commit b450dcce93bc2cf6d2bfaf5a0de88a94ebad8f89 upstream.
When updating the interrupt state for an emulated timer, we return
early and skip the setup of a soft timer that runs in parallel
with the guest.
While this is OK if we have set the interrupt pending, it is pretty
wrong if the guest moved CVAL into the future. In that case,
no timer is armed and the guest can wait for a very long time
(it will take a full put/load cycle for the situation to resolve).
This is specially visible with EDK2 running at EL2, but still
using the EL1 virtual timer, which in that case is fully emulated.
Any key-press takes ages to be captured, as there is no UART
interrupt and EDK2 relies on polling from a timer...
The fix is simply to drop the early return. If the timer interrupt
is pending, we will still return early, and otherwise arm the soft
timer.
Fixes: 4d74ecfa64 ("KVM: arm64: Don't arm a hrtimer for an already pending timer")
Cc: stable@vger.kernel.org
Tested-by: Dmytro Terletskyi <dmytro_terletskyi@epam.com>
Reviewed-by: Oliver Upton <oliver.upton@linux.dev>
Link: https://lore.kernel.org/r/20250204110050.150560-2-maz@kernel.org
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ab251dacfbae28772c897f068a4184f478189ff2 upstream.
The field "eip" (instruction pointer) and "esp" (stack pointer) of a task
can be read from /proc/PID/stat. These fields can be interesting for
coredump.
However, these fields were disabled by commit 0a1eb2d474 ("fs/proc: Stop
reporting eip and esp in /proc/PID/stat"), because it is generally unsafe
to do so. But it is safe for a coredumping process, and therefore
exceptions were made:
- for a coredumping thread by commit fd7d56270b ("fs/proc: Report
eip/esp in /prod/PID/stat for coredumping").
- for all other threads in a coredumping process by commit cb8f381f16
("fs/proc/array.c: allow reporting eip/esp for all coredumping
threads").
The above two commits check the PF_DUMPCORE flag to determine a coredump thread
and the PF_EXITING flag for the other threads.
Unfortunately, commit 9230738308 ("coredump: Don't perform any cleanups
before dumping core") moved coredump to happen earlier and before PF_EXITING is
set. Thus, checking PF_EXITING is no longer the correct way to determine
threads in a coredumping process.
Instead of PF_EXITING, use PF_POSTCOREDUMP to determine the other threads.
Checking of PF_EXITING was added for coredumping, so it probably can now be
removed. But it doesn't hurt to keep.
Fixes: 9230738308 ("coredump: Don't perform any cleanups before dumping core")
Cc: stable@vger.kernel.org
Cc: Eric W. Biederman <ebiederm@xmission.com>
Acked-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Kees Cook <kees@kernel.org>
Signed-off-by: Nam Cao <namcao@linutronix.de>
Link: https://lore.kernel.org/r/d89af63d478d6c64cc46a01420b46fd6eb147d6f.1735805772.git.namcao@linutronix.de
Signed-off-by: Christian Brauner <brauner@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 53036937a101b5faeaf98e7438555fa854a1a844 upstream.
Including m68k's <asm/raw_io.h> in vga.h on nommu platforms results
in conflicting defines with io_no.h for various I/O macros from the
__raw_read and __raw_write families. An example error is
In file included from arch/m68k/include/asm/vga.h:12,
from include/video/vga.h:22,
from include/linux/vgaarb.h:34,
from drivers/video/aperture.c:12:
>> arch/m68k/include/asm/raw_io.h:39: warning: "__raw_readb" redefined
39 | #define __raw_readb in_8
|
In file included from arch/m68k/include/asm/io.h:6,
from include/linux/io.h:13,
from include/linux/irq.h:20,
from include/asm-generic/hardirq.h:17,
from ./arch/m68k/include/generated/asm/hardirq.h:1,
from include/linux/hardirq.h:11,
from include/linux/interrupt.h:11,
from include/linux/trace_recursion.h:5,
from include/linux/ftrace.h:10,
from include/linux/kprobes.h:28,
from include/linux/kgdb.h:19,
from include/linux/fb.h:6,
from drivers/video/aperture.c:5:
arch/m68k/include/asm/io_no.h:16: note: this is the location of the previous definition
16 | #define __raw_readb(addr) \
|
Include <asm/io.h>, which avoids raw_io.h on nommu platforms.
