[ Upstream commit f03508ce3f ]
The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, so make sure the implementation in
this driver has returns 'netdev_tx_t' value, and change the function
return type to netdev_tx_t.
Found by coccinelle.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 70afb58e98 ]
The Marvell PPv2.2 engine only has 8 Rx queues per CPU, while PPv2.1 has
16 of them. This patch updates the code so that the Rx queues mask width
is selected given the version of the network controller used.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 079cdff3d0 ]
This avoids getting woken up from suspend after power interruptions
when the bci wrongly thinks the battery is full just because
of input current going low because of low input power
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8314c212f9 ]
the charging current uses unsigned int variables, if we step back
if the current is still low, we would run into negative which
means setting the target to a huge value.
Better add checks here.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 62287dce5d ]
dtc has new checks for I2C buses. Fix the warnings in unit-addresses in
the unittests.
drivers/of/unittest-data/testcases.dtb: Warning (i2c_bus_reg): /testcase-data/overlay-node/test-bus/i2c-test-bus/test-unittest14/i2c@0/test-mux-dev: I2C bus unit address format error, expected "20"
drivers/of/unittest-data/overlay_15.dtb: Warning (i2c_bus_reg): /fragment@0/__overlay__/test-unittest15/i2c@0/test-mux-dev: I2C bus unit address format error, expected "20"
Cc: Frank Rowand <frowand.list@gmail.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3d2556992a ]
The dev_list needs to be protected with a lock, else we may have
simultaneous access (addition/removal) to it and that would be racy.
Extend scope of the opp_table lock to protect dev_list as well.
Tested-by: Niklas Cassel <niklas.cassel@linaro.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c890ecdbe9 ]
dtc has new checks for I2C and SPI buses. Fix the warnings in node names
and unit-addresses.
arch/arm/boot/dts/at91-dvk_som60.dtb: Warning (i2c_bus_reg): /ahb/apb/i2c@f0018000/eeprom@87: I2C bus unit address format error, expected "57"
arch/arm/boot/dts/at91-dvk_som60.dtb: Warning (i2c_bus_reg): /ahb/apb/i2c@f0018000/ft5426@56: I2C bus unit address format error, expected "38"
arch/arm/boot/dts/at91-vinco.dtb: Warning (i2c_bus_reg): /ahb/apb/i2c@f8024000/rtc@64: I2C bus unit address format error, expected "32"
arch/arm/boot/dts/at91sam9260ek.dtb: Warning (spi_bus_reg): /ahb/apb/spi@fffc8000/mtd_dataflash@0: SPI bus unit address format error, expected "1"
arch/arm/boot/dts/at91sam9g20ek_2mmc.dtb: Warning (spi_bus_reg): /ahb/apb/spi@fffc8000/mtd_dataflash@0: SPI bus unit address format error, expected "1"
arch/arm/boot/dts/at91sam9g20ek.dtb: Warning (spi_bus_reg): /ahb/apb/spi@fffc8000/mtd_dataflash@0: SPI bus unit address format error, expected "1"
arch/arm/boot/dts/at91sam9261ek.dtb: Warning (spi_bus_reg): /ahb/apb/spi@fffc8000/tsc2046@0: SPI bus unit address format error, expected "2"
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 802fa45cd3 ]
Commit f27b4746f3 ("i40iw: add connection management code") uses an
incorrect rcu iterator, whilst holding the rtnl_lock. Since the
critical region invokes i40iw_manage_qhash(), which is a sleeping
function, the rcu locking and traversal cannot be used.
Signed-off-by: Håkon Bugge <haakon.bugge@oracle.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e00d93ac9a ]
This re-applies commit b91c1e3e7a ("powerpc: Fix duplicate const
clang warning in user access code") (Jun 2015) which was undone in
commits:
f2ca809059 ("powerpc/sparse: Constify the address pointer in __get_user_nosleep()") (Feb 2017)
d466f6c5ca ("powerpc/sparse: Constify the address pointer in __get_user_nocheck()") (Feb 2017)
f84ed59a61 ("powerpc/sparse: Constify the address pointer in __get_user_check()") (Feb 2017)
We see a large number of duplicate const errors in the user access
code when building with llvm/clang:
include/linux/pagemap.h:576:8: warning: duplicate 'const' declaration specifier [-Wduplicate-decl-specifier]
ret = __get_user(c, uaddr);
The problem is we are doing const __typeof__(*(ptr)), which will hit
the warning if ptr is marked const.
