixes the BCM5301X and Cygnus MDIO nodes to have corrected
#address-cells and #size-cells properties
* tag 'arm-soc/for-5.5/devicetree-fixes' of https://github.com/Broadcom/stblinux:
ARM: dts: bcm283x: Fix critical trip point
ARM: dts: Cygnus: Fix MDIO node address/size cells
ARM: dts: bcm2711: fix soc's node dma-ranges
ARM: dts: BCM5301X: Fix MDIO node address/size cells
Link: https://lore.kernel.org/r/20191210205850.12442-1-f.fainelli@gmail.com
Signed-off-by: Olof Johansson <olof@lixom.net>
The file was moved, causing a build error:
In file included from /git/arm-soc/arch/arm/mach-mmp/pxa168.c:28:
arch/arm/mach-mmp/pxa168.h:22:10: fatal error: cputype.h: No such file or directory
Include it from the new location.
Link: https://lore.kernel.org/r/20191210203409.2875880-1-arnd@arndb.de
Fixes: 32adcaa010 ("ARM: mmp: move cputype.h to include/linux/soc/")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Olof Johansson <olof@lixom.net>
The LCD panel on AM4 GP EVMs and ePOS boards seems to be
osd070t1718-19ts. The current dts files say osd057T0559-34ts. Possibly
the panel has changed since the early EVMs, or there has been a mistake
with the panel type.
Update the DT files accordingly.
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The temperature sensor may jump backwards because there is a wrong
calibration value. Both values have to be monotonically increasing.
Fix it.
This was tested on a custom board.
Fixes: 571cebfe8e ("arm64: dts: ls1028a: Add Thermal Monitor Unit node")
Signed-off-by: Michael Walle <michael@walle.cc>
Acked-by: Tang Yuantian <andy.tang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
After the commit 8267ff89b7 ("ARM: imx: Add serial number support for i.MX6/7 SoCs")
the kernel doesn't start on i.MX6ULL/ULZ SoC.
Tested on next-20191205.
For i.MX6ULL/ULZ the variable "ocotp_compat" is set to "fsl,imx6ul-ocotp", but with commit
ffbc34bf0e ("nvmem: imx-ocotp: Implement i.MX6ULL/ULZ support") and commit
f243bc821e ("ARM: dts: imx6ull: Fix i.MX6ULL/ULZ ocotp compatible") the value
"fsl,imx6ull-ocotp" is already defined and set in device tree...
By setting "ocotp_compat" to "fsl,imx6ull-ocotp" the kernel does boot.
Fixes: 8267ff89b7 ("ARM: imx: Add serial number support for i.MX6/7 SoCs")
Signed-off-by: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
During definition of the CPU thermal zone of BCM283x SoC family there
was a misunderstanding of the meaning "criticial trip point" and the
thermal throttling range of the VideoCore firmware. The latter one takes
effect when the core temperature is at least 85 degree celsius or higher
So the current critical trip point doesn't make sense, because the
thermal shutdown appears before the firmware has a chance to throttle
the ARM core(s).
Fix these unwanted shutdowns by increasing the critical trip point
to a value which shouldn't be reached with working thermal throttling.
Fixes: 0fe4d2181c ("ARM: dts: bcm283x: Add CPU thermal zone with 1 trip point")
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Commit 0e4a459f56 ("tracing: Remove unnecessary DEBUG_FS dependency")
removed select for DEBUG_FS but we still need it at least for enabling
deeper idle states for the SoCs.
Signed-off-by: Tony Lindgren <tony@atomide.com>
The TI_CPSW_SWITCHDEV definition in Kconfig was changed from "select
NET_SWITCHDEV" to "depends on NET_SWITCHDEV", and therefore it is required
to explicitelly enable NET_SWITCHDEV config option in omap2plus_defconfig.
Fixes: 3727d259dd ("arm: omap2plus_defconfig: enable new cpsw switchdev driver")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The phy mode should be rgmii-id. For some reason, it used to work with
rgmii-txid but doesn't any more.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit 03856e928b ("bus: ti-sysc: Handle mstandby quirk and use it for
musb") added quirk handling for mstandby quirk but did not consider that
we also need a quirk variant for SYSC_QUIRK_FORCE_MSTANDBY.
