[ Upstream commit 419013740e ]
ep93xx_clocksource_read() is only called from the file it is declared in,
while ep93xx_timer_init() is declared in a header that is not included here.
arch/arm/mach-ep93xx/timer-ep93xx.c:120:13: error: no previous prototype for 'ep93xx_timer_init'
arch/arm/mach-ep93xx/timer-ep93xx.c:63:5: error: no previous prototype for 'ep93xx_clocksource_read'
Fixes: 000bc17817 ("ARM: ep93xx: switch to GENERIC_CLOCKEVENTS")
Acked-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Link: https://lore.kernel.org/r/20230516153109.514251-3-arnd@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f24b495508 ]
The previous setting was related to the overall dimension and not to the
active display area.
In the "PHYSICAL SPECIFICATIONS" section, the datasheet shows the
following parameters:
----------------------------------------------------------
| Item | Specifications | unit |
----------------------------------------------------------
| Display area | 98.7 (W) x 57.5 (H) | mm |
----------------------------------------------------------
| Overall dimension | 105.5(W) x 67.2(H) x 4.96(D) | mm |
----------------------------------------------------------
Fixes: 966fea78ad ("drm/panel: simple: Add support for Ampire AM-480272H3TMQW-T01H")
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
[narmstrong: fixed Fixes commit id length]
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230516085039.3797303-1-dario.binacchi@amarulasolutions.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dd9e329af7 ]
The datasheet describes the following initialization flow including
minimum delay times between each step:
1. DSI data lanes need to be in LP-11 and the clock lane in HS mode
2. toggle EN signal
3. initialize registers
4. enable PLL
5. soft reset
6. enable DSI stream
7. check error status register
To meet this requirement we need to make sure the host bridge's
pre_enable() is called first by using the pre_enable_prev_first
flag.
Furthermore we need to split enable() into pre_enable() which covers
steps 2-5 from above and enable() which covers step 7 and is called
after the host bridge's enable().
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Fixes: ceb515ba29 ("drm/bridge: ti-sn65dsi83: Add TI SN65DSI83 and SN65DSI84 driver")
Tested-by: Alexander Stein <alexander.stein@ew.tq-group.com> #TQMa8MxML/MBa8Mx
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230503163313.2640898-3-frieder@fris.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4fb912e5e1 ]
DSI sink devices typically want the DSI host powered up and configured
before they are powered up. pre_enable is the place this would normally
happen, but they are called in reverse order from panel/connector towards
the encoder, which is the "wrong" order.
Add a new flag pre_enable_prev_first that any bridge can set
to swap the order of pre_enable (and post_disable) for that and the
immediately previous bridge.
Should the immediately previous bridge also set the
pre_enable_prev_first flag, the previous bridge to that will be called
before either of those which requested pre_enable_prev_first.
eg:
- Panel
- Bridge 1
- Bridge 2 pre_enable_prev_first
- Bridge 3
- Bridge 4 pre_enable_prev_first
- Bridge 5 pre_enable_prev_first
- Bridge 6
- Encoder
Would result in pre_enable's being called as Panel, Bridge 1, Bridge 3,
Bridge 2, Bridge 6, Bridge 5, Bridge 4, Encoder.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Tested-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Link: https://lore.kernel.org/r/20221205173328.1395350-5-dave.stevenson@raspberrypi.com
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Stable-dep-of: dd9e329af7 ("drm/bridge: ti-sn65dsi83: Fix enable/disable flow to meet spec")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5500f823db ]
The 96Boards specification expects a 1.8V power rail on the low-speed
expansion connector that is able to provide at least 0.18W / 100 mA.
According to the DB410c hardware user manual this is done by connecting
both L15 and L16 in parallel with up to 55mA each (for 110 mA total) [1].
Unfortunately the current regulator setup in the DB410c device tree
does not implement the specification correctly and only provides 5 mA:
- Only L15 is marked always-on, so L16 is never enabled.
- Without specifying a load the regulator is put into LPM where
it can only provide 5 mA.
