commit 04f5866e41 upstream.
The core dumping code has always run without holding the mmap_sem for
writing, despite that is the only way to ensure that the entire vma
layout will not change from under it. Only using some signal
serialization on the processes belonging to the mm is not nearly enough.
This was pointed out earlier. For example in Hugh's post from Jul 2017:
https://lkml.kernel.org/r/alpine.LSU.2.11.1707191716030.2055@eggly.anvils
"Not strictly relevant here, but a related note: I was very surprised
to discover, only quite recently, how handle_mm_fault() may be called
without down_read(mmap_sem) - when core dumping. That seems a
misguided optimization to me, which would also be nice to correct"
In particular because the growsdown and growsup can move the
vm_start/vm_end the various loops the core dump does around the vma will
not be consistent if page faults can happen concurrently.
Pretty much all users calling mmget_not_zero()/get_task_mm() and then
taking the mmap_sem had the potential to introduce unexpected side
effects in the core dumping code.
Adding mmap_sem for writing around the ->core_dump invocation is a
viable long term fix, but it requires removing all copy user and page
faults and to replace them with get_dump_page() for all binary formats
which is not suitable as a short term fix.
For the time being this solution manually covers the places that can
confuse the core dump either by altering the vma layout or the vma flags
while it runs. Once ->core_dump runs under mmap_sem for writing the
function mmget_still_valid() can be dropped.
Allowing mmap_sem protected sections to run in parallel with the
coredump provides some minor parallelism advantage to the swapoff code
(which seems to be safe enough by never mangling any vma field and can
keep doing swapins in parallel to the core dumping) and to some other
corner case.
In order to facilitate the backporting I added "Fixes: 86039bd3b4e6"
however the side effect of this same race condition in /proc/pid/mem
should be reproducible since before 2.6.12-rc2 so I couldn't add any
other "Fixes:" because there's no hash beyond the git genesis commit.
Because find_extend_vma() is the only location outside of the process
context that could modify the "mm" structures under mmap_sem for
reading, by adding the mmget_still_valid() check to it, all other cases
that take the mmap_sem for reading don't need the new check after
mmget_not_zero()/get_task_mm(). The expand_stack() in page fault
context also doesn't need the new check, because all tasks under core
dumping are frozen.
Link: http://lkml.kernel.org/r/20190325224949.11068-1-aarcange@redhat.com
Fixes: 86039bd3b4 ("userfaultfd: add new syscall to provide memory externalization")
Signed-off-by: Andrea Arcangeli <aarcange@redhat.com>
Reported-by: Jann Horn <jannh@google.com>
Suggested-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Mike Rapoport <rppt@linux.ibm.com>
Reviewed-by: Oleg Nesterov <oleg@redhat.com>
Reviewed-by: Jann Horn <jannh@google.com>
Acked-by: Jason Gunthorpe <jgg@mellanox.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4a58038b9e upstream.
This reverts commit bb218fbcfa.
As Oren Twaig pointed out the old discussion:
https://patchwork.kernel.org/patch/8292231/
that the change coud potentially cause an extra IPI to be sent to
the destination vcpu because the AVIC hardware already set the IRR bit
before the incomplete IPI #VMEXIT with id=1 (target vcpu is not running).
Since writting to ICR and ICR2 will also set the IRR. If something triggers
the destination vcpu to get scheduled before the emulation finishes, then
this could result in an additional IPI.
Also, the issue mentioned in the commit bb218fbcfa was misdiagnosed.
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Reported-by: Oren Twaig <oren@scalemp.com>
Signed-off-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0228034d8e upstream.
This patch clears FC_RP_STARTED flag during logoff, because of this
re-login(flogi) didn't happen to the switch.
This reverts commit 1550ec458e.
Fixes: 1550ec458e ("scsi: fcoe: clear FC_RP_STARTED flags when receiving a LOGO")
Cc: <stable@vger.kernel.org> # v4.18+
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Reviewed-by: Hannes Reinecke <hare@#suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit be549d4911 upstream.
When SCSI blk-mq is enabled, there is a bug in handling errors in
scsi_queue_rq. Specifically, the bug is not setting result field of
scsi_request correctly when the dispatch of the command has been
failed. Since the upper layer code including the sg_io ioctl expects to
receive any error status from result field of scsi_request, the error is
silently ignored and this could cause data corruptions for some
applications.
Fixes: d285203cf6 ("scsi: add support for a blk-mq based I/O path.")
