A customer noticed RX path hang when MTU is changed on the fly while
running heavy traffic with NCSI enabled for 5717 and 5719. Since 5720
belongs to same ASIC family, we observed same issue and same fix
could solve this problem for 5720.
Signed-off-by: Siva Reddy Kallam <siva.kallam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
One of AMD based server with 5762 hangs with jumbo frame traffic.
This AMD platform has southbridge limitation which is restricting MRRS
to 4000. As a work around, driver to restricts the MRRS to 2048 for
this particular 5762 NX1 card.
Signed-off-by: Siva Reddy Kallam <siva.kallam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The enet IP only support 32 bit, it will use swiotlb buffer to do dma
mapping when xmit buffer DMA memory address is bigger than 4G in i.MX
platform. After stress suspend/resume test, it will print out:
log:
[12826.352864] fec 5b040000.ethernet: swiotlb buffer is full (sz: 191 bytes)
[12826.359676] DMA: Out of SW-IOMMU space for 191 bytes at device 5b040000.ethernet
[12826.367110] fec 5b040000.ethernet eth0: Tx DMA memory map failed
The issue is that the ready xmit buffers that are dma mapped but DMA still
don't copy them into fifo, once MAC restart, these DMA buffers are not unmapped.
So it should check the dma mapping buffer and unmap them.
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TC-based sched mode supports SRIOV enabled and SRIOV disabled. This
patch change the TM sched mode to TC-based mode in initialization
process.
Fixes: cc9bb43ab3 ("net: hns3: Add tc-based TM support for sriov enabled port")
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Burstiness of a flow is determined by the depth of a bucket, When the
upper rate of shaper is large, the current depth of a bucket is not
enough.
The default upper rate of shaper is 100G, so increase the depth of
a bucket according to UM.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for querying advertised pause frame by using
ethtool command(ethtool ethx).
Fixes: 496d03e960 ("net: hns3: Add Ethtool support to HNS3 driver")
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit c4fb2cdf575d ("net: hns3: fix a bug for phy supported feature
initialization") adds default supported features for phy, but our hardware
also supports Asym Pause. This patch adds Asym Pause support to phy
default features to prevent Asym Pause can not be advertised when the phy
negotiates flow control.
Fixes: c4fb2cdf575d ("net: hns3: fix a bug for phy supported feature initialization")
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When auto-negotiation is enabled, the MAC flow control settings is
based on the flow control negotiation result. And it should be configured
after a valid link has been established. This patch adds support to update
flow control settings after auto-negotiation has completed.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When phy exists, we use the value of phydev.autoneg to represent the
auto-negotiation state of hardware. Otherwise, we use the value of
mac.autoneg to represent it.
This patch fixes for getting a error value of auto-negotiation state in
hclge_get_autoneg().
Fixes: 46a3df9f97 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When checking whether auto-negotiation is on, driver only needs to
check the value of mac.autoneg(SW) directly, and does not need to
query it from hardware. Because this value is always synchronized
with the auto-negotiation state of hardware.
This patch removes the mac auto-negotiation state query.
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds vlan offload config commands, initializes
the rules of tx/rx vlan tag handle for hw.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a memory leak problems in change tqps process,
the function hns3_uninit_all_ring and hns3_init_all_ring
may be called many times.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Mingguang Qu <qumingguang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch modifies the return data of get_rxnfc, it will return
the current handle's rss_size but not the total tqp number.
because the tc_size has been change to the log2 of roundup
power of two of rss_size.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Mingguang Qu <qumingguang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When plugging in a USB webcam I see the following message:
xhci_hcd 0000:04:00.0: WARN Successful completion on short TX: needs
XHCI_TRUST_TX_LENGTH quirk?
handle_tx_event: 913 callbacks suppressed
All is quiet again with this patch (and I've done a fair but of soak
testing with the camera since).
Cc: <stable@vger.kernel.org>
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Trying to read from debugfs after the system has resumed from
hibernate causes a use-after-free and thus a protection fault.
