commit ec663d967b upstream.
Commit cab15ce604 ("arm64: Introduce execute-only page access
permissions") allowed a valid user PTE to have the PTE_USER bit clear.
As a consequence, the pte_valid_not_user() macro in set_pte() was
replaced with pte_valid_global() under the assumption that only user
pages have the nG bit set. EFI mappings, however, also have the nG bit
set and set_pte() wrongly ignores issuing the DSB+ISB.
This patch reinstates the pte_valid_not_user() macro and adds the
PTE_UXN bit check since all kernel mappings have this bit set. For
clarity, pte_exec() is renamed to pte_user_exec() as it only checks for
the absence of PTE_UXN. Consequently, the user executable check in
set_pte_at() drops the pte_ng() test since pte_user_exec() is
sufficient.
Fixes: cab15ce604 ("arm64: Introduce execute-only page access permissions")
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 06dbf468a2 upstream.
The ipq board has these rates as 25MHz, and not 19.2 and 27. I
copy/pasted from other boards that have those rates but forgot
to fix the rates here.
Fixes: 30fc4212d5 ("arm: dts: qcom: Add more board clocks")
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ba52e75718 upstream.
Reading both fault and status registers and logging any fault should
take priority over handling status register update.
Fix by moving the status handling to later in interrupt routine.
Fixes: d7bf353fd0 ("bq24190_charger: Add support for TI BQ24190 Battery Charger")
Signed-off-by: Liam Breck <kernel@networkimprov.net>
Acked-by: Mark Greer <mgreer@animalcreek.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 68abfb8015 upstream.
Caching the fault register after a single I2C read may not keep an accurate
value.
Fix by doing two reads in irq_handle_thread() and using the cached value
elsewhere. If a safety timer fault later clears itself, we apparently don't get
an interrupt (INT), however other interrupts would refresh the register cache.
From the data sheet: "When a fault occurs, the charger device sends out INT
and keeps the fault state in REG09 until the host reads the fault register.
Before the host reads REG09 and all the faults are cleared, the charger
device would not send any INT upon new faults. In order to read the
current fault status, the host has to read REG09 two times consecutively.
The 1st reads fault register status from the last read [1] and the 2nd reads
the current fault register status."
[1] presumably a typo; should be "last fault"
Fixes: d7bf353fd0 ("bq24190_charger: Add support for TI BQ24190 Battery Charger")
Signed-off-by: Liam Breck <kernel@networkimprov.net>
Acked-by: Mark Greer <mgreer@animalcreek.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2d9fee6a42 upstream.
We wrongly get uevents for bq24190-charger and bq24190-battery on every
register change.
Fix by checking the association with charger and battery before
emitting uevent(s).
Fixes: d7bf353fd0 ("bq24190_charger: Add support for TI BQ24190 Battery Charger")
Signed-off-by: Liam Breck <kernel@networkimprov.net>
Acked-by: Mark Greer <mgreer@animalcreek.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d62acc5ef0 upstream.
The device specific data is not fully initialized on
request_threaded_irq(). This may cause a crash when the IRQ handler
tries to reference them.
Fix the issue by installing IRQ handler at the end of the probe.
Fixes: d7bf353fd0 ("bq24190_charger: Add support for TI BQ24190 Battery Charger")
Signed-off-by: Liam Breck <kernel@networkimprov.net>
Acked-by: Mark Greer <mgreer@animalcreek.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 767eee362f upstream.
The interrupt signal is TRIGGER_FALLING. This is is specified in the
data sheet PIN FUNCTIONS: "The INT pin sends active low, 256us
pulse to host to report charger device status and fault."
Also the direction can be seen in the data sheet Figure 37 "BQ24190
with D+/D- Detection and USB On-The-Go (OTG)" which shows a 10k
pull-up resistor installed for the sample configurations.
Fixes: d7bf353fd0 ("bq24190_charger: Add support for TI BQ24190 Battery Charger")
Signed-off-by: Liam Breck <kernel@networkimprov.net>
Acked-by: Mark Greer <mgreer@animalcreek.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit eac6f8b0c7 upstream.