Cc: <stable@vger.kernel.org>
Signed-off-by: Jaesoo Lee <jalee@purestorage.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b2ecf00631 upstream.
The patch a6dbe44275 ("vt: perform safe console erase in the right
order") introduced a bug. The conditional do_update_region() was
replaced by a call to update_region() that does contain the conditional
already, but with unwanted extra side effects such as restoring the cursor
drawing.
In order to reproduce the bug:
- use framebuffer console with the AMDGPU driver
- type "links" to start the console www browser
- press 'q' and space to exit links
Now the cursor will be permanently visible in the center of the
screen. It will stay there until something overwrites it.
The bug goes away if we change update_region() back to the conditional
do_update_region().
[ nico: reworded changelog ]
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Reviewed-by: Nicolas Pitre <nico@fluxnic.net>
Cc: stable@vger.kernel.org
Fixes: a6dbe44275 ("vt: perform safe console erase in the right order")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ace965696d upstream.
There are several issues with the formula used for calculating the
deviation from the intended rate:
1. While min_err and last_stop are signed, srr and baud are unsigned.
Hence the signed values are promoted to unsigned, which will lead
to a bogus value of deviation if min_err is negative,
2. Srr is the register field value, which is one less than the actual
sampling rate factor,
3. The divisions do not use rounding.
Fix this by casting unsigned variables to int, adding one to srr, and
using a single DIV_ROUND_CLOSEST().
Fixes: 63ba1e00f1 ("serial: sh-sci: Support for HSCIF RX sampling point adjustment")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Mukesh Ojha <mojha@codeaurora.org>
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2a3f7221ac upstream.
There is a small race window in the card disconnection code that
allows the registration of another card with the very same card id.
This leads to a warning in procfs creation as caught by syzkaller.
The problem is that we delete snd_cards and snd_cards_lock entries at
the very beginning of the disconnection procedure. This makes the
slot available to be assigned for another card object while the
disconnection procedure is being processed. Then it becomes possible
to issue a procfs registration with the existing file name although we
check the conflict beforehand.
The fix is simply to move the snd_cards and snd_cards_lock clearances
at the end of the disconnection procedure. The references to these
entries are merely either from the global proc files like
/proc/asound/cards or from the card registration / disconnection, so
it should be fine to shift at the very end.
Reported-by: syzbot+48df349490c36f9f54ab@syzkaller.appspotmail.com
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b26e36b7ef upstream.
We have two Dell laptops which have the codec 10ec0236 and 10ec0256
respectively, the headset mic on them can't work, need to apply the
quirk of ALC255_FIXUP_DELL1_MIC_NO_PRESENCE. So adding their pin
configurations in the pin quirk table.
Cc: <stable@vger.kernel.org>
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit af4b54a2e5 upstream.
`ni6501_alloc_usb_buffers()` is called from `ni6501_auto_attach()` to
allocate RX and TX buffers for USB transfers. It allocates
`devpriv->usb_rx_buf` followed by `devpriv->usb_tx_buf`. If the
allocation of `devpriv->usb_tx_buf` fails, it frees
`devpriv->usb_rx_buf`, leaving the pointer set dangling, and returns an
error. Later, `ni6501_detach()` will be called from the core comedi
module code to clean up. `ni6501_detach()` also frees both
`devpriv->usb_rx_buf` and `devpriv->usb_tx_buf`, but
`devpriv->usb_rx_buf` may have already beed freed, leading to a
double-free error. Fix it bu removing the call to
`kfree(devpriv->usb_rx_buf)` from `ni6501_alloc_usb_buffers()`, relying
on `ni6501_detach()` to free the memory.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 660cf4ce9d upstream.
If `ni6501_auto_attach()` returns an error, the core comedi module code
will call `ni6501_detach()` to clean up. If `ni6501_auto_attach()`
successfully allocated the comedi device private data, `ni6501_detach()`
assumes that a `struct mutex mut` contained in the private data has been
initialized and uses it. Unfortunately, there are a couple of places
where `ni6501_auto_attach()` can return an error after allocating the
device private data but before initializing the mutex, so this
assumption is invalid. Fix it by initializing the mutex just after
allocating the private data in `ni6501_auto_attach()` before any other
errors can be retturned. Also move the call to `usb_set_intfdata()`
just to keep the code a bit neater (either position for the call is
fine).