Also change the defined values of some of the read/write symbols in
vga.h to __raw_read/__raw_write as the raw_in/raw_out symbols are not
generally available.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202501071629.DNEswlm8-lkp@intel.com/
Fixes: 5c3f968712 ("m68k/video: Create <asm/vga.h>")
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: linux-fbdev@vger.kernel.org
Cc: dri-devel@lists.freedesktop.org
Cc: Helge Deller <deller@gmx.de>
Cc: stable@vger.kernel.org # v3.5+
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Link: https://lore.kernel.org/20250107095912.130530-1-tzimmermann@suse.de
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 26701574cee6777f867f89b4a5c667817e1ee0dd upstream.
The futex operation FUTEX_OP_ANDN is supposed to implement
*(int *)UADDR2 &= ~OPARG;
The s390 implementation just implements an AND instead of ANDN.
Add the missing bitwise not operation to oparg to fix this.
This is broken since nearly 19 years, so it looks like user space is
not making use of this operation.
Fixes: 3363fbdd6f ("[PATCH] s390: futex atomic operations")
Cc: stable@vger.kernel.org
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Acked-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 57e4a9bd61c308f607bc3e55e8fa02257b06b552 upstream.
MS-SMB2 section 2.2.13.2.10 specifies that 'epoch' should be a 16-bit
unsigned integer used to track lease state changes. Change the data
type of all instances of 'epoch' from unsigned int to __u16. This
simplifies the epoch change comparisons and makes the code more
compliant with the protocol spec.
Cc: stable@vger.kernel.org
Signed-off-by: Meetakshi Setiya <msetiya@microsoft.com>
Reviewed-by: Shyam Prasad N <sprasad@microsoft.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 11f8b80ab9f99291dc88d09855b9f8f43b772335 upstream.
The tracepoints based on smb3_inf_compound_*_class have tcon id and
session id swapped around. This results in incorrect output in
`trace-cmd report`.
Fix the order of arguments to resolve this issue. The trace-cmd output
below shows the before and after of the smb3_delete_enter and
smb3_delete_done events as an example. The smb3_cmd_* events show the
correct session and tcon id for reference.
Also fix tracepoint set -> get in the SMB2_OP_GET_REPARSE case.
BEFORE:
rm-2211 [001] ..... 1839.550888: smb3_delete_enter: xid=281 sid=0x5 tid=0x3d path=\hello2.txt
rm-2211 [001] ..... 1839.550894: smb3_cmd_enter: sid=0x1ac000000003d tid=0x5 cmd=5 mid=61
rm-2211 [001] ..... 1839.550896: smb3_cmd_enter: sid=0x1ac000000003d tid=0x5 cmd=6 mid=62
rm-2211 [001] ..... 1839.552091: smb3_cmd_done: sid=0x1ac000000003d tid=0x5 cmd=5 mid=61
rm-2211 [001] ..... 1839.552093: smb3_cmd_done: sid=0x1ac000000003d tid=0x5 cmd=6 mid=62
rm-2211 [001] ..... 1839.552103: smb3_delete_done: xid=281 sid=0x5 tid=0x3d
AFTER:
rm-2501 [001] ..... 3237.656110: smb3_delete_enter: xid=88 sid=0x1ac0000000041 tid=0x5 path=\hello2.txt
rm-2501 [001] ..... 3237.656122: smb3_cmd_enter: sid=0x1ac0000000041 tid=0x5 cmd=5 mid=84
rm-2501 [001] ..... 3237.656123: smb3_cmd_enter: sid=0x1ac0000000041 tid=0x5 cmd=6 mid=85
rm-2501 [001] ..... 3237.657909: smb3_cmd_done: sid=0x1ac0000000041 tid=0x5 cmd=5 mid=84
rm-2501 [001] ..... 3237.657909: smb3_cmd_done: sid=0x1ac0000000041 tid=0x5 cmd=6 mid=85
rm-2501 [001] ..... 3237.657922: smb3_delete_done: xid=88 sid=0x1ac0000000041 tid=0x5
Cc: stable@vger.kernel.org
Signed-off-by: Ruben Devos <devosruben6@gmail.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 41b996ce83bf944de5569d6263c8dbd5513e7ed0 ]
The RXRPC_CALL_SERVER_SECURING state doesn't really belong with the other
states in the call's state set as the other states govern the call's Rx/Tx
phase transition and govern when packets can and can't be received or
transmitted. The "Securing" state doesn't actually govern the reception of
packets and would need to be split depending on whether or not we've
received the last packet yet (to mirror RECV_REQUEST/ACK_REQUEST).
