[ Upstream commit 7b0454cfd8edb3509619407c3b9f78a6d0dee1a5 ]
As the sensor device maybe accessible right after its async sub-device is
registered, such as ipu-bridge will try to power up sensor by sensor's
client device's runtime PM from the async notifier callback, if runtime PM
is not enabled, it will fail.
So runtime PM should be ready before its async sub-device is registered
and accessible by others.
Fixes: 7ee8505468 ("media: Add sensor driver support for the ov13b10 camera.")
Cc: stable@vger.kernel.org
Signed-off-by: Bingbu Cao <bingbu.cao@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1af2f618ac ]
Tell ACPI device PM code that the driver supports the device being in
non-zero ACPI D state when the driver's probe function is entered.
Also do identification on the first access of the device, whether in
probe or when starting streaming.
Signed-off-by: Arec Kao <arec.kao@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Stable-dep-of: 7b0454cfd8ed ("media: ov13b10: Enable runtime PM before registering async sub-device")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3c12466b6b7bf1e56f9b32c366a3d83d87afb4de ]
Currently EROFS can map another compressed buffer for inplace
decompression, that was used to handle the cases that some pages of
compressed data are actually not in-place I/O.
However, like most simple LZ77 algorithms, LZ4 expects the compressed
data is arranged at the end of the decompressed buffer and it
explicitly uses memmove() to handle overlapping:
__________________________________________________________
|_ direction of decompression --> ____ |_ compressed data _|
Although EROFS arranges compressed data like this, it typically maps two
individual virtual buffers so the relative order is uncertain.
Previously, it was hardly observed since LZ4 only uses memmove() for
short overlapped literals and x86/arm64 memmove implementations seem to
completely cover it up and they don't have this issue. Juhyung reported
that EROFS data corruption can be found on a new Intel x86 processor.
After some analysis, it seems that recent x86 processors with the new
FSRM feature expose this issue with "rep movsb".
Let's strictly use the decompressed buffer for lz4 inplace
decompression for now. Later, as an useful improvement, we could try
to tie up these two buffers together in the correct order.
Reported-and-tested-by: Juhyung Park <qkrwngud825@gmail.com>
Closes: https://lore.kernel.org/r/CAD14+f2AVKf8Fa2OO1aAUdDNTDsVzzR6ctU_oJSmTyd6zSYR2Q@mail.gmail.com
Fixes: 0ffd71bcc3 ("staging: erofs: introduce LZ4 decompression inplace")
Fixes: 598162d050 ("erofs: support decompress big pcluster for lz4 backend")
Cc: stable <stable@vger.kernel.org> # 5.4+
Tested-by: Yifan Zhao <zhaoyifan@sjtu.edu.cn>
Signed-off-by: Gao Xiang <hsiangkao@linux.alibaba.com>
Link: https://lore.kernel.org/r/20231206045534.3920847-1-hsiangkao@linux.alibaba.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit ca1ffb174f16b699c536734fc12a4162097c49f4 upstream.
The power source flag should be updated when
[1] System receives an interrupt indicating that the power source
has changed.
[2] System resumes from suspend or runtime suspend
Signed-off-by: Ma Jun <Jun.Ma2@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 28d3d0696688154cc04983f343011d07bf0508e4 upstream.
The i2c_master_send/recv() functions return negative error codes or
they return "len" on success. So the error handling here can be written
as just normal checks for "if (ret < 0) return ret;". No need to
complicate things.
Btw, in this code the "len" parameter can never be zero, but even if
it were, then I feel like this would still be the best way to write it.
Fixes: 914437992876 ("drm/bridge: nxp-ptn3460: fix i2c_master_send() error checking")
Suggested-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/04242630-42d8-4920-8c67-24ac9db6b3c9@moroto.mountain
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 416de0246f35f43d871a57939671fe814f4455ee upstream.
When booting a kernel with CONFIG_CFI_CLANG, there is a CFI failure when
accessing any of the values under
/sys/devices/system/cpu/intel_uncore_frequency/package_00_die_00:
$ cat /sys/devices/system/cpu/intel_uncore_frequency/package_00_die_00/max_freq_khz
fish: Job 1, 'cat /sys/devices/system/cpu/int…' terminated by signal SIGSEGV (Address boundary error)
$ sudo dmesg &| grep 'CFI failure'
[ 170.953925] CFI failure at kobj_attr_show+0x19/0x30 (target: show_max_freq_khz+0x0/0xc0 [intel_uncore_frequency_common]; expected type: 0xd34078c5
The sysfs callback functions such as show_domain_id() are written as if
they are going to be called by dev_attr_show() but as the above message
shows, they are instead called by kobj_attr_show(). kCFI checks that the
destination of an indirect jump has the exact same type as the prototype
of the function pointer it is called through and fails when they do not.
These callbacks are called through kobj_attr_show() because
uncore_root_kobj was initialized with kobject_create_and_add(), which
means uncore_root_kobj has a ->sysfs_ops of kobj_sysfs_ops from
kobject_create(), which uses kobj_attr_show() as its ->show() value.
The only reason there has not been a more noticeable problem until this
point is that 'struct kobj_attribute' and 'struct device_attribute' have
the same layout, so getting the callback from container_of() works the
same with either value.
Change all the callbacks and their uses to be compatible with
kobj_attr_show() and kobj_attr_store(), which resolves the kCFI failure
and allows the sysfs files to work properly.