I believe this was the cause of the following syzbot crash report
<https://syzkaller.appspot.com/bug?extid=cf4f2b6c24aff0a3edf6>:
usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
usb 1-1: config 0 descriptor??
usb 1-1: string descriptor 0 read error: -71
comedi comedi0: Wrong number of endpoints
ni6501 1-1:0.233: driver 'ni6501' failed to auto-configure device.
INFO: trying to register non-static key.
the code is fine but needs lockdep annotation.
turning off the locking correctness validator.
CPU: 0 PID: 585 Comm: kworker/0:3 Not tainted 5.1.0-rc4-319354-g9a33b36 #3
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Workqueue: usb_hub_wq hub_event
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0xe8/0x16e lib/dump_stack.c:113
assign_lock_key kernel/locking/lockdep.c:786 [inline]
register_lock_class+0x11b8/0x1250 kernel/locking/lockdep.c:1095
__lock_acquire+0xfb/0x37c0 kernel/locking/lockdep.c:3582
lock_acquire+0x10d/0x2f0 kernel/locking/lockdep.c:4211
__mutex_lock_common kernel/locking/mutex.c:925 [inline]
__mutex_lock+0xfe/0x12b0 kernel/locking/mutex.c:1072
ni6501_detach+0x5b/0x110 drivers/staging/comedi/drivers/ni_usb6501.c:567
comedi_device_detach+0xed/0x800 drivers/staging/comedi/drivers.c:204
comedi_device_cleanup.part.0+0x68/0x140 drivers/staging/comedi/comedi_fops.c:156
comedi_device_cleanup drivers/staging/comedi/comedi_fops.c:187 [inline]
comedi_free_board_dev.part.0+0x16/0x90 drivers/staging/comedi/comedi_fops.c:190
comedi_free_board_dev drivers/staging/comedi/comedi_fops.c:189 [inline]
comedi_release_hardware_device+0x111/0x140 drivers/staging/comedi/comedi_fops.c:2880
comedi_auto_config.cold+0x124/0x1b0 drivers/staging/comedi/drivers.c:1068
usb_probe_interface+0x31d/0x820 drivers/usb/core/driver.c:361
really_probe+0x2da/0xb10 drivers/base/dd.c:509
driver_probe_device+0x21d/0x350 drivers/base/dd.c:671
__device_attach_driver+0x1d8/0x290 drivers/base/dd.c:778
bus_for_each_drv+0x163/0x1e0 drivers/base/bus.c:454
__device_attach+0x223/0x3a0 drivers/base/dd.c:844
bus_probe_device+0x1f1/0x2a0 drivers/base/bus.c:514
device_add+0xad2/0x16e0 drivers/base/core.c:2106
usb_set_configuration+0xdf7/0x1740 drivers/usb/core/message.c:2021
generic_probe+0xa2/0xda drivers/usb/core/generic.c:210
usb_probe_device+0xc0/0x150 drivers/usb/core/driver.c:266
really_probe+0x2da/0xb10 drivers/base/dd.c:509
driver_probe_device+0x21d/0x350 drivers/base/dd.c:671
__device_attach_driver+0x1d8/0x290 drivers/base/dd.c:778
bus_for_each_drv+0x163/0x1e0 drivers/base/bus.c:454
__device_attach+0x223/0x3a0 drivers/base/dd.c:844
bus_probe_device+0x1f1/0x2a0 drivers/base/bus.c:514
device_add+0xad2/0x16e0 drivers/base/core.c:2106
usb_new_device.cold+0x537/0xccf drivers/usb/core/hub.c:2534
hub_port_connect drivers/usb/core/hub.c:5089 [inline]
hub_port_connect_change drivers/usb/core/hub.c:5204 [inline]
port_event drivers/usb/core/hub.c:5350 [inline]
hub_event+0x138e/0x3b00 drivers/usb/core/hub.c:5432
process_one_work+0x90f/0x1580 kernel/workqueue.c:2269
worker_thread+0x9b/0xe20 kernel/workqueue.c:2415
kthread+0x313/0x420 kernel/kthread.c:253
ret_from_fork+0x3a/0x50 arch/x86/entry/entry_64.S:352
Reported-by: syzbot+cf4f2b6c24aff0a3edf6@syzkaller.appspotmail.com
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 663d294b47 upstream.
