[ Upstream commit e23ad54fef186aa66007895be1382c88f1ee2bf7 ]
The Lunnen Ground 15 and 16 needs IRQ overriding for the keyboard to
work.
Adding an entries for these laptops to the override_table makes the
internal keyboard functional.
Signed-off-by: Alexey I. Froloff <raorn@raorn.name>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Stable-dep-of: 021a67d09615 ("ACPI: resource: Add MAIBENBEN X577 to irq1_edge_low_force_override")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 79978bff2e4b8e05ebdf5fc3ee6b794002393484 ]
We identified that the PHYs actually do not work since commit 7da7b84fee
("ARM: dts: imx6dl-yapp4: Move phy reset into switch node") as
a coincidence of several circumstances.
The reset signal is kept asserted by a pull-down resistor on the board
unless it is deasserted by GPIO from the SoC. This is to keep the switch
dead until it is configured properly by the kernel and user space.
Prior to the referenced commit the switch was reset by the FEC driver
and the reset GPIO was actively deasserted. The mdio-bus was scanned
and the attached switch and its PHYs were found and configured.
With the referenced commit the switch is reset by the qca8k driver.
Because of another bug in the qca8k driver, functionality of the reset
pin depends on its pre-kernel configuration. See commit c44fc98f0a8f
("net: dsa: qca8k: fix illegal usage of GPIO")
The problem did not appear until we removed support for the switch
and configuration of its reset pin from the bootloader.
To fix that, properly describe the internal mdio-bus configuration of
the qca8334 switch. The PHYs are internal to the switch and sit on its
internal mdio-bus.
Fixes: 7da7b84fee ("ARM: dts: imx6dl-yapp4: Move phy reset into switch node")
Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 023bd910d3ab735459f84b22bb99fb9e00bd9d76 ]
This change does not have any functional effect. The switch works just
fine without this patch as it has full access to all the addresses
on the bus. This is simply a clean-up to set the node name address
and reg address to the same value.
Fixes: 15b43e497f ("ARM: dts: imx6dl-yapp4: Use correct pseudo PHY address for the switch")
Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7da7b84fee ]
Drop the phy-reset-duration and phy-reset-gpios deprecated properties and
move reset-gpios under the switch node.
Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Stable-dep-of: 023bd910d3ab ("ARM: dts: imx6dl-yapp4: Fix typo in the QCA switch register address")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7b59348c11f3355e284d77bbe3d33632ddadcfc2 ]
The SPDIF hardware found on the H6 supports both transmit and receive
functions. However it is missing the RX DMA channel.
Add the SPDIF hardware block's RX DMA channel. Also remove the
by-default pinmux, since the end device can choose to implement
either or both functionalities.
Fixes: f95b598df4 ("arm64: dts: allwinner: Add SPDIF node for Allwinner H6")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20240127163247.384439-6-wens@kernel.org
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a43e0fc5e9134a46515de2f2f8d4100b74e50de3 ]
Unloading a modular pstore backend with records in pstorefs would
trigger the dput() double-drop warning:
WARNING: CPU: 0 PID: 2569 at fs/dcache.c:762 dput.part.0+0x3f3/0x410
Using the combo of d_drop()/dput() (as mentioned in
Documentation/filesystems/vfs.rst) isn't the right approach here, and
leads to the reference counting problem seen above. Use d_invalidate()
and update the code to not bother checking for error codes that can
never happen.
Suggested-by: Alexander Viro <viro@zeniv.linux.org.uk>
Fixes: 609e28bb13 ("pstore: Remove filesystem records when backend is unregistered")
Signed-off-by: Kees Cook <keescook@chromium.org>
[ Upstream commit 1394c1dec1c619a46867ed32791a29695372bff8 ]
If we're fragmenting on local output, the original packet may contain
ext data for the MCTP flows. We'll want this in the resulting fragment
skbs too.
So, do a skb_ext_copy() in the fragmentation path, and implement the
MCTP-specific parts of an ext copy operation.