The "Securing" state is more about whether or not we can start forwarding
packets to the application as recvmsg will need to decode them and the
decoding can't take place until the challenge/response exchange has
completed.
Fix this by removing the RXRPC_CALL_SERVER_SECURING state from the state
set and, instead, using a flag, RXRPC_CALL_CONN_CHALLENGING, to track
whether or not we can queue the call for reception by recvmsg() or notify
the kernel app that data is ready. In the event that we've already
received all the packets, the connection event handler will poke the app
layer in the appropriate manner.
Also there's a race whereby the app layer sees the last packet before rxrpc
has managed to end the rx phase and change the state to one amenable to
allowing a reply. Fix this by queuing the packet after calling
rxrpc_end_rx_phase().
Fixes: 17926a7932 ("[AF_RXRPC]: Provide secure RxRPC sockets for use by userspace and kernel both")
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: Simon Horman <horms@kernel.org>
cc: linux-afs@lists.infradead.org
Link: https://patch.msgid.link/20250204230558.712536-2-dhowells@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 811b8f534fd85e17077bd2ac0413bcd16cc8fb9b ]
In case of tc offload, when user space queries the kernel for tc action
statistics, tc will query the offloaded statistics from device drivers.
Among other statistics, drivers are expected to pass the number of
packets that hit the action since the last query as a 64-bit number.
Unfortunately, tc treats the number of packets as a 32-bit number,
leading to truncation and incorrect statistics when the number of
packets since the last query exceeds 0xffffffff:
$ tc -s filter show dev swp2 ingress
filter protocol all pref 1 flower chain 0
filter protocol all pref 1 flower chain 0 handle 0x1
skip_sw
in_hw in_hw_count 1
action order 1: mirred (Egress Redirect to device swp1) stolen
index 1 ref 1 bind 1 installed 58 sec used 0 sec
Action statistics:
Sent 1133877034176 bytes 536959475 pkt (dropped 0, overlimits 0 requeues 0)
[...]
According to the above, 2111-byte packets were redirected which is
impossible as only 64-byte packets were transmitted and the MTU was
1500.
Fix by treating packets as a 64-bit number:
$ tc -s filter show dev swp2 ingress
filter protocol all pref 1 flower chain 0
filter protocol all pref 1 flower chain 0 handle 0x1
skip_sw
in_hw in_hw_count 1
action order 1: mirred (Egress Redirect to device swp1) stolen
index 1 ref 1 bind 1 installed 61 sec used 0 sec
Action statistics:
Sent 1370624380864 bytes 21416005951 pkt (dropped 0, overlimits 0 requeues 0)
[...]
Which shows that only 64-byte packets were redirected (1370624380864 /
21416005951 = 64).
Fixes: 3804070235 ("net/sched: Enable netdev drivers to update statistics of offloaded actions")
Reported-by: Joe Botha <joe@atomic.ac>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250204123839.1151804-1-idosch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a70c7b3cbc0688016810bb2e0b9b8a0d6a530045 ]
This reverts commit 3ca459eaba1bf96a8c7878de84fa8872259a01e3.
The blamed commit caused a regression when neither tun->owner nor
tun->group is set. This is intended to be allowed, but now requires
CAP_NET_ADMIN.
Discussion in the referenced thread pointed out that the original
issue that prompted this patch can be resolved in userspace.
The relaxed access control may also make a device accessible when it
previously wasn't, while existing users may depend on it to not be.
This is a clean pure git revert, except for fixing the indentation on
the gid_valid line that checkpatch correctly flagged.
Fixes: 3ca459eaba1b ("tun: fix group permission check")
Link: https://lore.kernel.org/netdev/CAFqZXNtkCBT4f+PwyVRmQGoT3p1eVa01fCG_aNtpt6dakXncUg@mail.gmail.com/
Signed-off-by: Willem de Bruijn <willemb@google.com>
Cc: Ondrej Mosnacek <omosnace@redhat.com>
Cc: Stas Sergeev <stsp2@yandex.ru>
Link: https://patch.msgid.link/20250204161015.739430-1-willemdebruijn.kernel@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 638ba5089324796c2ee49af10427459c2de35f71 ]
qdisc_tree_reduce_backlog() notifies parent qdisc only if child
qdisc becomes empty, therefore we need to reduce the backlog of the
child qdisc before calling it. Otherwise it would miss the opportunity
to call cops->qlen_notify(), in the case of DRR, it resulted in UAF
since DRR uses ->qlen_notify() to maintain its active list.