`vmk80xx_alloc_usb_buffers()` is called from `vmk80xx_auto_attach()` to
allocate RX and TX buffers for USB transfers. It allocates
`devpriv->usb_rx_buf` followed by `devpriv->usb_tx_buf`. If the
allocation of `devpriv->usb_tx_buf` fails, it frees
`devpriv->usb_rx_buf`, leaving the pointer set dangling, and returns an
error. Later, `vmk80xx_detach()` will be called from the core comedi
module code to clean up. `vmk80xx_detach()` also frees both
`devpriv->usb_rx_buf` and `devpriv->usb_tx_buf`, but
`devpriv->usb_rx_buf` may have already been freed, leading to a
double-free error. Fix it by removing the call to
`kfree(devpriv->usb_rx_buf)` from `vmk80xx_alloc_usb_buffers()`, relying
on `vmk80xx_detach()` to free the memory.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 08b7c2f920 upstream.
If `vmk80xx_auto_attach()` returns an error, the core comedi module code
will call `vmk80xx_detach()` to clean up. If `vmk80xx_auto_attach()`
successfully allocated the comedi device private data,
`vmk80xx_detach()` assumes that a `struct semaphore limit_sem` contained
in the private data has been initialized and uses it. Unfortunately,
there are a couple of places where `vmk80xx_auto_attach()` can return an
error after allocating the device private data but before initializing
the semaphore, so this assumption is invalid. Fix it by initializing
the semaphore just after allocating the private data in
`vmk80xx_auto_attach()` before any other errors can be returned.
I believe this was the cause of the following syzbot crash report
<https://syzkaller.appspot.com/bug?extid=54c2f58f15fe6876b6ad>:
usb 1-1: config 0 has no interface number 0
usb 1-1: New USB device found, idVendor=10cf, idProduct=8068, bcdDevice=e6.8d
usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
usb 1-1: config 0 descriptor??
vmk80xx 1-1:0.117: driver 'vmk80xx' failed to auto-configure device.
INFO: trying to register non-static key.
the code is fine but needs lockdep annotation.
turning off the locking correctness validator.
CPU: 0 PID: 12 Comm: kworker/0:1 Not tainted 5.1.0-rc4-319354-g9a33b36 #3
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Workqueue: usb_hub_wq hub_event
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0xe8/0x16e lib/dump_stack.c:113
assign_lock_key kernel/locking/lockdep.c:786 [inline]
register_lock_class+0x11b8/0x1250 kernel/locking/lockdep.c:1095
__lock_acquire+0xfb/0x37c0 kernel/locking/lockdep.c:3582
lock_acquire+0x10d/0x2f0 kernel/locking/lockdep.c:4211
__raw_spin_lock_irqsave include/linux/spinlock_api_smp.h:110 [inline]
_raw_spin_lock_irqsave+0x44/0x60 kernel/locking/spinlock.c:152
down+0x12/0x80 kernel/locking/semaphore.c:58
vmk80xx_detach+0x59/0x100 drivers/staging/comedi/drivers/vmk80xx.c:829
comedi_device_detach+0xed/0x800 drivers/staging/comedi/drivers.c:204
comedi_device_cleanup.part.0+0x68/0x140 drivers/staging/comedi/comedi_fops.c:156
comedi_device_cleanup drivers/staging/comedi/comedi_fops.c:187 [inline]
comedi_free_board_dev.part.0+0x16/0x90 drivers/staging/comedi/comedi_fops.c:190
comedi_free_board_dev drivers/staging/comedi/comedi_fops.c:189 [inline]
comedi_release_hardware_device+0x111/0x140 drivers/staging/comedi/comedi_fops.c:2880
comedi_auto_config.cold+0x124/0x1b0 drivers/staging/comedi/drivers.c:1068
usb_probe_interface+0x31d/0x820 drivers/usb/core/driver.c:361
really_probe+0x2da/0xb10 drivers/base/dd.c:509
driver_probe_device+0x21d/0x350 drivers/base/dd.c:671
__device_attach_driver+0x1d8/0x290 drivers/base/dd.c:778
bus_for_each_drv+0x163/0x1e0 drivers/base/bus.c:454
__device_attach+0x223/0x3a0 drivers/base/dd.c:844
bus_probe_device+0x1f1/0x2a0 drivers/base/bus.c:514
device_add+0xad2/0x16e0 drivers/base/core.c:2106
usb_set_configuration+0xdf7/0x1740 drivers/usb/core/message.c:2021
generic_probe+0xa2/0xda drivers/usb/core/generic.c:210
usb_probe_device+0xc0/0x150 drivers/usb/core/driver.c:266
really_probe+0x2da/0xb10 drivers/base/dd.c:509
driver_probe_device+0x21d/0x350 drivers/base/dd.c:671
__device_attach_driver+0x1d8/0x290 drivers/base/dd.c:778
bus_for_each_drv+0x163/0x1e0 drivers/base/bus.c:454
__device_attach+0x223/0x3a0 drivers/base/dd.c:844
bus_probe_device+0x1f1/0x2a0 drivers/base/bus.c:514
device_add+0xad2/0x16e0 drivers/base/core.c:2106
usb_new_device.cold+0x537/0xccf drivers/usb/core/hub.c:2534
hub_port_connect drivers/usb/core/hub.c:5089 [inline]
hub_port_connect_change drivers/usb/core/hub.c:5204 [inline]
port_event drivers/usb/core/hub.c:5350 [inline]
hub_event+0x138e/0x3b00 drivers/usb/core/hub.c:5432
process_one_work+0x90f/0x1580 kernel/workqueue.c:2269
worker_thread+0x9b/0xe20 kernel/workqueue.c:2415
kthread+0x313/0x420 kernel/kthread.c:253
ret_from_fork+0x3a/0x50 arch/x86/entry/entry_64.S:352
Reported-by: syzbot+54c2f58f15fe6876b6ad@syzkaller.appspotmail.com
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 131ac62253 upstream.
