The #ifdef checks are hard to get right, in this case some functions
should have been left inside a CONFIG_PM_SLEEP check as seen by this
message:
drivers/net/wireless/ath/wil6210/pcie_bus.c:489:12: error: 'wil6210_pm_resume' defined but not used [-Werror=unused-function]
drivers/net/wireless/ath/wil6210/pcie_bus.c:484:12: error: 'wil6210_pm_suspend' defined but not used [-Werror=unused-function]
Using an __maybe_unused is easier here, so I'm replacing all the
other #ifdef in this file as well for consistency.
Fixes: 94162666cd ("wil6210: run-time PM when interface down")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Variable fc is being assigned but never used, so remove it. Cleans
up the clang warning:
warning: Value stored to 'fc' is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Pull hwmon fix from Guenter Roeck:
"Handle errors from thermal subsystem"
* tag 'hwmon-for-linus-v4.15-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: Deal with errors from the thermal subsystem
Pull GPIO fixes from Linus Walleij:
"Two fixes. They are both kind of important, so why not send a pull
request on christmas eve.
- Fix a build problem in the gpio single register created by
refactorings.
- Fix assignment of GPIO line names, something that was mangled by
another patch"
* tag 'gpio-v4.15-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio: fix "gpio-line-names" property retrieval
gpio: gpio-reg: fix build
Some BIOS implementations route ACPI codes other than 0x83 to INT3400
device. Ignore these ACPI notification codes because the INT3400 driver
does not handle them.
Signed-off-by: Brian Bian <brian.bian@linux.intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
These duplicate includes have been found with scripts/checkincludes.pl but
they have been removed manually to avoid removing false positives.
Signed-off-by: Pravin Shedge <pravin.shedge4linux@gmail.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Even though the header file linux/clk-provider.h is already being properly
included in clk-mtk.h, the definition of struct clk_onecell_data still
must depend on CONFIG_COMMON_CLK defined and thus it's possible that
below build warnings occur when CONFIG_COMMON_CLK is not being selected.
Therefore, these functions which need struct clk_onecell_data without
declaring that structure first requires simply declaring that this struct
exists prior to referencing it in clk-mtk.h
Changes from v1->v2:
enhance v1 based on two useful solutions Jean Delvare kindly suggested.
All warnings (new ones prefixed by >>):
In file included from drivers/clk/mediatek/reset.c:22:0:
>>drivers/clk/mediatek/clk-mtk.h:44:19: warning: 'struct clk_onecell_data'
declared inside parameter list will not be visible outside of
this definition or declaration
int num, struct clk_onecell_data *clk_data);
^~~~~~~~~~~~~~~~
drivers/clk/mediatek/clk-mtk.h:63:19: warning: 'struct clk_onecell_data'
declared inside parameter list will not be visible outside of
this definition or declaration
int num, struct clk_onecell_data *clk_data);
^~~~~~~~~~~~~~~~
drivers/clk/mediatek/clk-mtk.h:145:10: warning: 'struct clk_onecell_data'
declared inside parameter list will not be visible outside of
this definition or declaration
struct clk_onecell_data *clk_data);
^~~~~~~~~~~~~~~~
drivers/clk/mediatek/clk-mtk.h:164:11: warning: 'struct clk_onecell_data'
declared inside parameter list will not be visible outside of
this definition or declaration
struct clk_onecell_data *clk_data);
^~~~~~~~~~~~~~~~
drivers/clk/mediatek/clk-mtk.h:190:12: warning: 'struct clk_onecell_data'
declared inside parameter list will not be visible outside of this
definition or declaration
struct clk_onecell_data *clk_data);
^~~~~~~~~~~~~~~~
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Cc: kbuild-all@01.org
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Jean Delvare <jdelvare@suse.de>
Cc: linux-clk@vger.kernel.org
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Non-functional cleanups in lan9303_csr_reg_wait():
- Change type of param 'mask' from int to u32.
- Remove param 'value' (will probably never be used)
- Reduced retries from 1000 to 25, consistent with lan9303_read_wait.
- Removed comments
Signed-off-by: Egil Hjelmeland <privat@egil-hjelmeland.no>
Changes v1 -> v2:
- Removed comments
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit fd865802c6.
