commit 54e181e073 upstream.
Since the beginning of the parisc-linux port, sometimes 64bit SMP kernels were
not able to bring up other CPUs than the monarch CPU and instead crashed the
kernel. The reason was unclear, esp. since it involved various machines (e.g.
J5600, J6750 and SuperDome). Testing showed, that those crashes didn't happened
when less than 4GB were installed, or if a 32bit Linux kernel was booted.
In the end, the fix for those SMP problems is trivial:
During the early phase of the initialization of the CPUs, including the monarch
CPU, the PDC_PSW firmware function to enable WIDE (=64bit) mode is called.
It's documented that this firmware function may clobber various registers, and
one one of those possibly clobbered registers is %cr30 which holds the task
thread info pointer.
Now, if %cr30 would always have been clobbered, then this bug would have been
detected much earlier. But lots of testing finally showed, that - at least for
%cr30 - on some machines only the upper 32bits of the 64bit register suddenly
turned zero after the firmware call.
So, after finding the root cause, the explanation for the various crashes
became clear:
- On 32bit SMP Linux kernels all upper 32bit were zero, so we didn't faced this
problem.
- Monarch CPUs in 64bit mode always booted sucessfully, because the inital task
thread info pointer was below 4GB.
- Secondary CPUs booted sucessfully on machines with less than 4GB RAM because
the upper 32bit were zero anyay.
- Secondary CPus failed to boot if we had more than 4GB RAM and the task thread
info pointer was located above the 4GB boundary.
Finally, the patch to fix this problem is trivial by saving the %cr30 register
before the firmware call and restoring it afterwards.
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 97b9410643 upstream.
Marc Kleine-Budde pointed out, that commit 77cc982 "clocksource: use
clockevents_config_and_register() where possible" caused a regression
for some of the converted subarchs.
The reason is, that the clockevents core code converts the minimal
hardware tick delta to a nanosecond value for core internal
usage. This conversion is affected by integer math rounding loss, so
the backwards conversion to hardware ticks will likely result in a
value which is less than the configured hardware limitation. The
affected subarchs used their own workaround (SIGH!) which got lost in
the conversion.
The solution for the issue at hand is simple: adding evt->mult - 1 to
the shifted value before the integer divison in the core conversion
function takes care of it. But this only works for the case where for
the scaled math mult/shift pair "mult <= 1 << shift" is true. For the
case where "mult > 1 << shift" we can apply the rounding add only for
the minimum delta value to make sure that the backward conversion is
not less than the given hardware limit. For the upper bound we need to
omit the rounding add, because the backwards conversion is always
larger than the original latch value. That would violate the upper
bound of the hardware device.
Though looking closer at the details of that function reveals another
bogosity: The upper bounds check is broken as well. Checking for a
resulting "clc" value greater than KTIME_MAX after the conversion is
pointless. The conversion does:
u64 clc = (latch << evt->shift) / evt->mult;
So there is no sanity check for (latch << evt->shift) exceeding the
64bit boundary. The latch argument is "unsigned long", so on a 64bit
arch the handed in argument could easily lead to an unnoticed shift
overflow. With the above rounding fix applied the calculation before
the divison is:
u64 clc = (latch << evt->shift) + evt->mult - 1;
So we need to make sure, that neither the shift nor the rounding add
is overflowing the u64 boundary.
[ukl: move assignment to rnd after eventually changing mult, fix build
issue and correct comment with the right math]
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Russell King - ARM Linux <linux@arm.linux.org.uk>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: nicolas.ferre@atmel.com
Cc: Marc Pignat <marc.pignat@hevs.ch>
Cc: john.stultz@linaro.org
Cc: kernel@pengutronix.de
Cc: Ronald Wahl <ronald.wahl@raritan.com>
Cc: LAK <linux-arm-kernel@lists.infradead.org>
Cc: Ludovic Desroches <ludovic.desroches@atmel.com>
Link: http://lkml.kernel.org/r/1380052223-24139-1-git-send-email-u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 60a01f558a upstream.
This patch addresses a long-standing bug where the get_user_pages_fast()
write parameter used for setting the underlying page table entry permission
bits was incorrectly set to write=1 for data_direction=DMA_TO_DEVICE, and
passed into get_user_pages_fast() via vhost_scsi_map_iov_to_sgl().
However, this parameter is intended to signal WRITEs to pinned userspace
PTEs for the virtio-scsi DMA_FROM_DEVICE -> READ payload case, and *not*
for the virtio-scsi DMA_TO_DEVICE -> WRITE payload case.