This patch uses the device description to clearly identity a device
attached to the bus. It is needed as the currently useed mdevX
notation is not sufficiant in case more than one network
interface controller is being used at the same time.
Cc: stable@vger.kernel.org
Signed-off-by: Christian Gromm <christian.gromm@microchip.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7f75591fc5 upstream.
This fixes a possible circular locking dependency detected warning seen
with:
- CONFIG_PROVE_LOCKING=y
- consumer/provider IIO devices (ex: "voltage-divider" consumer of "adc")
When using the IIO consumer interface, e.g. iio_channel_get(), the consumer
device will likely call iio_read_channel_raw() or similar that rely on
'info_exist_lock' mutex.
typically:
...
mutex_lock(&chan->indio_dev->info_exist_lock);
if (chan->indio_dev->info == NULL) {
ret = -ENODEV;
goto err_unlock;
}
ret = do_some_ops()
err_unlock:
mutex_unlock(&chan->indio_dev->info_exist_lock);
return ret;
...
Same mutex is also hold in iio_device_unregister().
The following deadlock warning happens when:
- the consumer device has called an API like iio_read_channel_raw()
at least once.
- the consumer driver is unregistered, removed (unbind from sysfs)
======================================================
WARNING: possible circular locking dependency detected
4.19.24 #577 Not tainted
------------------------------------------------------
sh/372 is trying to acquire lock:
(kn->count#30){++++}, at: kernfs_remove_by_name_ns+0x3c/0x84
but task is already holding lock:
(&dev->info_exist_lock){+.+.}, at: iio_device_unregister+0x18/0x60
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #1 (&dev->info_exist_lock){+.+.}:
__mutex_lock+0x70/0xa3c
mutex_lock_nested+0x1c/0x24
iio_read_channel_raw+0x1c/0x60
iio_read_channel_info+0xa8/0xb0
dev_attr_show+0x1c/0x48
sysfs_kf_seq_show+0x84/0xec
seq_read+0x154/0x528
__vfs_read+0x2c/0x15c
vfs_read+0x8c/0x110
ksys_read+0x4c/0xac
ret_fast_syscall+0x0/0x28
0xbedefb60
-> #0 (kn->count#30){++++}:
lock_acquire+0xd8/0x268
__kernfs_remove+0x288/0x374
kernfs_remove_by_name_ns+0x3c/0x84
remove_files+0x34/0x78
sysfs_remove_group+0x40/0x9c
sysfs_remove_groups+0x24/0x34
device_remove_attrs+0x38/0x64
device_del+0x11c/0x360
cdev_device_del+0x14/0x2c
iio_device_unregister+0x24/0x60
release_nodes+0x1bc/0x200
device_release_driver_internal+0x1a0/0x230
unbind_store+0x80/0x130
kernfs_fop_write+0x100/0x1e4
__vfs_write+0x2c/0x160
vfs_write+0xa4/0x17c
ksys_write+0x4c/0xac
ret_fast_syscall+0x0/0x28
0xbe906840
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(&dev->info_exist_lock);
lock(kn->count#30);
lock(&dev->info_exist_lock);
lock(kn->count#30);
*** DEADLOCK ***
...
cdev_device_del() can be called without holding the lock. It should be safe
as info_exist_lock prevents kernelspace consumers to use the exported
routines during/after provider removal. cdev_device_del() is for userspace.