Fixes: f8d4bc455047 ("net/sched: netem: account for backlog updates from child qdisc")
Cc: Martin Ottens <martin.ottens@fau.de>
Reported-by: Mingi Cho <mincho@theori.io>
Signed-off-by: Cong Wang <cong.wang@bytedance.com>
Link: https://patch.msgid.link/20250204005841.223511-4-xiyou.wangcong@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ab930483eca9f3e816c35824b5868599af0c61d7 ]
While analysing code for software and OF node for the corner case when
caller asks to read zero items in the supposed to be an array of values
I found that ACPI behaves differently to what OF does, i.e.
1. It returns -EINVAL when caller asks to read zero items from integer
array, while OF returns 0, if no other errors happened.
2. It returns -EINVAL when caller asks to read zero items from string
array, while OF returns -ENODATA, if no other errors happened.
Amend ACPI implementation to follow what OF does.
Fixes: b31384fa5d ("Driver core: Unified device properties interface for platform firmware")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://patch.msgid.link/20250203194629.3731895-1-andriy.shevchenko@linux.intel.com
[ rjw: Added empty line after a conditional ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 98a5cfd2320966f40fe049a9855f8787f0126825 ]
xen_hypercall_hvm(), which is used when running as a Xen PVH guest at
most only once during early boot, is clobbering %rbx. Depending on
whether the caller relies on %rbx to be preserved across the call or
not, this clobbering might result in an early crash of the system.
This can be avoided by using an already saved register instead of %rbx.
Fixes: b4845bb63838 ("x86/xen: add central hypercall functions")
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Jan Beulich <jbeulich@suse.com>
Reviewed-by: Andrew Cooper <andrew.cooper3@citrix.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d6179f6c6204f9932aed3a7a2100b4a295dfed9d ]
The GPIO drivers with latch interrupt support (typically types starting
with PCAL) have interrupt status registers to determine which particular
inputs have caused an interrupt. Unfortunately there is no atomic
operation to read these registers and clear the interrupt. Clearing the
interrupt is done by reading the input registers.
The code was reading the interrupt status registers, and then reading
the input registers. If an input changed between these two events it was
lost.
The solution in this patch is to revert to the non-latch version of
code, i.e. remembering the previous input status, and looking for the
changes. This system results in no more I2C transfers, so is no slower.
The latch property of the device still means interrupts will still be
noticed if the input changes back to its initial state.
Fixes: 44896beae6 ("gpio: pca953x: add PCAL9535 interrupt support for Galileo Gen2")
Signed-off-by: Mark Tomlinson <mark.tomlinson@alliedtelesis.co.nz>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20240606033102.2271916-1-mark.tomlinson@alliedtelesis.co.nz
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4241a702e0d0c2ca9364cfac08dbf134264962de ]
The rxrpc_connection attend queue is never used because conn::attend_link
is never initialised and so is always NULL'd out and thus always appears to
be busy. This requires the following fix:
(1) Fix this the attend queue problem by initialising conn::attend_link.
And, consequently, two further fixes for things masked by the above bug:
(2) Fix rxrpc_input_conn_event() to handle being invoked with a NULL
sk_buff pointer - something that can now happen with the above change.
(3) Fix the RXRPC_SKB_MARK_SERVICE_CONN_SECURED message to carry a pointer
to the connection and a ref on it.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: Jakub Kicinski <kuba@kernel.org>
cc: "David S. Miller" <davem@davemloft.net>
cc: Eric Dumazet <edumazet@google.com>
cc: Paolo Abeni <pabeni@redhat.com>
cc: Simon Horman <horms@kernel.org>
cc: linux-afs@lists.infradead.org
cc: netdev@vger.kernel.org
Fixes: f2cce89a07 ("rxrpc: Implement a mechanism to send an event notification to a connection")
Link: https://patch.msgid.link/20250203110307.7265-3-dhowells@redhat.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 235174b2bed88501fda689c113c55737f99332d8 ]
Commit 4094871db1 ("udp: only do GSO if # of segs > 1") avoided GSO
for small packets. But the kernel currently dismisses GSO requests only
after checking MTU/PMTU on gso_size. This means any packets, regardless
of their payload sizes, could be dropped when PMTU becomes smaller than
requested gso_size. We encountered this issue in production and it
caused a reliability problem that new QUIC connection cannot be
established before PMTU cache expired, while non GSO sockets still
worked fine at the same time.