Commit 38addce8b6 ("gcc-plugins: Add latent_entropy plugin") excludes
certain powerpc early boot code from the latent entropy plugin by adding
appropriate CFLAGS. It looks like this was supposed to cover
prom_init.o, but ended up saying init.o (which doesn't exist) instead.
Fix the typo.
Fixes: 38addce8b6 ("gcc-plugins: Add latent_entropy plugin")
Signed-off-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 496e9cb5b2 upstream.
The final paragraph of the help text is reversed. We want to enable
this option by default, and disable it if the toolchain has a working
-mprofile-kernel.
Fixes: 8c50b72a3b ("powerpc/ftrace: Add Kconfig & Make glue for mprofile-kernel")
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a7e0fb6c20 upstream.
Currently the opal_exit tracepoint usually shows the opcode as 0:
<idle>-0 [047] d.h. 635.654292: opal_entry: opcode=63
<idle>-0 [047] d.h. 635.654296: opal_exit: opcode=0 retval=0
kopald-1209 [019] d... 636.420943: opal_entry: opcode=10
kopald-1209 [019] d... 636.420959: opal_exit: opcode=0 retval=0
This is because we incorrectly load the opcode into r0 before calling
__trace_opal_exit(), whereas it expects the opcode in r3 (first function
parameter). In fact we are leaving the retval in r3, so opcode and
retval will always show the same value.
Instead load the opcode into r3, resulting in:
<idle>-0 [040] d.h. 636.618625: opal_entry: opcode=63
<idle>-0 [040] d.h. 636.618627: opal_exit: opcode=63 retval=0
Fixes: c49f63530b ("powernv: Add OPAL tracepoints")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4ab2537c42 upstream.
In commit a4b349540a ("powerpc/mm: Cleanup LPCR defines") we updated
LPCR_VRMASD wrongly as below.
-#define LPCR_VRMASD (0x1ful << (63-16))
+#define LPCR_VRMASD_SH 47
+#define LPCR_VRMASD (ASM_CONST(1) << LPCR_VRMASD_SH)
We initialize the VRMA bits in LPCR to 0x00 in kvm. Hence using a
different mask value as above while updating lpcr should not have any
impact.
This patch updates it to the correct value.
Fixes: a4b349540a ("powerpc/mm: Cleanup LPCR defines")
Reported-by: Ram Pai <linuxram@us.ibm.com>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Jia He <hejianet@gmail.com>
Acked-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bdd9968d35 upstream.
val might become 7 in which case stime[7] (array of length 7) would be
accessed during the scnprintf call later and that will cause issues.
Obviously, string concatenation is not intended here so just a comma needs
to be added to fix the issue.
Fixes: 98a2766493 ("power_supply: Add new lp8788 charger driver")
Signed-off-by: Giedrius Statkevičius <giedrius.statkevicius@gmail.com>
Acked-by: Milo Kim <milo.kim@ti.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 87ec02e740 upstream.
In case ctx_dma dma mapping fails, ahash_unmap_ctx() tries to
dma unmap an invalid address:
map_seq_out_ptr_ctx() / ctx_map_to_sec4_sg() -> goto unmap_ctx ->
-> ahash_unmap_ctx() -> dma unmap ctx_dma
There is also possible to reach ahash_unmap_ctx() with ctx_dma
uninitialzed or to try to unmap the same address twice.
Fix these by setting ctx_dma = 0 where needed:
-initialize ctx_dma in ahash_init()
-clear ctx_dma in case of mapping error (instead of holding
the error code returned by the dma map function)
-clear ctx_dma after each unmapping
Fixes: 32686d34f8 ("crypto: caam - ensure that we clean up after an error")
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7d761119a9 upstream.
The error code handling is broken as any error code that has the same
bits set as TPM_RC_HASH passes. Implemented tpm2_rc_value() helper to
parse the error value from FMT0 and FMT1 error codes so that these types
of mistakes are prevented in the future.
Fixes: 5ca4c20cfd ("keys, trusted: select hash algorithm for TPM2 chips")
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d66777caa5 upstream.
pwm4 is enabled if bit 2 of GPIO control register 4 is disabled,
not when it is enabled. Since the check is for the skip condition,
it is reversed. This applies to both IT8620 and IT8628.
