The print function dev_err() is redundant because platform_get_irq()
already prints an error.
Eliminate the follow coccicheck warnings:
./drivers/thermal/db8500_thermal.c:162:2-9: line 162 is redundant because platform_get_irq() already prints an error
./drivers/thermal/db8500_thermal.c:176:2-9: line 176 is redundant because platform_get_irq() already prints an error
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Link: https://lore.kernel.org/r/20220719003556.74460-1-yang.lee@linux.alibaba.com
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
This while loop exits with "i" set to -1 and so then it sets:
derived_table[-1] = derived_table[0] - 300;
There is no need for this assignment at all. Just delete it.
Fixes: 72b3fc61c752 ("thermal: k3_j72xx_bandgap: Add the bandgap driver support")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/YoetjwcOEzYEFp9b@kili
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
When setting up a new board, a plain "Can't register thermal zone"
didn't help me much because the thermal zones in DT were all fine. I
just had a sensor entry too much in the parent TSC node. Reword the
failure/success messages to contain the sensor number to make it easier
to understand which sensor is affected. Example output now:
rcar_gen3_thermal e6198000.thermal: Sensor 0: Loaded 1 trip points
rcar_gen3_thermal e6198000.thermal: Sensor 1: Loaded 1 trip points
rcar_gen3_thermal e6198000.thermal: Sensor 2: Loaded 1 trip points
rcar_gen3_thermal e6198000.thermal: Sensor 3: Can't register thermal zone
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/20220610200500.6727-1-wsa+renesas@sang-engineering.com
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Simplify the thermal_power_cpu_get_power trace event by removing
complicated cpumask and variable length array. Now the tools parsing trace
output don't have to hassle to get this power data. The simplified format
version uses 'policy->cpu'. Remove also the 'load' information completely
since there is very little value of it in this trace event. To get the
CPUs' load (or utilization) there are other dedicated trace hooks in the
kernel. This patch also simplifies and speeds-up the main cooling code
when that trace event is enabled.
Rename the trace event to avoid confusion of tools which parse the trace
file.
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Lukasz Luba <lukasz.luba@arm.com>
Link: https://lore.kernel.org/r/20220613124327.30766-3-lukasz.luba@arm.com
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
The use of kmap() is being deprecated in favor of kmap_local_page().
Two main problems with kmap(): (1) It comes with an overhead as mapping
space is restricted and protected by a global lock for synchronization and
(2) kmap() also requires global TLB invalidation when the kmap’s pool
wraps and it might block when the mapping space is fully utilized until a
slot becomes available.
kmap_local_page() is preferred over kmap() and kmap_atomic(). Where it
cannot mechanically replace the latters, code refactor should be considered
(special care must be taken if kernel virtual addresses are aliases in
different contexts).
With kmap_local_page() the mappings are per thread, CPU local, can take
page faults, and can be called from any context (including interrupts).
Call kmap_local_page() in firmware_loader wherever kmap() is currently
used. In firmware_rw() use the helpers copy_{from,to}_page() instead of
open coding the local mappings + memcpy().
Successfully tested with "firmware" selftests on a QEMU/KVM 32-bits VM
with 4GB RAM, booting a kernel with HIGHMEM64GB enabled.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Luis Chamberlain <mcgrof@kernel.org>
Suggested-by: Ira Weiny <ira.weiny@intel.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Fabio M. De Francesco <fmdefrancesco@gmail.com>
Link: https://lore.kernel.org/r/20220714235030.12732-1-fmdefrancesco@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Debugfs node will be run-timely checked and so local variable
should be not passed to debugfs_create_ulong(). Fix it via
debugfs_create_file() to create io_tlb_used node and calculate
used io tlb number with fops_io_tlb_used attribute.
Fixes: 20347fca71 ("swiotlb: split up the global swiotlb lock")
Signed-off-by: Tianyu Lan <tiala@microsoft.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
make html doc reports a cryptic warning with the commit named below:
kernel/dma/mapping.c:258: WARNING: Option list ends without a blank
line; unexpected unindent.
Seems the parser is a bit fussy about the tabbing and having a single
space tab causes the warning. To suppress the warning add another
tab to the list and reindent everything.
Fixes: 7c2645a2a3 ("dma-mapping: allow EREMOTEIO return code for P2PDMA transfers")
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
The uevents generated for an amba device need PID and CID information
that's available only when the amba device is powered on, clocked and
out of reset. So, if those resources aren't available, the information
can't be read to generate the uevents. To workaround this requirement,
if the resources weren't available, the device addition was deferred and
retried periodically.