Fixes: 67737c4572 ("mctp: Pass flow data & flow release events to drivers")
Reported-by: Jian Zhang <zhangjian.3032@bytedance.com>
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b9a0be2054 ]
Move RZ/G2UL SoC specific parts to r9a07g043u.dtsi so that
r9a07g043.dtsi can be shared with RZ/Five (RISC-V SoC).
Below are the changes due to which SoC specific parts are moved to
r9a07g043u.dtsi:
- RZ/G2UL has Cortex-A55 (ARM64) whereas RZ/Five has AX45MP (RISC-V),
- RZ/G2UL has GICv3 as interrupt controller whereas RZ/Five has PLIC,
- RZ/G2UL has interrupts for SYSC block whereas interrupts are missing
for SYSC block on RZ/Five,
- RZ/G2UL has armv8-timer whereas RZ/Five has riscv-timer,
- RZ/G2UL has PSCI whereas RZ/Five have OpenSBI.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20221025220629.79321-3-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Stable-dep-of: 14fe225dd5fc ("arm64: dts: renesas: rzg2l: Add missing interrupts to IRQC nodes")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3baa4c5143d65ebab2de0d99a395e5f4f1f46608 ]
When the development chip ROM was added, the "direct-mapped" compatible
value was already obsolete. In addition, the device node lacked the
accompanying "probe-type" property, causing the old physmap_of_core
driver to fall back to trying all available probe types.
Unfortunately this fallback was lost when the DT and pdata cases were
merged.
Fix this by using the modern "mtd-rom" compatible value instead.
Fixes: 5c3f5edbe0 ("ARM: realview: add flash devices to the PB1176 DTS")
Fixes: 642b1e8dbe ("mtd: maps: Merge physmap_of.c into physmap-core.c")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f3ec643947634bed41b97bd56b248f7c78498eab ]
This reverts commit fcf690b0b4.
When using a wilc1000 chip over a spi bus, users can optionally define a
reset gpio and a chip enable gpio. The reset line of wilc1000 is active
low, so to hold the chip in reset, a low (physical) value must be applied.
The corresponding device tree binding documentation was introduced by
commit f31ee3c0a5 ("wilc1000: Document enable-gpios and reset-gpios
properties") and correctly indicates that the reset line is an active-low
signal. The corresponding driver part, brought by commit ec031ac479
("wilc1000: Add reset/enable GPIO support to SPI driver") was applying the
correct logic. But commit fcf690b0b4 ("wifi: wilc1000: use correct
sequence of RESET for chip Power-UP/Down") eventually flipped this logic
and started misusing the gpiod APIs, applying an inverted logic when
powering up/down the chip (for example, setting the reset line to a logic
"1" during power up, which in fact asserts the reset line when device tree
describes the reset line as GPIO_ACTIVE_LOW). As a consequence, any
platform currently using the driver in SPI mode must use a faulty reset
line description in device tree, or else chip will be maintained in reset
and will not even allow to bring up the chip.
Fix reset line usage by inverting back the gpiod APIs usage, setting the
reset line to the logic value "0" when powering the chip, and the logic
value "1" when powering off the chip.
Fixes: fcf690b0b4 ("wifi: wilc1000: use correct sequence of RESET for chip Power-UP/Down")
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Acked-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240217-wilc_1000_reset_line-v2-1-b216f433d7d5@bootlin.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 78e886ba2b549945ecada055ee0765f0ded5707a ]
Avoid the following warnings by removing the ena_select_queue() function
and rely on the net core to do the queue selection, The issue happen
when an skb received from an interface with more queues than ena is
forwarded to the ena interface.