Fix this by:
- Adding proper voltage constraints for L16.
- Making L16 always-on.
- Adding regulator-system-load for both L15 and L16. 100 mA should be
available in total, so specify 50 mA for each. (The regulator
hardware can only be in normal (55 mA) or low-power mode (5 mA) so
this will actually result in the expected 110 mA total...)
[1]: https://www.96boards.org/documentation/consumer/dragonboard/dragonboard410c/hardware-docs/hardware-user-manual.md.html#power-supplies
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Fixes: 828dd5d66f ("arm64: dts: apq8016-sbc: make 1.8v available on LS expansion")
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230510-msm8916-regulators-v1-2-54d4960a05fc@gerhold.net
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e27654df20 ]
For some reason DB410c has completely bogus regulator constraints that
actually just correspond to the programmable voltages which are already
provided by the regulator driver. Some of them are not just outside the
recommended operating conditions of the APQ8016E SoC but even exceed
the absolute maximum ratings, potentially risking permanent device
damage.
In practice it's not quite as dangerous thanks to the RPM firmware:
It turns out that it has its own voltage constraints and silently
clamps all regulator requests. For example, requesting 3.3V for L5
(allowed by the current regulator constraints!) still results in 1.8V
being programmed in the actual regulator hardware.
Experimentation with various voltages shows that the internal RPM
voltage constraints roughly correspond to the safe "specified range"
in the PM8916 Device Specification (rather than the "programmable
range" used inside apq8016-sbc.dtsi right now).
Combine those together with some fixed voltages used in the old
msm-3.10 device tree from Qualcomm to give DB410c some actually valid
voltage constraints.
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Fixes: 4c7d53d16d ("arm64: dts: apq8016-sbc: add regulators support")
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230510-msm8916-regulators-v1-1-54d4960a05fc@gerhold.net
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1464e48d69 ]
During probe, the driver registers i2c dummy devices and populates the
aux bus, which registers a device for the panel. After doing that, the
driver can still defer probe if needed. This ordering of operations is
troublesome however, because the deferred probe work will retry probing
all pending devices every time a new device is registered. Therefore, if
modules need to be loaded in order to satisfy the dependencies for this
driver to complete probe, the kernel will stall, since it'll keep trying
to probe the anx7625 driver, but never succeed, given that modules would
only be loaded after the deferred probe work completes.
Two changes are required to avoid this issue:
* Move of_find_mipi_dsi_host_by_node(), which can defer probe, to before
anx7625_register_i2c_dummy_clients() and
devm_of_dp_aux_populate_ep_devices(), which register devices.
* Make use of the done_probing callback when populating the aux bus,
so that the bridge registration is only done after the panel is
probed. This is required because the panel might need to defer probe,
but the aux bus population needs the i2c dummy devices working, so
this call couldn't just be moved to an earlier point in probe.
One caveat is that if the panel is described outside the aux bus, the
probe loop issue can still happen, but we don't have a way to avoid
it in that case since there's no callback available.
With this patch applied, it's possible to boot on
mt8192-asurada-spherion with
CONFIG_DRM_ANALOGIX_ANX7625=y
CONFIG_MTK_MMSYS=m
CONFIG_BACKLIGHT_PWM=y
and also with
CONFIG_DRM_ANALOGIX_ANX7625=y
CONFIG_MTK_MMSYS=y
CONFIG_BACKLIGHT_PWM=m
Fixes: adca62ec37 ("drm/bridge: anx7625: Support reading edid through aux channel")
Fixes: 269332997a ("drm/bridge: anx7625: Return -EPROBE_DEFER if the dsi host was not found")
Reported-by: "kernelci.org bot" <bot@kernelci.org>
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230518193902.891121-1-nfraprado@collabora.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4ffec92e70 ]
The model property should be at the top level, let's move it out
of the pinctrl node.
