[ Upstream commit 1d11896596 ]
The 2711 pixel valve can't produce odd horizontal timings, and
checks were added to vc4_hdmi_encoder_atomic_check and
vc4_hdmi_encoder_mode_valid to filter out/block selection of
such modes.
Modes with DRM_MODE_FLAG_DBLCLK double all the horizontal timing
values before programming them into the PV. The PV values,
therefore, can not be odd, and so the modes can be supported.
Amend the filtering appropriately.
Fixes: 57fb32e632 ("drm/vc4: hdmi: Block odd horizontal timings")
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220127135116.298278-1-maxime@cerno.tech
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d9c4e39c1f ]
If we're doing an uncached read of the directory, then we ideally want
to read only the exact set of entries that will fit in the buffer
supplied by the getdents() system call. So unlike the case where we're
reading into the page cache, let's send only one READDIR call, before
trying to fill up the buffer.
Fixes: 35df59d3ef ("NFS: Reduce number of RPC calls when doing uncached readdir")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2cba05451a ]
If the parent GPIO controller is a sleeping controller (e.g. a GPIO
controller connected to I2C), getting or setting a GPIO triggers a
might_sleep() warning. This happens because the GPIO Aggregator takes
the can_sleep flag into account only for its internal locking, not for
calling into the parent GPIO controller.
Fix this by using the gpiod_[gs]et*_cansleep() APIs when calling into a
sleeping GPIO controller.
Reported-by: Mikko Salomäki <ms@datarespons.se>
Fixes: 828546e242 ("gpio: Add GPIO Aggregator")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9a8406ba1a ]
The D-PHY specification (v1.2) explicitly mentions that the T-CLK-PRE
parameter's unit is Unit Interval(UI) and the minimum value is 8. Also,
kernel doc of the 'clk_pre' member of struct phy_configure_opts_mipi_dphy
mentions that it should be in UI. However, the dphy core driver wrongly
sets 'clk_pre' to 8000, which seems to hint that it's in picoseconds.
So, let's fix the dphy core driver to correctly reflect the T-CLK-PRE
parameter's minimum value according to the D-PHY specification.
I'm assuming that all impacted custom drivers shall program values in
TxByteClkHS cycles into hardware for the T-CLK-PRE parameter. The D-PHY
specification mentions that the frequency of TxByteClkHS is exactly 1/8
the High-Speed(HS) bit rate(each HS bit consumes one UI). So, relevant
custom driver code is changed to program those values as
DIV_ROUND_UP(cfg->clk_pre, BITS_PER_BYTE), then.
Note that I've only tested the patch with RM67191 DSI panel on i.MX8mq EVK.
Help is needed to test with other i.MX8mq, Meson and Rockchip platforms,
as I don't have the hardwares.
Fixes: 2ed869990e ("phy: Add MIPI D-PHY configuration options")
Tested-by: Liu Ying <victor.liu@nxp.com> # RM67191 DSI panel on i.MX8mq EVK
Reviewed-by: Andrzej Hajda <andrzej.hajda@intel.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com> # for phy-meson-axg-mipi-dphy.c
Tested-by: Neil Armstrong <narmstrong@baylibre.com> # for phy-meson-axg-mipi-dphy.c
Tested-by: Guido Günther <agx@sigxcpu.org> # Librem 5 (imx8mq) with it's rather picky panel
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Liu Ying <victor.liu@nxp.com>
Link: https://lore.kernel.org/r/20220124024007.1465018-1-victor.liu@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ebe2b1add1 ]
Consider a case where ffs_func_eps_disable is called from
ffs_func_disable as part of composition switch and at the
same time ffs_epfile_release get called from userspace.
ffs_epfile_release will free up the read buffer and call
ffs_data_closed which in turn destroys ffs->epfiles and
mark it as NULL. While this was happening the driver has
already initialized the local epfile in ffs_func_eps_disable
which is now freed and waiting to acquire the spinlock. Once
spinlock is acquired the driver proceeds with the stale value
of epfile and tries to free the already freed read buffer
causing use-after-free.