[ 1176.159959] eth0 selects TX queue 11, but real number of TX queues is 8
[ 1176.863976] eth0 selects TX queue 14, but real number of TX queues is 8
[ 1180.767877] eth0 selects TX queue 14, but real number of TX queues is 8
[ 1188.703742] eth0 selects TX queue 14, but real number of TX queues is 8
Fixes: 1738cd3ed3 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)")
Signed-off-by: Kamal Heib <kheib@redhat.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b50155cb0d609437236c88201206267835c6f965 ]
The caller of the function freq_qos_add_request() checks again a non
zero value but freq_qos_add_request() can return '1' if the request
already exists. Therefore, the setup function fails while the QoS
request actually did not failed.
Fix that by changing the check against a negative value like all the
other callers of the function.
Fixes: 0e8f68d7f0 ("Add CPU energy model based support")
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e1ea6db35fc3ba5ff063f097385e9f7a88c25356 ]
An old cleanup went a little too far and causes a warning with clang-16
and higher as it breaks control flow integrity (KCFI) rules:
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy_shim.c:64:34: error: cast from 'void (*)(struct brcms_phy *)' to 'void (*)(void *)' converts to incompatible function type [-Werror,-Wcast-function-type-strict]
64 | brcms_init_timer(physhim->wl, (void (*)(void *))fn,
| ^~~~~~~~~~~~~~~~~~~~
Change this one instance back to passing a void pointer so it can be
used with the timer callback interface.
Fixes: d89a4c8060 ("staging: brcm80211: removed void * from softmac phy")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240213100548.457854-1-arnd@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0feda94c868d396fac3b3cb14089d2d989a07c72 ]
On many systems that have an AMD IOMMU the following sequence of
warnings is observed during bootup.
```
pci 0000:00:00.2 can't derive routing for PCI INT A
pci 0000:00:00.2: PCI INT A: not connected
```
This series of events happens because of the IOMMU initialization
sequence order and the lack of _PRT entries for the IOMMU.
During initialization the IOMMU driver first enables the PCI device
using pci_enable_device(). This will call acpi_pci_irq_enable()
which will check if the interrupt is declared in a PCI routing table
(_PRT) entry. According to the PCI spec [1] these routing entries
are only required under PCI root bridges:
The _PRT object is required under all PCI root bridges
The IOMMU is directly connected to the root complex, so there is no
parent bridge to look for a _PRT entry. The first warning is emitted
since no entry could be found in the hierarchy. The second warning is
then emitted because the interrupt hasn't yet been configured to any
value. The pin was configured in pci_read_irq() but the byte in
PCI_INTERRUPT_LINE return 0xff which means "Unknown".
After that sequence of events pci_enable_msi() is called and this
will allocate an interrupt.
That is both of these warnings are totally harmless because the IOMMU
uses MSI for interrupts. To avoid even trying to probe for a _PRT
entry mark the IOMMU as IRQ managed. This avoids both warnings.
Link: https://uefi.org/htmlspecs/ACPI_Spec_6_4_html/06_Device_Configuration/Device_Configuration.html?highlight=_prt#prt-pci-routing-table [1]
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Fixes: cffe0a2b5a ("x86, irq: Keep balance of IOAPIC pin reference count")
Reviewed-by: Vasant Hegde <vasant.hegde@amd.com>
Link: https://lore.kernel.org/r/20240122233400.1802-1-mario.limonciello@amd.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4acd21a45c1446277e2abaece97d7fa7c2e692a9 ]
Update the architecture dependency to be the generic Tegra
because the driver works on the four latest Tegra generations
not just Tegra210, if you build a kernel with a specific
ARCH_TEGRA_xxx_SOC option that excludes Tegra210 you don't get
this driver.