Removing const does not seem to have any effect on GCC code
generation.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 85a88cabad ]
When performing partition migrations all present CPUs must be online
as all present CPUs must make the H_JOIN call as part of the migration
process. Once all present CPUs make the H_JOIN call, one CPU is returned
to make the rtas call to perform the migration to the destination system.
During testing of migration and changing the SMT state we have found
instances where CPUs are offlined, as part of the SMT state change,
before they make the H_JOIN call. This results in a hung system where
every CPU is either in H_JOIN or offline.
To prevent this this patch disables CPU hotplug during the migration
process.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Reviewed-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 063b8b1251 ]
The updates to powerpc numa and memory hotplug code now use the
in-kernel LMB array instead of the device tree. This change allows the
pseries memory DLPAR code to only update the device tree once after
successfully handling a DLPAR request.
Prior to the in-kernel LMB array, the numa code looked up the affinity
for memory being added in the device tree, the code now looks this up
in the LMB array. This change means the memory hotplug code can just
update the affinity for an LMB in the LMB array instead of updating
the device tree.
This also provides a savings in kernel memory. When updating the
device tree old properties are never free'ed since there is no
usecount on properties. This behavior leads to a new copy of the
property being allocated every time a LMB is added or removed (i.e. a
request to add 100 LMBs creates 100 new copies of the property). With
this update only a single new property is created when a DLPAR request
completes successfully.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 09b4438db1 ]
This causes SLB alloation to start 1 beyond the start of the SLB.
There is no real problem because after it wraps it stats behaving
properly, it's just surprisig to see when looking at SLB traces.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 44d947eff1 ]
There are cases where the test is not expecting to have the transaction
aborted, but, the test process might have been rescheduled, either in the
OS level or by KVM (if it is running on a KVM guest machine). The process
reschedule will cause a treclaim/recheckpoint which will cause the
transaction to doom, aborting the transaction as soon as the process is
rescheduled back to the CPU. This might cause the test to fail, but this is
not a failure in essence.
If that is the case, TEXASR[FC] is indicated with either
TM_CAUSE_RESCHEDULE or TM_CAUSE_KVM_RESCHEDULE for KVM interruptions.
In this scenario, ignore these two failures and avoid the whole test to
return failure.
Signed-off-by: Breno Leitao <leitao@debian.org>
Reviewed-by: Gustavo Romero <gromero@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 984ecdd68d ]
The tbl pointer is being derefenced by IOMMU_PAGE_SIZE prior the check
if it is not NULL.
Just moving the dereference code to after the check, where there will
be guarantee that 'tbl' will not be NULL.
Signed-off-by: Breno Leitao <leitao@debian.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 94b2bb28db ]
The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, so make sure the implementation in
this driver has returns 'netdev_tx_t' value, and change the function
return type to netdev_tx_t.
Found by coccinelle.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ac1172dea1 ]
The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, so make sure the implementation in
this driver has returns 'netdev_tx_t' value, and change the function
return type to netdev_tx_t.
Found by coccinelle.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c9c3941186 ]
The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, also the implementation in this
driver has returns 'netdev_tx_t' value, so just change the function
return type to netdev_tx_t.
Found by coccinelle.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 060e8fb53f ]
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/char/ipmi/ipmi_msghandler.c: In function 'ipmi_set_my_LUN':
drivers/char/ipmi/ipmi_msghandler.c:1335:13: warning:
variable 'rv' set but not used [-Wunused-but-set-variable]
int index, rv = 0;
'rv' should be the correct return value.