Closes: https://github.com/ClangBuiltLinux/linux/issues/1974
Fixes: ae7b2ce578 ("platform/x86/intel/uncore-freq: Use sysfs API to create attributes")
Cc: stable@vger.kernel.org
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Sami Tolvanen <samitolvanen@google.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Link: https://lore.kernel.org/r/20240104-intel-uncore-freq-kcfi-fix-v1-1-bf1e8939af40@kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
[nathan: Fix conflicts due to lack of 9b8dea80e3 in 6.1]
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 95d4b471953411854f9c80b568da7fcf753f3801 upstream.
tidss_crtc_atomic_flush() checks if the crtc is enabled, and if not,
returns immediately as there's no reason to do any register changes.
However, the code checks for 'crtc->state->enable', which does not
reflect the actual HW state. We should instead look at the
'crtc->state->active' flag.
This causes the tidss_crtc_atomic_flush() to proceed with the flush even
if the active state is false, which then causes us to hit the
WARN_ON(!crtc->state->event) check.
Fix this by checking the active flag, and while at it, fix the related
debug print which had "active" and "needs modeset" wrong way.
Cc: <stable@vger.kernel.org>
Fixes: 32a1795f57 ("drm/tidss: New driver for TI Keystone platform Display SubSystem")
Reviewed-by: Aradhya Bhatia <a-bhatia1@ti.com>
Link: https://lore.kernel.org/r/20231109-tidss-probe-v2-10-ac91b5ea35c0@ideasonboard.com
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cb4daf271302d71a6b9a7c01bd0b6d76febd8f0c upstream.
If we get a deadlock after the fb lookup in drm_mode_page_flip_ioctl()
we proceed to unref the fb and then retry the whole thing from the top.
But we forget to reset the fb pointer back to NULL, and so if we then
get another error during the retry, before the fb lookup, we proceed
the unref the same fb again without having gotten another reference.
The end result is that the fb will (eventually) end up being freed
while it's still in use.
Reset fb to NULL once we've unreffed it to avoid doing it again
until we've done another fb lookup.
This turned out to be pretty easy to hit on a DG2 when doing async
flips (and CONFIG_DEBUG_WW_MUTEX_SLOWPATH=y). The first symptom I
saw that drm_closefb() simply got stuck in a busy loop while walking
the framebuffer list. Fortunately I was able to convince it to oops
instead, and from there it was easier to track down the culprit.
Cc: stable@vger.kernel.org
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231211081625.25704-1-ville.syrjala@linux.intel.com
Acked-by: Javier Martinez Canillas <javierm@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 192cdb1c907fd8df2d764c5bb17496e415e59391 upstream.
On systems using HWP, if a given frequency is equal to the maximum turbo
frequency or the maximum non-turbo frequency, the HWP performance level
corresponding to it is already known and can be used directly without
any computation.
Accordingly, adjust the code to use the known HWP performance levels in
the cases mentioned above.
This also helps to avoid limiting CPU capacity artificially in some
cases when the BIOS produces the HWP_CAP numbers using a different
E-core-to-P-core performance scaling factor than expected by the kernel.
Fixes: f5c8cf2a49 ("cpufreq: intel_pstate: hybrid: Use known scaling factor for P-cores")
Cc: 6.1+ <stable@vger.kernel.org> # 6.1+
Tested-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d8d222e09dab84a17bb65dda4b94d01c565f5327 upstream.
Recently xfs/513 started failing on my test machines testing "-o
ro,norecovery" mount options. This was being emitted in dmesg:
[ 9906.932724] XFS (pmem0): no-recovery mounts must be read-only.
Turns out, readonly mounts with the fsopen()/fsconfig() mount API
have been busted since day zero. It's only taken 5 years for debian
unstable to start using this "new" mount API, and shortly after this
I noticed xfs/513 had started to fail as per above.
The syscall trace is:
fsopen("xfs", FSOPEN_CLOEXEC) = 3
mount_setattr(-1, NULL, 0, NULL, 0) = -1 EINVAL (Invalid argument)
.....
fsconfig(3, FSCONFIG_SET_STRING, "source", "/dev/pmem0", 0) = 0
fsconfig(3, FSCONFIG_SET_FLAG, "ro", NULL, 0) = 0
fsconfig(3, FSCONFIG_SET_FLAG, "norecovery", NULL, 0) = 0
fsconfig(3, FSCONFIG_CMD_CREATE, NULL, NULL, 0) = -1 EINVAL (Invalid argument)
close(3) = 0
Showing that the actual mount instantiation (FSCONFIG_CMD_CREATE) is
what threw out the error.
During mount instantiation, we call xfs_fs_validate_params() which
does:
/* No recovery flag requires a read-only mount */
if (xfs_has_norecovery(mp) && !xfs_is_readonly(mp)) {
xfs_warn(mp, "no-recovery mounts must be read-only.");
return -EINVAL;
}
and xfs_is_readonly() checks internal mount flags for read only
state. This state is set in xfs_init_fs_context() from the
context superblock flag state:
/*
* Copy binary VFS mount flags we are interested in.
*/
if (fc->sb_flags & SB_RDONLY)
set_bit(XFS_OPSTATE_READONLY, &mp->m_opstate);
With the old mount API, all of the VFS specific superblock flags
had already been parsed and set before xfs_init_fs_context() is
called, so this all works fine.
However, in the brave new fsopen/fsconfig world,
xfs_init_fs_context() is called from fsopen() context, before any
VFS superblock have been set or parsed. Hence if we use fsopen(),
the internal XFS readonly state is *never set*. Hence anything that
depends on xfs_is_readonly() actually returning true for read only
mounts is broken if fsopen() has been used to mount the filesystem.