Fixes: 46a88534af ("bus: Add support for Tegra ACONNECT")
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Cc: Jon Hunter <jonathanh@nvidia.com>
Cc: Thierry Reding <treding@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cb5942b77c05d54310a0420cac12935e9b6aa21c ]
wilc_netdev_cleanup currently triggers a KASAN warning, which can be
observed on interface registration error path, or simply by
removing the module/unbinding device from driver:
echo spi0.1 > /sys/bus/spi/drivers/wilc1000_spi/unbind
==================================================================
BUG: KASAN: slab-use-after-free in wilc_netdev_cleanup+0x508/0x5cc
Read of size 4 at addr c54d1ce8 by task sh/86
CPU: 0 PID: 86 Comm: sh Not tainted 6.8.0-rc1+ #117
Hardware name: Atmel SAMA5
unwind_backtrace from show_stack+0x18/0x1c
show_stack from dump_stack_lvl+0x34/0x58
dump_stack_lvl from print_report+0x154/0x500
print_report from kasan_report+0xac/0xd8
kasan_report from wilc_netdev_cleanup+0x508/0x5cc
wilc_netdev_cleanup from wilc_bus_remove+0xc8/0xec
wilc_bus_remove from spi_remove+0x8c/0xac
spi_remove from device_release_driver_internal+0x434/0x5f8
device_release_driver_internal from unbind_store+0xbc/0x108
unbind_store from kernfs_fop_write_iter+0x398/0x584
kernfs_fop_write_iter from vfs_write+0x728/0xf88
vfs_write from ksys_write+0x110/0x1e4
ksys_write from ret_fast_syscall+0x0/0x1c
[...]
Allocated by task 1:
kasan_save_track+0x30/0x5c
__kasan_kmalloc+0x8c/0x94
__kmalloc_node+0x1cc/0x3e4
kvmalloc_node+0x48/0x180
alloc_netdev_mqs+0x68/0x11dc
alloc_etherdev_mqs+0x28/0x34
wilc_netdev_ifc_init+0x34/0x8ec
wilc_cfg80211_init+0x690/0x910
wilc_bus_probe+0xe0/0x4a0
spi_probe+0x158/0x1b0
really_probe+0x270/0xdf4
__driver_probe_device+0x1dc/0x580
driver_probe_device+0x60/0x140
__driver_attach+0x228/0x5d4
bus_for_each_dev+0x13c/0x1a8
bus_add_driver+0x2a0/0x608
driver_register+0x24c/0x578
do_one_initcall+0x180/0x310
kernel_init_freeable+0x424/0x484
kernel_init+0x20/0x148
ret_from_fork+0x14/0x28
Freed by task 86:
kasan_save_track+0x30/0x5c
kasan_save_free_info+0x38/0x58
__kasan_slab_free+0xe4/0x140
kfree+0xb0/0x238
device_release+0xc0/0x2a8
kobject_put+0x1d4/0x46c
netdev_run_todo+0x8fc/0x11d0
wilc_netdev_cleanup+0x1e4/0x5cc
wilc_bus_remove+0xc8/0xec
spi_remove+0x8c/0xac
device_release_driver_internal+0x434/0x5f8
unbind_store+0xbc/0x108
kernfs_fop_write_iter+0x398/0x584
vfs_write+0x728/0xf88
ksys_write+0x110/0x1e4
ret_fast_syscall+0x0/0x1c
[...]
David Mosberger-Tan initial investigation [1] showed that this
use-after-free is due to netdevice unregistration during vif list
traversal. When unregistering a net device, since the needs_free_netdev has
been set to true during registration, the netdevice object is also freed,
and as a consequence, the corresponding vif object too, since it is
attached to it as private netdevice data. The next occurrence of the loop
then tries to access freed vif pointer to the list to move forward in the
list.
Fix this use-after-free thanks to two mechanisms:
- navigate in the list with list_for_each_entry_safe, which allows to
safely modify the list as we go through each element. For each element,
remove it from the list with list_del_rcu
- make sure to wait for RCU grace period end after each vif removal to make
sure it is safe to free the corresponding vif too (through
unregister_netdev)
Since we are in a RCU "modifier" path (not a "reader" path), and because
such path is expected not to be concurrent to any other modifier (we are
using the vif_mutex lock), we do not need to use RCU list API, that's why
we can benefit from list_for_each_entry_safe.