Fixes: d2eaf949d2 ("ARM: dts: omap3-gta04a5one: define GTA04A5 variant with OneNAND")
Cc: Andreas Kemnade <andreas@kemnade.info>
Cc: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7061b6af34 ]
When map() is called on a detached domain, the domain does not exist in
the device so we do not send a MAP request, but we do update the
internal mapping tree, to be replayed on the next attach. Since this
constitutes a successful iommu_map() call, return *mapped in this case
too.
Fixes: 7e62edd7a3 ("iommu/virtio: Add map/unmap_pages() callbacks implementation")
Signed-off-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com>
Link: https://lore.kernel.org/r/20230515113946.1017624-3-jean-philippe@linaro.org
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ff2e4bfd16 ]
bnxt_re currently uses the names "bnxt_qplib_creq" and "bnxt_qplib_nq-0"
while registering IRQs. There is no way to distinguish the IRQs of
different device ports when there are multiple IB devices registered.
This could make the scenarios worse where one want to pin IRQs of a device
port to certain CPUs.
Fixed the code to use unique names which has PCI BDF information while
registering interrupts like: "bnxt_re-nq-0@pci:0000:65:00.0" and
"bnxt_re-creq@pci:0000:65:00.1".
Fixes: 1ac5a40479 ("RDMA/bnxt_re: Add bnxt_re RoCE driver")
Link: https://lore.kernel.org/r/1684478897-12247-4-git-send-email-selvin.xavier@broadcom.com
Reviewed-by: Bhargava Chenna Marreddy <bhargava.marreddy@broadcom.com>
Signed-off-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ab112ee789 ]
When the ulp hook to start the IRQ fails because the rings are not
available, tasklets are not enabled. In this case when the driver is
unloaded, driver calls CREQ tasklet_kill. This causes an indefinite hang
as the tasklet is not enabled.
Driver shouldn't call tasklet_kill if it is not enabled. So using the
creq->requested and nq->requested flags to identify if both tasklets/irqs
are registered. Checking this flag while scheduling the tasklet from
ISR. Also, added a cleanup for disabling tasklet, in case request_irq
fails during start_irq.
Check for return value for bnxt_qplib_rcfw_start_irq and in case the
bnxt_qplib_rcfw_start_irq fails, return bnxt_re_start_irq without
attempting to start NQ IRQs.
Fixes: 1ac5a40479 ("RDMA/bnxt_re: Add bnxt_re RoCE driver")
Link: https://lore.kernel.org/r/1684478897-12247-2-git-send-email-selvin.xavier@broadcom.com
Signed-off-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0babf89c9c ]
In the unlikely event that something goes wrong with the device and
its registers, the fan_from_reg() function may return 0. This value
will cause a division-by-zero error in the show_pwm() function.
To prevent this, test the value of
fan_from_reg(data->fan_full_speed[nr]) against 0 before performing
the division. If the division-by-zero error is avoided, assign 0 to
the val variable.
Found by Linux Verification Center (linuxtesting.org) with static
analysis tool SVACE.
Fixes: df9ec2dae0 ("hwmon: (f71882fg) Reorder symbols to get rid of a few forward declarations")
Signed-off-by: Nikita Zhandarovich <n.zhandarovich@fintech.ru>
Link: https://lore.kernel.org/r/20230510143537.145060-1-n.zhandarovich@fintech.ru
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 70be83708c ]
PSCI is not implemented on SparX-5 at all, there is no ATF and U-boot that
is shipped does not implement it as well.
I have tried flashing the latest BSP 2022.12 U-boot which did not work.
After contacting Microchip, they confirmed that there is no ATF for the
SoC nor PSCI implementation which is unfortunate in 2023.
So, disable PSCI as otherwise kernel crashes as soon as it tries probing
PSCI with, and the crash is only visible if earlycon is used.
Since PSCI is not implemented, switch core bringup to use spin-tables
which are implemented in the vendor U-boot and actually work.
Tested on PCB134 with eMMC (VSC5640EV).