Fixes: 048f7c3e35 ("ipmi: Properly release srcu locks on error conditions")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1574608f5f ]
Looking at logs from systems all over the place, it looks like tons
of broken systems exist that set the base address to zero. I can
only guess that is some sort of non-standard idea to mark the
interface as not being present. It can't be zero, anyway, so just
complain and ignore it.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 97a103e6b5 ]
Shifting unsigned char b by an int type can lead to sign-extension
overflow. For example, if b is 0xff and the shift is 24, then top
bit is sign-extended so the final value passed to writeq has all
the upper 32 bits set. Fix this by casting b to a 64 bit unsigned
before the shift.
Detected by CoverityScan, CID#1465246 ("Unintended sign extension")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 01508d9ebf ]
I noticed that 4.17.0 logs the follwing during ipmi_si setup:
ipmi_si 0000:01:04.6: probing via PCI
(NULL device *): Could not setup I/O space
ipmi_si 0000:01:04.6: [mem 0xf5ef0000-0xf5ef00ff] regsize 1 spacing 1 irq 21
Fix the "NULL device *) by moving io.dev assignment before its potential
use by ipmi_pci_probe_regspacing().
Result:
ipmi_si 0000:01:04.6: probing via PCI
ipmi_si 0000:01:04.6: Could not setup I/O space
ipmi_si 0000:01:04.6: [mem 0xf5ef0000-0xf5ef00ff] regsize 1 spacing 1 irq 21
Signed-off-by: Meelis Roos <mroos@linux.ee>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 28b20dde5e ]
This patch fixed the boost volume at the begining of playback
while DAC volume set to lower level.
Signed-off-by: Shuming Fan <shumingf@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 00bca73bfc ]
Mediatek SPI driver modifies some fields (tx_buf, rx_buf, len, tx_dma,
rx_dma) of the spi_transfer* passed in when doing transfer_one and in
interrupt handler. This is somewhat unexpected, and there are some
caller (e.g. Cr50 spi driver) that reuse the spi_transfer for multiple
messages. Add a field to record how many bytes have been transferred,
and calculate the right len / buffer based on it instead.
Signed-off-by: Pi-Hsun Shih <pihsun@chromium.org>
Change-Id: I23e218cd964f16c0b2b26127d4a5ca6529867673
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0fd85869c2 ]
If the pll clock needs to be enabled to get its rate, it will also need
to be enabled to provide it. So ensure it is kept enabled through the
lifetime of the device.
Fixes: 0d7412ed1f ("spi/bcm63xx-hspi: Enable the clock before calling clk_get_rate().")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 534e0e52bc ]
samples/bpf build failed with the following errors:
$ make samples/bpf/
...
HOSTCC samples/bpf/sockex3_user.o
/data/users/yhs/work/net-next/samples/bpf/sockex3_user.c:16:8: error: redefinition of ‘struct bpf_flow_keys’
struct bpf_flow_keys {
^
In file included from /data/users/yhs/work/net-next/samples/bpf/sockex3_user.c:4:0:
./usr/include/linux/bpf.h:2338:9: note: originally defined here
struct bpf_flow_keys *flow_keys;
^
make[3]: *** [samples/bpf/sockex3_user.o] Error 1
Commit d58e468b11 ("flow_dissector: implements flow dissector BPF hook")
introduced struct bpf_flow_keys in include/uapi/linux/bpf.h and hence
caused the naming conflict with samples/bpf/sockex3_user.c.
The fix is to rename struct bpf_flow_keys in samples/bpf/sockex3_user.c
to flow_keys to avoid the conflict.
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3bc1572068 ]
AM65 has two PCIe controllers and each PCIe controller has '2' address
spaces one within the 4GB address space of the SoC and the other above
the 4GB address space of the SoC (cbass_main) in addition to the
register space. The size of the address space above the 4GB SoC address
space is 4GB. These address ranges will be used by CPU/DMA to access
the PCIe address space. In order to represent the address space above
the 4GB SoC address space and to represent the size of this address
space as 4GB, change address-cells and size-cells of interconnect to 2.