Fix this by moving this internal state initialisation to
xfs_fs_fill_super() before we attempt to validate the parameters
that have been set prior to the FSCONFIG_CMD_CREATE call being made.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Fixes: 73e5fff98b ("xfs: switch to use the new mount-api")
cc: stable@vger.kernel.org
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Chandan Babu R <chandanbabu@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 437a310b22244d4e0b78665c3042e5d1c0f45306 upstream.
On reception of a completion interrupt the shared memory area is accessed
to retrieve the message header at first and then, if the message sequence
number identifies a transaction which is still pending, the related
payload is fetched too.
When an SCMI command times out the channel ownership remains with the
platform until eventually a late reply is received and, as a consequence,
any further transmission attempt remains pending, waiting for the channel
to be relinquished by the platform.
Once that late reply is received the channel ownership is given back
to the agent and any pending request is then allowed to proceed and
overwrite the SMT area of the just delivered late reply; then the wait
for the reply to the new request starts.
It has been observed that the spurious IRQ related to the late reply can
be wrongly associated with the freshly enqueued request: when that happens
the SCMI stack in-flight lookup procedure is fooled by the fact that the
message header now present in the SMT area is related to the new pending
transaction, even though the real reply has still to arrive.
This race-condition on the A2P channel can be detected by looking at the
channel status bits: a genuine reply from the platform will have set the
channel free bit before triggering the completion IRQ.
Add a consistency check to validate such condition in the A2P ISR.
Reported-by: Xinglong Yang <xinglong.yang@cixtech.com>
Closes: https://lore.kernel.org/all/PUZPR06MB54981E6FA00D82BFDBB864FBF08DA@PUZPR06MB5498.apcprd06.prod.outlook.com/
Fixes: 5c8a47a5a9 ("firmware: arm_scmi: Make scmi core independent of the transport type")
Cc: stable@vger.kernel.org # 5.15+
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Tested-by: Xinglong Yang <xinglong.yang@cixtech.com>
Link: https://lore.kernel.org/r/20231220172112.763539-1-cristian.marussi@arm.com
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5913320eb0b3ec88158cfcb0fa5e996bf4ef681b upstream.
p2sb_bar() unhides P2SB device to get resources from the device. It
guards the operation by locking pci_rescan_remove_lock so that parallel
rescans do not find the P2SB device. However, this lock causes deadlock
when PCI bus rescan is triggered by /sys/bus/pci/rescan. The rescan
locks pci_rescan_remove_lock and probes PCI devices. When PCI devices
call p2sb_bar() during probe, it locks pci_rescan_remove_lock again.
Hence the deadlock.
To avoid the deadlock, do not lock pci_rescan_remove_lock in p2sb_bar().
Instead, do the lock at fs_initcall. Introduce p2sb_cache_resources()
for fs_initcall which gets and caches the P2SB resources. At p2sb_bar(),
refer the cache and return to the caller.
Before operating the device at P2SB DEVFN for resource cache, check
that its device class is PCI_CLASS_MEMORY_OTHER 0x0580 that PCH
specifications define. This avoids unexpected operation to other devices
at the same DEVFN.
Link: https://lore.kernel.org/linux-pci/6xb24fjmptxxn5js2fjrrddjae6twex5bjaftwqsuawuqqqydx@7cl3uik5ef6j/
Fixes: 9745fb0747 ("platform/x86/intel: Add Primary to Sideband (P2SB) bridge support")
Cc: stable@vger.kernel.org
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Shin'ichiro Kawasaki <shinichiro.kawasaki@wdc.com>
Link: https://lore.kernel.org/r/20240108062059.3583028-2-shinichiro.kawasaki@wdc.com
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Tested-by Klara Modin <klarasmodin@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f342de4e2f33e0e39165d8639387aa6c19dff660 upstream.
This reverts commit e0abdadcc6.
core.c:nf_hook_slow assumes that the upper 16 bits of NF_DROP
verdicts contain a valid errno, i.e. -EPERM, -EHOSTUNREACH or similar,
or 0.
Due to the reverted commit, its possible to provide a positive
value, e.g. NF_ACCEPT (1), which results in use-after-free.
Its not clear to me why this commit was made.
NF_QUEUE is not used by nftables; "queue" rules in nftables
will result in use of "nft_queue" expression.
If we later need to allow specifiying errno values from userspace
(do not know why), this has to call NF_DROP_GETERR and check that
"err <= 0" holds true.
Fixes: e0abdadcc6 ("netfilter: nf_tables: accept QUEUE/DROP verdict parameters")
Cc: stable@vger.kernel.org
Reported-by: Notselwyn <notselwyn@pwning.tech>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 01acb2e8666a6529697141a6017edbf206921913 upstream.
Remove netdevice from inet/ingress basechain in case NETDEV_UNREGISTER
event is reported, otherwise a stale reference to netdevice remains in
the hook list.
Fixes: 60a3815da7 ("netfilter: add inet ingress support")
Cc: stable@vger.kernel.org
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6941f67ad37d5465b75b9ffc498fcf6897a3c00e upstream.
Current code in netvsc_drv_init() incorrectly assumes that PAGE_SIZE
is 4 Kbytes, which is wrong on ARM64 with 16K or 64K page size. As a
result, the default VMBus ring buffer size on ARM64 with 64K page size
is 8 Mbytes instead of the expected 512 Kbytes. While this doesn't break
anything, a typical VM with 8 vCPUs and 8 netvsc channels wastes 120
Mbytes (8 channels * 2 ring buffers/channel * 7.5 Mbytes/ring buffer).