Fixes: 6694aee00a ("arm64: dts: sparx5: Add basic cpu support")
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Acked-by: Steen Hegelund <Steen.Hegelund@microchip.com>
Link: https://lore.kernel.org/r/20230221105039.316819-1-robert.marko@sartura.hr
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9660efc2af ]
The ethernet MAC EEPROM is not populated on the SoM itself, it has to be
populated on each carrier board. Move the EEPROM into the correct place
in DTs, i.e. the carrier board DTs. Add label to the EEPROM too.
Fixes: 7e76f82acd ("ARM: dts: stm32: Split Avenger96 into DHCOR SoM and Avenger96 board")
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ab87f558dc ]
Currently, the pixel conversion isn't rounding the fixed-point values
before assigning it to the RGB coefficients, which is causing the IGT
pixel-format tests to fail. So, use the drm_fixp2int_round() fixed-point
helper to round the values when assigning it to the RGB coefficients.
Tested with igt@kms_plane@pixel-format and igt@kms_plane@pixel-format-source-clamping.
[v2]:
* Use drm_fixp2int_round() to fix the pixel conversion instead of
casting the values to s32 (Melissa Wen).
Fixes: 89b03aeaef ("drm/vkms: fix 32bit compilation error by replacing macros")
Signed-off-by: Maíra Canal <mcanal@igalia.com>
Reviewed-by: Arthur Grillo <arthurgrillo@riseup.net>
Signed-off-by: Maíra Canal <mairacanal@riseup.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20230512104044.65034-2-mcanal@igalia.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 123ee07ba5 ]
Smatch reports:
drivers/gpu/drm/sun4i/sun4i_tcon.c:805 sun4i_tcon_init_clocks() warn:
'tcon->clk' from clk_prepare_enable() not released on lines: 792,801.
In the function sun4i_tcon_init_clocks(), tcon->clk and tcon->sclk0 are
not disabled in the error handling, which affects the release of
these variable. Although sun4i_tcon_bind(), which calls
sun4i_tcon_init_clocks(), use sun4i_tcon_free_clocks to disable the
variables mentioned, but the error handling branch of
sun4i_tcon_init_clocks() ignores the required disable process.
To fix this issue, use the devm_clk_get_enabled to automatically
balance enable and disabled calls. As original implementation use
sun4i_tcon_free_clocks() to disable clk explicitly, we delete the
related calls and error handling that are no longer needed.
Fixes: 9026e0d122 ("drm: Add Allwinner A10 Display Engine support")
Fixes: b14e945bda ("drm/sun4i: tcon: Prepare and enable TCON channel 0 clock at init")
Fixes: 8e92404725 ("drm/sun4i: support TCONs without channel 1")
Fixes: 34d698f6e3 ("drm/sun4i: Add has_channel_0 TCON quirk")
Signed-off-by: XuDong Liu <m202071377@hust.edu.cn>
Reviewed-by: Dongliang Mu <dzm91@hust.edu.cn>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20230430112347.4689-1-m202071377@hust.edu.cn
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ad527ca87e ]
The .driver_data content in i2c_device_id table must match the
.data content in of_device_id table, else device_get_match_data()
would return bogus value on i2c_device_id match. Align the two
tables.
The i2c_device_id table is now converted from of_device_id using
's@.compatible = "renesas,\([^"]\+"\), .data = \(.*\)@"\1, .driver_data = (kernel_ulong_t)\2@'
Fixes: 892e0ddea1 ("clk: rs9: Add Renesas 9-series PCIe clock generator driver")
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Link: https://lore.kernel.org/r/20230507133906.15061-3-marek.vasut+renesas@mailbox.org
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b5e10beeaf ]
The .driver_data content in i2c_device_id table must match the
.data content in of_device_id table, else device_get_match_data()
would return bogus value on i2c_device_id match. Align the two
tables.
The i2c_device_id table is now converted from of_device_id using
's@.compatible = "renesas,\([^"]\+"\), .data = \(.*\)@"\1, .driver_data = (kernel_ulong_t)\2@'
Fixes: 48c5e98fed ("clk: Renesas versaclock7 ccf device driver")
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Link: https://lore.kernel.org/r/20230507133906.15061-2-marek.vasut+renesas@mailbox.org
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