[1] https://lore.kernel.org/linux-wireless/ab077dbe58b1ea5de0a3b2ca21f275a07af967d2.camel@egauge.net/
Fixes: 8399918f30 ("staging: wilc1000: use RCU list to maintain vif interfaces list")
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240212-wilc_rework_deinit-v1-1-9203ae56c27f@bootlin.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 724c4bf0e4bf81dba77736afb93964c986c3c123 ]
The qfprom actually is bigger than 0x1000, so adjust the reg.
Note that the non-ECC-corrected qfprom can be found at 0xfc4b8000
(-0x4000). The current reg points to the ECC-corrected qfprom block
which should have equivalent values at all offsets compared to the
non-corrected version.
[luca@z3ntu.xyz: extract to standalone patch and adjust for review
comments]
Fixes: c59ffb5193 ("arm: dts: msm8974: Add thermal zones, tsens and qfprom nodes")
Signed-off-by: Craig Tatlor <ctatlor97@gmail.com>
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240210-msm8974-qfprom-v3-1-26c424160334@z3ntu.xyz
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 178c54666f9c4d2f49f2ea661d0c11b52f0ed190 ]
Currently tracing is supposed not to allow for bpf_spin_{lock,unlock}()
helper calls. This is to prevent deadlock for the following cases:
- there is a prog (prog-A) calling bpf_spin_{lock,unlock}().
- there is a tracing program (prog-B), e.g., fentry, attached
to bpf_spin_lock() and/or bpf_spin_unlock().
- prog-B calls bpf_spin_{lock,unlock}().
For such a case, when prog-A calls bpf_spin_{lock,unlock}(),
a deadlock will happen.
The related source codes are below in kernel/bpf/helpers.c:
notrace BPF_CALL_1(bpf_spin_lock, struct bpf_spin_lock *, lock)
notrace BPF_CALL_1(bpf_spin_unlock, struct bpf_spin_lock *, lock)
notrace is supposed to prevent fentry prog from attaching to
bpf_spin_{lock,unlock}().
But actually this is not the case and fentry prog can successfully
attached to bpf_spin_lock(). Siddharth Chintamaneni reported
the issue in [1]. The following is the macro definition for
above BPF_CALL_1:
#define BPF_CALL_x(x, name, ...) \
static __always_inline \
u64 ____##name(__BPF_MAP(x, __BPF_DECL_ARGS, __BPF_V, __VA_ARGS__)); \
typedef u64 (*btf_##name)(__BPF_MAP(x, __BPF_DECL_ARGS, __BPF_V, __VA_ARGS__)); \
u64 name(__BPF_REG(x, __BPF_DECL_REGS, __BPF_N, __VA_ARGS__)); \
u64 name(__BPF_REG(x, __BPF_DECL_REGS, __BPF_N, __VA_ARGS__)) \
{ \
return ((btf_##name)____##name)(__BPF_MAP(x,__BPF_CAST,__BPF_N,__VA_ARGS__));\
} \
static __always_inline \
u64 ____##name(__BPF_MAP(x, __BPF_DECL_ARGS, __BPF_V, __VA_ARGS__))
#define BPF_CALL_1(name, ...) BPF_CALL_x(1, name, __VA_ARGS__)
The notrace attribute is actually applied to the static always_inline function
____bpf_spin_{lock,unlock}(). The actual callback function
bpf_spin_{lock,unlock}() is not marked with notrace, hence
allowing fentry prog to attach to two helpers, and this
may cause the above mentioned deadlock. Siddharth Chintamaneni
actually has a reproducer in [2].
To fix the issue, a new macro NOTRACE_BPF_CALL_1 is introduced which
will add notrace attribute to the original function instead of
the hidden always_inline function and this fixed the problem.