However, this deferred addition retry isn't based on resources becoming
available. Instead, it's retried every 5 seconds and causes arbitrary
probe delays for amba devices and their consumers.
Also, maintaining a separate deferred-probe like mechanism is
maintenance headache.
With this commit, instead of deferring the device addition, we simply
defer the generation of uevents for the device and probing of the device
(because drivers needs PID and CID to match) until the PID and CID
information can be read. This allows us to delete all the amba specific
deferring code and also avoid the arbitrary probing delays.
Cc: Rob Herring <robh@kernel.org>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: Saravana Kannan <saravanak@google.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Cc: Nicolas Saenz Julienne <nsaenz@kernel.org>
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Kefeng Wang <wangkefeng.wang@huawei.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: patches@armlinux.org.uk
Signed-off-by: Saravana Kannan <saravanak@google.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Tested-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
The soft_restart() is declared in <asm/system_misc.h> so
include that to fix the following sparse warning:
arch/arm/kernel/reboot.c:78:6: warning: symbol 'soft_restart' was not declared. Should it be static?
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Fix the use of a pointer assignment from integer where false
is being used instead of NULL. Fix the following warning by
usign NULL:
arch/arm/mm/dma-mapping.c:712:52: warning: Using plain integer as NULL pointer
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
The arm <asm/irq_work.h> does not define arch_irq_work_raise()
so is triggering the following sparse warning. Add a definiton
to fix this:
kernel/irq_work.c:70:13: warning: symbol 'arch_irq_work_raise' was not declared. Should it be static?
arch/arm/kernel/smp.c:582:6: warning: symbol 'arch_irq_work_raise' was not declared. Should it be static?
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Simply make shadow of vmalloc area mapped on demand.
Since the virtual address of vmalloc for Arm is also between
MODULE_VADDR and 0x100000000 (ZONE_HIGHMEM), which means the shadow
address has already included between KASAN_SHADOW_START and
KASAN_SHADOW_END.
Thus we need to change nothing for memory map of Arm.
This can fix ARM_MODULE_PLTS with KASan, support KASan for higmem
and support CONFIG_VMAP_STACK with KASan.
Signed-off-by: Lecopzer Chen <lecopzer.chen@mediatek.com>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Both the i.MXRT1170 and 1050 have the same gpio controller as
"fsl,imx35-gpio". Add i.MXRT to the compatible list.
Signed-off-by: Jesse Taube <Mr.Bossman075@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
The initial code was misleading to use bitwise AND against plain number,
and the commit d3054ba1db ("gpio: 74xx-mmio: Check MMIO_74XX_DIR_IN flag
in mmio_74xx_dir_in()") missed that. Switch definitions to be defined bits
for the correct comparison.
Fixes: d3054ba1db ("gpio: 74xx-mmio: Check MMIO_74XX_DIR_IN flag in mmio_74xx_dir_in()")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Some code paths cannot guarantee the inode have any dentry alias. So
WARN_ON() all !dentry may flood the kernel logs.
For example, when an overlayfs inode is watched by inotifywait (1), and
someone is trying to read the /proc/$(pidof inotifywait)/fdinfo/INOTIFY_FD,
at that time if the dentry has been reclaimed by kernel (such as
echo 2 > /proc/sys/vm/drop_caches), there will be a WARN_ON(). The
printed call stack would be like:
? show_mark_fhandle+0xf0/0xf0
show_mark_fhandle+0x4a/0xf0
? show_mark_fhandle+0xf0/0xf0
? seq_vprintf+0x30/0x50
? seq_printf+0x53/0x70
? show_mark_fhandle+0xf0/0xf0
inotify_fdinfo+0x70/0x90
show_fdinfo.isra.4+0x53/0x70
seq_show+0x130/0x170
seq_read+0x153/0x440
vfs_read+0x94/0x150
ksys_read+0x5f/0xe0
do_syscall_64+0x59/0x1e0
entry_SYSCALL_64_after_hwframe+0x44/0xa9
So let's drop WARN_ON() to avoid kernel log flooding.
Reported-by: Hongbo Yin <yinhongbo@bytedance.com>
Signed-off-by: Jiachen Zhang <zhangjiachen.jaycee@bytedance.com>
Signed-off-by: Tianci Zhang <zhangtianci.1997@bytedance.com>
Fixes: 8ed5eec9d6 ("ovl: encode pure upper file handles")
Cc: <stable@vger.kernel.org> # v4.16
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
The current implementation of fun_xdp_tx(), used for XPD_TX, is
incorrect in that it takes an address/length pair and later releases it
with page_frag_free(). It is OK for XDP_TX but the same code is used by
ndo_xdp_xmit. In that case it loses the XDP memory type and releases the
packet incorrectly for some of the types. Assorted breakage follows.