Help to reproduce:
See example: Documentation/devicetree/bindings/iio/afe/voltage-divider.txt
sysv {
compatible = "voltage-divider";
io-channels = <&adc 0>;
output-ohms = <22>;
full-ohms = <222>;
};
First, go to iio:deviceX for the "voltage-divider", do one read:
$ cd /sys/bus/iio/devices/iio:deviceX
$ cat in_voltage0_raw
Then, unbind the consumer driver. It triggers above deadlock warning.
$ cd /sys/bus/platform/drivers/iio-rescale/
$ echo sysv > unbind
Note I don't actually expect stable will pick this up all the
way back into IIO being in staging, but if's probably valid that
far back.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Fixes: ac917a8111 ("staging:iio:core set the iio_dev.info pointer to null on unregister")
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 09c6bdee51 upstream.
Having a brief look at at91_adc_read_raw() it is obvious that in the case
of a timeout the setting of AT91_ADC_CHDR and AT91_ADC_IDR registers is
omitted. If 2 different channels are queried we can end up with a
situation where two interrupts are enabled, but only one interrupt is
cleared in the interrupt handler. Resulting in a interrupt loop and a
system hang.
Signed-off-by: Georg Ottinger <g.ottinger@abatec.at>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 20ea39ef9f upstream.
The trialmask is expected to have all bits set to 0 after allocation.
Currently kmalloc_array() is used which does not zero the memory and so
random bits are set. This results in random channels being enabled when
they shouldn't. Replace kmalloc_array() with kcalloc() which has the same
interface but zeros the memory.
Note the fix is actually required earlier than the below fixes tag, but
will require a manual backport due to move from kmalloc to kmalloc_array.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Fixes commit 057ac1acdf ("iio: Use kmalloc_array() in iio_scan_mask_set()").
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0600353150 upstream.
When issuing the write DAC register and write eeprom command, the two
powerdown bits (PD0 and PD1) are assumed by the chip to be present in
the bytes sent. Leaving them at 0 implies "powerdown disabled" which is
a different state that the current one. By adding the current state of
the powerdown in the i2c write, the chip will correctly power-on exactly
like as it is at the moment of store_eeprom call.
This is documented in MCP4725's datasheet, FIGURE 6-2: "Write Commands
for DAC Input Register and EEPROM" and MCP4726's datasheet, FIGURE 6-3:
"Write All Memory Command".
Signed-off-by: Jean-Francois Dagenais <jeff.dagenais@gmail.com>
Acked-by: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3d02d7082e upstream.
Calculation did not use IIO_DEGREE_TO_RAD and implemented a variant to
avoid precision loss as we aim a nano value. The offset added to avoid
rounding error, though, doesn't give us a close result to the expected
value. E.g.
For 1000dps, the result should be:
(1000 * pi ) / 180 >> 15 ~= 0.000532632218
But with current calculation we get
$ cat scale
0.000547890
Fix the calculation by just doing the maths involved for a nano value
val * pi * 10e12 / (180 * 2^15)
so we get a closer result.
$ cat scale
0.000532632
Fixes: c14dca07a3 ("iio: cros_ec_sensors: add ChromeOS EC Contiguous Sensors driver")
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 73f3bc6da5 upstream.
The SPI interface implementation was completely broken.
When using the SPI interface, there are only 7 address bits, the upper bit
is controlled by a page select register. The core needs access to both
ranges, so implement register read/write for both regions. The regmap
paging functionality didn't agree with a register that needs to be read
and modified, so I implemented a custom paging algorithm.
This fixes that the device wouldn't even probe in SPI mode.
The SPI interface then isn't different from I2C, merged them into the core,
and the I2C/SPI named registers are no longer needed.
Implemented register value caching for the registers to reduce the I2C/SPI
data transfers considerably.
The calibration set reads as all zeroes until some undefined point in time,
and I couldn't determine what makes it valid. The datasheet mentions these
registers but does not provide any hints on when they become valid, and they
aren't even enumerated in the memory map. So check the calibration and
retry reading it from the device after each measurement until it provides
something valid.
Despite the size this is suitable for a stable backport given that
it seems the SPI support never worked.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Fixes: 1b3bd85927 ("iio: chemical: Add support for Bosch BME680 sensor");
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 99c221796a upstream.