Fixes: 36c4d98a78 ("hwmon: (it87) Add support for all pwm channels ...")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4617f564c0 upstream.
When calling a dm ioctl that doesn't process any data
(IOCTL_FLAGS_NO_PARAMS), the contents of the data field in struct
dm_ioctl are left initialized. Current code is incorrectly extending
the size of data copied back to user, causing the contents of kernel
stack to be leaked to user. Fix by only copying contents before data
and allow the functions processing the ioctl to override.
Signed-off-by: Adrian Salido <salidoa@google.com>
Reviewed-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dc434e056f upstream.
The setup/remove_state/instance() functions in the hotplug core code are
serialized against concurrent CPU hotplug, but unfortunately not serialized
against themself.
As a consequence a concurrent invocation of these function results in
corruption of the callback machinery because two instances try to invoke
callbacks on remote cpus at the same time. This results in missing callback
invocations and initiator threads waiting forever on the completion.
The obvious solution to replace get_cpu_online() with cpu_hotplug_begin()
is not possible because at least one callsite calls into these functions
from a get_online_cpu() locked region.
Extend the protection scope of the cpuhp_state_mutex from solely protecting
the state arrays to cover the callback invocation machinery as well.
Fixes: 5b7aa87e04 ("cpu/hotplug: Implement setup/removal interface")
Reported-and-tested-by: Bart Van Assche <Bart.VanAssche@sandisk.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: hpa@zytor.com
Cc: mingo@kernel.org
Cc: akpm@linux-foundation.org
Cc: torvalds@linux-foundation.org
Link: http://lkml.kernel.org/r/20170314150645.g4tdyoszlcbajmna@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2b1ac852eb upstream.
For readahead/fadvise cases, caller of ceph_readpages does not
hold buffer capability. Pages can be added to page cache while
there is no buffer capability. This can cause data integrity
issue.
Signed-off-by: Yan, Zheng <zyan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c130b666a9 upstream.
Commit f209fa03fc ("serial: 8250_pci: Detach low-level driver during
PCI error recovery") introduces a potential use-after-free in case the
pciserial_init_ports call in serial8250_io_resume fails, which may
happen if a memory allocation fails or if the .init quirk failed for
whatever reason). If this happen, further pci_get_drvdata will return a
pointer to freed memory.
This patch reworks the PCI recovery resume hook to restore the old priv
structure in this case, which should be ok, since the ports were already
detached. Such error during recovery causes us to give up on the
recovery.
Fixes: f209fa03fc ("serial: 8250_pci: Detach low-level driver during PCI error recovery")
Reported-by: Michal Suchanek <msuchanek@suse.com>
Signed-off-by: Gabriel Krisman Bertazi <krisman@linux.vnet.ibm.com>
Signed-off-by: Guilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f1c635b439 upstream.
Hyper-V host emulation of SCSI for virtual DVD device reports SCSI
version 0 (UNKNOWN) but is still capable of supporting REPORTLUN.
Without this patch, a GEN2 Linux guest on Hyper-V will not boot 4.11
successfully with virtual DVD ROM device. What happens is that the SCSI
scan process falls back to doing sequential probing by INQUIRY. But the
storvsc driver has a previous workaround that masks/blocks all errors
reports from INQUIRY (or MODE_SENSE) commands. This workaround causes
the scan to then populate a full set of bogus LUN's on the target and
then sends kernel spinning off into a death spiral doing block reads on
the non-existent LUNs.
By setting the correct blacklist flags, the target with the DVD device
is scanned with REPORTLUN and that works correctly.
Patch needs to go in current 4.11, it is safe but not necessary in older
kernels.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Reviewed-by: K. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1d70fe9d9c upstream.
Since commit 1107d065fd ("tpm_tis: Introduce intermediate layer for
TPM access") Atmel 3203 TPM on ThinkPad X61S (TPM firmware version 13.9)
no longer works. The initialization proceeds fine until we get and
start using chip-reported timeouts - and the chip reports C and D
timeouts of zero.