We need to use forced idle mode for both SYSC_QUIRK_SWSUP_MSTANDBY and
SYSC_QUIRK_FORCE_MSTANDBY, but SYSC_QUIRK_SWSUP_MSTANDBY also need to
additionally also configure no-idle mode when enabled.
Fixes: 03856e928b ("bus: ti-sysc: Handle mstandby quirk and use it for musb")
Signed-off-by: Tony Lindgren <tony@atomide.com>
When an optional reset is not present, __devm_reset_control_get() and
devm_reset_control_array_get() still register resource data to release
the non-existing reset on cleanup, which is futile.
Fix this by skipping NULL reset control pointers.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
of_reset_control_array_get() and devm_reset_control_array_get() return
struct reset_control pointers, not internal struct reset_control_array
pointers, just like all other reset control API calls.
Correct the kerneldoc to match the code.
Fixes: 17c82e206d ("reset: Add APIs to manage array of resets")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
The use of IS_ALIGNED() is incorrect, the typical resource we pass looks
like this: start: 0x8404318, size: 0x30. When using IS_ALIGNED() we will
get the following 0x8404318 & (0x18 - 1) = 0x10 which is definitively
not equal to 0, same goes with the size. These two checks would make the
driver fail probing.
Remove the resource checks, since there should be no constraint on the
base addresse or size.
Fixes: 77750bc089 ("reset: Add Broadcom STB SW_INIT reset controller driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
The reset controller has a #reset-cells value of 1, so we should see a
phandle plus a register identifier, fix the example.
Fixes: 0807caf647 ("dt-bindings: reset: Add document for Broadcom STB reset controller")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Raspberry Pi's firmware has a feature to select how much memory to
reserve for its GPU called 'gpu_mem'. The possible values go from 16MB
to 944MB, with a default of 64MB. This memory resides in the topmost
part of the lower 1GB memory area and grows bigger expanding towards the
begging of memory.
It turns out that with low 'gpu_mem' values (16MB and 32MB) the size of
the memory available to the system in the lower 1GB area can outgrow the
interconnect's dma-range as its size was selected based on the maximum
system memory available given the default gpu_mem configuration. This
makes that memory slice unavailable for DMA. And may cause nasty kernel
warnings if CMA happens to include it.
Change soc's dma-ranges to really reflect it's HW limitation, which is
being able to only DMA to the lower 1GB area.
Fixes: 7dbe8c62ce ("ARM: dts: Add minimal Raspberry Pi 4 support")
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Reviewed-by: Phil Elwell <phil@raspberrypi.org>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The MDIO node on BCM5301X had an reversed #address-cells and
#size-cells properties, correct those, silencing checker warnings:
.../linux/arch/arm/boot/dts/bcm4708-asus-rt-ac56u.dt.yaml: mdio@18003000: #address-cells:0:0: 1 was expected
Reported-by: Simon Horman <simon.horman@netronome.com>
Fixes: 23f1eca6d5 ("ARM: dts: BCM5301X: Specify MDIO bus in the DT")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
ARMv7 Vexpress fixes for v5.5
Switching the cpumask from topology core to OPP sharing, as the topology
core cpumask can be modified during cpu hotplug to avoid setting up
wrong cpufreq policy cpumask.
* tag 'vexpress-fixes-5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
cpufreq: vexpress-spc: Switch cpumask from topology core to OPP sharing
ARM: vexpress: Set-up shared OPP table instead of individual for each CPU
Link: https://lore.kernel.org/r/20191209140037.GC25155@bogus
Signed-off-by: Olof Johansson <olof@lixom.net>
Since commit ca74b316df ("arm: Use common cpu_topology structure and
functions.") the core cpumask has to be modified during cpu hotplug
operations. So using them to set up cpufreq policy cpumask may be
incorrect as it may contain only cpus that are online at that instance.