Unfortunately, the module parameter specifying the ring buffer size
is in units of 4 Kbyte pages. Ideally, it should be in units that
are independent of PAGE_SIZE, but backwards compatibility prevents
changing that now.
Fix this by having netvsc_drv_init() hardcode 4096 instead of using
PAGE_SIZE when calculating the ring buffer size in bytes. Also
use the VMBUS_RING_SIZE macro to ensure proper alignment when running
with page size larger than 4K.
Cc: <stable@vger.kernel.org> # 5.15.x
Fixes: 7aff79e297 ("Drivers: hv: Enable Hyper-V code to be built on ARM64")
Signed-off-by: Michael Kelley <mhklinux@outlook.com>
Link: https://lore.kernel.org/r/20240122162028.348885-1-mhklinux@outlook.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ded080c86b3f99683774af0441a58fc2e3d60cae upstream.
The running list is supposed to contain requests that are pinning the
exclusive lock, i.e. those that must be flushed before exclusive lock
is released. When wake_lock_waiters() is called to handle an error,
requests on the acquiring list are failed with that error and no
flushing takes place. Briefly moving them to the running list is not
only pointless but also harmful: if exclusive lock gets acquired
before all of their state machines are scheduled and go through
rbd_lock_del_request(), we trigger
rbd_assert(list_empty(&rbd_dev->running_list));
in rbd_try_acquire_lock().
Cc: stable@vger.kernel.org
Fixes: 637cd06053 ("rbd: new exclusive lock wait/wake code")
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Dongsheng Yang <dongsheng.yang@easystack.cn>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 173431b274a9a54fc10b273b46e67f46bcf62d2e upstream.
Add extra sanity check for btrfs_ioctl_defrag_range_args::flags.
This is not really to enhance fuzzing tests, but as a preparation for
future expansion on btrfs_ioctl_defrag_range_args.
In the future we're going to add new members, allowing more fine tuning
for btrfs defrag. Without the -ENONOTSUPP error, there would be no way
to detect if the kernel supports those new defrag features.
CC: stable@vger.kernel.org # 4.14+
Reviewed-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a208b3f132b48e1f94f620024e66fea635925877 upstream.
There's a warning in btrfs_issue_discard() when the range is not aligned
to 512 bytes, originally added in 4d89d377bb ("btrfs:
btrfs_issue_discard ensure offset/length are aligned to sector
boundaries"). We can't do sub-sector writes anyway so the adjustment is
the only thing that we can do and the warning is unnecessary.
CC: stable@vger.kernel.org # 4.19+
Reported-by: syzbot+4a4f1eba14eb5c3417d1@syzkaller.appspotmail.com
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3324d0547861b16cf436d54abba7052e0c8aa9de upstream.
Sweet Tea spotted a race between subvolume deletion and snapshotting
that can result in the root item for the snapshot having the
BTRFS_ROOT_SUBVOL_DEAD flag set. The race is:
Thread 1 | Thread 2
----------------------------------------------|----------
btrfs_delete_subvolume |
btrfs_set_root_flags(BTRFS_ROOT_SUBVOL_DEAD)|
|btrfs_mksubvol
| down_read(subvol_sem)
| create_snapshot
| ...
| create_pending_snapshot
| copy root item from source
down_write(subvol_sem) |
This flag is only checked in send and swap activate, which this would
cause to fail mysteriously.
create_snapshot() now checks the root refs to reject a deleted
subvolume, so we can fix this by locking subvol_sem earlier so that the
BTRFS_ROOT_SUBVOL_DEAD flag and the root refs are updated atomically.
CC: stable@vger.kernel.org # 4.14+
Reported-by: Sweet Tea Dorminy <sweettea-kernel@dorminy.me>
Reviewed-by: Sweet Tea Dorminy <sweettea-kernel@dorminy.me>
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: Omar Sandoval <osandov@fb.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5e344807735023cd3a67c37a1852b849caa42620 ]
When repeatedly changing the interface link speed using the command below:
ethtool -s eth0 speed 100 duplex full
ethtool -s eth0 speed 1000 duplex full
The following errors may sometimes be reported by the ARM SMMU driver:
[ 5395.035364] fec 5b040000.ethernet eth0: Link is Down
[ 5395.039255] arm-smmu 51400000.iommu: Unhandled context fault:
fsr=0x402, iova=0x00000000, fsynr=0x100001, cbfrsynra=0x852, cb=2
[ 5398.108460] fec 5b040000.ethernet eth0: Link is Up - 100Mbps/Full -
flow control off
It is identified that the FEC driver does not properly stop the TX queue
during the link speed transitions, and this results in the invalid virtual
I/O address translations from the SMMU and causes the context faults.
Fixes: dbc64a8ea2 ("net: fec: move calls to quiesce/resume packet processing out of fec_restart()")
Signed-off-by: Shenwei Wang <shenwei.wang@nxp.com>
Link: https://lore.kernel.org/r/20240123165141.2008104-1-shenwei.wang@nxp.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f6cc4b6a3ae53df425771000e9c9540cce9b7bb1 ]
In fjes_hw_setup, it allocates several memory and delay the deallocation
to the fjes_hw_exit in fjes_probe through the following call chain:
fjes_probe
|-> fjes_hw_init
|-> fjes_hw_setup
|-> fjes_hw_exit
However, when fjes_hw_setup fails, fjes_hw_exit won't be called and thus
all the resources allocated in fjes_hw_setup will be leaked. In this
patch, we free those resources in fjes_hw_setup and prevents such leaks.