It turns out that until commit 8e54caf407 ("tpm: Provide a generic
means to override the chip returned timeouts") we had actually let
default timeout values remain in this case, so let's bring back this
behavior to make chips like Atmel 3203 work again.
Use a common code that was introduced by that commit so a warning is
printed in this case and /sys/class/tpm/tpm*/timeouts correctly says the
timeouts aren't chip-original.
This is a backport for 4.9 kernel version of the original commit, with
renaming of "TPM_TIS_ITPM_POSSIBLE" flag removed since it was only a
cosmetic change and not a part of the real bug fix.
Fixes: 1107d065fd ("tpm_tis: Introduce intermediate layer for TPM access")
Cc: stable@vger.kernel.org
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 38bd49064a upstream.
A signal can interrupt a SendReceive call which result in incoming
responses to the call being ignored. This is a problem for calls such as
open which results in the successful response being ignored. This
results in an open file resource on the server.
The patch looks into responses which were cancelled after being sent and
in case of successful open closes the open fids.
For this patch, the check is only done in SendReceive2()
RH-bz: 1403319
Signed-off-by: Sachin Prabhu <sprabhu@redhat.com>
Reviewed-by: Pavel Shilovsky <pshilov@microsoft.com>
Acked-by: Sachin Prabhu <sprabhu@redhat.com>
Signed-off-by: Pavel Shilovsky <pshilov@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 34a477e529 upstream.
On x86-32, with CONFIG_FIRMWARE and multiple CPUs, if you enable function
graph tracing and then suspend to RAM, it will triple fault and reboot when
it resumes.
The first fault happens when booting a secondary CPU:
startup_32_smp()
load_ucode_ap()
prepare_ftrace_return()
ftrace_graph_is_dead()
(accesses 'kill_ftrace_graph')
The early head_32.S code calls into load_ucode_ap(), which has an an
ftrace hook, so it calls prepare_ftrace_return(), which calls
ftrace_graph_is_dead(), which tries to access the global
'kill_ftrace_graph' variable with a virtual address, causing a fault
because the CPU is still in real mode.
The fix is to add a check in prepare_ftrace_return() to make sure it's
running in protected mode before continuing. The check makes sure the
stack pointer is a virtual kernel address. It's a bit of a hack, but
it's not very intrusive and it works well enough.
For reference, here are a few other (more difficult) ways this could
have potentially been fixed:
- Move startup_32_smp()'s call to load_ucode_ap() down to *after* paging
is enabled. (No idea what that would break.)
- Track down load_ucode_ap()'s entire callee tree and mark all the
functions 'notrace'. (Probably not realistic.)
- Pause graph tracing in ftrace_suspend_notifier_call() or bringup_cpu()
or __cpu_up(), and ensure that the pause facility can be queried from
real mode.
Reported-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Tested-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Cc: "Rafael J . Wysocki" <rjw@rjwysocki.net>
Cc: linux-acpi@vger.kernel.org
Cc: Borislav Petkov <bp@alien8.de>
Cc: Len Brown <lenb@kernel.org>
Link: http://lkml.kernel.org/r/5c1272269a580660703ed2eccf44308e790c7a98.1492123841.git.jpoimboe@redhat.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ecd43afdbe upstream.
This is not exposed to userspace debugers yet, which can be done
independently as a seperate patch !
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b05c73bd1e upstream.
Allocate buffers on HEAP instead of STACK for local structures
that are to be sent using usb_control_msg().
Signed-off-by: Maksim Salau <maksim.salau@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4d6fa57b4d upstream.
While this may appear as a humdrum one line change, it's actually quite
important. An sk_buff stores data in three places:
1. A linear chunk of allocated memory in skb->data. This is the easiest
one to work with, but it precludes using scatterdata since the memory
must be linear.
2. The array skb_shinfo(skb)->frags, which is of maximum length
MAX_SKB_FRAGS. This is nice for scattergather, since these fragments
can point to different pages.
3. skb_shinfo(skb)->frag_list, which is a pointer to another sk_buff,
which in turn can have data in either (1) or (2).