Change fun_xdp_tx() to take xdp_frame and rely on xdp_return_frame() in
reclaim.
Fixes: db37bc177d ("net/funeth: add the data path")
Signed-off-by: Dimitris Michailidis <dmichail@fungible.com>
Link: https://lore.kernel.org/r/20220726215923.7887-1-dmichail@fungible.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Pull irqchip/genirq updates from Marc Zyngier:
* Core code update:
- Non-SMP IRQ affinity fixes, allowing UP kernel to behave similarly
to SMP ones for the purpose of interrupt affinity
- Let irq_set_chip_handler_name_locked() take a const struct irq_chip *
- Tidy-up the NOMAP irqdomain API variant
- Teach action_show() to use for_each_action_of_desc()
- Make irq_chip_request_resources_parent() allow the parent callback
to be optional
- Remove dynamic allocations from populate_parent_alloc_arg()
* New drivers:
- Merge the long awaited IRQ support for the LoongArch architecture,
with the provisional ACPICA update (to be reverted once the official
support lands)
- New Renesas RZ/G2L IRQC driver, equipped with its companion GPIO
driver
* Driver updates
- Optimise the hot path operations for the SiFive PLIC, trading the
locking for per-CPU priority masking masking operations which are
apparently faster
- Work around broken PLIC implementations that deal pretty badly with
edge-triggered interrupts. Flag two implementations as affected.
- Simplify the irq-stm32-exti driver, particularly the table that
remaps the interrupts from exti to the GIC, reducing the memory usage
- Convert the ocelot irq_chip to being immutable
- Check ioremap() return value in the MIPS GIC driver
- Move MMP driver init function declarations into the common .h
- The obligatory typo fixes
Link: https://lore.kernel.org/all/20220727192356.1860546-1-maz@kernel.org
Changes to hrtimer mode (potentially made by __hrtimer_init_sleeper on
PREEMPT_RT) are not visible to hrtimer_start_range_ns, thus not
accounted for by hrtimer_start_expires call paths. In particular,
__wait_event_hrtimeout suffers from this problem as we have, for
example:
fs/aio.c::read_events
wait_event_interruptible_hrtimeout
__wait_event_hrtimeout
hrtimer_init_sleeper_on_stack <- this might "mode |= HRTIMER_MODE_HARD"
on RT if task runs at RT/DL priority
hrtimer_start_range_ns
WARN_ON_ONCE(!(mode & HRTIMER_MODE_HARD) ^ !timer->is_hard)
fires since the latter doesn't see the change of mode done by
init_sleeper
Fix it by making __wait_event_hrtimeout call hrtimer_sleeper_start_expires,
which is aware of the special RT/DL case, instead of hrtimer_start_range_ns.
Reported-by: Bruno Goncalves <bgoncalv@redhat.com>
Signed-off-by: Juri Lelli <juri.lelli@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Daniel Bristot de Oliveira <bristot@kernel.org>
Reviewed-by: Valentin Schneider <vschneid@redhat.com>
Link: https://lore.kernel.org/r/20220627095051.42470-1-juri.lelli@redhat.com
Pull clockevent/source updates from Daniel Lezcano:
- Add the missing DT bindings for the MTU nomadik timer (Linus
Walleij)
- Fix grammar typo in the ARM global timer Kconfig option (Randy
Dunlap)
- Add the tegra186 timer and use it on the tegra234 board (Thierry
Reding)
- Add the 'CPUXGPT' CPU timer for Mediatek MT6795 and implement a
workaround to overcome an ATF bug where the timer is not correctly
initialized (AngeloGioacchino Del Regno)
- Rework the suspend/resume approach to enable the feature on the
timer even it is not an active clock and fix a compilation warning
(Claudiu Beznea)
- Add the Add R-Car Gen4 timer support along with the DT bindings
(Wolfram Sang)
- Add compatible for ti,am654-timer to support AM6 SoC (Tony Lindgren)
- Fix Kconfig option to put it back to 'bool' instead of 'tristate'
for the tegra186 (Daniel Lezcano)
- Sort 'family,type' DT bindings for the Renesas timers (Geert
Uytterhoeven)
- Add compatible 'allwinner,sun20i-d1-timer' for Allwinner D1 (Samuel
Holland)
- Remove unnecessary (void*) conversions for sun4i (XU pengfei)
- Remove unnecessary (void*) conversions for sun5i (Li zeming)
Link: https://lore.kernel.org/all/7472984e-f502-5f27-82bf-070127dd85a5@linaro.org
