commit 09abfe7b5b upstream.
The RDMA CM will select a source device and address by consulting
the routing table if no source address is passed into
rdma_resolve_address(). Userspace will ask for this by passing an
all-zero source address in the RESOLVE_IP command. Unfortunately
the new check for non-zero address size rejects this with EINVAL,
which breaks valid userspace applications.
Fix this by explicitly allowing a zero address family for the source.
Fixes: 2975d5de64 ("RDMA/ucma: Check AF family prior resolving address")
Cc: <stable@vger.kernel.org>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 26bff1bd74 upstream.
The c4iw_rdev_close() logic was not releasing all the hw
resources (PBL and RQT memory) during the device removal
event (driver unload / system reboot). This can cause panic
in gen_pool_destroy().
The module remove function will wait for all the hw
resources to be released during the device removal event.
Fixes c12a67fe(iw_cxgb4: free EQ queue memory on last deref)
Signed-off-by: Raju Rangoju <rajur@chelsio.com>
Reviewed-by: Steve Wise <swise@opengridcomputing.com>
Cc: stable@vger.kernel.org
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7d83fb1425 upstream.
During the "insert range" fallocate operation, i_size grows by the
specified 'len' bytes. XFS verifies that i_size + len < s_maxbytes, as
it should. But this comparison is done using the signed 'loff_t', and
'i_size + len' can wrap around to a negative value, causing the check to
incorrectly pass, resulting in an inode with "negative" i_size. This is
possible on 64-bit platforms, where XFS sets s_maxbytes = LLONG_MAX.
ext4 and f2fs don't run into this because they set a smaller s_maxbytes.
Fix it by using subtraction instead.
Reproducer:
xfs_io -f file -c "truncate $(((1<<63)-1))" -c "finsert 0 4096"
Fixes: a904b1ca57 ("xfs: Add support FALLOC_FL_INSERT_RANGE for fallocate")
Cc: <stable@vger.kernel.org> # v4.1+
Originally-From: Eric Biggers <ebiggers@google.com>
Signed-off-by: Eric Biggers <ebiggers@google.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
[darrick: fix signed integer addition overflow too]
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f372b81101 upstream.
This patch adds the correct platform data information for the Caroline
Chromebook, so that the mouse button does not get stuck in pressed state
after the first click.
The Samus button keymap and platform data definition are the correct
ones for Caroline, so they have been reused here.
Signed-off-by: Vittorio Gambaletta <linuxbugs@vittgam.net>
Signed-off-by: Salvatore Bellizzi <lkml@seppia.net>
Tested-by: Guenter Roeck <groeck@chromium.org>
Cc: stable@vger.kernel.org
[dtor: adjusted vendor spelling to match shipping firmware]
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6bd6ae6396 upstream.
UI_SET_LEDBIT ioctl() causes the following KASAN splat when used with
led > LED_CHARGING:
[ 1274.663418] BUG: KASAN: slab-out-of-bounds in input_leds_connect+0x611/0x730 [input_leds]
[ 1274.663426] Write of size 8 at addr ffff88003377b2c0 by task ckb-next-daemon/5128
This happens because we were writing to the led structure before making
sure that it exists.
Reported-by: Tasos Sahanidis <tasos@tasossah.com>
Tested-by: Tasos Sahanidis <tasos@tasossah.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 76b3421b39 upstream.
Some control API callbacks in aloop driver are too lazy to take the
loopback->cable_lock and it results in possible races of cable access
while it's being freed. It eventually lead to a UAF, as reported by
fuzzer recently.
This patch covers such control API callbacks and add the proper mutex
locks.
Reported-by: DaeRyong Jeong <threeearcat@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 306a4f3ca7 upstream.
Show paused ALSA aloop device as inactive, i.e. the control
"PCM Slave Active" set as false. Notification sent upon state change.
This makes it possible for client capturing from aloop device to know if
data is expected. Without it the client expects data even if playback
is paused.
Signed-off-by: Robert Rosengren <robert.rosengren@axis.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8f22e52528 upstream.
The sequencer virmidi code has an open race at its output trigger
callback: namely, virmidi keeps only one event packet for processing
while it doesn't protect for concurrent output trigger calls.
snd_virmidi_output_trigger() tries to process the previously
unfinished event before starting encoding the given MIDI stream, but
this is done without any lock. Meanwhile, if another rawmidi stream
starts the output trigger, this proceeds further, and overwrites the
event package that is being processed in another thread. This
eventually corrupts and may lead to the invalid memory access if the
event type is like SYSEX.