The first two are rather easy to deal with, since they're of a fixed
maximum length, while the third one is not, since there can be
potentially limitless chains of fragments. Fortunately dealing with
frag_list is opt-in for drivers, so drivers don't actually have to deal
with this mess. For whatever reason, macsec decided it wanted pain, and
so it explicitly specified NETIF_F_FRAGLIST.
Because dealing with (1), (2), and (3) is insane, most users of sk_buff
doing any sort of crypto or paging operation calls a convenient function
called skb_to_sgvec (which happens to be recursive if (3) is in use!).
This takes a sk_buff as input, and writes into its output pointer an
array of scattergather list items. Sometimes people like to declare a
fixed size scattergather list on the stack; othertimes people like to
allocate a fixed size scattergather list on the heap. However, if you're
doing it in a fixed-size fashion, you really shouldn't be using
NETIF_F_FRAGLIST too (unless you're also ensuring the sk_buff and its
frag_list children arent't shared and then you check the number of
fragments in total required.)
Macsec specifically does this:
size += sizeof(struct scatterlist) * (MAX_SKB_FRAGS + 1);
tmp = kmalloc(size, GFP_ATOMIC);
*sg = (struct scatterlist *)(tmp + sg_offset);
...
sg_init_table(sg, MAX_SKB_FRAGS + 1);
skb_to_sgvec(skb, sg, 0, skb->len);
Specifying MAX_SKB_FRAGS + 1 is the right answer usually, but not if you're
using NETIF_F_FRAGLIST, in which case the call to skb_to_sgvec will
overflow the heap, and disaster ensues.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8179a101eb upstream.
ceph_set_acl() calls __ceph_setattr() if the setacl operation needs
to modify inode's i_mode. __ceph_setattr() updates inode's i_mode,
then calls posix_acl_chmod().
The problem is that __ceph_setattr() calls posix_acl_chmod() before
sending the setattr request. The get_acl() call in posix_acl_chmod()
can trigger a getxattr request. The reply of the getxattr request
can restore inode's i_mode to its old value. The set_acl() call in
posix_acl_chmod() sees old value of inode's i_mode, so it calls
__ceph_setattr() again.
Link: http://tracker.ceph.com/issues/19688
Reported-by: Jerry Lee <leisurelysw24@gmail.com>
Signed-off-by: "Yan, Zheng" <zyan@redhat.com>
Reviewed-by: Jeff Layton <jlayton@redhat.com>
Tested-by: Luis Henriques <lhenriques@suse.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 13bf9fbff0 upstream.
The NFSv2/v3 code does not systematically check whether we decode past
the end of the buffer. This generally appears to be harmless, but there
are a few places where we do arithmetic on the pointers involved and
don't account for the possibility that a length could be negative. Add
checks to catch these.
Reported-by: Tuomas Haanpää <thaan@synopsys.com>
Reported-by: Ari Kauppi <ari@synopsys.com>
Reviewed-by: NeilBrown <neilb@suse.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e6838a29ec upstream.
A client can append random data to the end of an NFSv2 or NFSv3 RPC call
without our complaining; we'll just stop parsing at the end of the
expected data and ignore the rest.
Encoded arguments and replies are stored together in an array of pages,
and if a call is too large it could leave inadequate space for the
reply. This is normally OK because NFS RPC's typically have either
short arguments and long replies (like READ) or long arguments and short
replies (like WRITE). But a client that sends an incorrectly long reply
can violate those assumptions. This was observed to cause crashes.
Also, several operations increment rq_next_page in the decode routine
before checking the argument size, which can leave rq_next_page pointing
well past the end of the page array, causing trouble later in
svc_free_pages.
So, following a suggestion from Neil Brown, add a central check to
enforce our expectation that no NFSv2/v3 call has both a large call and
a large reply.
As followup we may also want to rewrite the encoding routines to check
more carefully that they aren't running off the end of the page array.
We may also consider rejecting calls that have any extra garbage
appended. That would be safer, and within our rights by spec, but given
the age of our server and the NFS protocol, and the fact that we've
never enforced this before, we may need to balance that against the
possibility of breaking some oddball client.
Reported-by: Tuomas Haanpää <thaan@synopsys.com>
Reported-by: Ari Kauppi <ari@synopsys.com>
Reviewed-by: NeilBrown <neilb@suse.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6e4cac23c5 upstream.