This commit causes a regression on some QCA ROME chips. The USB device
reset happens in btusb_open(), hence firmware loading gets interrupted.
Furthermore, this commit stops working after commit
("a0085f2510e8976614ad8f766b209448b385492f Bluetooth: btusb: driver to
enable the usb-wakeup feature"). Reset-resume quirk only gets enabled in
btusb_suspend() when it's not a wakeup source.
If we really want to reset the USB device, we need to do it before
btusb_open(). Let's handle it in drivers/usb/core/quirks.c.
Cc: stable@vger.kernel.org
Cc: Leif Liddy <leif.linux@gmail.com>
Cc: Matthias Kaehlcke <mka@chromium.org>
Cc: Brian Norris <briannorris@chromium.org>
Cc: Daniel Drake <drake@endlessm.com>
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Tested-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This driver seeks to force the Bluetooth device on for the duration of
5 seconds when the Bluetooth device has woken the host and after a
complete packet has been received. It does that by calling:
pm_runtime_get();
pm_runtime_mark_last_busy();
pm_runtime_put_autosuspend();
The same can be achieved more succinctly with:
pm_request_resume();
That's because after runtime resuming the device, rpm_resume() invokes
pm_runtime_mark_last_busy() followed by rpm_idle(), which will cause
the device to be suspended after expiration of the autosuspend_delay.
No functional change intended.
Cc: Frédéric Danis <frederic.danis.oss@gmail.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Loading hci_bcm with CONFIG_GPIOLIB=n results in the following splat
when calling gpiod_to_irq() from bcm_get_resources():
WARNING: CPU: 0 PID: 1006 at ./include/linux/gpio/consumer.h:450 bcm_get_resources+0x50/0x80
CPU: 0 PID: 1006 Comm: kworker/u8:4 Tainted: G A 4.15.0-rc4custom+ #4
Hardware name: Apple Inc. MacBook8,1/Mac-BE0E8AC46FE800CC, BIOS MB81.88Z.0168.B00.1708080033 08/08/2017
Call Trace:
bcm_serdev_probe+0x8b/0xc0
driver_probe_device+0x202/0x310
__driver_attach+0x85/0x90
? driver_probe_device+0x310/0x310
bus_for_each_dev+0x57/0x80
async_run_entry_fn+0x2c/0xd0
process_one_work+0x1d2/0x3d0
worker_thread+0x26/0x3c0
? process_one_work+0x3d0/0x3d0
kthread+0x10c/0x130
? kthread_create_on_node+0x40/0x40
ret_from_fork+0x1f/0x30
We could call gpiod_to_irq() only if IS_ENABLED(CONFIG_GPIOLIB) but
without GPIOLIB, the driver's power saving features can't be used,
so selecting GPIOLIB seems more appropriate.
The same issue is present in hci_intel.c and hci_nokia.c, fix those up
as well.
Reported-by: Max Shavrick <mxms@me.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
If the thermal subsystem returne -EPROBE_DEFER or any other error
when hwmon calls devm_thermal_zone_of_sensor_register(), this is
silently ignored.
I ran into this with an incorrectly defined thermal zone, making
it non-existing and thus this call failed with -EPROBE_DEFER
assuming it would appear later. The sensor was still added
which is incorrect: sensors must strictly be added after the
thermal zones, so deferred probe must be respected.
Fixes: d560168b5d ("hwmon: (core) New hwmon registration API")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
In case of tx clean up, we set '-1' as budget. This means clean up until
wq is empty or till (1 << 32) pkts are cleaned. Under heavy load this
will run for long time and cause
"watchdog: BUG: soft lockup - CPU#25 stuck for 21s!" warning.
This patch sets wq clean up budget to 256.
Signed-off-by: Govindarajulu Varadarajan <gvaradar@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Under some circumstances driver will perform PHY reset in
ksz9031_read_status() to fix autoneg failure case (idle error count =
0xFF). When this happens ksz9031 will not detect link status change any
more when connecting to Netgear 1G switch (link can be recovered sometimes by
restarting netdevice "ifconfig down up"). Reproduced with TI am572x board
equipped with ksz9031 PHY while connecting to Netgear 1G switch.
Fix the issue by reconfiguring autonegotiation after PHY reset in
ksz9031_read_status().