Following is the illustration of the race:
CPU1 CPU2
ffs_func_eps_disable
epfiles (local copy)
ffs_epfile_release
ffs_data_closed
if (last file closed)
ffs_data_reset
ffs_data_clear
ffs_epfiles_destroy
spin_lock
dereference epfiles
Fix this races by taking epfiles local copy & assigning it under
spinlock and if epfiles(local) is null then update it in ffs->epfiles
then finally destroy it.
Extending the scope further from the race, protecting the ep related
structures, and concurrent accesses.
Fixes: a9e6f83c2d ("usb: gadget: f_fs: stop sleeping in ffs_func_eps_disable")
Co-developed-by: Udipto Goswami <quic_ugoswami@quicinc.com>
Reviewed-by: John Keeping <john@metanate.com>
Signed-off-by: Pratham Pratap <quic_ppratap@quicinc.com>
Signed-off-by: Udipto Goswami <quic_ugoswami@quicinc.com>
Link: https://lore.kernel.org/r/1643256595-10797-1-git-send-email-quic_ugoswami@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 283d45145f ]
The port numbers for the imx8mq mipi csi controller are wrong and
the mipi driver can't find any media devices as port@1 is connected
to the CSI bridge, not port@0. And port@0 is connected to the
source - the sensor. Fix this.
Fixes: bcadd5f66c ("arm64: dts: imx8mq: add mipi csi phy and csi bridge descriptions")
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6d58c5e21a ]
The correct property name is 'assigned-clock-parents', not
'assigned-clocks-parents'. Though if the platform works with the typo, one
has to wonder if the property is even needed.
Signed-off-by: Rob Herring <robh@kernel.org>
Fixes: 8b8c7d97e2 ("ARM: dts: imx7ulp: Add wdog1 node")
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 37291f60d0 ]
TX_PROT_BUS_WIDTH and RX_PROT_BUS_WIDTH are single registers with
separate bit fields for each lane. The code in xpsgtr_phy_init_sgmii was
not preserving the existing register value for other lanes, so enabling
the PHY in SGMII mode on one lane zeroed out the settings for all other
lanes, causing other PS-GTR peripherals such as USB3 to malfunction.
Use xpsgtr_clr_set to only manipulate the desired bits in the register.
Fixes: 4a33bea003 ("phy: zynqmp: Add PHY driver for the Xilinx ZynqMP Gigabit Transceiver")
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://lore.kernel.org/r/20220126001600.1592218-1-robert.hancock@calian.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5070ce8624 ]
The previous commit 4b402fa8e0 ("phy: phy-brcm-usb: support PHY on
the BCM4908") added a second "default" line for ARCH_BCM_4908 above
the original "default" line for ARCH_BRCMSTB. When two "default"
lines are used, only the first is used and this change stopped
the PHY_BRCM_USB option for being enabled for ARCH_BRCMSTB.
The fix is to use one "default line with "||".
Fixes: 4b402fa8e0 ("phy: phy-brcm-usb: support PHY on the BCM4908")
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Acked-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20211201180653.35097-4-alcooperx@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3375aa7713 ]
The dt-bindings for the UART controller only allow the following values
for Meson8 SoCs:
- "amlogic,meson8b-uart", "amlogic,meson-ao-uart"
- "amlogic,meson8b-uart"
Use the correct fallback compatible string "amlogic,meson-ao-uart" for
AO UART. Drop the "amlogic,meson-uart" compatible string from the EE
domain UART controllers.
Also update the order of the clocks to match the order defined in the
yaml bindings.