The FE setups of Intel SST bytcr_rt5640 and bytcr_rt5651 drivers carry
the ignore_suspend flag, and this prevents the suspend/resume working
properly while the stream is running, since SST core code has the
check of the running streams and returns -EBUSY. Drop these
superfluous flags for fixing the behavior.
Also, the bytcr_rt5640 driver lacks of nonatomic flag in some FE
definitions, which leads to the kernel Oops at suspend/resume like:
BUG: scheduling while atomic: systemd-sleep/3144/0x00000003
Call Trace:
dump_stack+0x5c/0x7a
__schedule_bug+0x55/0x70
__schedule+0x63c/0x8c0
schedule+0x3d/0x90
schedule_timeout+0x16b/0x320
? del_timer_sync+0x50/0x50
? sst_wait_timeout+0xa9/0x170 [snd_intel_sst_core]
? sst_wait_timeout+0xa9/0x170 [snd_intel_sst_core]
? remove_wait_queue+0x60/0x60
? sst_prepare_and_post_msg+0x275/0x960 [snd_intel_sst_core]
? sst_pause_stream+0x9b/0x110 [snd_intel_sst_core]
....
This patch addresses these appropriately, too.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c46f59e902 upstream.
arch_check_elf contains a usage of current_cpu_data that will call
smp_processor_id() with preemption enabled and therefore triggers a
"BUG: using smp_processor_id() in preemptible" warning when an fpxx
executable is loaded.
As a follow-up to commit b244614a60 ("MIPS: Avoid a BUG warning during
prctl(PR_SET_FP_MODE, ...)"), apply the same fix to arch_check_elf by
using raw_current_cpu_data instead. The rationale quoted from the previous
commit:
"It is assumed throughout the kernel that if any CPU has an FPU, then
all CPUs would have an FPU as well, so it is safe to perform the check
with preemption enabled - change the code to use raw_ variant of the
check to avoid the warning."
Fixes: 46490b5725 ("MIPS: kernel: elf: Improve the overall ABI and FPU mode checks")
Signed-off-by: James Cowgill <James.Cowgill@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/15951/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9d7f29cdb4 upstream.
calculate_min_delta() may incorrectly access a 4th element of buf2[]
which only has 3 elements. This may trigger undefined behaviour and has
been reported to cause strange crashes in start_kernel() sometime after
timer initialization when built with GCC 5.3, possibly due to
register/stack corruption:
sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 10737418237ns
CPU 0 Unable to handle kernel paging request at virtual address ffffb0aa, epc == 8067daa8, ra == 8067da84
Oops[#1]:
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 4.9.18 #51
task: 8065e3e0 task.stack: 80644000
$ 0 : 00000000 00000001 00000000 00000000
$ 4 : 8065b4d0 00000000 805d0000 00000010
$ 8 : 00000010 80321400 fffff000 812de408
$12 : 00000000 00000000 00000000 ffffffff
$16 : 00000002 ffffffff 80660000 806a666c
$20 : 806c0000 00000000 00000000 00000000
$24 : 00000000 00000010
$28 : 80644000 80645ed0 00000000 8067da84
Hi : 00000000
Lo : 00000000
epc : 8067daa8 start_kernel+0x33c/0x500
ra : 8067da84 start_kernel+0x318/0x500
Status: 11000402 KERNEL EXL
Cause : 4080040c (ExcCode 03)
BadVA : ffffb0aa
PrId : 0501992c (MIPS 1004Kc)
Modules linked in:
Process swapper/0 (pid: 0, threadinfo=80644000, task=8065e3e0, tls=00000000)
Call Trace:
[<8067daa8>] start_kernel+0x33c/0x500
Code: 24050240 0c0131f9 24849c64 <a200b0a8> 41606020 000000c0 0c1a45e6 00000000 0c1a5f44
UBSAN also detects the same issue:
================================================================
UBSAN: Undefined behaviour in arch/mips/kernel/cevt-r4k.c:85:41
load of address 80647e4c with insufficient space
for an object of type 'unsigned int'
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 4.9.18 #47
Call Trace:
[<80028f70>] show_stack+0x88/0xa4
[<80312654>] dump_stack+0x84/0xc0
[<8034163c>] ubsan_epilogue+0x14/0x50
[<803417d8>] __ubsan_handle_type_mismatch+0x160/0x168
[<8002dab0>] r4k_clockevent_init+0x544/0x764
[<80684d34>] time_init+0x18/0x90
[<8067fa5c>] start_kernel+0x2f0/0x500
=================================================================
buf2[] is intentionally only 3 elements so that the last element is the
median once 5 samples have been inserted, so explicitly prevent the
possibility of comparing against the 4th element rather than extending
the array.