This bug would manifest itself as random process segmentation faults on
KVM host after repeated vhost starts + stops and/or with lots of vhost
endpoints + LUNs.
Cc: Stefan Hajnoczi <stefanha@redhat.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Asias He <asias@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 58932e96e4 upstream.
In case of error, the function scsi_host_lookup() returns NULL
pointer not ERR_PTR(). The IS_ERR() test in the return value check
should be replaced with NULL test.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 61e4947c99 upstream.
Since:
commit 7ceb17e87b
md: Allow devices to be re-added to a read-only array.
spares are activated on a read-only array. In case of raid1 and raid10
personalities it causes that not-in-sync devices are marked in-sync
without checking if recovery has been finished.
If a read-only array is degraded and one of its devices is not in-sync
(because the array has been only partially recovered) recovery will be skipped.
This patch adds checking if recovery has been finished before marking a device
in-sync for raid1 and raid10 personalities. In case of raid5 personality
such condition is already present (at raid5.c:6029).
Bug was introduced in 3.10 and causes data corruption.
Signed-off-by: Pawel Baldysiak <pawel.baldysiak@intel.com>
Signed-off-by: Lukasz Dorau <lukasz.dorau@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f13e220161 upstream.
libata EH decrements scmd->retries when the command failed for reasons
unrelated to the command itself so that, for example, commands aborted
due to suspend / resume cycle don't get penalized; however,
decrementing scmd->retries isn't enough for ATA passthrough commands.
Without this fix, ATA passthrough commands are not resend to the
drive, and no error is signalled to the caller because:
- allowed retry count is 1
- ata_eh_qc_complete fill the sense data, so result is valid
- sense data is filled with untouched ATA registers.
Signed-off-by: Gwendal Grignou <gwendal@google.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d47648fcf0 upstream.
SCSI discard will damage discard stripe bio setting, eg, some fields are
changed. If the stripe is reused very soon, we have wrong bios setting. We
remove discard stripe from hash list, so next time the strip will be fully
initialized.
Suitable for backport to 3.7+.
Signed-off-by: Shaohua Li <shli@fusionio.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 37c61ff31e upstream.
SCSI layer will add new payload for discard request. If two bios are merged
to one, the second bio has bi_vcnt 1 which is set in raid5. This will confuse
SCSI and cause oops.
Suitable for backport to 3.7+
Reported-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Shaohua Li <shli@fusionio.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 10c580e423 upstream.
Sujit has found a race condition that would make q->nr_pending
unbalanced, it occurs as Sujit explained:
"
sd_probe_async() ->
add_disk() ->
disk_add_event() ->
schedule(disk_events_workfn)
sd_revalidate_disk()
blk_pm_runtime_init()
return;
Let's say the disk_events_workfn() calls sd_check_events() which tries
to send test_unit_ready() and because of sd_revalidate_disk() trying to
send another commands the test_unit_ready() might be re-queued as the
tagged command queuing is disabled.
So the race condition is -
Thread 1 | Thread 2
sd_revalidate_disk() | sd_check_events()
...nr_pending = 0 as q->dev = NULL| scsi_queue_insert()
blk_runtime_pm_init() | blk_pm_requeue_request() ->
| nr_pending = -1 since
| q->dev != NULL
"
The problem is, the test_unit_ready request doesn't get counted the
first time it is queued, so the later decrement of q->nr_pending in
blk_pm_requeue_request makes it unbalanced.
Fix this by calling blk_pm_runtime_init before add_disk so that all
requests initiated there will all be counted.
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Reported-and-tested-by: Sujit Reddy Thumma <sthumma@codeaurora.org>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d5a7b406c5 upstream.
In patch
0d1862e can: flexcan: fix flexcan_chip_start() on imx6
the loop in flexcan_chip_start() that iterates over all mailboxes after the
soft reset of the CAN core was removed. This loop put all mailboxes (even the
ones marked as reserved 1...7) into EMPTY/INACTIVE mode. On mailboxes 8...63,
this aborts any pending TX messages.
After a cold boot there is random garbage in the mailboxes, which leads to
spontaneous transmit of CAN frames during first activation. Further if the
interface was disabled with a pending message (usually due to an error
condition on the CAN bus), this message is retransmitted after enabling the
interface again.
This patch fixes the regression by:
1) Limiting the maximum number of used mailboxes to 8, 0...7 are used by the RX
FIFO, 8 is used by TX.
2) Marking the TX mailbox as EMPTY/INACTIVE, so that any pending TX of that
mailbox is aborted.
Cc: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e358784297 upstream.