The fix is just to move the spinlock to cover both the pending event
and the new stream.
The bug was spotted by a new fuzzer, RaceFuzzer.
BugLink: http://lkml.kernel.org/r/20180426045223.GA15307@dragonet.kaist.ac.kr
Reported-by: DaeRyong Jeong <threeearcat@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f13876e2c3 upstream.
Since snd_pcm_ioctl_xfern_compat() has no PCM state check, it may go
further and hit the sanity check pcm_sanity_check() when the ioctl is
called right after open. It may eventually spew a kernel warning, as
triggered by syzbot, depending on kconfig.
The lack of PCM state check there was just an oversight. Although
it's no real crash, the spurious kernel warning is annoying, so let's
add the proper check.
Reported-by: syzbot+1dac3a4f6bc9c1c675d4@syzkaller.appspotmail.com
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 71a0483d56 upstream.
The Quectel EP06 is a Cat. 6 LTE modem, and the interface mapping is as
follows:
0: Diag
1: NMEA
2: AT
3: Modem
Interface 4 is QMI and interface 5 is ADB, so they are blacklisted.
This patch should also be considered for -stable. The QMI-patch for this
modem is already in the -stable-queue.
v1->v2:
* Updated commit prefix (thanks Johan Hovold)
* Updated commit message slightly.
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
Acked-by: Johan Hovold <johan@kernel.org>
Cc: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6df765dca3 upstream.
Commit e61c38d85b ("serial: imx: setup DCEDTE early and ensure DCD and
RI irqs to be off") has a flaw: While UCR3 and UFCR were modified using
read-modify-write before it switched to write register values
independent of the previous state. That's a good idea in principle (and
that's why I did it) but needs more care.
This patch reinstates read-modify-write for UFCR and for UCR3 ensures
that RXDMUXSEL and ADNIMP are set for post imx1.
Fixes: e61c38d85b ("serial: imx: setup DCEDTE early and ensure DCD and RI irqs to be off")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Mika Penttilä <mika.penttila@nextfour.com>
Tested-by: Mika Penttilä <mika.penttila@nextfour.com>
Acked-by: Steve Twiss <stwiss.opensource@diasemi.com>
Tested-by: Steve Twiss <stwiss.opensource@diasemi.com>
Cc: Chris Ruehl <chris.ruehl@gtsys.com.hk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 85bd0ba1ff upstream.
Although we've implemented PSCI 0.1, 0.2 and 1.0, we expose either 0.1
or 1.0 to a guest, defaulting to the latest version of the PSCI
implementation that is compatible with the requested version. This is
no different from doing a firmware upgrade on KVM.
But in order to give a chance to hypothetical badly implemented guests
that would have a fit by discovering something other than PSCI 0.2,
let's provide a new API that allows userspace to pick one particular
version of the API.
This is implemented as a new class of "firmware" registers, where
we expose the PSCI version. This allows the PSCI version to be
save/restored as part of a guest migration, and also set to
any supported version if the guest requires it.
Cc: stable@vger.kernel.org #4.16
Reviewed-by: Christoffer Dall <cdall@kernel.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8fe4592438 upstream.
When iterating through a map, we need to find a key that does not exist
in the map so map_get_next_key will give us the first key of the map.
This often requires a lot of guessing in production systems.
This patch makes map_get_next_key return the first key when the key
pointer in the parameter is NULL.
Signed-off-by: Teng Qin <qinteng@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Chenbo Feng <fengc@google.com>
Cc: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f0295e047f upstream.