Fixes: 1fa405552e ("MIPS: cevt-r4k: Dynamically calculate min_delta_ns")
Reported-by: Rabin Vincent <rabinv@axis.com>
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Tested-by: Rabin Vincent <rabinv@axis.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/15892/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 162b270c66 upstream.
KGDB is a kernel debug stub and it can't be used to debug userland as it
can only safely access kernel memory.
On MIPS however KGDB has always got the register state of sleeping
processes from the userland register context at the beginning of the
kernel stack. This is meaningless for kernel threads (which never enter
userland), and for user threads it prevents the user seeing what it is
doing while in the kernel:
(gdb) info threads
Id Target Id Frame
...
3 Thread 2 (kthreadd) 0x0000000000000000 in ?? ()
2 Thread 1 (init) 0x000000007705c4b4 in ?? ()
1 Thread -2 (shadowCPU0) 0xffffffff8012524c in arch_kgdb_breakpoint () at arch/mips/kernel/kgdb.c:201
Get the register state instead from the (partial) kernel register
context stored in the task's thread_struct for resume() to restore. All
threads now correctly appear to be in context_switch():
(gdb) info threads
Id Target Id Frame
...
3 Thread 2 (kthreadd) context_switch (rq=<optimized out>, cookie=..., next=<optimized out>, prev=0x0) at kernel/sched/core.c:2903
2 Thread 1 (init) context_switch (rq=<optimized out>, cookie=..., next=<optimized out>, prev=0x0) at kernel/sched/core.c:2903
1 Thread -2 (shadowCPU0) 0xffffffff8012524c in arch_kgdb_breakpoint () at arch/mips/kernel/kgdb.c:201
Call clobbered registers which aren't saved and exception registers
(BadVAddr & Cause) which can't be easily determined without stack
unwinding are reported as 0. The PC is taken from the return address,
such that the state presented matches that found immediately after
returning from resume().
Fixes: 8854700115 ("[MIPS] kgdb: add arch support for the kernel's kgdb core")
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Jason Wessel <jason.wessel@windriver.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/15829/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4e7655fd4f upstream.
The snd_use_lock_sync() (thus its implementation
snd_use_lock_sync_helper()) has the 5 seconds timeout to break out of
the sync loop. It was introduced from the beginning, just to be
"safer", in terms of avoiding the stupid bugs.
However, as Ben Hutchings suggested, this timeout rather introduces a
potential leak or use-after-free that was apparently fixed by the
commit 2d7d54002e ("ALSA: seq: Fix race during FIFO resize"):
for example, snd_seq_fifo_event_in() -> snd_seq_event_dup() ->
copy_from_user() could block for a long time, and snd_use_lock_sync()
goes timeout and still leaves the cell at releasing the pool.
For fixing such a problem, we remove the break by the timeout while
still keeping the warning.
Suggested-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dfb00a5693 upstream.
An abstraction of asynchronous transaction for transmission of MIDI
messages was introduced in Linux v4.4. Each driver can utilize this
abstraction to transfer MIDI messages via fixed-length payload of
transaction to a certain unit address. Filling payload of the transaction
is done by callback. In this callback, each driver can return negative
error code, however current implementation assigns the return value to
unsigned variable.
This commit changes type of the variable to fix the bug.
Reported-by: Julia Lawall <Julia.Lawall@lip6.fr>
Fixes: 585d7cba5e ("ALSA: firewire-lib: add helper functions for asynchronous transactions to transfer MIDI messages")
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