The current implemetation of of_match_device() relies that the of_device_id
table in the driver is sorted from most specific to least specific compatible.
Without this patch the mx28 is detected as the less specific p1010. This leads
to a p1010 specific workaround is activated on the mx28, which is not needed.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5abbeea553 upstream.
In commit:
3078cde7 can: at91_can: add dt support
device tree support was added to the at91_can driver. In this commit the
mapping of device to driver data was mixed up. This results in the sam9x5
parameters being used for the sam9263 and the workaround for the broken mailbox
0 on the sam9263 not being activated.
This patch fixes the broken platform_device_id table.
Cc: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9473ca6e92 upstream.
An error in calculating the offset in an skb causes the driver to read
essential device info from the wrong locations. The main effect is that
automatic gain calculations are nonsense.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 453b0c3f69 upstream.
601216e "mwifiex: process RX packets in SDIO IRQ thread directly"
introduced a command timeout issue which can be reproduced easily on
an AM33xx platform using a test application written by Daniel Mack:
https://gist.github.com/zonque/6579314
mwifiex_main_process() is called from both the SDIO handler and
the workqueue. In case an interrupt occurs right after the
int_status check, but before updating the mwifiex_processing flag,
this interrupt gets lost, resulting in a command timeout and
consequently a card reset.
Let main_proc_lock protect both int_status and mwifiex_processing
flag. This fixes the interrupt lost issue.
Reported-by: Sven Neumann <s.neumann@raumfeld.com>
Reported-by: Andreas Fenkart <andreas.fenkart@streamunlimited.com>
Tested-by: Daniel Mack <zonque@gmail.com>
Reviewed-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Paul Stewart <pstew@chromium.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f478f33a93 upstream.
Fix kernel warning when using WEXT for configuring ad-hoc mode,
e.g. "iwconfig wlan0 essid test channel 1"
WARNING: at net/wireless/chan.c:373 cfg80211_chandef_usable+0x50/0x21c [cfg80211]()
The warning is caused by an uninitialized variable center_freq1.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ec30326ea7 upstream.
Otherwise, if queues are full during a scan, tx scheduling does not
resume after switching back to the home channel.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d86aa4f8ca upstream.
If a frame's timestamp is calculated, and the bitrate
calculation goes wrong and returns zero, the system
will attempt to divide by zero and crash. Catch this
case and print the rate information that the driver
reported when this happens.
Reported-by: Thomas Lindroth <thomas.lindroth@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0c5b93290b upstream.
When clients are idle for too long, hostapd sends nullfunc frames for
probing. When those are acked by the client, the idle time needs to be
updated.
To make this work (and to avoid unnecessary probing), update sta->last_rx
whenever an ACK was received for a tx packet. Only do this if the flag
IEEE80211_HW_REPORTS_TX_ACK_STATUS is set.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6329b8d917 upstream.
If an Ad-Hoc node receives packets with the Cell ID or its own MAC
address as source address, it hits a WARN_ON in sta_info_insert_check()
With many packets, this can massively spam the logs. One way that this
can easily happen is through having Cisco APs in the area with rouge AP
detection and countermeasures enabled.
Such Cisco APs will regularly send fake beacons, disassoc and deauth
packets that trigger these warnings.
To fix this issue, drop such spoofed packets early in the rx path.
Reported-by: Thomas Huehn <thomas@net.t-labs.tu-berlin.de>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a754055a12 upstream.
__ieee80211_scan_completed is called from a worker. This
means that the following flow is possible.
* driver calls ieee80211_scan_completed
* mac80211 cancels the scan (that is already complete)
* __ieee80211_scan_completed runs
When scan_work will finally run, it will see that the scan
hasn't been aborted and might even trigger another scan on
another band. This leads to a situation where cfg80211's
scan is not done and no further scan can be issued.
Fix this by setting a new flag when a HW scan is being
cancelled so that no other scan will be triggered.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ea84753c98 upstream.
Both Anjana and Eunki reported a stall in the while_each_thread loop
in cgroup_attach_task().
It's because, when we attach a single thread to a cgroup, if the cgroup
is exiting or is already in that cgroup, we won't break the loop.
If the task is already in the cgroup, the bug can lead to another thread
being attached to the cgroup unexpectedly:
# echo 5207 > tasks
# cat tasks
5207
# echo 5207 > tasks
# cat tasks
5207
5215
What's worse, if the task to be attached isn't the leader of the thread
group, we might never exit the loop, hence cpu stall. Thanks for Oleg's
analysis.