I noticed that apic test from kvm-unit-tests always hangs on my EPYC 7401P,
the hanging test nmi-after-sti is trying to deliver 30000 NMIs and tracing
shows that we're sometimes able to deliver a few but never all.
When we're trying to inject an NMI we may fail to do so immediately for
various reasons, however, we still need to inject it so enable_nmi_window()
arms nmi_singlestep mode. #DB occurs as expected, but we're not checking
for pending NMIs before entering the guest and unless there's a different
event to process, the NMI will never get delivered.
Make KVM_REQ_EVENT request on the vCPU from db_interception() to make sure
pending NMIs are checked and possibly injected.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8f4dc2e77c upstream.
Neither AMD nor Intel CPUs have an EFER field in the legacy SMRAM save
state area, i.e. don't save/restore EFER across SMM transitions. KVM
somewhat models this, e.g. doesn't clear EFER on entry to SMM if the
guest doesn't support long mode. But during RSM, KVM unconditionally
clears EFER so that it can get back to pure 32-bit mode in order to
start loading CRs with their actual non-SMM values.
Clear EFER only when it will be written when loading the non-SMM state
so as to preserve bits that can theoretically be set on 32-bit vCPUs,
e.g. KVM always emulates EFER_SCE.
And because CR4.PAE is cleared only to play nice with EFER, wrap that
code in the long mode check as well. Note, this may result in a
compiler warning about cr4 being consumed uninitialized. Re-read CR4
even though it's technically unnecessary, as doing so allows for more
readable code and RSM emulation is not a performance critical path.
Fixes: 660a5d517a ("KVM: x86: save/load state on SMM switch")
Cc: stable@vger.kernel.org
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e6d0fb7b34 upstream.
If we enter smb2_query_symlink() for something that is not a symlink
and where the SMB2_open() would succeed we would never end up
closing this handle and would thus leak a handle on the server.
Fix this by immediately calling SMB2_close() on successfull open.
Signed-off-by: Ronnie Sahlberg <lsahlber@redhat.com>
CC: Stable <stable@vger.kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
Reviewed-by: Pavel Shilovsky <pshilov@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 088aaf17aa upstream.
There is a KASAN use-after-free:
BUG: KASAN: use-after-free in SMB2_read+0x1136/0x1190
Read of size 8 at addr ffff8880b4e45e50 by task ln/1009
Should not release the 'req' because it will use in the trace.
Fixes: eccb4422cf ("smb3: Add ftrace tracepoints for improved SMB3 debugging")
Signed-off-by: ZhangXiaoxu <zhangxiaoxu5@huawei.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
CC: Stable <stable@vger.kernel.org> 4.18+
Reviewed-by: Pavel Shilovsky <pshilov@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6a3eb33606 upstream.
There is a KASAN use-after-free:
BUG: KASAN: use-after-free in SMB2_write+0x1342/0x1580
Read of size 8 at addr ffff8880b6a8e450 by task ln/4196
Should not release the 'req' because it will use in the trace.
Fixes: eccb4422cf ("smb3: Add ftrace tracepoints for improved SMB3 debugging")
Signed-off-by: ZhangXiaoxu <zhangxiaoxu5@huawei.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
CC: Stable <stable@vger.kernel.org> 4.18+
Reviewed-by: Pavel Shilovsky <pshilov@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b98749cac4 upstream.
In the oplock break handler, writing pending changes from pages puts
the FileInfo handle. If the refcount reaches zero it closes the handle
and waits for any oplock break handler to return, thus causing a deadlock.
To prevent this situation:
* We add a wait flag to cifsFileInfo_put() to decide whether we should
wait for running/pending oplock break handlers
* We keep an additionnal reference of the SMB FileInfo handle so that
for the rest of the handler putting the handle won't close it.
- The ref is bumped everytime we queue the handler via the
cifs_queue_oplock_break() helper.
- The ref is decremented at the end of the handler
This bug was triggered by xfstest 464.
Also important fix to address the various reports of
oops in smb2_push_mandatory_locks
Signed-off-by: Aurelien Aptel <aaptel@suse.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Reviewed-by: Pavel Shilovsky <pshilov@microsoft.com>
CC: Stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 997dd96471 ]
Currently, IPv6 defragmentation code drops non-last fragments that
are smaller than 1280 bytes: see
commit 0ed4229b08 ("ipv6: defrag: drop non-last frags smaller than min mtu")
This behavior is not specified in IPv6 RFCs and appears to break
compatibility with some IPv6 implemenations, as reported here:
https://www.spinics.net/lists/netdev/msg543846.html
This patch re-uses common IP defragmentation queueing and reassembly
code in IP6 defragmentation in nf_conntrack, removing the 1280 byte
restriction.