Fixes: d2fd719bcb ("net/phy: micrel: Add workaround for bad autoneg")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove superfluous pin setup to get out of accessing invalid I/O pin
registers because the way for pin configuring tends to be different from
various SoCs and thus it should be better being managed and controlled by
the pinctrl driver which MT7622 already can support.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ensure that we mark AN as enabled at boot time, rather than leaving
it disabled. This is noticable if your SFP module is fiber, and
it supports faster speeds than 1G with 2.5G support in place.
Fixes: 9525ae8395 ("phylink: add phylink infrastructure")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When setting the ethtool settings, ensure that the validated PHY
interface mode is propagated to the current link settings, so that
2500BaseX can be selected.
Fixes: 9525ae8395 ("phylink: add phylink infrastructure")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The original purpose of the per-superblock d_anon list was to
keep disconnected dentries in the cache between consecutive
requests to the NFS server. Dentries can be disconnected if
a client holds a file open and repeatedly performs IO on it,
and if the server drops the dentry, whether due to memory
pressure, server restart, or "echo 3 > /proc/sys/vm/drop_caches".
This purpose was thwarted by commit 75a6f82a0d ("freeing unlinked
file indefinitely delayed") which caused disconnected dentries
to be freed as soon as their refcount reached zero.
This means that, when a dentry being used by nfsd gets disconnected, a
new one needs to be allocated for every request (unless requests
overlap). As the dentry has no name, no parent, and no children,
there is little of value to cache. As small memory allocations are
typically fast (from per-cpu free lists) this likely has little cost.
This means that the original purpose of s_anon is no longer relevant:
there is no longer any need to keep disconnected dentries on a list so
they appear to be hashed.
However, s_anon now has a new use. When you mount an NFS filesystem,
the dentry stored in s_root is just a placebo. The "real" root dentry
is allocated using d_obtain_root() and so it kept on the s_anon list.
I don't know the reason for this, but suspect it related to NFSv4
where a mount of "server:/some/path" require NFS to look up the root
filehandle on the server, then walk down "/some" and "/path" to get
the filehandle to mount.
Whatever the reason, NFS depends on the s_anon list and on
shrink_dcache_for_umount() pruning all dentries on this list. So we
cannot simply remove s_anon.
We could just leave the code unchanged, but apart from that being
potentially confusing, the (unfair) bit-spin-lock which protects
s_anon can become a bottle neck when lots of disconnected dentries are
being created.
So this patch renames s_anon to s_roots, and stops storing
disconnected dentries on the list. Only dentries obtained with
d_obtain_root() are now stored on this list. There are many fewer of
these (only NFS and NILFS2 use the call, and only during filesystem
mount) so contention on the bit-lock will not be a problem.
Possibly an alternate solution should be found for NFS and NILFS2, but
that would require understanding their needs first.
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
"rem * SDM_DEN" can easily overflow on the 32-bit Meson8 and Meson8b
SoCs if the "remainder" (after the division operation) is greater than
262143Hz. This is likely to happen since the input clock for the MPLLs
on Meson8 and Meson8b is "fixed_pll", which is running at a rate of
2550MHz.
One example where this was observed to be problematic was the Ethernet
clock calculation (which takes MPLL2 as input). When requesting a rate
of 125MHz there is a remainder of 2500000Hz.
The resulting MPLL2 rate before this patch was 127488329Hz.
The resulting MPLL2 rate after this patch is 124999103Hz.
Commit b609338b26 ("clk: meson: mpll: use 64bit math in
rate_from_params") already fixed a similar issue in rate_from_params.
Fixes: 007e6e5c5f ("clk: meson: mpll: add rw operation")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Pull libnvdimm fixes from Dan Williams:
"These fixes are all tagged for -stable and have received a build
success notification from the kbuild robot.
- NVDIMM namespaces, configured to enforce 1GB alignment, fail to
initialize on platforms that mis-align the start or end of the
physical address range.
- The Linux implementation of the BTT (Block Translation Table) is
incompatible with the UEFI 2.7 definition of the BTT format. The
BTT layers a software atomic sector semantic on top of an NVDIMM
namespace. Linux needs to be compatible with the UEFI definition to
enable boot support or any pre-OS access of data on a BTT enabled
namespace.