Ideally, do not check any GSO related constraints when payload size is
smaller than requested gso_size, and return EMSGSIZE instead of EINVAL
on MTU/PMTU check failure to be more specific on the error cause.
Fixes: 4094871db1 ("udp: only do GSO if # of segs > 1")
Signed-off-by: Yan Zhai <yan@cloudflare.com>
Suggested-by: Willem de Bruijn <willemdebruijn.kernel@gmail.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e0efe83ed325277bb70f9435d4d9fc70bebdcca8 ]
Disable PCIe AER on the tg3 device on system reboot on a limited
list of Dell PowerEdge systems. This prevents a fatal PCIe AER event
on the tg3 device during the ACPI _PTS (prepare to sleep) method for
S5 on those systems. The _PTS is invoked by acpi_enter_sleep_state_prep()
as part of the kernel's reboot sequence as a result of commit
38f34dba80 ("PM: ACPI: reboot: Reinstate S5 for reboot").
There was an earlier fix for this problem by commit 2ca1c94ce0
("tg3: Disable tg3 device on system reboot to avoid triggering AER").
But it was discovered that this earlier fix caused a reboot hang
when some Dell PowerEdge servers were booted via ipxe. To address
this reboot hang, the earlier fix was essentially reverted by commit
9fc3bc764334 ("tg3: power down device only on SYSTEM_POWER_OFF").
This re-exposed the tg3 PCIe AER on reboot problem.
This fix is not an ideal solution because the root cause of the AER
is in system firmware. Instead, it's a targeted work-around in the
tg3 driver.
Note also that the PCIe AER must be disabled on the tg3 device even
if the system is configured to use "firmware first" error handling.
V3:
- Fix sparse warning on improper comparison of pdev->current_state
- Adhere to netdev comment style
Fixes: 9fc3bc764334 ("tg3: power down device only on SYSTEM_POWER_OFF")
Signed-off-by: Lenny Szubowicz <lszubowi@redhat.com>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3f1baa91a1fdf3de9dbad4bd615b35fab347874b ]
If XDP traffic runs on a CPU which is greater than or equal to
the number of the Tx queues of the NIC, then vmxnet3_xdp_get_tq()
always picks up queue 0 for transmission as it uses reciprocal scale
instead of simple modulo operation.
vmxnet3_xdp_xmit() and vmxnet3_xdp_xmit_frame() use the above
returned queue without any locking which can lead to race conditions
when multiple XDP xmits run in parallel on different CPU's.
This patch uses a simple module scheme when the current CPU equals or
exceeds the number of Tx queues on the NIC. It also adds locking in
vmxnet3_xdp_xmit() and vmxnet3_xdp_xmit_frame() functions.
Fixes: 54f00cce11 ("vmxnet3: Add XDP support.")
Signed-off-by: Sankararaman Jayaraman <sankararaman.jayaraman@broadcom.com>
Signed-off-by: Ronak Doshi <ronak.doshi@broadcom.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250131042340.156547-1-sankararaman.jayaraman@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 46ded709232344b5750a852747a8881763c721ab ]
Some Wake-on-LAN modes such as WAKE_FILTER may only be supported by the MAC,
while others might be only supported by the PHY. Make sure that the .get_wol()
returns the union of both rather than only that of the PHY if the PHY supports
Wake-on-LAN.
When disabling Wake-on-LAN, make sure that this is done at both the PHY
and MAC level, rather than doing an early return from the PHY driver.
Fixes: 7e400ff35c ("net: bcmgenet: Add support for PHY-based Wake-on-LAN")
Fixes: 9ee09edc05f2 ("net: bcmgenet: Properly overlay PHY and MAC Wake-on-LAN capabilities")
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20250129231342.35013-1-florian.fainelli@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c8ed6cb5d37bc09c7e25e49a670e9fd1a3bd1dfa ]
Do not access the state variable directly, instead use proper
synchronization so not stale data is read.