Fixes: 2fcbca6877 ("fjes: platform_driver's .probe and .remove routine")
Signed-off-by: Zhipeng Lu <alexious@zju.edu.cn>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240122172445.3841883-1-alexious@zju.edu.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a5f5eee282a0aae80227697e1d9c811b1726d31d ]
otherwise the synopsys_id value may be read out wrong,
because the GMAC_VERSION register might still be in reset
state, for at least 1 us after the reset is de-asserted.
Add a wait for 10 us before continuing to be on the safe side.
> From what have you got that delay value?
Just try and error, with very old linux versions and old gcc versions
the synopsys_id was read out correctly most of the time (but not always),
with recent linux versions and recnet gcc versions it was read out
wrongly most of the time, but again not always.
I don't have access to the VHDL code in question, so I cannot
tell why it takes so long to get the correct values, I also do not
have more than a few hardware samples, so I cannot tell how long
this timeout must be in worst case.
Experimentally I can tell that the register is read several times
as zero immediately after the reset is de-asserted, also adding several
no-ops is not enough, adding a printk is enough, also udelay(1) seems to
be enough but I tried that not very often, and I have not access to many
hardware samples to be 100% sure about the necessary delay.
And since the udelay here is only executed once per device instance,
it seems acceptable to delay the boot for 10 us.
BTW: my hardware's synopsys id is 0x37.
Fixes: c5e4ddbdfa ("net: stmmac: Add support for optional reset control")
Signed-off-by: Bernd Edlinger <bernd.edlinger@hotmail.de>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Link: https://lore.kernel.org/r/AS8P193MB1285A810BD78C111E7F6AA34E4752@AS8P193MB1285.EURP193.PROD.OUTLOOK.COM
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b462579b2b86a8f5230543cadd3a4836be27baf7 ]
nftables has two types of sets/maps, one where userspace defines the
name, and anonymous sets/maps, where userspace defines a template name.
For the latter, kernel requires presence of exactly one "%d".
nftables uses "__set%d" and "__map%d" for this. The kernel will
expand the format specifier and replaces it with the smallest unused
number.
As-is, userspace could define a template name that allows to move
the set name past the 256 bytes upperlimit (post-expansion).
I don't see how this could be a problem, but I would prefer if userspace
cannot do this, so add a limit of 16 bytes for the '%d' template name.
16 bytes is the old total upper limit for set names that existed when
nf_tables was merged initially.
Fixes: 387454901b ("netfilter: nf_tables: Allow set names of up to 255 chars")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 8e7f82deb0 upstream.
When opening a directory (opendir(3)) or rewinding it (rewinddir(3)), we
are not holding the directory's inode locked, and this can result in later
attempting to add two entries to the directory with the same index number,
resulting in a transaction abort, with -EEXIST (-17), when inserting the
second delayed dir index. This results in a trace like the following:
Sep 11 22:34:59 myhostname kernel: BTRFS error (device dm-3): err add delayed dir index item(name: cockroach-stderr.log) into the insertion tree of the delayed node(root id: 5, inode id: 4539217, errno: -17)
Sep 11 22:34:59 myhostname kernel: ------------[ cut here ]------------
Sep 11 22:34:59 myhostname kernel: kernel BUG at fs/btrfs/delayed-inode.c:1504!
Sep 11 22:34:59 myhostname kernel: invalid opcode: 0000 [#1] PREEMPT SMP NOPTI
Sep 11 22:34:59 myhostname kernel: CPU: 0 PID: 7159 Comm: cockroach Not tainted 6.4.15-200.fc38.x86_64 #1
Sep 11 22:34:59 myhostname kernel: Hardware name: ASUS ESC500 G3/P9D WS, BIOS 2402 06/27/2018
Sep 11 22:34:59 myhostname kernel: RIP: 0010:btrfs_insert_delayed_dir_index+0x1da/0x260
Sep 11 22:34:59 myhostname kernel: Code: eb dd 48 (...)