This bug was introduced by commit 081aa458c3
("cgroup: consolidate cgroup_attach_task() and cgroup_attach_proc()")
[ lizf: - fixed the first continue, pointed out by Oleg,
- rewrote changelog. ]
Reported-by: Eunki Kim <eunki_kim@samsung.com>
Reported-by: Anjana V Kumar <anjanavk12@gmail.com>
Signed-off-by: Anjana V Kumar <anjanavk12@gmail.com>
Signed-off-by: Li Zefan <lizefan@huawei.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d544db293a upstream.
Add new supporting declarations to option.c, to support Huawei new
devices with new bInterfaceSubClass value.
Signed-off-by: fangxiaozhi <huananhu@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 32c37fc30c upstream.
Some USB drive enclosures do not correctly report an
overflow condition if they hold a drive with a capacity
over 2TB and are confronted with a READ_CAPACITY_10.
They answer with their capacity modulo 2TB.
The generic layer cannot cope with that. It must be told
to use READ_CAPACITY_16 from the beginning.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c9d09dc7ad upstream.
Without this change, the USB cable for Freestyle Option and compatible
glucometers will not be detected by the driver.
Signed-off-by: Diego Elio Pettenò <flameeyes@flameeyes.eu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d969de8d83 upstream.
Due to missing braces on an if statement, in presence of a device_node a
port was always assigned -1, regardless of any alias entries in the
device tree. Conversely, if device_node was NULL, an unitialized port
ended up being used.
This patch adds the missing braces, fixing the issues.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Tony Prisk <linux@prisktech.co.nz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f5563318ff upstream.
When parsing an invalid radiotap header, the parser can overrun
the buffer that is passed in because it doesn't correctly check
1) the minimum radiotap header size
2) the space for extended bitmaps
The first issue doesn't affect any in-kernel user as they all
check the minimum size before calling the radiotap function.
The second issue could potentially affect the kernel if an skb
is passed in that consists only of the radiotap header with a
lot of extended bitmaps that extend past the SKB. In that case
a read-only buffer overrun by at most 4 bytes is possible.
Fix this by adding the appropriate checks to the parser.
Reported-by: Evan Huus <eapache@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e3b6c655b9 upstream.
Toralf runs trinity on UML/i386. After some time it hangs and the last
message line is
BUG: soft lockup - CPU#0 stuck for 22s! [trinity-child0:1521]
It's found that pages_dirtied becomes very large. More than 1000000000
pages in this case:
period = HZ * pages_dirtied / task_ratelimit;
BUG_ON(pages_dirtied > 2000000000);
BUG_ON(pages_dirtied > 1000000000); <---------
UML debug printf shows that we got negative pause here:
ick: pause : -984
ick: pages_dirtied : 0
ick: task_ratelimit: 0
pause:
+ if (pause < 0) {
+ extern int printf(char *, ...);
+ printf("ick : pause : %li\n", pause);
+ printf("ick: pages_dirtied : %lu\n", pages_dirtied);
+ printf("ick: task_ratelimit: %lu\n", task_ratelimit);
+ BUG_ON(1);
+ }
trace_balance_dirty_pages(bdi,
Since pause is bounded by [min_pause, max_pause] where min_pause is also
bounded by max_pause. It's suspected and demonstrated that the
max_pause calculation goes wrong:
ick: pause : -717
ick: min_pause : -177
ick: max_pause : -717
ick: pages_dirtied : 14
ick: task_ratelimit: 0
The problem lies in the two "long = unsigned long" assignments in
bdi_max_pause() which might go negative if the highest bit is 1, and the
min_t(long, ...) check failed to protect it falling under 0. Fix all of
them by using "unsigned long" throughout the function.
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Reported-by: Toralf Förster <toralf.foerster@gmx.de>
Tested-by: Toralf Förster <toralf.foerster@gmx.de>
Reviewed-by: Jan Kara <jack@suse.cz>
Cc: Richard Weinberger <richard@nod.at>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ccb041571b upstream.
The create_bind_cap_vol_ctl does not create any control indicating
that an inverted dmic is present. Therefore, create multiple
capture volumes in this scenario, so we always have some indication
that the internal mic is inverted.
This happens on the Lenovo Ideapad U310 as well as the Lenovo Yoga 13
(both are based on the CX20590 codec), but the fix is generic and
could be needed for other codecs/machines too.
Thanks to Szymon Acedański for the pointer and a draft patch.
BugLink: https://bugs.launchpad.net/bugs/1239392
BugLink: https://bugs.launchpad.net/bugs/1227491
Reported-by: Szymon Acedański <accek@mimuw.edu.pl>
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ac536a848a upstream.