Instead, we can use the cpumask setup by OPP library that contains all
the cpus sharing OPP table using dev_pm_opp_get_sharing_cpus.
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Tested-by: Dietmar Eggemann <dietmar.eggemann@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Currently we add individual copy of same OPP table for each CPU within
the cluster. This is redundant and doesn't reflect the reality.
We can't use core cpumask to set policy->cpus in ve_spc_cpufreq_init()
anymore as it gets called via cpuhp_cpufreq_online()->cpufreq_online()
->cpufreq_driver->init() and the cpumask gets updated upon CPU hotplug
operations. It also may cause issues when the vexpress_spc_cpufreq
driver is built as a module.
Since ve_spc_clk_init is built-in device initcall, we should be able to
use the same topology_core_cpumask to set the opp sharing cpumask via
dev_pm_opp_set_sharing_cpus and use the same later in the driver via
dev_pm_opp_get_sharing_cpus.
Cc: Liviu Dudau <liviu.dudau@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Tested-by: Dietmar Eggemann <dietmar.eggemann@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
The power button was only producing irqs, but no key events,
Forced power down with long key press works, so probably
only a short spike arrives at the SoC.
Further investigation shows that LDORTC2 is off after boot
of the vendor kernel. LDORTC2 is shared with a GPIO at the pmic
which probably transfers the button press to the SoC.
That regulator off at boot, so "regulator-boot-on" is definitively
wrong. So remove that.
Reported-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Fixes: c100ea86e6 ("ARM: dts: add Netronix E60K02 board common file")
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Without this "jedec,spi-nor" compatible property, probing of the SPI NOR
does not work on the NXP i.MX6ULL EVK. Fix this by adding this
compatible property to the DT.
Fixes: 7d77b8505a ("ARM: dts: imx6ull: fix the imx6ull-14x14-evk configuration")
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Pull networking fixes from David Miller:
1) More jumbo frame fixes in r8169, from Heiner Kallweit.
2) Fix bpf build in minimal configuration, from Alexei Starovoitov.
3) Use after free in slcan driver, from Jouni Hogander.
4) Flower classifier port ranges don't work properly in the HW offload
case, from Yoshiki Komachi.
5) Use after free in hns3_nic_maybe_stop_tx(), from Yunsheng Lin.
6) Out of bounds access in mqprio_dump(), from Vladyslav Tarasiuk.
7) Fix flow dissection in dsa TX path, from Alexander Lobakin.
8) Stale syncookie timestampe fixes from Guillaume Nault.
[ Did an evil merge to silence a warning introduced by this pull - Linus ]
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (84 commits)
r8169: fix rtl_hw_jumbo_disable for RTL8168evl
net_sched: validate TCA_KIND attribute in tc_chain_tmplt_add()
r8169: add missing RX enabling for WoL on RTL8125
vhost/vsock: accept only packets with the right dst_cid
net: phy: dp83867: fix hfs boot in rgmii mode
net: ethernet: ti: cpsw: fix extra rx interrupt
inet: protect against too small mtu values.
gre: refetch erspan header from skb->data after pskb_may_pull()
pppoe: remove redundant BUG_ON() check in pppoe_pernet
tcp: Protect accesses to .ts_recent_stamp with {READ,WRITE}_ONCE()
tcp: tighten acceptance of ACKs not matching a child socket
tcp: fix rejected syncookies due to stale timestamps
lpc_eth: kernel BUG on remove
tcp: md5: fix potential overestimation of TCP option space
net: sched: allow indirect blocks to bind to clsact in TC
net: core: rename indirect block ingress cb function
net-sysfs: Call dev_hold always in netdev_queue_add_kobject
net: dsa: fix flow dissection on Tx path
net/tls: Fix return values to avoid ENOTSUPP
net: avoid an indirect call in ____sys_recvmsg()
...
Pull more SCSI updates from James Bottomley:
"Eleven patches, all in drivers (no core changes) that are either minor
cleanups or small fixes.