Sep 11 22:34:59 myhostname kernel: RSP: 0000:ffffa9980e0fbb28 EFLAGS: 00010282
Sep 11 22:34:59 myhostname kernel: RAX: 0000000000000000 RBX: ffff8b10b8f4a3c0 RCX: 0000000000000000
Sep 11 22:34:59 myhostname kernel: RDX: 0000000000000000 RSI: ffff8b177ec21540 RDI: ffff8b177ec21540
Sep 11 22:34:59 myhostname kernel: RBP: ffff8b110cf80888 R08: 0000000000000000 R09: ffffa9980e0fb938
Sep 11 22:34:59 myhostname kernel: R10: 0000000000000003 R11: ffffffff86146508 R12: 0000000000000014
Sep 11 22:34:59 myhostname kernel: R13: ffff8b1131ae5b40 R14: ffff8b10b8f4a418 R15: 00000000ffffffef
Sep 11 22:34:59 myhostname kernel: FS: 00007fb14a7fe6c0(0000) GS:ffff8b177ec00000(0000) knlGS:0000000000000000
Sep 11 22:34:59 myhostname kernel: CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
Sep 11 22:34:59 myhostname kernel: CR2: 000000c00143d000 CR3: 00000001b3b4e002 CR4: 00000000001706f0
Sep 11 22:34:59 myhostname kernel: Call Trace:
Sep 11 22:34:59 myhostname kernel: <TASK>
Sep 11 22:34:59 myhostname kernel: ? die+0x36/0x90
Sep 11 22:34:59 myhostname kernel: ? do_trap+0xda/0x100
Sep 11 22:34:59 myhostname kernel: ? btrfs_insert_delayed_dir_index+0x1da/0x260
Sep 11 22:34:59 myhostname kernel: ? do_error_trap+0x6a/0x90
Sep 11 22:34:59 myhostname kernel: ? btrfs_insert_delayed_dir_index+0x1da/0x260
Sep 11 22:34:59 myhostname kernel: ? exc_invalid_op+0x50/0x70
Sep 11 22:34:59 myhostname kernel: ? btrfs_insert_delayed_dir_index+0x1da/0x260
Sep 11 22:34:59 myhostname kernel: ? asm_exc_invalid_op+0x1a/0x20
Sep 11 22:34:59 myhostname kernel: ? btrfs_insert_delayed_dir_index+0x1da/0x260
Sep 11 22:34:59 myhostname kernel: ? btrfs_insert_delayed_dir_index+0x1da/0x260
Sep 11 22:34:59 myhostname kernel: btrfs_insert_dir_item+0x200/0x280
Sep 11 22:34:59 myhostname kernel: btrfs_add_link+0xab/0x4f0
Sep 11 22:34:59 myhostname kernel: ? ktime_get_real_ts64+0x47/0xe0
Sep 11 22:34:59 myhostname kernel: btrfs_create_new_inode+0x7cd/0xa80
Sep 11 22:34:59 myhostname kernel: btrfs_symlink+0x190/0x4d0
Sep 11 22:34:59 myhostname kernel: ? schedule+0x5e/0xd0
Sep 11 22:34:59 myhostname kernel: ? __d_lookup+0x7e/0xc0
Sep 11 22:34:59 myhostname kernel: vfs_symlink+0x148/0x1e0
Sep 11 22:34:59 myhostname kernel: do_symlinkat+0x130/0x140
Sep 11 22:34:59 myhostname kernel: __x64_sys_symlinkat+0x3d/0x50
Sep 11 22:34:59 myhostname kernel: do_syscall_64+0x5d/0x90
Sep 11 22:34:59 myhostname kernel: ? syscall_exit_to_user_mode+0x2b/0x40
Sep 11 22:34:59 myhostname kernel: ? do_syscall_64+0x6c/0x90
Sep 11 22:34:59 myhostname kernel: entry_SYSCALL_64_after_hwframe+0x72/0xdc
The race leading to the problem happens like this:
1) Directory inode X is loaded into memory, its ->index_cnt field is
initialized to (u64)-1 (at btrfs_alloc_inode());
2) Task A is adding a new file to directory X, holding its vfs inode lock,
and calls btrfs_set_inode_index() to get an index number for the entry.
Because the inode's index_cnt field is set to (u64)-1 it calls
btrfs_inode_delayed_dir_index_count() which fails because no dir index
entries were added yet to the delayed inode and then it calls
btrfs_set_inode_index_count(). This functions finds the last dir index
key and then sets index_cnt to that index value + 1. It found that the
last index key has an offset of 100. However before it assigns a value
of 101 to index_cnt...
3) Task B calls opendir(3), ending up at btrfs_opendir(), where the VFS
lock for inode X is not taken, so it calls btrfs_get_dir_last_index()
and sees index_cnt still with a value of (u64)-1. Because of that it
calls btrfs_inode_delayed_dir_index_count() which fails since no dir
index entries were added to the delayed inode yet, and then it also
calls btrfs_set_inode_index_count(). This also finds that the last
index key has an offset of 100, and before it assigns the value 101
to the index_cnt field of inode X...
4) Task A assigns a value of 101 to index_cnt. And then the code flow
goes to btrfs_set_inode_index() where it increments index_cnt from
101 to 102. Task A then creates a delayed dir index entry with a
sequence number of 101 and adds it to the delayed inode;
5) Task B assigns 101 to the index_cnt field of inode X;
6) At some later point when someone tries to add a new entry to the
directory, btrfs_set_inode_index() will return 101 again and shortly
after an attempt to add another delayed dir index key with index
number 101 will fail with -EEXIST resulting in a transaction abort.
Fix this by locking the inode at btrfs_get_dir_last_index(), which is only
only used when opening a directory or attempting to lseek on it.
Reported-by: ken <ken@bllue.org>
Link: https://lore.kernel.org/linux-btrfs/CAE6xmH+Lp=Q=E61bU+v9eWX8gYfLvu6jLYxjxjFpo3zHVPR0EQ@mail.gmail.com/
Reported-by: syzbot+d13490c82ad5353c779d@syzkaller.appspotmail.com
Link: https://lore.kernel.org/linux-btrfs/00000000000036e1290603e097e0@google.com/
Fixes: 9b378f6ad4 ("btrfs: fix infinite directory reads")
CC: stable@vger.kernel.org # 6.5+
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e60aa5da14 upstream.
When opening a directory we find what's the index of its last entry and
then store it in the directory's file handle private data (struct
btrfs_file_private::last_index), so that in the case new directory entries
are added to a directory after an opendir(3) call we don't end up in an
infinite loop (see commit 9b378f6ad4 ("btrfs: fix infinite directory
reads")) when calling readdir(3).