Fixes: b02d6e73f5 ("ARM: dts: meson8b: use stable UART bindings with correct gate clock")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20211227180026.4068352-4-martin.blumenstingl@googlemail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 57007bfb54 ]
The dt-bindings for the UART controller only allow the following values
for Meson8 SoCs:
- "amlogic,meson8-uart", "amlogic,meson-ao-uart"
- "amlogic,meson8-uart"
Use the correct fallback compatible string "amlogic,meson-ao-uart" for
AO UART. Drop the "amlogic,meson-uart" compatible string from the EE
domain UART controllers.
Also update the order of the clocks to match the order defined in the
yaml schema.
Fixes: 6ca7750205 ("ARM: dts: meson8: use stable UART bindings with correct gate clock")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20211227180026.4068352-3-martin.blumenstingl@googlemail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 23885389db ]
Commit e428e250fd ("ARM: dts: Configure system timers for omap3")
caused a timer regression for beagleboard revision c where the system
clockevent stops working if omap3isp module is unloaded.
Turns out we still have beagleboard revisions a-b4 capacitor c70 quirks
applied that limit the usable timers for no good reason. This also affects
the power management as we use the system clock instead of the 32k clock
source.
Let's fix the issue by adding a new omap3-beagle-ab4.dts for the old timer
quirks. This allows us to remove the timer quirks for later beagleboard
revisions. We also need to update the related timer quirk check for the
correct compatible property.
Fixes: e428e250fd ("ARM: dts: Configure system timers for omap3")
Cc: linux-kernel@vger.kernel.org
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Rob Herring <robh+dt@kernel.org>
Reported-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Tested-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 9da1e9ab82 upstream.
Commit 7707f7227f ("drm/rockchip: Add support for afbc") switched up
the rk3399_vop_big[] register windows, but it did so incorrectly.
The biggest problem is in rk3288_win23_data[] vs.
rk3368_win23_data[] .format field:
RK3288's format: VOP_REG(RK3288_WIN2_CTRL0, 0x7, 1)
RK3368's format: VOP_REG(RK3368_WIN2_CTRL0, 0x3, 5)
Bits 5:6 (i.e., shift 5, mask 0x3) are correct for RK3399, according to
the TRM.
There are a few other small differences between the 3288 and 3368
definitions that were swapped in commit 7707f7227f. I reviewed them to
the best of my ability according to the RK3399 TRM and fixed them up.
This fixes IOMMU issues (and display errors) when testing with BG24
color formats.
Fixes: 7707f7227f ("drm/rockchip: Add support for afbc")
Cc: Andrzej Pietrasiewicz <andrzej.p@collabora.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Brian Norris <briannorris@chromium.org>
Tested-by: Andrzej Pietrasiewicz <andrzej.p@collabora.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20220119161104.1.I1d01436bef35165a8cdfe9308789c0badb5ff46a@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cb1f65c1e1 upstream.
After commit e3728b50cd ("ACPI: PM: s2idle: Avoid possible race
related to the EC GPE") wakeup interrupts occurring immediately after
the one discarded by acpi_s2idle_wake() may be missed. Moreover, if
the SCI triggers again immediately after the rearming in
acpi_s2idle_wake(), that wakeup may be missed too.
The problem is that pm_system_irq_wakeup() only calls pm_system_wakeup()
when pm_wakeup_irq is 0, but that's not the case any more after the
interrupt causing acpi_s2idle_wake() to run until pm_wakeup_irq is
cleared by the pm_wakeup_clear() call in s2idle_loop(). However,
there may be wakeup interrupts occurring in that time frame and if
that happens, they will be missed.
To address that issue first move the clearing of pm_wakeup_irq to
the point at which it is known that the interrupt causing
acpi_s2idle_wake() to tun will be discarded, before rearming the SCI
for wakeup. Moreover, because that only reduces the size of the
time window in which the issue may manifest itself, allow
pm_system_irq_wakeup() to register two second wakeup interrupts in
a row and, when discarding the first one, replace it with the second
one. [Of course, this assumes that only one wakeup interrupt can be
discarded in one go, but currently that is the case and I am not
aware of any plans to change that.]