Since OSPI has similar need in MCU Domain Memory Map, change
address-cells and size-cells of cbass_mcu interconnect also to 2.
Fixes: ea47eed33a ("arm64: dts: ti: Add Support for AM654 SoC")
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Vignesh R <vigneshr@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c362272bde ]
If you've got the "console" serial port setup to use just as a UART
(AKA there is no "console=ttyMSMX" on the kernel command line) then
certain initialization is skipped. When userspace later tries to do
something with the port then things go boom (specifically, on my
system, some sort of exception hit that caused the system to reboot
itself w/ no error messages).
Let's cleanup / refactor the init so that we always run the same init
code regardless of whether we're using the console.
To make this work, we make rely on qcom_geni_serial_pm doing its job
to turn resources on.
For the record, here is a trace of the order of things (after this
patch) when console= is specified on the command line and we have an
agetty on the port:
qcom_geni_serial_pm: 4 (undefined) => 0 (on)
qcom_geni_console_setup
qcom_geni_serial_port_setup
qcom_geni_serial_console_write
qcom_geni_serial_startup
qcom_geni_serial_start_tx
...and here is the order of things (after this patch) when console= is
_NOT_ specified on the command line and we have an agetty port:
qcom_geni_serial_pm: 4 => 0
qcom_geni_serial_pm: 0 => 3
qcom_geni_serial_pm: 3 => 0
qcom_geni_serial_startup
qcom_geni_serial_port_setup
qcom_geni_serial_pm: 0 => 3
qcom_geni_serial_pm: 3 => 0
qcom_geni_serial_startup
qcom_geni_serial_start_tx
Fixes: c4f528795d ("tty: serial: msm_geni_serial: Add serial driver support for GENI based QUP")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5963e8a312 ]
On the error path of mxs_auart_request_gpio_irq() is performed
backward iterating with index i of enum type. Underline enum type
may be unsigned char. In this case check (--i >= 0) will be always
true and error handling goes into infinite loop.
The patch changes the check so that it is valid for signed and unsigned
types.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Anton Vasilyev <vasilyev@ispras.ru>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1ff3652bc7 ]
Ensure that the baud clock is also enabled for UART register writes in
driver resume. On Exynos5433 SoC this is needed to avoid external abort
issue.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4b9d33c6a3 ]
The driver's suspend/resume functions were buggy.
If UART node contains any child node in the DT and
the child is established a communication path with
the parent UART. The relevant /dev/ttyPS* node will
be not available for other operations.
If the driver is trying to do any operations like
suspend/resume without checking the tty->dev status
it leads to the kernel crash/hang.
This patch fix this issue by call the device_may_wake()
with the generic parameter of type struct device.
in the uart suspend and resume paths.
It also fixes a race condition in the uart suspend
path(i.e uart_suspend_port() should be called at the
end of cdns_uart_suspend API this path updates the same)
Signed-off-by: Nava kishore Manne <navam@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f5054ceed4 ]
dtc has new checks for I2C and SPI buses. Fix the warnings in node names
and unit-addresses.
arch/arm/boot/dts/zynq-zc702.dtb: Warning (i2c_bus_reg): /amba/i2c@e0004000/i2c-mux@74/i2c@7/hwmon@52: I2C bus unit address format error, expected "34"
arch/arm/boot/dts/zynq-zc702.dtb: Warning (i2c_bus_reg): /amba/i2c@e0004000/i2c-mux@74/i2c@7/hwmon@53: I2C bus unit address format error, expected "35"
arch/arm/boot/dts/zynq-zc702.dtb: Warning (i2c_bus_reg): /amba/i2c@e0004000/i2c-mux@74/i2c@7/hwmon@54: I2C bus unit address format error, expected "36"
arch/arm/boot/dts/zynq-zc770-xm013.dtb: Warning (spi_bus_reg): /amba/spi@e0006000/eeprom@0: SPI bus unit address format error, expected "2"
arch/arm/boot/dts/zynq-zc770-xm010.dtb: Warning (spi_bus_reg): /amba/spi@e0007000/flash@0: SPI bus unit address format error, expected "1"
Cc: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0020f5c807 ]
The driver may sleep with holding a spinlock.