- A fix for ACPI SMART notification events, this allows a userspace
monitor to register for health events rather than poll. This has
been broken since it was initially merged as the unit test
inadvertently worked around the problem. The urgency for fixing
this during the -rc series is driven by how expensive it is to poll
for this data (System Management Mode entry)"
* 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
libnvdimm, btt: Fix an incompatibility in the log layout
libnvdimm, btt: add a couple of missing kernel-doc lines
libnvdimm, dax: fix 1GB-aligned namespaces vs physical misalignment
libnvdimm, pfn: fix start_pad handling for aligned namespaces
acpi, nfit: fix health event notification
At least on the Chuwi Vi8 (non pro/plus) the LCD panel will show an image
shifted aprox. 20% to the left (with wraparound) and sometimes also wrong
colors, showing that the panel controller is starting with sampling the
datastream somewhere mid-line. This happens after the first blanking and
re-init of the panel.
After looking at drm.debug output I noticed that initially we inherit the
cdclk of 333333 KHz set by the GOP, but after the re-init we picked 266667
KHz, which turns out to be the cause of this problem, a quick hack to hard
code the cdclk to 333333 KHz makes the problem go away.
I've tested this on various Bay Trail devices, to make sure this not does
cause regressions on other devices and the higher cdclk does not cause
any problems on the following devices:
-GP-electronic T701 1024x600 333333 KHz cdclk after this patch
-PEAQ C1010 1920x1200 333333 KHz cdclk after this patch
-PoV mobii-wintab-800w 800x1280 333333 KHz cdclk after this patch
-Asus Transformer-T100TA 1368x768 320000 KHz cdclk after this patch
Also interesting wrt this is the comment in vlv_calc_cdclk about the
existing workaround to avoid 200 Mhz as clock because that causes issues
in some cases.
This commit extends the "do not use 200 Mhz" workaround with an extra
check to require atleast 320000 KHz (avoiding 266667 KHz) when a DSI
panel is active.
Changes in v2:
-Change the commit message and the code comment to not treat the GOP as
a reference, the GOP should not be treated as a reference
Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171220105017.11259-1-hdegoede@redhat.com
meson_mx_efuse_read calculates the address internal to the eFuse based
on the offset and the word size. This works fine with any given offset.
However, the offset is also included when writing to the output buffer.
This means that reading 4 bytes at offset 500 tries to write beyond the
array allocated by the nvmem core as it wants to write the 4 bytes to
"buffer address + offset (500)".
This issue did not show up in the previous tests since no driver uses
any value from the eFuse yet and reading the eFuse via sysfs simply
reads the whole eFuse, starting at offset 0.
Fix this by only including the offset in the internal address
calculation.
Fixes: 8caef1fa91 ("nvmem: add a driver for the Amlogic Meson6/Meson8/Meson8b SoCs")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Display WA #1183 was recently added to workaround
"Failures when enabling DPLL0 with eDP link rate 2.16
or 4.32 GHz and CD clock frequency 308.57 or 617.14 MHz
(CDCLK_CTL CD Frequency Select 10b or 11b) used in this
enabling or in previous enabling."
This workaround was designed to minimize the impact only
to save the bad case with that link rates. But HW engineers
indicated that it should be safe to apply broadly, although
they were expecting the DPLL0 link rate to be unchanged on
runtime.
We need to cover 2 cases: when we are in fact enabling DPLL0
and when we are just changing the frequency with small
differences.
This is based on previous patch by Rodrigo Vivi with suggestions
from Ville Syrjälä.
Cc: Arthur J Runyan <arthur.j.runyan@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171204232210.4958-1-lucas.demarchi@intel.com
Change the slid arg to ingress_pkey_table_fail() to a full
32Bits and do not convert to 16Bits in caller. This is so we
can keep everything 32bit in the kernel and only change to
16bit at the uapi boundary.
Signed-off-by: Don Hiatt <don.hiatt@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
The accepting QP ORD value should be adjusted not to
exceed the peer QP IRD value (RFC 6581). This is
skipped for loopback. After the ORD is validated
by i40iw_record_ird_ord(), adjust the ORD value of
the loopback accepting QP to prevent overrunning the
IRD space of the peer QP. Also move the ORD accounting
for 0-byte RDMA read to i40iw_record_ird_ord().