Signed-off-by: Peter Oskolkov <posk@google.com>
Reported-by: Tom Herbert <tom@herbertland.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d4289fcc9b ]
Currently, IPv6 defragmentation code drops non-last fragments that
are smaller than 1280 bytes: see
commit 0ed4229b08 ("ipv6: defrag: drop non-last frags smaller than min mtu")
This behavior is not specified in IPv6 RFCs and appears to break
compatibility with some IPv6 implemenations, as reported here:
https://www.spinics.net/lists/netdev/msg543846.html
This patch re-uses common IP defragmentation queueing and reassembly
code in IPv6, removing the 1280 byte restriction.
v2: change handling of overlaps to match that of upstream.
Signed-off-by: Peter Oskolkov <posk@google.com>
Reported-by: Tom Herbert <tom@herbertland.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c23f35d19d ]
This is a refactoring patch: without changing runtime behavior,
it moves rbtree-related code from IPv4-specific files/functions
into .h/.c defrag files shared with IPv6 defragmentation code.
v2: make handling of overlapping packets match upstream.
Signed-off-by: Peter Oskolkov <posk@google.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Florian Westphal <fw@strlen.de>
Cc: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4976e3c683 ]
The logic in cake_select_tin() was getting a bit hairy, and it turns out we
can simplify it quite a bit. This also allows us to get rid of one of the
two diffserv parsing functions, which has the added benefit that
already-zeroed DSCP fields won't get re-written.
Suggested-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f7ee799a51 ]
Replace vlan CFI bit with a vlan present bit that indicates the
presence of a vlan tag. Previously the driver incorrectly assumed
that an vlan id of 0 is not matchable, therefore we indicate vlan
presence with a vlan present bit.
Fixes: 5571e8c9f2 ("nfp: extend flower matching capabilities")
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Signed-off-by: Louis Peens <louis.peens@netronome.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c87b4ecdbe ]
There is not actually any guarantee that the IP headers are valid before we
access the DSCP bits of the packets. Fix this using the same approach taken
in sch_dsmark.
Reported-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b2100cc56f ]
We shouldn't be using skb->protocol directly as that will miss cases with
hardware-accelerated VLAN tags. Use the helper instead to get the right
protocol number.
Reported-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit df3a8344d4 ]
Flow is kfreed on mlx5_fpga_tls_del_flow but kept in the idr data
structure, this is risky and can cause use-after-free, since the
idr_remove is delayed until tls_send_teardown_cmd completion.
Instead of delaying idr_remove, in this patch we do it on
mlx5_fpga_tls_del_flow, before actually kfree(flow).
Added synchronize_rcu before kfree(flow)
Fixes: ab412e1dd7 ("net/mlx5: Accel, add TLS rx offload routines")
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b4f47f3848 ]
Unlike '&&' operator, the '&' does not have short-circuit
evaluation semantics. IOW both sides of the operator always
get evaluated. Fix the wrong operator in
tls_is_sk_tx_device_offloaded(), which would lead to
out-of-bounds access for for non-full sockets.
Fixes: 4799ac81e5 ("tls: Add rx inline crypto offload")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 31634bf5dc ]
To avoid use-after-free, hold the rcu read lock until we are done copying
flow data into the command buffer.
Fixes: ab412e1dd7 ("net/mlx5: Accel, add TLS rx offload routines")
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1f227d1608 ]
The thunderx driver forbids to load an eBPF program if the MTU is too high,
but this can be circumvented by loading the eBPF, then raising the MTU.
Fix this by limiting the MTU if an eBPF program is already loaded.
Fixes: 05c773f52b ("net: thunderx: Add basic XDP support")
Signed-off-by: Matteo Croce <mcroce@redhat.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5ee15c101f ]
The thunderx driver splits frames bigger than 1530 bytes to multiple
pages, making impossible to run an eBPF program on it.
This leads to a maximum MTU of 1508 if QinQ is in use.
The thunderx driver forbids to load an eBPF program if the MTU is higher
than 1500 bytes. Raise the limit to 1508 so it is possible to use L2
protocols which need some more headroom.
Fixes: 05c773f52b ("net: thunderx: Add basic XDP support")
Signed-off-by: Matteo Croce <mcroce@redhat.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