However once rewinddir(3) is called, POSIX states [1] that any new
directory entries added after the previous opendir(3) call, must be
returned by subsequent calls to readdir(3):
"The rewinddir() function shall reset the position of the directory
stream to which dirp refers to the beginning of the directory.
It shall also cause the directory stream to refer to the current
state of the corresponding directory, as a call to opendir() would
have done."
We currently don't refresh the last_index field of the struct
btrfs_file_private associated to the directory, so after a rewinddir(3)
we are not returning any new entries added after the opendir(3) call.
Fix this by finding the current last index of the directory when llseek
is called against the directory.
This can be reproduced by the following C program provided by Ian Johnson:
#include <dirent.h>
#include <stdio.h>
int main(void) {
DIR *dir = opendir("test");
FILE *file;
file = fopen("test/1", "w");
fwrite("1", 1, 1, file);
fclose(file);
file = fopen("test/2", "w");
fwrite("2", 1, 1, file);
fclose(file);
rewinddir(dir);
struct dirent *entry;
while ((entry = readdir(dir))) {
printf("%s\n", entry->d_name);
}
closedir(dir);
return 0;
}
Reported-by: Ian Johnson <ian@ianjohnson.dev>
Link: https://lore.kernel.org/linux-btrfs/YR1P0S.NGASEG570GJ8@ianjohnson.dev/
Fixes: 9b378f6ad4 ("btrfs: fix infinite directory reads")
CC: stable@vger.kernel.org # 6.5+
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 357950361c upstream.
When opening a directory for reading it, we set the last index where we
stop iteration to the value in struct btrfs_inode::index_cnt. That value
does not match the index of the most recently added directory entry but
it's instead the index number that will be assigned the next directory
entry.
This means that if after the call to opendir(3) new directory entries are
added, a readdir(3) call will return the first new directory entry. This
is fine because POSIX says the following [1]:
"If a file is removed from or added to the directory after the most
recent call to opendir() or rewinddir(), whether a subsequent call to
readdir() returns an entry for that file is unspecified."
For example for the test script from commit 9b378f6ad4 ("btrfs: fix
infinite directory reads"), where we have 2000 files in a directory, ext4
doesn't return any new directory entry after opendir(3), while xfs returns
the first 13 new directory entries added after the opendir(3) call.
If we move to a shorter example with an empty directory when opendir(3) is
called, and 2 files added to the directory after the opendir(3) call, then
readdir(3) on btrfs will return the first file, ext4 and xfs return the 2
files (but in a different order). A test program for this, reported by
Ian Johnson, is the following:
#include <dirent.h>
#include <stdio.h>
int main(void) {
DIR *dir = opendir("test");
FILE *file;
file = fopen("test/1", "w");
fwrite("1", 1, 1, file);
fclose(file);
file = fopen("test/2", "w");
fwrite("2", 1, 1, file);
fclose(file);
struct dirent *entry;
while ((entry = readdir(dir))) {
printf("%s\n", entry->d_name);
}
closedir(dir);
return 0;
}
To make this less odd, change the behaviour to never return new entries
that were added after the opendir(3) call. This is done by setting the
last_index field of the struct btrfs_file_private attached to the
directory's file handle with a value matching btrfs_inode::index_cnt
minus 1, since that value always matches the index of the next new
directory entry and not the index of the most recently added entry.
[1] https://pubs.opengroup.org/onlinepubs/007904875/functions/readdir_r.html
Link: https://lore.kernel.org/linux-btrfs/YR1P0S.NGASEG570GJ8@ianjohnson.dev/
CC: stable@vger.kernel.org # 6.5+
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9b378f6ad4 upstream.
The readdir implementation currently processes always up to the last index
it finds. This however can result in an infinite loop if the directory has
a large number of entries such that they won't all fit in the given buffer
passed to the readdir callback, that is, dir_emit() returns a non-zero
value. Because in that case readdir() will be called again and if in the
meanwhile new directory entries were added and we still can't put all the
remaining entries in the buffer, we keep repeating this over and over.
The following C program and test script reproduce the problem:
$ cat /mnt/readdir_prog.c
#include <sys/types.h>
#include <dirent.h>
#include <stdio.h>
int main(int argc, char *argv[])
{
DIR *dir = opendir(".");
struct dirent *dd;
while ((dd = readdir(dir))) {
printf("%s\n", dd->d_name);
rename(dd->d_name, "TEMPFILE");
rename("TEMPFILE", dd->d_name);
}
closedir(dir);
}
$ gcc -o /mnt/readdir_prog /mnt/readdir_prog.c
$ cat test.sh
#!/bin/bash
DEV=/dev/sdi
MNT=/mnt/sdi
mkfs.btrfs -f $DEV &> /dev/null
#mkfs.xfs -f $DEV &> /dev/null
#mkfs.ext4 -F $DEV &> /dev/null
mount $DEV $MNT
mkdir $MNT/testdir
for ((i = 1; i <= 2000; i++)); do
echo -n > $MNT/testdir/file_$i
done
cd $MNT/testdir
/mnt/readdir_prog
cd /mnt
umount $MNT
This behaviour is surprising to applications and it's unlike ext4, xfs,
tmpfs, vfat and other filesystems, which always finish. In this case where
new entries were added due to renames, some file names may be reported
more than once, but this varies according to each filesystem - for example
ext4 never reported the same file more than once while xfs reports the
first 13 file names twice.
So change our readdir implementation to track the last index number when
opendir() is called and then make readdir() never process beyond that
index number. This gives the same behaviour as ext4.