The current EEH callbacks can race with a driver unbind. This can
result in a backtraces like this:
EEH: Frozen PHB#0-PE#1fc detected
EEH: PE location: S000009, PHB location: N/A
CPU: 2 PID: 2312 Comm: kworker/u258:3 Not tainted 4.15.6-openpower1 #2
Workqueue: nvme-wq nvme_reset_work [nvme]
Call Trace:
dump_stack+0x9c/0xd0 (unreliable)
eeh_dev_check_failure+0x420/0x470
eeh_check_failure+0xa0/0xa4
nvme_reset_work+0x138/0x1414 [nvme]
process_one_work+0x1ec/0x328
worker_thread+0x2e4/0x3a8
kthread+0x14c/0x154
ret_from_kernel_thread+0x5c/0xc8
nvme nvme1: Removing after probe failure status: -19
<snip>
cpu 0x23: Vector: 300 (Data Access) at [c000000ff50f3800]
pc: c0080000089a0eb0: nvme_error_detected+0x4c/0x90 [nvme]
lr: c000000000026564: eeh_report_error+0xe0/0x110
sp: c000000ff50f3a80
msr: 9000000000009033
dar: 400
dsisr: 40000000
current = 0xc000000ff507c000
paca = 0xc00000000fdc9d80 softe: 0 irq_happened: 0x01
pid = 782, comm = eehd
Linux version 4.15.6-openpower1 (smc@smc-desktop) (gcc version 6.4.0 (Buildroot 2017.11.2-00008-g4b6188e)) #2 SM P Tue Feb 27 12:33:27 PST 2018
enter ? for help
eeh_report_error+0xe0/0x110
eeh_pe_dev_traverse+0xc0/0xdc
eeh_handle_normal_event+0x184/0x4c4
eeh_handle_event+0x30/0x288
eeh_event_handler+0x124/0x170
kthread+0x14c/0x154
ret_from_kernel_thread+0x5c/0xc8
The first part is an EEH (on boot), the second half is the resulting
crash. nvme probe starts the nvme_reset_work() worker thread. This
worker thread starts touching the device which see a device error
(EEH) and hence queues up an event in the powerpc EEH worker
thread. nvme_reset_work() then continues and runs
nvme_remove_dead_ctrl_work() which results in unbinding the driver
from the device and hence releases all resources. At the same time,
the EEH worker thread starts doing the EEH .error_detected() driver
callback, which no longer works since the resources have been freed.
This fixes the problem in the same way the generic PCIe AER code (in
drivers/pci/pcie/aer/aerdrv_core.c) does. It makes the EEH code hold
the device_lock() while performing the driver EEH callbacks and
associated code. This ensures either the callbacks are no longer
register, or if they are registered the driver will not be removed
from underneath us.
This has been broken forever. The EEH call backs were first introduced
in 2005 (in 77bd741561) but it's not clear if a lock was needed back
then.
Fixes: 77bd741561 ("[PATCH] powerpc: PCI Error Recovery: PPC64 core recovery routines")
Cc: stable@vger.kernel.org # v2.6.16+
Signed-off-by: Michael Neuling <mikey@neuling.org>
Reviewed-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit da6fa7ef67 upstream.
Recent AMD systems support using MWAIT for C1 state. However, MWAIT will
not allow deeper cstates than C1 on current systems.
play_dead() expects to use the deepest state available. The deepest state
available on AMD systems is reached through SystemIO or HALT. If MWAIT is
available, it is preferred over the other methods, so the CPU never reaches
the deepest possible state.
Don't try to use MWAIT to play_dead() on AMD systems. Instead, use CPUIDLE
to enter the deepest state advertised by firmware. If CPUIDLE is not
available then fallback to HALT.
Signed-off-by: Yazen Ghannam <yazen.ghannam@amd.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Borislav Petkov <bp@suse.de>
Cc: stable@vger.kernel.org
Cc: Yazen Ghannam <Yazen.Ghannam@amd.com>
Link: https://lkml.kernel.org/r/20180403140228.58540-1-Yazen.Ghannam@amd.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1a512c0882 upstream.
A bugfix broke the x32 shmid64_ds and msqid64_ds data structure layout
(as seen from user space) a few years ago: Originally, __BITS_PER_LONG
was defined as 64 on x32, so we did not have padding after the 64-bit
__kernel_time_t fields, After __BITS_PER_LONG got changed to 32,
applications would observe extra padding.
In other parts of the uapi headers we seem to have a mix of those
expecting either 32 or 64 on x32 applications, so we can't easily revert
the path that broke these two structures.
Instead, this patch decouples x32 from the other architectures and moves
it back into arch specific headers, partially reverting the even older
commit 73a2d096fd ("x86: remove all now-duplicate header files").
It's not clear whether this ever made any difference, since at least
glibc carries its own (correct) copy of both of these header files,
so possibly no application has ever observed the definitions here.
Based on a suggestion from H.J. Lu, I tried out the tool from
https://github.com/hjl-tools/linux-header to find other such
bugs, which pointed out the same bug in statfs(), which also has
a separate (correct) copy in glibc.