Fixes: e3728b50cd ("ACPI: PM: s2idle: Avoid possible race related to the EC GPE")
Cc: 5.4+ <stable@vger.kernel.org> # 5.4+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit da5fb9e1ad upstream.
The original version of the IORT PMCG definition had an oversight
wherein there was no way to describe the second register page for an
implementation using the recommended RELOC_CTRS feature. Although the
spec was fixed, and the final patches merged to ACPICA and Linux written
against the new version, it seems that some old firmware based on the
original revision has survived and turned up in the wild.
Add a check for the original PMCG definition, and avoid filling in the
second memory resource with nonsense if so. Otherwise it is likely that
something horrible will happen when the PMCG driver attempts to probe.
Reported-by: Michael Petlan <mpetlan@redhat.com>
Fixes: 24e5160493 ("ACPI/IORT: Add support for PMCG")
Cc: <stable@vger.kernel.org> # 5.2.x
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Link: https://lore.kernel.org/r/75628ae41c257fb73588f7bf1c4459160e04be2b.1643916258.git.robin.murphy@arm.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 63573807b2 upstream.
AER is not backed by a real request, hence we should not incorrectly
assume that when failing to send a nvme command, it is a normal request
but rather check if this is an aer and if so complete the aer (similar
to the normal completion path).
Cc: stable@vger.kernel.org
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3037b174b1 upstream.
The SocFPGA machine since commit b3ca9888f3 ("reset: socfpga: add an
early reset driver for SoCFPGA") uses reset controller, so it should
select RESET_CONTROLLER explicitly. Selecting ARCH_HAS_RESET_CONTROLLER
is not enough because it affects only default choice still allowing a
non-buildable configuration:
/usr/bin/arm-linux-gnueabi-ld: arch/arm/mach-socfpga/socfpga.o: in function `socfpga_init_irq':
arch/arm/mach-socfpga/socfpga.c:56: undefined reference to `socfpga_reset_init'
Reported-by: kernel test robot <lkp@intel.com>
Cc: <stable@vger.kernel.org>
Fixes: b3ca9888f3 ("reset: socfpga: add an early reset driver for SoCFPGA")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 42c9b28e68 upstream.
Currently, SD card fails to mount due to the following pinctrl error:
[ 11.170000] imx23-pinctrl 80018000.pinctrl: pin SSP1_DETECT already requested by 80018000.pinctrl; cannot claim for 80010000.spi
[ 11.180000] imx23-pinctrl 80018000.pinctrl: pin-65 (80010000.spi) status -22
[ 11.190000] imx23-pinctrl 80018000.pinctrl: could not request pin 65 (SSP1_DETECT) from group mmc0-pins-fixup.0 on device 80018000.pinctrl
[ 11.200000] mxs-mmc 80010000.spi: Error applying setting, reverse things back
Fix it by removing the MX23_PAD_SSP1_DETECT pin from the hog group as it
is already been used by the mmc0-pins-fixup pinctrl group.
With this change the rootfs can be mounted and the imx23-evk board can
boot successfully.
Cc: <stable@vger.kernel.org>
Fixes: bc3875f1a6 ("ARM: dts: mxs: modify mx23/mx28 dts files to use pinctrl headers")
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d3add1a951 upstream.
When a file is opened for writing, the vfs code (do_dentry_open)
calls get_write_access for the inode, thus incrementing the inode's write
count. That writer normally then creates a multi-block reservation for
the inode (i_res) that can be re-used by other writers, which speeds up
writes for applications that stupidly loop on open/write/close.
When the writes are all done, the multi-block reservation should be
deleted when the file is closed by the last "writer."