They were late arriving, but still safe for -rc1"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: MAINTAINERS: Add the linux-scsi mailing list to the ISCSI entry
scsi: megaraid_sas: Make poll_aen_lock static
scsi: sd_zbc: Improve report zones error printout
scsi: qla2xxx: Fix qla2x00_request_irqs() for MSI
scsi: qla2xxx: unregister ports after GPN_FT failure
scsi: qla2xxx: fix rports not being mark as lost in sync fabric scan
scsi: pm80xx: Remove unused include of linux/version.h
scsi: pm80xx: fix logic to break out of loop when register value is 2 or 3
scsi: scsi_transport_sas: Fix memory leak when removing devices
scsi: lpfc: size cpu map by last cpu id set
scsi: ibmvscsi_tgt: Remove unneeded variable rc
Pull cifs fixes from Steve French:
"Nine cifs/smb3 fixes:
- one fix for stable (oops during oplock break)
- two timestamp fixes including important one for updating mtime at
close to avoid stale metadata caching issue on dirty files (also
improves perf by using SMB2_CLOSE_FLAG_POSTQUERY_ATTRIB over the
wire)
- two fixes for "modefromsid" mount option for file create (now
allows mode bits to be set more atomically and accurately on create
by adding "sd_context" on create when modefromsid specified on
mount)
- two fixes for multichannel found in testing this week against
different servers
- two small cleanup patches"
* tag '5.5-rc-smb3-fixes-part2' of git://git.samba.org/sfrench/cifs-2.6:
smb3: improve check for when we send the security descriptor context on create
smb3: fix mode passed in on create for modetosid mount option
cifs: fix possible uninitialized access and race on iface_list
cifs: Fix lookup of SMB connections on multichannel
smb3: query attributes on file close
smb3: remove unused flag passed into close functions
cifs: remove redundant assignment to pointer pneg_ctxt
fs: cifs: Fix atime update check vs mtime
CIFS: Fix NULL-pointer dereference in smb2_push_mandatory_locks
Pull misc vfs cleanups from Al Viro:
"No common topic, just three cleanups".
* 'work.misc' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
make __d_alloc() static
fs/namespace: add __user to open_tree and move_mount syscalls
fs/fnctl: fix missing __user in fcntl_rw_hint()
Pull NTB update from Jon Mason:
"Just a simple patch to add a new Hygon Device ID to the AMD NTB device
driver"
* tag 'ntb-5.5' of git://github.com/jonmason/ntb:
NTB: Add Hygon Device ID
Pull more input updates from Dmitry Torokhov:
- fixups for Synaptics RMI4 driver
- a quirk for Goodinx touchscreen on Teclast tablet
- a new keycode definition for activating privacy screen feature found
on a few "enterprise" laptops
- updates to snvs_pwrkey driver
- polling uinput device for writing (which is always allowed) now works
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: synaptics-rmi4 - don't increment rmiaddr for SMBus transfers
Input: synaptics-rmi4 - re-enable IRQs in f34v7_do_reflash
Input: goodix - add upside-down quirk for Teclast X89 tablet
Input: add privacy screen toggle keycode
Input: uinput - fix returning EPOLLOUT from uinput_poll
Input: snvs_pwrkey - remove gratuitous NULL initializers
Input: snvs_pwrkey - send key events for i.MX6 S, DL and Q
Pull iomap fixes from Darrick Wong:
"Fix a race condition and a use-after-free error:
- Fix a UAF when reporting writeback errors
- Fix a race condition when handling page uptodate on fragmented file
with blocksize < pagesize"
* tag 'iomap-5.5-merge-14' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
iomap: stop using ioend after it's been freed in iomap_finish_ioend()
iomap: fix sub-page uptodate handling
Pull xfs fixes from Darrick Wong:
"Fix a couple of resource management errors and a hang:
- fix a crash in the log setup code when log mounting fails
- fix a hang when allocating space on the realtime device
- fix a block leak when freeing space on the realtime device"
* tag 'xfs-5.5-merge-17' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
xfs: fix mount failure crash on invalid iclog memory access
xfs: don't check for AG deadlock for realtime files in bunmapi
xfs: fix realtime file data space leak
Pull orangefs update from Mike Marshall:
"orangefs: posix open permission checking...