Fixes: f4b4aae182 ("x86/headers/uapi: Fix __BITS_PER_LONG value for x32 builds")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: "H . J . Lu" <hjl.tools@gmail.com>
Cc: Jeffrey Walton <noloader@gmail.com>
Cc: stable@vger.kernel.org
Cc: "H. Peter Anvin" <hpa@zytor.com>
Link: https://lkml.kernel.org/r/20180424212013.3967461-1-arnd@arndb.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 75569c182e upstream.
Otherwise, the SQ may skip some of the register writes, or shader waves may
be allocated where we don't expect them, so that as a result we don't actually
reset all of the register SRAMs. This can lead to spurious ECC errors later on
if a shader uses an uninitialized register.
Signed-off-by: Nicolai Hähnle <nicolai.haehnle@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 682e6b4da5 upstream.
The OPAL RTC driver does not sleep in case it gets OPAL_BUSY or
OPAL_BUSY_EVENT from firmware, which causes large scheduling
latencies, up to 50 seconds have been observed here when RTC stops
responding (BMC reboot can do it).
Fix this by converting it to the standard form OPAL_BUSY loop that
sleeps.
Fixes: 628daa8d5a ("powerpc/powernv: Add RTC and NVRAM support plus RTAS fallbacks")
Cc: stable@vger.kernel.org # v3.2+
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c0f7f5b6c6 upstream.
gpstate_timer_handler() uses synchronous smp_call to set the pstate
on the requested core. This causes the below hard lockup:
smp_call_function_single+0x110/0x180 (unreliable)
smp_call_function_any+0x180/0x250
gpstate_timer_handler+0x1e8/0x580
call_timer_fn+0x50/0x1c0
expire_timers+0x138/0x1f0
run_timer_softirq+0x1e8/0x270
__do_softirq+0x158/0x3e4
irq_exit+0xe8/0x120
timer_interrupt+0x9c/0xe0
decrementer_common+0x114/0x120
-- interrupt: 901 at doorbell_global_ipi+0x34/0x50
LR = arch_send_call_function_ipi_mask+0x120/0x130
arch_send_call_function_ipi_mask+0x4c/0x130
smp_call_function_many+0x340/0x450
pmdp_invalidate+0x98/0xe0
change_huge_pmd+0xe0/0x270
change_protection_range+0xb88/0xe40
mprotect_fixup+0x140/0x340
SyS_mprotect+0x1b4/0x350
system_call+0x58/0x6c
One way to avoid this is removing the smp-call. We can ensure that the
timer always runs on one of the policy-cpus. If the timer gets
migrated to a cpu outside the policy then re-queue it back on the
policy->cpus. This way we can get rid of the smp-call which was being
used to set the pstate on the policy->cpus.
Fixes: 7bc54b652f ("timers, cpufreq/powernv: Initialize the gpstate timer as pinned")
Cc: stable@vger.kernel.org # v4.8+
Reported-by: Nicholas Piggin <npiggin@gmail.com>
Reported-by: Pridhiviraj Paidipeddi <ppaidipe@linux.vnet.ibm.com>
Signed-off-by: Shilpasri G Bhat <shilpa.bhat@linux.vnet.ibm.com>
Acked-by: Nicholas Piggin <npiggin@gmail.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Vaidyanathan Srinivasan <svaidy@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dd709e72cb upstream.
Commit 99492c39f3 ("earlycon: Fix __earlycon_table stride") tried to fix
__earlycon_table stride by forcing the earlycon_id struct alignment to 32
and asking the linker to 32-byte align the __earlycon_table symbol. This
fix was based on commit 07fca0e57f ("tracing: Properly align linker
defined symbols") which tried a similar fix for the tracing subsystem.
However, this fix doesn't quite work because there is no guarantee that
gcc will place structures packed into an array format. In fact, gcc 4.9
chooses to 64-byte align these structs by inserting additional padding
between the entries because it has no clue that they are supposed to be in
an array. If we are unlucky, the linker will assign symbol
"__earlycon_table" to a 32-byte aligned address which does not correspond
to the 64-byte aligned contents of section "__earlycon_table".
To address this same problem, the fix to the tracing system was
subsequently re-implemented using a more robust table of pointers approach
by commits:
3d56e331b6 ("tracing: Replace syscall_meta_data struct array with pointer array")
6549864629 ("tracepoints: Fix section alignment using pointer array")
e4a9ea5ee7 ("tracing: Replace trace_event struct array with pointer array")
Let's use this same "array of pointers to structs" approach for
EARLYCON_TABLE.