Commit 0ec9b9ea4f broke that concept when it moved the call to
gfs2_rs_delete before the check for FMODE_WRITE. Non-writers have no
business removing the multi-block reservations of writers. In fact, if
someone opens and closes the file for RO while a writer has a
multi-block reservation, the RO closer will delete the reservation
midway through the write, and this results in:
kernel BUG at fs/gfs2/rgrp.c:677! (or thereabouts) which is:
BUG_ON(rs->rs_requested); from function gfs2_rs_deltree.
This patch moves the check back inside the check for FMODE_WRITE.
Fixes: 0ec9b9ea4f ("gfs2: Check for active reservation in gfs2_release")
Cc: stable@vger.kernel.org # v5.12+
Signed-off-by: Bob Peterson <rpeterso@redhat.com>
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6a00ef4493 upstream.
I tried different pieces of code which uses __builtin_frame_address(1)
(with both gcc version 7.5.0 and 10.3.0) to verify whether it works as
expected on riscv64. The result is negative.
What the compiler had generated is as below:
31 fp = (unsigned long)__builtin_frame_address(1);
0xffffffff80006024 <+200>: ld s1,0(s0)
It takes '0(s0)' as the address of frame 1 (caller), but the actual address
should be '-16(s0)'.
| ... | <-+
+-----------------+ |
| return address | |
| previous fp | |
| saved registers | |
| local variables | |
$fp --> | ... | |
+-----------------+ |
| return address | |
| previous fp --------+
| saved registers |
$sp --> | local variables |
+-----------------+
This leads the kernel can not dump the full stack trace on riscv.
[ 7.222126][ T1] Call Trace:
[ 7.222804][ T1] [<ffffffff80006058>] dump_backtrace+0x2c/0x3a
This problem is not exposed on most riscv builds just because the '0(s0)'
occasionally is the address frame 2 (caller's caller), if only ra and fp
are stored in frame 1 (caller).
| ... | <-+
+-----------------+ |
| return address | |
$fp --> | previous fp | |
+-----------------+ |
| return address | |
| previous fp --------+
| saved registers |
$sp --> | local variables |
+-----------------+
This could be a *bug* of gcc that should be fixed. But as noted in gcc
manual "Calling this function with a nonzero argument can have
unpredictable effects, including crashing the calling program.", let's
remove the '__builtin_frame_address(1)' in backtrace code.
With this fix now it can show full stack trace:
[ 10.444838][ T1] Call Trace:
[ 10.446199][ T1] [<ffffffff8000606c>] dump_backtrace+0x2c/0x3a
[ 10.447711][ T1] [<ffffffff800060ac>] show_stack+0x32/0x3e
[ 10.448710][ T1] [<ffffffff80a005c0>] dump_stack_lvl+0x58/0x7a
[ 10.449941][ T1] [<ffffffff80a005f6>] dump_stack+0x14/0x1c
[ 10.450929][ T1] [<ffffffff804c04ee>] ubsan_epilogue+0x10/0x5a
[ 10.451869][ T1] [<ffffffff804c092e>] __ubsan_handle_load_invalid_value+0x6c/0x78
[ 10.453049][ T1] [<ffffffff8018f834>] __pagevec_release+0x62/0x64
[ 10.455476][ T1] [<ffffffff80190830>] truncate_inode_pages_range+0x132/0x5be
[ 10.456798][ T1] [<ffffffff80190ce0>] truncate_inode_pages+0x24/0x30
[ 10.457853][ T1] [<ffffffff8045bb04>] kill_bdev+0x32/0x3c
...
Signed-off-by: Changbin Du <changbin.du@gmail.com>
Fixes: eac2f3059e ("riscv: stacktrace: fix the riscv stacktrace when CONFIG_FRAME_POINTER enabled")
Cc: stable@vger.kernel.org
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f40fe31c01 upstream.
There is numa_add_cpu() when cpus online, accordingly, there should be
numa_remove_cpu() when cpus offline.