Orangefs has no open, and orangefs checks file permissions on each
file access. Posix requires that file permissions be checked on open
and nowhere else. Orangefs-through-the-kernel needs to seem posix
compliant.
The VFS opens files, even if the filesystem provides no method. We can
see if a file was successfully opened for read and or for write by
looking at file->f_mode.
When writes are flowing from the page cache, file is no longer
available. We can trust the VFS to have checked file->f_mode before
writing to the page cache.
The mode of a file might change between when it is opened and IO
commences, or it might be created with an arbitrary mode.
We'll make sure we don't hit EACCES during the IO stage by using
UID 0"
[ This is "posixish", but not a great solution in the long run, since a
proper secure network server shouldn't really trust the client like this.
But proper and secure POSIX behavior requires an open method and a
resulting cookie for IO of some kind, or similar. - Linus ]
* tag 'for-linus-5.5-ofs1' of git://git.kernel.org/pub/scm/linux/kernel/git/hubcap/linux:
orangefs: posix open permission checking...
Pull nfsd updates from Bruce Fields:
"This is a relatively quiet cycle for nfsd, mainly various bugfixes.
Possibly most interesting is Trond's fixes for some callback races
that were due to my incomplete understanding of rpc client shutdown.
Unfortunately at the last minute I've started noticing a new
intermittent failure to send callbacks. As the logic seems basically
correct, I'm leaving Trond's patches in for now, and hope to find a
fix in the next week so I don't have to revert those patches"
* tag 'nfsd-5.5' of git://linux-nfs.org/~bfields/linux: (24 commits)
nfsd: depend on CRYPTO_MD5 for legacy client tracking
NFSD fixing possible null pointer derefering in copy offload
nfsd: check for EBUSY from vfs_rmdir/vfs_unink.
nfsd: Ensure CLONE persists data and metadata changes to the target file
SUNRPC: Fix backchannel latency metrics
nfsd: restore NFSv3 ACL support
nfsd: v4 support requires CRYPTO_SHA256
nfsd: Fix cld_net->cn_tfm initialization
lockd: remove __KERNEL__ ifdefs
sunrpc: remove __KERNEL__ ifdefs
race in exportfs_decode_fh()
nfsd: Drop LIST_HEAD where the variable it declares is never used.
nfsd: document callback_wq serialization of callback code
nfsd: mark cb path down on unknown errors
nfsd: Fix races between nfsd4_cb_release() and nfsd4_shutdown_callback()
nfsd: minor 4.1 callback cleanup
SUNRPC: Fix svcauth_gss_proxy_init()
SUNRPC: Trace gssproxy upcall results
sunrpc: fix crash when cache_head become valid before update
nfsd: remove private bin2hex implementation
...
Pull NFS client updates from Trond Myklebust:
"Highlights include:
Features:
- NFSv4.2 now supports cross device offloaded copy (i.e. offloaded
copy of a file from one source server to a different target
server).
- New RDMA tracepoints for debugging congestion control and Local
Invalidate WRs.
Bugfixes and cleanups
- Drop the NFSv4.1 session slot if nfs4_delegreturn_prepare waits for
layoutreturn
- Handle bad/dead sessions correctly in nfs41_sequence_process()
- Various bugfixes to the delegation return operation.
- Various bugfixes pertaining to delegations that have been revoked.
- Cleanups to the NFS timespec code to avoid unnecessary conversions
between timespec and timespec64.