Fixes: f27b4746f3 ("i40iw: add connection management code")
Signed-off-by: Tatyana Nikolova <tatyana.e.nikolova@intel.com>
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Casting to u16 before validating IRD/ORD connection
parameters could cause recording wrong IRD/ORD values
in the cm_node. Validate the IRD/ORD parameters as
they are passed by the application before recording
them.
Fixes: f27b4746f3 ("i40iw: add connection management code")
Signed-off-by: Tatyana Nikolova <tatyana.e.nikolova@intel.com>
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
The LLP_DOUBT_REACHABILITY Asynchronous Event (AE) is an early
warning of a connection issue. It is followed by LLP_TOO_MANY_RETRIES
AE, if the retransmit threshold is reached and recovery is not possible
for the connection.
Currently we terminate the connection on receiving the
LLP_DOUBT_REACHABILITY AE. Ignore this AE and
terminate the connection only on LLP_TOO_MANY_RETRIES AE.
This improves the user experience on cable disconnect/reconnect
scenario while running iWARP traffic. On cable disconnect,
the QP traffic is paused and the user has a larger and more
reasonable timeout within which if the cable is reconnected,
traffic can continue.
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Partial FPDU processing is broken as the sequence number
for the first partial FPDU is wrong due to incorrect
Q2 buffer offset. The offset should be 64 rather than 16.
Fixes: 786c6adb3a ("i40iw: add puda code")
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
On IP address change event, all connected QPs are torn down
irrespective of whether IP address is involved in a connection.
Only teardown connections those source or destination address
matches the netdev interface IP address being changed, and if
they are on the same VLAN as the netdev.
Fixes: e5e74b61b1 ("i40iw: Add IP addr handling on netdev events")
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Register a netdevice notifier for netdev UP/DOWN
notification events and report the appropriate ib event.
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Lower Inbound RDMA Read Queue (Q1) object count by a factor of 2
as it is incorrectly doubled. Also, round up Q1 and Transmit FIFO (XF)
object count to power of 2 to satisfy hardware requirement.
Fixes: 86dbcd0f12 ("i40iw: add file to handle cqp calls")
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Consolidate all power of 2 round calculations to
use kernel utility function roundup_pow_of_two().
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Increase I40IW_MAX_IRD_SIZE to 64 which is the device limit.
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
SA queries SM for class port info when there is a LID_CHANGE event.
When a base lid is configured before fm is started ie when smlid is
not yet assigned, SA handles the LID_CHANGE event and tries query SM
with lid 0. This will cause an hang.
[ 1106.958820] INFO: task kworker/2:0:23 blocked for more than 120 seconds.
[ 1106.965082] Tainted: G O 4.12.0+ #1
[ 1106.969602] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables
this message.
[ 1106.977227] kworker/2:0 D 0 23 2 0x00000000
[ 1106.977250] Workqueue: infiniband update_ib_cpi [ib_core]
[ 1106.977261] Call Trace:
[ 1106.977273] __schedule+0x28e/0x860
[ 1106.977285] schedule+0x36/0x80
[ 1106.977298] schedule_timeout+0x1a3/0x2e0
[ 1106.977310] ? radix_tree_iter_tag_clear+0x1b/0x20
[ 1106.977322] ? idr_alloc+0x64/0x90
[ 1106.977334] wait_for_completion+0xe3/0x140
[ 1106.977347] ? wake_up_q+0x80/0x80
[ 1106.977369] update_ib_cpi+0x163/0x210 [ib_core]
[ 1106.977381] process_one_work+0x147/0x370
[ 1106.977394] worker_thread+0x4a/0x390
[ 1106.977406] kthread+0x109/0x140
[ 1106.977418] ? process_one_work+0x370/0x370
[ 1106.977430] ? kthread_park+0x60/0x60
[ 1106.977443] ret_from_fork+0x22/0x30
Always ensure a proper smlid is assigned before querying SM for cpi.
Fixes: ee1c60b1bf ("IB/SA: Modify SA to implicitly cache Class Port info")
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Venkata Sandeep Dhanalakota <venkata.s.dhanalakota@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
The accelerated flag only utilizes two values: 0 and 1.
Modify accelerated flag in struct nes_cm_node to bool.