Fixes: e6e7f7ac03e4 ("nvme: ensure reset state check ordering")
Signed-off-by: Daniel Wagner <wagi@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 743bbd93cf29f653fae0e1416a31f03231689911 ]
Introduce a new helper ice_put_rx_mbuf() that will go through gathered
frags from current frame and will call ice_put_rx_buf() on them. Current
logic that was supposed to simplify and optimize the driver where we go
through a batch of all buffers processed in current NAPI instance turned
out to be broken for jumbo frames and very heavy load that was coming
from both multi-thread iperf and nginx/wrk pair between server and
client. The delay introduced by approach that we are dropping is simply
too big and we need to take the decision regarding page
recycling/releasing as quick as we can.
While at it, address an error path of ice_add_xdp_frag() - we were
missing buffer putting from day 1 there.
As a nice side effect we get rid of annoying and repetitive three-liner:
xdp->data = NULL;
rx_ring->first_desc = ntc;
rx_ring->nr_frags = 0;
by embedding it within introduced routine.
Fixes: 1dc1a7e7f4 ("ice: Centrallize Rx buffer recycling")
Reported-and-tested-by: Xu Du <xudu@redhat.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Co-developed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Chandan Kumar Rout <chandanx.rout@intel.com> (A Contingent Worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6daaae5ff7f3b23a2dacc9c387ff3d4f95b67cad ]
If the hotplug detect of a display is low for longer than one second
(configurable through drm_dp_cec_unregister_delay), then the CEC adapter
is unregistered since we assume the display was disconnected. If the
HPD went low for less than one second, then we check if the properties
of the CEC adapter have changed, since that indicates that we actually
switch to new hardware and we have to unregister the old CEC device and
register a new one.
Unfortunately, the test for changed properties was written poorly, and
after a new CEC capability was added to the CEC core code the test always
returned true (i.e. the properties had changed).
As a result the CEC device was unregistered and re-registered for every
HPD toggle. If the CEC remote controller integration was also enabled
(CONFIG_MEDIA_CEC_RC was set), then the corresponding input device was
also unregistered and re-registered. As a result the input device in
/sys would keep incrementing its number, e.g.:
/sys/devices/pci0000:00/0000:00:08.1/0000:e7:00.0/rc/rc0/input20
Since short HPD toggles are common, the number could over time get into
the thousands.
While not a serious issue (i.e. nothing crashes), it is not intended
to work that way.
This patch changes the test so that it only checks for the single CEC
capability that can actually change, and it ignores any other
capabilities, so this is now safe as well if new caps are added in
the future.
With the changed test the bit under #ifndef CONFIG_MEDIA_CEC_RC can be
dropped as well, so that's a nice cleanup.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Reported-by: Farblos <farblos@vodafonemail.de>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Fixes: 2c6d1fffa1 ("drm: add support for DisplayPort CEC-Tunneling-over-AUX")
Tested-by: Farblos <farblos@vodafonemail.de>
Link: https://patchwork.freedesktop.org/patch/msgid/361bb03d-1691-4e23-84da-0861ead5dbdc@xs4all.nl
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 294b2b7516fd06a8dd82e4a6118f318ec521e706 ]
When the set feature attempts fails with any NVME status code set in
nvme_set_queue_count, the function still report success. Though the
numbers of queues set to 0. This is done to support controllers in
degraded state (the admin queue is still up and running but no IO
queues).
Though there is an exception. When nvme_set_features reports an host
path error, nvme_set_queue_count should propagate this error as the
connectivity is lost, which means also the admin queue is not working
anymore.
Fixes: 9a0be7abb6 ("nvme: refactor set_queue_count")
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Daniel Wagner <wagi@kernel.org>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b8291cf3d1180b5b61299922f17c9441616a805a ]
This change adds support for the NC-SI 1.2 Get MC MAC Address command,
specified here:
https://www.dmtf.org/sites/default/files/standards/documents/DSP0222_1.2.0.pdf
It serves the exact same function as the existing OEM Get MAC Address
commands, so if a channel reports that it supports NC-SI 1.2, we prefer
to use the standard command rather than the OEM command.