Steps to reproduce:
Hibernate system, resume from hibernate, then run
$ cat /sys/kernel/debug/usb/xhci/*/command-ring/enqueue
[ 3902.765086] general protection fault: 0000 [#1] PREEMPT SMP
...
[ 3902.765136] RIP: 0010:xhci_trb_virt_to_dma.part.50+0x5/0x30
...
[ 3902.765178] Call Trace:
[ 3902.765188] xhci_ring_enqueue_show+0x1e/0x40
[ 3902.765197] seq_read+0xdb/0x3a0
[ 3902.765204] ? __handle_mm_fault+0x5fb/0x1210
[ 3902.765211] full_proxy_read+0x4a/0x70
[ 3902.765219] __vfs_read+0x23/0x120
[ 3902.765228] vfs_read+0x8e/0x130
[ 3902.765235] SyS_read+0x42/0x90
[ 3902.765242] do_syscall_64+0x6b/0x290
[ 3902.765251] entry_SYSCALL64_slow_path+0x25/0x25
The issue is caused by the xhci ring structures being reallocated
when the system is resumed, but pointers to the old structures
being retained in the debugfs files "private" field:
The proposed patch fixes this issue by storing a pointer to the xhci_ring
field in the xhci device structure in debugfs rather than directly
storing a pointer to the xhci_ring.
Fixes: 02b6fdc2a1 ("usb: xhci: Add debugfs interface for xHCI driver")
Signed-off-by: Alexander Kappner <agk@godking.net>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Free the virt_device and its debugfs_private member together.
When resuming from hibernate the .free_dev callback unconditionally
freed the debugfs_private member, but could leave virt_device intact.
This triggered a NULL pointer dereference after resume when usbmuxd
sent a USBDEVFS_SETCONFIGURATION ioctl to a device, trying to add a
endpoint debugfs entry to a already freed debugfs_private pointer.
Fixes: 02b6fdc2a1 ("usb: xhci: Add debugfs interface for xHCI driver")
Reported-by: Alexander Kappner <agk@godking.net>
Tested-by: Alexander Kappner <agk@godking.net>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Johan writes
USB-serial fixes for v4.15-rc6
Here are some new device ids for ftdi_sio, option and qcserial.
Note that the qcserial patch enables the SetControlLineState request
(used to raise DTR/RTS) for the GPS interface of all devices using the
Sierra Wireless layout. This was required for the Sierra Wireless EM7565
and has been tested using several other modems as well.
All but the final commit have been in linux-next without any reported
issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
Since the hwlock id 0 is valid for hardware spinlock core, but now id 0
is treated as one invalid value for regmap. Thus we should add one extra
flag for regmap config to indicate if a hardware spinlock should be used,
then id 0 can be valid for regmap to request.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This is a follow-up to commit a5ba91c380 ("regmap: debugfs: emit a
debug message when locking is disabled"). I figured that a user may
see this message, grep the code, come to this place and he still won't
know why we actually disabled debugfs.
Add a comment explaining the reason.
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add memory dump to the firmware crash data file which is provided to user space
via devcoredump interface. This makes it easier for firmware engineers to debug
firmware crashes.
Due to increased memory consumption the memory dump is disabled by default. To
enable it make sure that bit 3 is set in coredump_mask module parameter:
modprobe ath10k_core coredump_mask=0xffffffff
When RAMDUMP is enabled a buffer for the dump is allocated with vmalloc during
device probe. The actual memory layout is different in hardware versions and
the layouts are defined in coredump.c. The memory is split to regions and, to
get even finegrained control of what to copy, the region can split to smaller
sections as not all registers are readable (which could cause the whole system
to stall).