The function call paths (from bottom to top) in Linux-4.17 are:
[FUNC] usleep_range
drivers/net/ethernet/socionext/sni_ave.c, 892:
usleep_range in ave_rxfifo_reset
drivers/net/ethernet/socionext/sni_ave.c, 932:
ave_rxfifo_reset in ave_irq_handler
[FUNC] usleep_range
drivers/net/ethernet/socionext/sni_ave.c, 888:
usleep_range in ave_rxfifo_reset
drivers/net/ethernet/socionext/sni_ave.c, 932:
ave_rxfifo_reset in ave_irq_handler
To fix these bugs, usleep_range() is replaced with udelay().
These bugs are found by my static analysis tool DSAC.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1ad61b612b ]
If _OSC execution fails today for platforms without an _OSC entry, code is
printing a misleading message saying disabling ASPM as follows:
acpi PNP0A03:00: _OSC failed (AE_NOT_FOUND); disabling ASPM
We need to ensure that platform supports ASPM to begin with.
Reported-by: Michael Kelley <mikelley@microsoft.com>
Signed-off-by: Sinan Kaya <okaya@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b7a417628a ]
The driver registers the v4l2 subdevice before attempting to power on the
chip and checking its ID. This means that a media device driver that it's
waiting for this subdevice to be bound, will prematurely expose its media
device node to userspace because if something goes wrong the media entity
will be cleaned up again on the ov2680 probe function.
This also simplifies the probe function error path since no initialization
is made before attempting to enable the resources or checking the chip ID.
Fixes: 3ee47cad3e ("media: ov2680: Add Omnivision OV2680 sensor driver")
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4d19db777a ]
Calling napi_schedule() from process context does not ensure that the
NET_RX softirq is run in a timely fashion. So trigger it manually.
This is no big issue with current code. A call to ndo_open() is usually
followed by a ndo_set_rx_mode() call, and for qeth this contains a
spin_unlock_bh(). Except for OSN, where qeth_l2_set_rx_mode() bails out
early.
Nevertheless it's best to not depend on this behaviour, and just fix
the issue at its source like all other drivers do. For instance see
commit 83a0c6e589 ("i40e: Invoke softirqs after napi_reschedule").
Fixes: a1c3ed4c9c ("qeth: NAPI support for l2 and l3 discipline")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 121ca39aa5 ]
When setting up, qeth installs its IRQ handler on the ccw devices. But
the IRQ handler is not cleared on removal - so even after qeth yields
control of the ccw devices, spurious interrupts would still be presented
to us.
Make (de-)installation of the IRQ handler part of the ccw channel
setup/removal helpers, and while at it also add the appropriate locking.
Shift around qeth_setup_channel() to avoid a forward declaration for
qeth_irq().
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 461cf03605 ]
We tried to revert commit d9c52fd17c ("ath9k: fix tx99 with monitor
mode interface") but accidentally missed part of the locking change.
The lock has to be held earlier so that we're holding it when we do
"sc->tx99_vif = vif;" and also there in the current code there is a
stray unlock before we have taken the lock.
Fixes: 6df0580be8 ("ath9k: add back support for using active monitor interfaces for tx99")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fa5950e498 ]
None of these spots really needs to crash the kernel.
In one two cases we can jsut report error to userspace, in the other
cases we can just use WARN_ON (and leak memory instead).
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 86b62e5cd8 ]
lpss_iosf_enter_d3_state() checks if all hw-blocks using the DMA
controllers are in d3 before powering down the DMA controllers.
But on devices, where the I2C bus connected to the PMIC is shared by
the PUNIT, the controller for that bus will never reach d3 since it has
an effectively empty _PS3 method. Instead it appears to automatically
power-down during S0i3 and we never see it as being in d3.