Verified with an invalid MAC address and 2 valid ones:
[ 55.137072] ftgmac100 1e690000.ftgmac eth0: NCSI: Received 3 provisioned MAC addresses
[ 55.137614] ftgmac100 1e690000.ftgmac eth0: NCSI: MAC address 0: 00:00:00:00:00:00
[ 55.138026] ftgmac100 1e690000.ftgmac eth0: NCSI: MAC address 1: fa:ce:b0:0c:20:22
[ 55.138528] ftgmac100 1e690000.ftgmac eth0: NCSI: MAC address 2: fa:ce:b0:0c:20:23
[ 55.139241] ftgmac100 1e690000.ftgmac eth0: NCSI: Unable to assign 00:00:00:00:00:00 to device
[ 55.140098] ftgmac100 1e690000.ftgmac eth0: NCSI: Set MAC address to fa:ce:b0:0c:20:22
Signed-off-by: Peter Delevoryas <peter@pjd.dev>
Signed-off-by: Patrick Williams <patrick@stwcx.xyz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: 9e2bbab94b88 ("net/ncsi: fix locking in Get MAC Address handling")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 87ecfdbc699cc95fac73291b52650283ddcf929d ]
If find_linux_pte fails, IRQs will not be restored. This is unlikely
to happen in practice since it would have been reported as hanging
hosts, but it should of course be fixed anyway.
Cc: stable@vger.kernel.org
Reported-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 419cfb983ca93e75e905794521afefcfa07988bb ]
Convert PPC e500 to use __kvm_faultin_pfn()+kvm_release_faultin_page(),
and continue the inexorable march towards the demise of
kvm_pfn_to_refcounted_page().
Signed-off-by: Sean Christopherson <seanjc@google.com>
Tested-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-ID: <20241010182427.1434605-55-seanjc@google.com>
Stable-dep-of: 87ecfdbc699c ("KVM: e500: always restore irqs")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 84cf78dcd9d65c45ab73998d4ad50f433d53fb93 ]
Mark pages accessed before dropping mmu_lock when faulting in guest memory
so that shadow_map() can convert to kvm_release_faultin_page() without
tripping its lockdep assertion on mmu_lock being held. Marking pages
accessed outside of mmu_lock is ok (not great, but safe), but marking
pages _dirty_ outside of mmu_lock can make filesystems unhappy.
Signed-off-by: Sean Christopherson <seanjc@google.com>
Tested-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-ID: <20241010182427.1434605-54-seanjc@google.com>
Stable-dep-of: 87ecfdbc699c ("KVM: e500: always restore irqs")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c9be85dabb376299504e0d391d15662c0edf8273 ]
Mark the underlying page as dirty in kvmppc_e500_ref_setup()'s sole
caller, kvmppc_e500_shadow_map(), which will allow converting e500 to
__kvm_faultin_pfn() + kvm_release_faultin_page() without having to do
a weird dance between ref_setup() and shadow_map().
Opportunistically drop the redundant kvm_set_pfn_accessed(), as
shadow_map() puts the page via kvm_release_pfn_clean().
Signed-off-by: Sean Christopherson <seanjc@google.com>
Tested-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-ID: <20241010182427.1434605-53-seanjc@google.com>
Stable-dep-of: 87ecfdbc699c ("KVM: e500: always restore irqs")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1bebc7869c99d466f819dd2cffaef0edf7d7a035 ]
The F11 key on the new Lenovo Thinkpad T14 Gen 5, T16 Gen 3, and P14s
Gen 5 laptops includes a symbol showing a smartphone and a laptop
chained together. According to the user manual, it starts the Microsoft
Phone Link software used to connect to Android/iOS devices and relay
messages/calls or sync data.
As there are no suitable keycodes for this action, introduce a new one.
Signed-off-by: Illia Ostapyshyn <illia@yshyn.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Link: https://lore.kernel.org/r/20241114173930.44983-2-illia@yshyn.com
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7e24ec93aecd12e33d31e38e5af4625553bbc727 ]
As reported by the kernel test robot, the following error occurs:
sound/soc/amd/yc/acp6x-mach.c: In function 'acp6x_probe':
>> sound/soc/amd/yc/acp6x-mach.c:573:15: error: implicit declaration of function 'acpi_evaluate_integer'; did you mean 'acpi_evaluate_object'? [-Werror=implicit-function-declaration]
573 | ret = acpi_evaluate_integer(handle, "_WOV", NULL, &dmic_status);
| ^~~~~~~~~~~~~~~~~~~~~
| acpi_evaluate_object
cc1: some warnings being treated as errors
The function 'acpi_evaluate_integer' and its prototype in 'acpi_bus.h'
are only available when 'CONFIG_ACPI' is enabled. Add a 'depends on ACPI'
directive in Kconfig to ensure proper compilation.