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Reviewed-by: Yuval Shaia <yuval.shaia@oracle.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Pull xen fixes from Juergen Gross:
"This contains two fixes for running under Xen:
- a fix avoiding resource conflicts between adding mmio areas and
memory hotplug
- a fix setting NX bits in page table entries copied from Xen when
running a PV guest"
* tag 'for-linus-4.15-rc5-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen/balloon: Mark unallocated host memory as UNUSABLE
x86-64/Xen: eliminate W+X mappings
Pull pin control fix from Linus Walleij:
"A single pin control fix for Intel machines, affecting a bunch of
Chromebooks. Nothing else collected up amazingly"
* tag 'pinctrl-v4.15-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: cherryview: Mask all interrupts on Intel_Strago based systems
Pull drm fixes from Dave Airlie:
"I've got most of two weeks worth of fixes here due to being on
holidays last week.
The main things are:
- Core:
* Syncobj fd reference count fix
* Leasing ioctl misuse fix
- nouveau regression fixes
- further amdgpu DC fixes
- sun4i regression fixes
I'm not sure I'll see many fixes over next couple of weeks, we'll see
how we go"
* tag 'drm-fixes-for-v4.15-rc5' of git://people.freedesktop.org/~airlied/linux: (27 commits)
drm/syncobj: Stop reusing the same struct file for all syncobj -> fd
drm: move lease init after validation in drm_lease_create
drm/plane: Make framebuffer refcounting the responsibility of setplane_internal callers
drm/sun4i: hdmi: Move the mode_valid callback to the encoder
drm/nouveau: fix obvious memory leak
drm/i915: Protect DDI port to DPLL map from theoretical race.
drm/i915/lpe: Remove double-encapsulation of info string
drm/sun4i: Fix error path handling
drm/nouveau: use alternate memory type for system-memory buffers with kind != 0
drm/nouveau: avoid GPU page sizes > PAGE_SIZE for buffer objects in host memory
drm/nouveau/mmu/gp10b: use correct implementation
drm/nouveau/pci: do a msi rearm on init
drm/nouveau/imem/nv50: fix refcount_t warning
drm/nouveau/bios/dp: support DP Info Table 2.0
drm/nouveau/fbcon: fix NULL pointer access in nouveau_fbcon_destroy
drm/amd/display: Fix rehook MST display not light back on
drm/amd/display: fix missing pixel clock adjustment for dongle
drm/amd/display: set chroma taps to 1 when not scaling
drm/amd/display: add pipe locking before front end programing
drm/sun4i: validate modes for HDMI
...
Pull clk fixes from Stephen Boyd:
"Here's a trio of fixes:
- The runtime PM clk patches that landed this merge window forgot to
runtime resume devices that may be off while recalculating and
setting rates of child clks of whatever clk is changing rates.
- We had a NULL pointer deref in an old clk tracepoint when
clk_set_parent() is called with a NULL parent pointer. This
shouldn't really happen, but it's best to avoid this regardless.
- The sun9i-mmc clk driver didn't provide 'reset' support, just
'assert' and 'deassert' so the MMC driver stopped probing when the
probe was changed to do a reset instead of assert/deassert pair.
This implements the reset so things work again"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: sunxi: sun9i-mmc: Implement reset callback for reset controls
clk: fix a panic error caused by accessing NULL pointer
clk: Manage proper runtime PM state in clk_change_rate()
Looking at a CI failure with an ominous line of
[ 362.550715] hangcheck current seqno ffffff6b, last ffffff8c, hangcheck ffffff6b [6016 ms], inflight 118
with no apparent cause for the seqno to be negative, left me wondering
if someone had scribbled over the HWSP. So include the HWSP in the
engine dump to see if there are more signs of random scribbling.
v2: Fix row pointer, i is now incremented by 8 so doesn't need scaling
by 8, and we don't need to keep volatile here as the status_page isn't
marked up as volatile itself.
v3: Use hexdump, with suppression of identical lines. (Tvrtko)
Which results in
HWSP:
00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
*
00000040 00000001 00000000 00000018 00000002 00000001 00000000 00000018 00000000
00000060 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000003
00000080 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
*
000000c0 00000002 00000000 00000000 00000000 00000000 00000000 00000000 00000000
000000e0 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
*
instead of 128 lines of mostly 0s.
v4: Tidy up the locals
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171222182521.18106-1-chris@chris-wilson.co.uk
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