Signed-off-by: Pingfan Liu <kernelfans@gmail.com>
Fixes: 4f0e8eef77 ("riscv: Add numa support for riscv64 platform")
Cc: stable@vger.kernel.org
[Palmer: Add missing NUMA include]
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6df2a016c0 upstream.
From version 2.38, binutils default to ISA spec version 20191213. This
means that the csr read/write (csrr*/csrw*) instructions and fence.i
instruction has separated from the `I` extension, become two standalone
extensions: Zicsr and Zifencei. As the kernel uses those instruction,
this causes the following build failure:
CC arch/riscv/kernel/vdso/vgettimeofday.o
<<BUILDDIR>>/arch/riscv/include/asm/vdso/gettimeofday.h: Assembler messages:
<<BUILDDIR>>/arch/riscv/include/asm/vdso/gettimeofday.h:71: Error: unrecognized opcode `csrr a5,0xc01'
<<BUILDDIR>>/arch/riscv/include/asm/vdso/gettimeofday.h:71: Error: unrecognized opcode `csrr a5,0xc01'
<<BUILDDIR>>/arch/riscv/include/asm/vdso/gettimeofday.h:71: Error: unrecognized opcode `csrr a5,0xc01'
<<BUILDDIR>>/arch/riscv/include/asm/vdso/gettimeofday.h:71: Error: unrecognized opcode `csrr a5,0xc01'
The fix is to specify those extensions explicitely in -march. However as
older binutils version do not support this, we first need to detect
that.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Tested-by: Alexandre Ghiti <alexandre.ghiti@canonical.com>
Cc: stable@vger.kernel.org
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e3bcfda012 ]
CPUID.(EAX=7,ECX=0):EBX.FDP_EXCPTN_ONLY[bit 6] and
CPUID.(EAX=7,ECX=0):EBX.ZERO_FCS_FDS[bit 13] are "defeature"
bits. Unlike most of the other CPUID feature bits, these bits are
clear if the features are present and set if the features are not
present. These bits should be reported in KVM_GET_SUPPORTED_CPUID,
because if these bits are set on hardware, they cannot be cleared in
the guest CPUID. Doing so would claim guest support for a feature that
the hardware doesn't support and that can't be efficiently emulated.
Of course, any software (e.g WIN87EM.DLL) expecting these features to
be present likely predates these CPUID feature bits and therefore
doesn't know to check for them anyway.
Aaron Lewis added the corresponding X86_FEATURE macros in
commit cbb99c0f58 ("x86/cpufeatures: Add FDP_EXCPTN_ONLY and
ZERO_FCS_FDS"), with the intention of reporting these bits in
KVM_GET_SUPPORTED_CPUID, but I was unable to find a proposed patch on
the kvm list.
Opportunistically reordered the CPUID_7_0_EBX capability bits from
least to most significant.
Cc: Aaron Lewis <aaronlewis@google.com>
Signed-off-by: Jim Mattson <jmattson@google.com>
Message-Id: <20220204001348.2844660-1-jmattson@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b9bed78e2f ]
Set vmcs.GUEST_PENDING_DBG_EXCEPTIONS.BS, a.k.a. the pending single-step
breakpoint flag, when re-injecting a #DB with RFLAGS.TF=1, and STI or
MOVSS blocking is active. Setting the flag is necessary to make VM-Entry
consistency checks happy, as VMX has an invariant that if RFLAGS.TF is
set and STI/MOVSS blocking is true, then the previous instruction must
have been STI or MOV/POP, and therefore a single-step #DB must be pending
since the RFLAGS.TF cannot have been set by the previous instruction,
i.e. the one instruction delay after setting RFLAGS.TF must have already
expired.
Normally, the CPU sets vmcs.GUEST_PENDING_DBG_EXCEPTIONS.BS appropriately
when recording guest state as part of a VM-Exit, but #DB VM-Exits
intentionally do not treat the #DB as "guest state" as interception of
the #DB effectively makes the #DB host-owned, thus KVM needs to manually
set PENDING_DBG.BS when forwarding/re-injecting the #DB to the guest.