- Fix unstable RDMA connections after a reconnect
- Close race between waking an RDMA sender and posting a receive
- Wake pending RDMA tasks if connection fails
- Fix MR list corruption, and clean up MR usage
- Fix another RPCSEC_GSS issue with MIC buffer space"
* tag 'nfs-for-5.5-1' of git://git.linux-nfs.org/projects/trondmy/linux-nfs: (79 commits)
SUNRPC: Capture completion of all RPC tasks
SUNRPC: Fix another issue with MIC buffer space
NFS4: Trace lock reclaims
NFS4: Trace state recovery operation
NFSv4.2 fix memory leak in nfs42_ssc_open
NFSv4.2 fix kfree in __nfs42_copy_file_range
NFS: remove duplicated include from nfs4file.c
NFSv4: Make _nfs42_proc_copy_notify() static
NFS: Fallocate should use the nfs4_fattr_bitmap
NFS: Return -ETXTBSY when attempting to write to a swapfile
fs: nfs: sysfs: Remove NULL check before kfree
NFS: remove unneeded semicolon
NFSv4: add declaration of current_stateid
NFSv4.x: Drop the slot if nfs4_delegreturn_prepare waits for layoutreturn
NFSv4.x: Handle bad/dead sessions correctly in nfs41_sequence_process()
nfsv4: Move NFSPROC4_CLNT_COPY_NOTIFY to end of list
SUNRPC: Avoid RPC delays when exiting suspend
NFS: Add a tracepoint in nfs_fh_to_dentry()
NFSv4: Don't retry the GETATTR on old stateid in nfs4_delegreturn_done()
NFSv4: Handle NFS4ERR_OLD_STATEID in delegreturn
...
We had cases in the previous patch where we were sending the security
descriptor context on SMB3 open (file create) in cases when we hadn't
mounted with with "modefromsid" mount option.
Add check for that mount flag before calling ad_sd_context in
open init.
Signed-off-by: Steve French <stfrench@microsoft.com>
Reviewed-by: Pavel Shilovsky <pshilov@microsoft.com>
Pull more xen updates from Juergen Gross:
- a patch to fix a build warning
- a cleanup of no longer needed code in the Xen event handling
- a small series for the Xen grant driver avoiding high order
allocations and replacing an insane global limit by a per-call one
- a small series fixing Xen frontend/backend module referencing
* tag 'for-linus-5.5b-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen-blkback: allow module to be cleanly unloaded
xen/xenbus: reference count registered modules
xen/gntdev: switch from kcalloc() to kvcalloc()
xen/gntdev: replace global limit of mapped pages by limit per call
xen/gntdev: remove redundant non-zero check on ret
xen/events: remove event handling recursion detection
Merge misc Kconfig updates from Andrew Morton:
"A number of changes to Kconfig files under lib/ from Changbin Du and
Krzysztof Kozlowski"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
lib/: fix Kconfig indentation
kernel-hacking: move DEBUG_FS to 'Generic Kernel Debugging Instruments'
kernel-hacking: move DEBUG_BUGVERBOSE to 'printk and dmesg options'
kernel-hacking: create a submenu for scheduler debugging options
kernel-hacking: move SCHED_STACK_END_CHECK after DEBUG_STACK_USAGE
kernel-hacking: move Oops into 'Lockups and Hangs'
kernel-hacking: move kernel testing and coverage options to same submenu
kernel-hacking: group kernel data structures debugging together
kernel-hacking: create submenu for arch special debugging options
kernel-hacking: group sysrq/kgdb/ubsan into 'Generic Kernel Debugging Instruments'
In referenced fix we removed the RTL8168e-specific jumbo config for
RTL8168evl in rtl_hw_jumbo_enable(). We have to do the same in
rtl_hw_jumbo_disable().
v2: fix referenced commit id
Fixes: 14012c9f3b ("r8169: fix jumbo configuration for RTL8168evl")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
pipe_wait() may be simple, but since it relies on the pipe lock, it
means that we have to do the wakeup while holding the lock. That's
unfortunate, because the very first thing the waked entity will want to
do is to get the pipe lock for itself.
So get rid of the pipe_wait() usage by simply releasing the pipe lock,
doing the wakeup (if required) and then using wait_event_interruptible()
to wait on the right condition instead.
wait_event_interruptible() handles races on its own by comparing the
wakeup condition before and after adding itself to the wait queue, so
you can use an optimistic unlocked condition for it.
Cc: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