Signed-off-by: Alan Liu <alanliu@qca.qualcomm.com>
[kvalo@qca.qualcomm.com: refactoring and cleanup]
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
For memory dump support (it consumes quite a lot of memory) we need to control
what is exactly stored to the crash dump. Add a module parameter call
coredump_mask to do that. It's a bit mask of these values:
enum ath10k_fw_crash_dump_type {
ATH10K_FW_CRASH_DUMP_REGISTERS = 0,
ATH10K_FW_CRASH_DUMP_CE_DATA = 1,
ATH10K_FW_CRASH_DUMP_MAX,
};
For example, if we only want to store CE_DATA we would enable bit 2:
modprobe ath10k_core coredump_mask=0x2
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Now coredump is totally separate from debug.c and doesn't depend on
CONFIG_ATH10K_DEBUGFS anymore, only on CONFIG_DEV_COREDUMP. Also remove
leftovers from the removed debugfs file support.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In preparation to add RAM dump support. No functional changes, only moving code
and renaming function names.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The fw_crash_dump file was deprecated by commmit 727000e6af ("ath10k: support
dev_coredump for crash dump") in v4.11 in favor of dev_coredump interface,
remove it now for good. Everyone should use dev_coredump now.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Enable TDLS wider bandwidth support for 5GHz based on firmware wmi capabilities.
This patch is required for chipset QCA9888. Tested with firmware version
10.4-3.5.1-00018.
Signed-off-by: Balaji Pothunoori <bpothuno@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
HL1.0 firmware is not loaded via bmi. The bmi specific
code should not be executed for HL1.0
Add fw feature flag for non bmi targets and skip the bmi
specific code for non bmi targets.
Signed-off-by: Rakesh Pillai <pillair@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
WCN3990 CE descriptor uses 64bit address for
src/dst ring buffer. It has extended field for toeplitz
hash result, which is being used for HW assisted
hash results.
To accommodate WCN3990 descriptor, define new CE
descriptor for extended addressing mode and related
methods to handle the descriptor data.
Signed-off-by: Govind Singh <govinds@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
CE send and receive API's are using u32 ring address, which
truncates the address for target with 64bit addressing range.
Use dma_addr_t for ce buffers to support target with extended
addressing range.
Signed-off-by: Govind Singh <govinds@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
paddrs_ring_64 holds the physical device address of the
rx buffers that host SW provides for the MAC HW to fill.
Since this field is used in rx ring setup and rx ring
replenish in rx data path. Define separate methods
for handling 64 bit ring paddr and attach them dynamically
based on target_64bit hw param flag. Use u64 type
while popping paddr from the rx hash table for 64bit target.
Signed-off-by: Govind Singh <govinds@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
WCN3990 uses larger ring size in comparison to existing
ring size value.
Add rx ring size hw param for supporting different rx ring
size across multiple target.
Signed-off-by: Govind Singh <govinds@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
WCN3990 target uses 64 bit frags_paddr in htt tx descriptor,
which holds the physical address of SKB fragments in tx data path.
In order to support 64 bit bit frags_paddr in htt tx descriptor, define
htt_data_tx_desc_64 descriptor and ath10k_htt_tx_64 method for handling
tx data path with new descriptor fields.
Signed-off-by: Govind Singh <govinds@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
WCN3990 target uses 64 bit frag descriptor and more
fields in TSO flag.
Add support for 64 bit HTT frag descriptor.
Signed-off-by: Govind Singh <govinds@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
WCN3900 target uses 64bit rx_ring_base_paddr and
fw_idx_shadow_reg_paddr fields in HTT rx ring cfg message.
These address points to the memory region where remote
ring empty buffers are allocated.
In order to add 64 bit htt rx ring cfg, define separate
64 bit htt rx ring cfg message and attach it in runtime
based on target_64bit hw param flag.
Signed-off-by: Govind Singh <govinds@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
WCN3990 target use 64bit msdu address in htt in-order
indication message. Add support for 64 bit msdu address in
HTT_T2H_MSG_TYPE_RX_IN_ORD_PADDR_IND message.
Signed-off-by: Govind Singh <govinds@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
WCN3990 rx descriptor uses different offset of msdu start, msdu end,
ppdu end, rx pkt end and rx frag info.
To accommodate different offsets, define respective fields in
rx descriptor of WCN3990 target.
Signed-off-by: Govind Singh <govinds@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
WCN3990 target supports 37-bit addressing mode. In order
to accommodate extended address support, add hw param to
indicate if the target supports addressing above 32-bits.
Signed-off-by: Rakesh Pillai <pillair@qti.qualcomm.com>
Signed-off-by: Govind Singh <govinds@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