Reported-by: Rob Landley <rob@landley.net>
Link: https://lore.kernel.org/linux-btrfs/2c8c55ec-04c6-e0dc-9c5c-8c7924778c35@landley.net/
Link: https://bugzilla.kernel.org/show_bug.cgi?id=217681
CC: stable@vger.kernel.org # 5.15
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c9d9eb9c53d37cdebbad56b91e40baf42d5a97aa ]
Reject bogus configs where internal token counter wraps around.
This only occurs with very very large requests, such as 17gbyte/s.
Its better to reject this rather than having incorrect ratelimit.
Fixes: d2168e849e ("netfilter: nft_limit: add per-byte limiting")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e787644caf7628ad3269c1fbd321c3255cf51710 ]
When the CPU goes idle for the last time during the CPU down hotplug
process, RCU reports a final quiescent state for the current CPU. If
this quiescent state propagates up to the top, some tasks may then be
woken up to complete the grace period: the main grace period kthread
and/or the expedited main workqueue (or kworker).
If those kthreads have a SCHED_FIFO policy, the wake up can indirectly
arm the RT bandwith timer to the local offline CPU. Since this happens
after hrtimers have been migrated at CPUHP_AP_HRTIMERS_DYING stage, the
timer gets ignored. Therefore if the RCU kthreads are waiting for RT
bandwidth to be available, they may never be actually scheduled.
This triggers TREE03 rcutorture hangs:
rcu: INFO: rcu_preempt self-detected stall on CPU
rcu: 4-...!: (1 GPs behind) idle=9874/1/0x4000000000000000 softirq=0/0 fqs=20 rcuc=21071 jiffies(starved)
rcu: (t=21035 jiffies g=938281 q=40787 ncpus=6)
rcu: rcu_preempt kthread starved for 20964 jiffies! g938281 f0x0 RCU_GP_WAIT_FQS(5) ->state=0x0 ->cpu=0
rcu: Unless rcu_preempt kthread gets sufficient CPU time, OOM is now expected behavior.
rcu: RCU grace-period kthread stack dump:
task:rcu_preempt state:R running task stack:14896 pid:14 tgid:14 ppid:2 flags:0x00004000
Call Trace:
<TASK>
__schedule+0x2eb/0xa80
schedule+0x1f/0x90
schedule_timeout+0x163/0x270
? __pfx_process_timeout+0x10/0x10
rcu_gp_fqs_loop+0x37c/0x5b0
? __pfx_rcu_gp_kthread+0x10/0x10
rcu_gp_kthread+0x17c/0x200
kthread+0xde/0x110
? __pfx_kthread+0x10/0x10
ret_from_fork+0x2b/0x40
? __pfx_kthread+0x10/0x10
ret_from_fork_asm+0x1b/0x30
</TASK>
The situation can't be solved with just unpinning the timer. The hrtimer
infrastructure and the nohz heuristics involved in finding the best
remote target for an unpinned timer would then also need to handle
enqueues from an offline CPU in the most horrendous way.
So fix this on the RCU side instead and defer the wake up to an online
CPU if it's too late for the local one.
Reported-by: Paul E. McKenney <paulmck@kernel.org>
Fixes: 5c0930ccaad5 ("hrtimers: Push pending hrtimers away from outgoing CPU earlier")
Signed-off-by: Frederic Weisbecker <frederic@kernel.org>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Neeraj Upadhyay (AMD) <neeraj.iitr10@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit aef855df7e1bbd5aa4484851561211500b22707e ]
When kcalloc() for ft->g succeeds but kvzalloc() for in fails,
fs_any_create_groups() will free ft->g. However, its caller
fs_any_create_table() will free ft->g again through calling
mlx5e_destroy_flow_table(), which will lead to a double-free.
Fix this by setting ft->g to NULL in fs_any_create_groups().
Fixes: 0f575c20bf ("net/mlx5e: Introduce Flow Steering ANY API")
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3c6d5189246f590e4e1f167991558bdb72a4738b ]
When `in` allocated by kvzalloc fails, arfs_create_groups will free
ft->g and return an error. However, arfs_create_table, the only caller of
arfs_create_groups, will hold this error and call to
mlx5e_destroy_flow_table, in which the ft->g will be freed again.
Fixes: 1cabe6b096 ("net/mlx5e: Create aRFS flow tables")
Signed-off-by: Zhipeng Lu <alexious@zju.edu.cn>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 20f5468a7988dedd94a57ba8acd65ebda6a59723 ]
All ConnectX devices have software parsing capability enabled, but it is
more correct to set allow_swp only if capability exists, which for IPsec
means that crypto offload is supported.
Fixes: 2451da081a ("net/mlx5: Unify device IPsec capabilities check")
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 20cbf8cbb827094197f3b17db60d71449415db1e ]
mlx5 devices have specific constants for choosing the CQ period mode. These
constants do not have to match the constants used by the kernel software
API for DIM period mode selection.
Fixes: cdd04f4d4d ("net/mlx5: Add support to create SQ and CQ for ASO")
Signed-off-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Reviewed-by: Jianbo Liu <jianbol@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5b2a2523eeea5f03d39a9d1ff1bad2e9f8eb98d2 ]
Go-To-Vport action on RX is not allowed when the vport is uplink.
In such case, the packet should be dropped.
Fixes: 9db810ed2d ("net/mlx5: DR, Expose steering action functionality")
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Reviewed-by: Erez Shitrit <erezsh@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