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202501090345.pBIDRTym-lkp@intel.com/
Signed-off-by: Yu-Chun Lin <eleanor15x@gmail.com>
Link: https://patch.msgid.link/20250109171547.362412-1-eleanor15x@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cd2fd6eab480dfc247b737cf7a3d6b009c4d0f1c ]
Not all devices have an ACPI companion fwnode, so adev might be NULL. This
can e.g. (theoretically) happen when a user manually binds one of
the int3472 drivers to another i2c/platform device through sysfs.
Add a check for adev not being set and return -ENODEV in that case to
avoid a possible NULL pointer deref in skl_int3472_get_acpi_buffer().
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20241209220522.25288-1-hdegoede@redhat.com
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fcbd621567420b3a2f21f49bbc056de8b273c625 ]
kmemleak noticed that the iopf queue allocated deep down within
arm_smmu_init_structures() can be leaked by a subsequent error return
from arm_smmu_device_probe(). Furthermore, after arm_smmu_device_reset()
we will also leave the SMMU enabled with an empty Stream Table, silently
blocking all DMA. This proves rather annoying for debugging said probe
failure, so let's handle it a bit better by putting the SMMU back into
(more or less) the same state as if it hadn't probed at all.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Link: https://lore.kernel.org/r/5137901958471cf67f2fad5c2229f8a8f1ae901a.1733406914.git.robin.murphy@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 42314738906380cbd3b6e9caf3ad34e1b2d66035 ]
Add the compatible for the separate IOMMU on SDM670 for the Adreno GPU.
This IOMMU has the compatible strings:
"qcom,sdm670-smmu-v2", "qcom,adreno-smmu", "qcom,smmu-v2"
While the SMMU 500 doesn't need an entry for this specific SoC, the
SMMU v2 compatible should have its own entry, as the fallback entry in
arm-smmu.c handles "qcom,smmu-v2" without per-process page table support
unless there is an entry here. This entry can't be the
"qcom,adreno-smmu" compatible because dedicated GPU IOMMUs can also be
SMMU 500 with different handling.
Signed-off-by: Richard Acayan <mailingradian@gmail.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20241114004713.42404-6-mailingradian@gmail.com
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4b5bc2ec9a239bce261ffeafdd63571134102323 ]
Now that the following fix:
d0ceea662d45 ("x86/mm: Add _PAGE_NOPTISHADOW bit to avoid updating userspace page tables")
stops kernel_ident_mapping_init() from scribbling over the end of a
4KiB PGD by assuming the following 4KiB will be a userspace PGD,
there's no good reason for the kexec PGD to be part of a single
8KiB allocation with the control_code_page.
( It's not clear that that was the reason for x86_64 kexec doing it that
way in the first place either; there were no comments to that effect and
it seems to have been the case even before PTI came along. It looks like
it was just a happy accident which prevented memory corruption on kexec. )
Either way, it definitely isn't needed now. Just allocate the PGD
separately on x86_64, like i386 already does.
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: Baoquan He <bhe@redhat.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: Dave Young <dyoung@redhat.com>
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: Ard Biesheuvel <ardb@kernel.org>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Link: https://lore.kernel.org/r/20241205153343.3275139-6-dwmw2@infradead.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5fe71fda89745fc3cd95f70d06e9162b595c3702 ]
On a 32bit system the "keylen + sizeof(struct tipc_aead_key)" math could
have an integer wrapping issue. It doesn't matter because the "keylen"
is checked on the next line, but just to make life easier for static
analysis tools, let's re-order these conditions and avoid the integer
overflow.
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 20a0c37e44063997391430c4ae09973e9cbc3911 ]
Qualcomm regulator supports two power supply modes: HPM and LPM.
Currently, the sdhci-msm.c driver does not set the load to adjust
the current for eMMC and SD. If the regulator dont't set correct
load in LPM state, it will lead to the inability to properly
initialize eMMC and SD.
Set the correct regulator current for eMMC and SD to ensure that the
device can work normally even when the regulator is in LPM.
Signed-off-by: Yuanjie Yang <quic_yuanjiey@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20250114083514.258379-1-quic_yuanjiey@quicinc.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