Fixes: 99492c39f3 ("earlycon: Fix __earlycon_table stride")
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Suggested-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Tested-by: Guenter Roeck <groeck@chromium.org>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9c55ad1c21 upstream.
ceph_con_workfn() validates con->state before calling try_read() and
then try_write(). However, try_read() temporarily releases con->mutex,
notably in process_message() and ceph_con_in_msg_alloc(), opening the
window for ceph_con_close() to sneak in, close the connection and
release con->sock. When try_write() is called on the assumption that
con->state is still valid (i.e. not STANDBY or CLOSED), a NULL sock
gets passed to the networking stack:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000020
IP: selinux_socket_sendmsg+0x5/0x20
Make sure con->state is valid at the top of try_write() and add an
explicit BUG_ON for this, similar to try_read().
Cc: stable@vger.kernel.org
Link: https://tracker.ceph.com/issues/23706
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Jason Dillaman <dillaman@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7b4c443d13 upstream.
If we go without an established session for a while, backoff delay will
climb to 30 seconds. The keepalive timeout is also 30 seconds, so it's
pretty easily hit after a prolonged hunting for a monitor: we don't get
a chance to send out a keepalive in time, which means we never get back
a keepalive ack in time, cutting an established session and attempting
to connect to a different monitor every 30 seconds:
[Sun Apr 1 23:37:05 2018] libceph: mon0 10.80.20.99:6789 session established
[Sun Apr 1 23:37:36 2018] libceph: mon0 10.80.20.99:6789 session lost, hunting for new mon
[Sun Apr 1 23:37:36 2018] libceph: mon2 10.80.20.103:6789 session established
[Sun Apr 1 23:38:07 2018] libceph: mon2 10.80.20.103:6789 session lost, hunting for new mon
[Sun Apr 1 23:38:07 2018] libceph: mon1 10.80.20.100:6789 session established
[Sun Apr 1 23:38:37 2018] libceph: mon1 10.80.20.100:6789 session lost, hunting for new mon
[Sun Apr 1 23:38:37 2018] libceph: mon2 10.80.20.103:6789 session established
[Sun Apr 1 23:39:08 2018] libceph: mon2 10.80.20.103:6789 session lost, hunting for new mon
The regular keepalive interval is 10 seconds. After ->hunting is
cleared in finish_hunting(), call __schedule_delayed() to ensure we
send out a keepalive after 10 seconds.
Cc: stable@vger.kernel.org # 4.7+
Link: http://tracker.ceph.com/issues/23537
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Jason Dillaman <dillaman@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit facb9f6eba upstream.
This means that if we do some backoff, then authenticate, and are
healthy for an extended period of time, a subsequent failure won't
leave us starting our hunting sequence with a large backoff.
Mirrors ceph.git commit d466bc6e66abba9b464b0b69687cf45c9dccf383.
Cc: stable@vger.kernel.org # 4.7+
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Jason Dillaman <dillaman@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c656941df9 upstream.
When the desired ratio is less than 256, the savesub (tolerance)
in the calculation would become 0. This will then fail the loop-
search immediately without reporting any errors.
But if the ratio is smaller enough, there is no need to calculate
the tolerance because PM divisor alone is enough to get the ratio.
So a simple fix could be just to set PM directly instead of going
into the loop-search.
Reported-by: Marek Vasut <marex@denx.de>
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Tested-by: Marek Vasut <marex@denx.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d2ffed5185 upstream.
When printing the driver_override parameter when it is 4095 and 4094
bytes long, the printing code would access invalid memory because we
need count + 1 bytes for printing.
Cfr. commits 4efe874aac ("PCI: Don't read past the end of sysfs
"driver_override" buffer") and bf563b01c2 ("driver core: platform:
Don't read past the end of "driver_override" buffer").
Fixes: 3cf3857134 ("ARM: 8256/1: driver coamba: add device binding path 'driver_override'")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Todd Kjos <tkjos@google.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5f53624662 upstream.
For AMBA devices with unconfigured driver override, the
"driver_override" sysfs virtual file is empty, while it contains
"(null)" for platform and PCI devices.
Make AMBA consistent with other buses by dropping the test for a NULL
pointer.
Note that contrary to popular belief, sprintf() handles NULL pointers
fine; they are printed as "(null)".
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Todd Kjos <tkjos@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4fa3999ee6 upstream.
When setting the PIO_ADDR_LS register during a configuration read, we
were properly passing the device number, function number and register
number, but not the bus number, causing issues when reading the
configuration of PCIe devices.