Note, although this bug can be triggered by guest userspace, doing so
requires IOPL=3, and guest userspace running with IOPL=3 has full access
to all I/O ports (from the guest's perspective) and can crash/reboot the
guest any number of ways. IOPL=3 is required because STI blocking kicks
in if and only if RFLAGS.IF is toggled 0=>1, and if CPL>IOPL, STI either
takes a #GP or modifies RFLAGS.VIF, not RFLAGS.IF.
MOVSS blocking can be initiated by userspace, but can be coincident with
a #DB if and only if DR7.GD=1 (General Detect enabled) and a MOV DR is
executed in the MOVSS shadow. MOV DR #GPs at CPL>0, thus MOVSS blocking
is problematic only for CPL0 (and only if the guest is crazy enough to
access a DR in a MOVSS shadow). All other sources of #DBs are either
suppressed by MOVSS blocking (single-step, code fetch, data, and I/O),
are mutually exclusive with MOVSS blocking (T-bit task switch), or are
already handled by KVM (ICEBP, a.k.a. INT1).
This bug was originally found by running tests[1] created for XSA-308[2].
Note that Xen's userspace test emits ICEBP in the MOVSS shadow, which is
presumably why the Xen bug was deemed to be an exploitable DOS from guest
userspace. KVM already handles ICEBP by skipping the ICEBP instruction
and thus clears MOVSS blocking as a side effect of its "emulation".
[1] http://xenbits.xenproject.org/docs/xtf/xsa-308_2main_8c_source.html
[2] https://xenbits.xen.org/xsa/advisory-308.html
Reported-by: David Woodhouse <dwmw2@infradead.org>
Reported-by: Alexander Graf <graf@amazon.de>
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20220120000624.655815-1-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cdf85e0c5d ]
Inject a #GP instead of synthesizing triple fault to try to avoid killing
the guest if emulation of an SEV guest fails due to encountering the SMAP
erratum. The injected #GP may still be fatal to the guest, e.g. if the
userspace process is providing critical functionality, but KVM should
make every attempt to keep the guest alive.
Signed-off-by: Sean Christopherson <seanjc@google.com>
Reviewed-by: Liam Merwick <liam.merwick@oracle.com>
Message-Id: <20220120010719.711476-10-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f80ae0ef08 ]
Similar to MSR_IA32_VMX_EXIT_CTLS/MSR_IA32_VMX_TRUE_EXIT_CTLS,
MSR_IA32_VMX_ENTRY_CTLS/MSR_IA32_VMX_TRUE_ENTRY_CTLS pair,
MSR_IA32_VMX_TRUE_PINBASED_CTLS needs to be filtered the same way
MSR_IA32_VMX_PINBASED_CTLS is currently filtered as guests may solely rely
on 'true' MSR data.
Note, none of the currently existing Windows/Hyper-V versions are known
to stumble upon the unfiltered MSR_IA32_VMX_TRUE_PINBASED_CTLS, the change
is aimed at making the filtering future proof.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Message-Id: <20220112170134.1904308-2-vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7a601e2cf6 ]
Enlightened VMCS v1 doesn't have VMX_PREEMPTION_TIMER_VALUE field,
PIN_BASED_VMX_PREEMPTION_TIMER is also filtered out already so it makes
sense to filter out VM_EXIT_SAVE_VMX_PREEMPTION_TIMER too.
Note, none of the currently existing Windows/Hyper-V versions are known
to enable 'save VMX-preemption timer value' when eVMCS is in use, the
change is aimed at making the filtering future proof.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Message-Id: <20220112170134.1904308-3-vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9e0db41e7a ]
When readl_poll_timeout() timeout, we'd better directly use its return
value.