[1] https://lore.kernel.org/bpf/CAE5sdEigPnoGrzN8WU7Tx-h-iFuMZgW06qp0KHWtpvoXxf1OAQ@mail.gmail.com/
[2] https://lore.kernel.org/bpf/CAE5sdEg6yUc_Jz50AnUXEEUh6O73yQ1Z6NV2srJnef0ZrQkZew@mail.gmail.com/
Fixes: d83525ca62 ("bpf: introduce bpf_spin_lock")
Signed-off-by: Yonghong Song <yonghong.song@linux.dev>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Link: https://lore.kernel.org/bpf/20240207070102.335167-1-yonghong.song@linux.dev
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9b49cabe631b0a25aaf8fc2ba81b5b9ea6ff01b7 ]
The commit adding the ChromeOS EC to the Asurada Devicetree mistakenly
added a base detection node. While tablet mode detection is supported by
CrosEC and used by Hayato, it is done through the cros-ec-keyb driver.
The base detection node, which is handled by the hid-google-hammer
driver, also provides tablet mode detection but by checking base
attachment status on the CrosEC, which is not supported for Asurada.
Hence, remove the unused CrosEC base detection node for Asurada.
Fixes: eb188a2aaa ("arm64: dts: mediatek: asurada: Add ChromeOS EC")
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Link: https://lore.kernel.org/r/20240207-mt8192-asurada-cbas-remove-v1-1-04cb65951975@collabora.com
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 04bd6411f506357fd1faedc2b2156e7ef206aa9a ]
The cbas node is used to describe base detection functionality in the
ChromeOS EC, which is used for units that have a detachable keyboard and
thus rely on this functionality to switch between tablet and laptop
mode.
Despite the original commit having added the cbas node to the
mt8183-kukui.dtsi, not all machines that include it are detachables. In
fact all machines that include from mt8183-kukui-jacuzzi.dtsi are either
clamshells (ie normal laptops) or convertibles, meaning the keyboard can
be flipped but not detached. The detection for the keyboard getting
flipped is handled by the driver bound to the keyboard-controller node
in the EC.
Move the base detection node from the base kukui dtsi to the dtsis where
all machines are detachables, and thus actually make use of the node.
Fixes: 4fa8492d1e ("arm64: dts: mt8183: add cbas node under cros_ec")
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20240116-mt8183-kukui-cbas-remove-v3-1-055e21406e86@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 82492c4ef8 ]
Kukui devices krane, kodana, and kakadu use detachable keyboards, which
only have switches to be registered.
Change the keyboard node's compatible of those boards to the newly
introduced "google,cros-ec-keyb-switches", which won't include matrix
properties.
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Link: https://lore.kernel.org/r/20220527045353.2483042-1-hsinyi@chromium.org
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Stable-dep-of: 04bd6411f506 ("arm64: dts: mt8183: Move CrosEC base detection node to kukui-based DTs")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 17ef8efc00b34918b966388b2af0993811895a8c ]
As discussed in the past (commit 2d3916f318 ("ipv6: fix skb drops
in igmp6_event_query() and igmp6_event_report()")) I think the
synchronize_net() call in ipv6_mc_down() is not needed.
Under load, synchronize_net() can last between 200 usec and 5 ms.
KASAN seems to agree as well.
Fixes: f185de28d9 ("mld: add new workqueues for process mld events")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Taehee Yoo <ap420073@gmail.com>
Cc: Cong Wang <xiyou.wangcong@gmail.com>
Cc: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f0ddf15f0a74c27eb4b2271a90e69948acc3fa2c ]
The two tests that make use of multicast routig (router.sh and
router_multicast.sh) are currently failing in the netdev CI because the
kernel is missing multicast routing support.
Fix by adding the required config entries.
Fixes: 6d4efada3b ("selftests: forwarding: Add multicast routing test")
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240208165538.1303021-1-idosch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4acf4e62cd572b0c806035046b3698f5585ab821 ]
The config file contains a partial kernel configuration to be used by
`virtme-configkernel --custom'. The presumption is that the config file
contains all Kconfig options needed by the selftests from the directory.
In net/forwarding/config, many are missing, which manifests as spurious
failures when running the selftests, with messages about unknown device
types, qdisc kinds or classifier actions. Add the missing configurations.