Fixes: 8c39d71036 ("PCI: aardvark: Add Aardvark PCI host controller driver")
Cc: <stable@vger.kernel.org>
Signed-off-by: Victor Gu <xigu@marvell.com>
Reviewed-by: Wilson Ding <dingwei@marvell.com>
Reviewed-by: Nadav Haklai <nadavh@marvell.com>
[Thomas: tweak commit log.]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 660661afcd upstream.
The PCI configuration space read/write functions were special casing
the situation where PCI_SLOT(devfn) != 0, and returned
PCIBIOS_DEVICE_NOT_FOUND in this case.
However, while this is what is intended for the root bus, it is not
intended for the child busses, as it prevents discovering devices with
PCI_SLOT(x) != 0. Therefore, we return PCIBIOS_DEVICE_NOT_FOUND only
if we're on the root bus.
Fixes: 8c39d71036 ("PCI: aardvark: Add Aardvark PCI host controller driver")
Cc: <stable@vger.kernel.org>
Signed-off-by: Victor Gu <xigu@marvell.com>
Reviewed-by: Wilson Ding <dingwei@marvell.com>
Reviewed-by: Nadav Haklai <nadavh@marvell.com>
[Thomas: tweak commit log.]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ea04a1dbf8 upstream.
Fill COEF to change EAPD to verb control.
Assigned codec type.
This is an additional fix over 92f974df34 ("ALSA: hda/realtek - New
vendor ID for ALC233").
[ More notes:
according to Kailang, the chip is 10ec:0235 bonding for ALC233b,
which is equivalent with ALC255. It's only used for Lenovo.
The chip needs no alc_process_coef_fw() for headset unlike ALC255. ]
Signed-off-by: Kailang Yang <kailang@realtek.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 69fa6f19b9 upstream.
As recently Smatch suggested, one place in HD-audio hwdep ioctl codes
may expand the array directly from the user-space value with
speculation:
sound/pci/hda/hda_local.h:467 get_wcaps() warn: potential spectre issue 'codec->wcaps'
As get_wcaps() itself is a fairly frequently called inline function,
and there is only one single call with a user-space value, we replace
only the latter one to open-code locally with array_index_nospec()
hardening in this patch.
BugLink: https://marc.info/?l=linux-kernel&m=152411496503418&w=2
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8d218dd811 upstream.
As Smatch recently suggested, a few places in OSS sequencer codes may
expand the array directly from the user-space value with speculation,
namely there are a significant amount of references to either
info->ch[] or dp->synths[] array:
sound/core/seq/oss/seq_oss_event.c:315 note_on_event() warn: potential spectre issue 'info->ch' (local cap)
sound/core/seq/oss/seq_oss_event.c:362 note_off_event() warn: potential spectre issue 'info->ch' (local cap)
sound/core/seq/oss/seq_oss_synth.c:470 snd_seq_oss_synth_load_patch() warn: potential spectre issue 'dp->synths' (local cap)
sound/core/seq/oss/seq_oss_event.c:293 note_on_event() warn: potential spectre issue 'dp->synths'
sound/core/seq/oss/seq_oss_event.c:353 note_off_event() warn: potential spectre issue 'dp->synths'
sound/core/seq/oss/seq_oss_synth.c:506 snd_seq_oss_synth_sysex() warn: potential spectre issue 'dp->synths'
sound/core/seq/oss/seq_oss_synth.c:580 snd_seq_oss_synth_ioctl() warn: potential spectre issue 'dp->synths'
Although all these seem doing only the first load without further
reference, we may want to stay in a safer side, so hardening with
array_index_nospec() would still make sense.
We may put array_index_nospec() at each place, but here we take a
different approach:
- For dp->synths[], change the helpers to retrieve seq_oss_synthinfo
pointer directly instead of the array expansion at each place
- For info->ch[], harden in a normal way, as there are only a couple
of places
As a result, the existing helper, snd_seq_oss_synth_is_valid() is
replaced with snd_seq_oss_synth_info(). Also, we cover MIDI device
where a similar array expansion is done, too, although it wasn't
reported by Smatch.
BugLink: https://marc.info/?l=linux-kernel&m=152411496503418&w=2
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f5e94b4c6e upstream.
When get_synthdev() is called for a MIDI device, it returns the fixed
midi_synth_dev without the use refcounting. OTOH, the caller is
supposed to unreference unconditionally after the usage, so this would
lead to unbalanced refcount.
This patch corrects the behavior and keep up the refcount balance also
for the MIDI synth device.
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