The pcm_usb_stream plugin requires the mremap explicitly for the read
buffer, as it expands itself once after reading the required size.
But the commit [314e51b9: mm: kill vma flag VM_RESERVED and
mm->reserved_vm counter] converted blindly to a combination of
VM_DONTEXPAND | VM_DONTDUMP like other normal drivers, and this
resulted in the failure of mremap().
For fixing this regression, we need to remove VM_DONTEXPAND for the
read-buffer mmap.
Reported-and-tested-by: James Miller <jamesstewartmiller@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 750e8165f5 upstream.
Occasionally we hit the BUG_ON(pmd_trans_huge(*pmd)) at the end of
__split_huge_page_pmd(): seen when doing madvise(,,MADV_DONTNEED).
It's invalid: we don't always have down_write of mmap_sem there: a racing
do_huge_pmd_wp_page() might have copied-on-write to another huge page
before our split_huge_page() got the anon_vma lock.
Forget the BUG_ON, just go back and try again if this happens.
Signed-off-by: Hugh Dickins <hughd@google.com>
Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: David Rientjes <rientjes@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e9c6a18264 upstream.
This patch fixes a particular type of data corruption that has been
encountered when loading a snapshot's metadata from disk.
When we allocate a new chunk in persistent_prepare, we increment
ps->next_free and we make sure that it doesn't point to a metadata area
by further incrementing it if necessary.
When we load metadata from disk on device activation, ps->next_free is
positioned after the last used data chunk. However, if this last used
data chunk is followed by a metadata area, ps->next_free is positioned
erroneously to the metadata area. A newly-allocated chunk is placed at
the same location as the metadata area, resulting in data or metadata
corruption.
This patch changes the code so that ps->next_free skips the metadata
area when metadata are loaded in function read_exceptions.
The patch also moves a piece of code from persistent_prepare_exception
to a separate function skip_metadata to avoid code duplication.
CVE-2013-4299
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 03d152d558 upstream.
Checking LP_INT_STAT is not enough in the interrupt handler because its
contents get updated regardless of whether the pin has interrupt enabled or
not. This causes the driver to loop forever for GPIOs that are pulled up.
Fix this by checking the interrupt enable bit for the pin as well.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 29114fd7db upstream.
This fixes a long-standing Integrator/CP regression from
commit 870e2928cf
"ARM: integrator-cp: convert use CLKSRC_OF for timer init"
When this code was introduced, the both aliases pointing the
system to use timer1 as primary (clocksource) and timer2
as secondary (clockevent) was ignored, and the system would
simply use the first two timers found as clocksource and
clockevent.
However this made the system timeline accelerate by a
factor x25, as it turns out that the way the clocking
actually works (totally undocumented and found after some
trial-and-error) is that timer0 runs @ 25MHz and timer1
and timer2 runs @ 1MHz. Presumably this divider setting
is a boot-on default and configurable albeit the way to
configure it is not documented.
So as a quick fix to the problem, let's mark timer0 as
disabled, so the code will chose timer1 and timer2 as it
used to.
This also deletes the two aliases for the primary and
secondary timer as they have been superceded by the
auto-selection
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3c1532df5c upstream.
In ftrace_syscall_enter(),
syscall_get_arguments(..., 0, n, ...)
if (i == 0) { <handle ORIG_r0> ...; n--;}
memcpy(..., n * sizeof(args[0]));
If 'number of arguments(n)' is zero and 'argument index(i)' is also zero in
syscall_get_arguments(), none of arguments should be copied by memcpy().
Otherwise 'n--' can be a big positive number and unexpected amount of data
will be copied. Tracing system calls which take no argument, say sync(void),
may hit this case and eventually make the system corrupted.
This patch fixes the issue both in syscall_get_arguments() and
syscall_set_arguments().
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d69e0f7ea9 ]
When IFF_ALLMULTI flag is set on interface and IFF_PROMISC isn't,
emac_dev_mcast_set should only enable RX of multicasts and reset
MACHASH registers.
It does this, but afterwards it either sets up multicast MACs
filtering or disables RX of multicasts and resets MACHASH registers
again, rendering IFF_ALLMULTI flag useless.
This patch fixes emac_dev_mcast_set, so that multicast MACs filtering and
disabling of RX of multicasts are skipped when IFF_ALLMULTI flag is set.
Tested with kernel 2.6.37.
Signed-off-by: Mariusz Ceier <mceier+kernel@gmail.com>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