Tested the resulting configuration using virtme-ng as follows:
# vng -b -f tools/testing/selftests/net/forwarding/config
# vng --user root
(within the VM:)
# make -C tools/testing/selftests TARGETS=net/forwarding run_tests
Signed-off-by: Petr Machata <petrm@nvidia.com>
Link: https://lore.kernel.org/r/025abded7ff9cea5874a7fe35dcd3fd41bf5e6ac.1706286755.git.petrm@nvidia.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Stable-dep-of: f0ddf15f0a74 ("selftests: forwarding: Add missing multicast routing config entries")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0628c03934187be33942580e10bb9afcc61adeed ]
'-fPIC' as an option to the linker does not do what it seems like it
should. With ld.bfd, it is treated as '-f PIC', which does not make
sense based on the meaning of '-f':
-f SHLIB, --auxiliary SHLIB Auxiliary filter for shared object symbol table
When building with ld.lld (currently under review in a GitHub pull
request), it just errors out because '-f' means nothing and neither does
'-fPIC':
ld.lld: error: unknown argument '-fPIC'
'-fPIC' was blindly copied from CFLAGS when the vDSO stopped being
linked with '$(CC)', it should not be needed. Remove it to clear up the
build failure with ld.lld.
Fixes: 2b2a25845d ("s390/vdso: Use $(LD) instead of $(CC) to link vDSO")
Link: https://github.com/llvm/llvm-project/pull/75643
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Fangrui Song <maskray@google.com>
Link: https://lore.kernel.org/r/20240130-s390-vdso-drop-fpic-from-ldflags-v1-1-094ad104fc55@kernel.org
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 225d09d6e5f3870560665a1829d2db79330b4c58 ]
When the device drivers are initialized, a sysfs directory
is created. This contains many attributes which are allocated with
kzalloc(). Should it fail, the memory for the attributes already
created is freed in attr_event_free(). Its second parameter is number
of attribute elements to delete. This parameter is off by one.
When i. e. the 10th attribute fails to get created, attributes
numbered 0 to 9 should be deleted. Currently only attributes
numbered 0 to 8 are deleted.
Fixes: 39d62336f5 ("s390/pai: add support for cryptography counters")
Reported-by: Sumanth Korikkar <sumanthk@linux.ibm.com>
Signed-off-by: Thomas Richter <tmricht@linux.ibm.com>
Acked-by: Sumanth Korikkar <sumanthk@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d5bd4041cd70faf26fc9a54bd6f172537bbe77f3 ]
The firmware (later) actually uses the values even for keys
that are invalid as far as the host is concerned, later in
rekeying, and then only sets the low 48 bits since the PNs
are only 48 bits over the air. It does, however, compare the
full 64 bits later, obviously causing problems.
Remove the memset and use kzalloc instead to avoid any old
heap data leaking to the firmware. We already init all the
other fields in the struct anyway. This leaves the data set
to zero for any unused fields, so the firmware can look at
them safely even if they're not used right now.
Fixes: 79e561f0f0 ("iwlwifi: mvm: d3: implement RSC command version 5")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240206175739.462101146fef.I10f3855b99417af4247cff04af78dcbc6cb75c9c@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 903fad4394666bc23975c93fb58f137ce64b5192 ]
The .BTF_ids section is pre-filled with zeroed BTF ID entries during the
build and afterwards patched by resolve_btfids with correct values.
Since resolve_btfids always writes in host-native endianness, it relies
on libelf to do the translation when the target ELF is cross-compiled to
a different endianness (this was introduced in commit 61e8aeda93
("bpf: Fix libelf endian handling in resolv_btfids")).