This causes the DMA controllers to never be powered-down on these devices,
causing them to never reach S0i3. This commit uses the ACPI _SEM method
to detect if an I2C bus is shared with the PUNIT and if it is, it removes
it from the mask of devices which lpss_iosf_enter_d3_state() checks for.
This fixes these devices never reaching any S0ix states.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 501500e65f ]
dtc has new checks for I2C buses. Fix the warnings in unit-addresses.
arch/arm64/boot/dts/rockchip/rk3399-puma-haikou.dtb: Warning (i2c_bus_reg): /i2c@ff3d0000/codec@0a: I2C bus unit address format error, expected "a"
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: linux-rockchip@lists.infradead.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 131c3eb428 ]
dtc has new checks for SPI buses. The rk3036 dts file has a node named
spi' which causes false positive warnings. As the node is a pinctrl child
node, change the node name to be 'spi-pins' to fix the warnings.
arch/arm/boot/dts/rk3036-evb.dtb: Warning (spi_bus_bridge): /pinctrl/spi: incorrect #address-cells for SPI bus
arch/arm/boot/dts/rk3036-kylin.dtb: Warning (spi_bus_bridge): /pinctrl/spi: incorrect #address-cells for SPI bus
arch/arm/boot/dts/rk3036-evb.dtb: Warning (spi_bus_bridge): /pinctrl/spi: incorrect #size-cells for SPI bus
arch/arm/boot/dts/rk3036-kylin.dtb: Warning (spi_bus_bridge): /pinctrl/spi: incorrect #size-cells for SPI bus
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: linux-rockchip@lists.infradead.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit eebcc19646 ]
Error paths in ufshcd_init() ufshcd_hba_exit() killed clk_scaling workqueue
when the workqueue is actually created quite late in ufshcd_init(). So, we
end up getting NULL pointer dereference in such error paths. Fix this by
moving clk_scaling initialization and kill codes to two separate methods, and
call them at required places.
Fixes: 401f1e4490 ("scsi: ufs: don't suspend clock scaling during clock
gating")
Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Subhash Jadavani <subhashj@codeaurora.org>
Cc: Matthias Kaehlcke <mka@chromium.org>
Cc: Evan Green <evgreen@chromium.org>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b0350d51f0 ]
gre_parse_header stops parsing when csum_err is encountered, which means
tpi->key is undefined and ip_tunnel_lookup will return NULL improperly.
This patch introduce a NULL pointer as csum_err parameter. Even when
csum_err is encountered, it won't return error and continue parsing gre
header as expected.
Fixes: 9f57c67c37 ("gre: Remove support for sharing GRE protocol hook.")
Reported-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a75e78f21f ]
The terminating NUL byte is only there because the buffer is
allocated with kzalloc(PAGE_SIZE, GFP_KERNEL), but since the
range-check is off-by-one, and PAGE_SIZE==PATH_MAX, the
returned string may not be zero-terminated if it is exactly
PATH_MAX characters long. Furthermore also the initial loop
may theoretically exceed PATH_MAX and cause a fault.
Signed-off-by: Bernd Edlinger <bernd.edlinger@hotmail.de>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bdae566d5d ]
During component_bind_all(), if bind() fails for any
particular component associated with a master, unbind()
should be called for all previous components in that
master's match array, whose bind() might have completed
successfully. As per the current logic, if bind() fails
for the component at position 'n' in the master's match
array, it would start calling unbind() from component in
'n'th position itself and work backwards, and will always
skip calling unbind() for component in 0th position in the
master's match array.
Fix this by updating the loop condition, and the logic to
refer to the components in master's match array, so that
unbind() is called for all components starting from 'n-1'st
position in the array, until (and including) component in
0th position.
Signed-off-by: Banajit Goswami <bgoswami@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cb90a2c6f7 ]
Since the max8998 MFD driver supports instantiation by DT, platform data
retrieval is handled in MFD probe and cell drivers should get use
the pdata field of max8998_dev struct to obtain them.
Fixes: ee999fb3f1 ("mfd: max8998: Add support for Device Tree")
Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