Unfortunately, the translation will corrupt the flags fields of SET8
entries because these were written during vmlinux compilation and are in
the correct endianness already. This will lead to numerous selftests
failures such as:
$ sudo ./test_verifier 502 502
#502/p sleepable fentry accept FAIL
Failed to load prog 'Invalid argument'!
bpf_fentry_test1 is not sleepable
verification time 34 usec
stack depth 0
processed 0 insns (limit 1000000) max_states_per_insn 0 total_states 0 peak_states 0 mark_read 0
Summary: 0 PASSED, 0 SKIPPED, 1 FAILED
Since it's not possible to instruct libelf to translate just certain
values, let's manually bswap the flags (both global and entry flags) in
resolve_btfids when needed, so that libelf then translates everything
correctly.
Fixes: ef2c6f370a ("tools/resolve_btfids: Add support for 8-byte BTF sets")
Signed-off-by: Viktor Malik <vmalik@redhat.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/7b6bff690919555574ce0f13d2a5996cacf7bf69.1707223196.git.vmalik@redhat.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9707ac4fe2f5bac6406d2403f8b8a64d7b3d8e43 ]
Instead of using magic offsets to access BTF ID set data, leverage types
from btf_ids.h (btf_id_set and btf_id_set8) which define the actual
layout of the data. Thanks to this change, set sorting should also
continue working if the layout changes.
This requires to sync the definition of 'struct btf_id_set8' from
include/linux/btf_ids.h to tools/include/linux/btf_ids.h. We don't sync
the rest of the file at the moment, b/c that would require to also sync
multiple dependent headers and we don't need any other defs from
btf_ids.h.
Signed-off-by: Viktor Malik <vmalik@redhat.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Acked-by: Daniel Xu <dxu@dxuuu.xyz>
Link: https://lore.kernel.org/bpf/ff7f062ddf6a00815fda3087957c4ce667f50532.1707223196.git.vmalik@redhat.com
Stable-dep-of: 903fad439466 ("tools/resolve_btfids: Fix cross-compilation to non-host endianness")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5f623835584f1c8d1030666796f40c47a448ce0b ]
The driver only used the number of pwm channels to set the pwm_chip's
npwm member. The result is that if there are more capture channels than
PWM channels specified in the device tree, only a part of the capture
channel is usable. Fix that by passing the bigger channel count to the
pwm framework. This makes it possible that the .apply() callback is
called with .hwpwm >= pwm_num_devs, catch that case and return an error
code.
Fixes: c97267ae83 ("pwm: sti: Add PWM capture callback")
Link: https://lore.kernel.org/r/20240204212043.2951852-2-u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d04d5882cd678b898a9d7c5aee6afbe9e6e77fcd ]
The commit d51507098f ("printk: disable optimistic spin
during panic") added checks to avoid becoming a console waiter
if a panic is in progress.
However, the transition to panic can occur while there is
already a waiter. The current owner should not pass the lock to
the waiter because it might get stopped or blocked anytime.
Also the panic context might pass the console lock owner to an
already stopped waiter by mistake. It might happen when
console_flush_on_panic() ignores the current lock owner, for
example:
CPU0 CPU1
---- ----
console_lock_spinning_enable()
console_trylock_spinning()
[CPU1 now console waiter]
NMI: panic()
panic_other_cpus_shutdown()
[stopped as console waiter]
console_flush_on_panic()
console_lock_spinning_enable()
[print 1 record]
console_lock_spinning_disable_and_check()
[handover to stopped CPU1]
This results in panic() not flushing the panic messages.
Fix these problems by disabling all spinning operations
completely during panic().
Another advantage is that it prevents possible deadlocks caused
by "console_owner_lock". The panic() context does not need to
take it any longer. The lockless checks are safe because the
functions become NOPs when they see the panic in progress. All
operations manipulating the state are still synchronized by the
lock even when non-panic CPUs would notice the panic
synchronously.
The current owner might stay spinning. But non-panic() CPUs
would get stopped anyway and the panic context will never start
spinning.
Fixes: dbdda842fe ("printk: Add console owner and waiter logic to load balance console writes")
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20240207134103.1357162-12-john.ogness@linutronix.de
Signed-off-by: Petr Mladek <pmladek@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