Before this patch:
[ 2.145528] dwmac-sun8i: probe of 4500000.ethernet failed with error -14
After this patch:
[ 2.138520] dwmac-sun8i: probe of 4500000.ethernet failed with error -110
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 25e58af4be ]
The Intel P4500/P4600 SSDs do not report a subsystem NQN despite claiming
compliance to a standards version where reporting one is required.
Add the IGNORE_DEV_SUBNQN quirk to not fail the initialization of a
second such SSDs in a system.
Signed-off-by: Zheng Wu <wu.zheng@intel.com>
Signed-off-by: Ye Jinhe <jinhe.ye@intel.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 961c391217 ]
When using per-process mode and event inheritance is set to true,
forked processes will create a new perf events via inherit_event() ->
perf_event_alloc(). But these events will not have ring buffers
assigned to them. Any call to wakeup will be dropped if it's called on
an event with no ring buffer assigned because that's the object that
holds the wakeup list.
If the child event is disabled due to a call to
perf_aux_output_begin() or perf_aux_output_end(), the wakeup is
dropped leaving userspace hanging forever on the poll.
Normally the event is explicitly re-enabled by userspace after it
wakes up to read the aux data, but in this case it does not get woken
up so the event remains disabled.
This can be reproduced when using Arm SPE and 'stress' which forks once
before running the workload. By looking at the list of aux buffers read,
it's apparent that they stop after the fork:
perf record -e arm_spe// -vvv -- stress -c 1
With this patch applied they continue to be printed. This behaviour
doesn't happen when using systemwide or per-cpu mode.
Reported-by: Ruben Ayrapetyan <Ruben.Ayrapetyan@arm.com>
Signed-off-by: James Clark <james.clark@arm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20211206113840.130802-2-james.clark@arm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ac55d16385 ]
Calling dwc2_hsotg_ep_disable on ep0 (in/out) will lead to the following
logs before returning -EINVAL:
dwc2 49000000.usb-otg: dwc2_hsotg_ep_disable: called for ep0
dwc2 49000000.usb-otg: dwc2_hsotg_ep_disable: called for ep0
To avoid these two logs while suspending, start disabling the endpoint
from the index 1, as done in dwc2_hsotg_udc_stop:
/* all endpoints should be shutdown */
for (ep = 1; ep < hsotg->num_of_eps; ep++) {
if (hsotg->eps_in[ep])
dwc2_hsotg_ep_disable_lock(&hsotg->eps_in[ep]->ep);
if (hsotg->eps_out[ep])
dwc2_hsotg_ep_disable_lock(&hsotg->eps_out[ep]->ep);
}
Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Link: https://lore.kernel.org/r/20211207130101.270314-1-amelie.delaunay@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ac46d93235 ]
[Why]
DCN301 has seamless boot enabled. With MPC split enabled
at the same time, system will hang.
[How]
Revert MPC split policy back to "MPC_SPLIT_AVOID". Since we have
ODM combine enabled on DCN301, pipe split is not necessary here.
Signed-off-by: Zhan Liu <zhan.liu@amd.com>
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 33569ef3c7 ]
It is an unused wrapper forcing kmalloc allocation for registering
nosave regions. Also, rename __register_nosave_region() to
register_nosave_region() now that there is no need for disambiguation.
Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Reviewed-by: Cezary Rojewski <cezary.rojewski@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c74ead223d ]
Currently, on EEE capable platforms, if EEE SW timer is used, the SW
timer cause 1 wakeup/s even if the TX has successfully entered EEE.
Remove this unnecessary wakeup by only calling mod_timer() if we
haven't successfully entered EEE.
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 62afb379a0 ]
According to the comment in check_fw_ready() we should not check the
IOP1_READY field in register SCRATCH_PAD_1 for 8008 or 8009 controllers.
However we check this very field in process_oq() for processing the highest
index interrupt vector. The highest interrupt vector is checked as the FW
is programmed to signal fatal errors through this irq.
Change that function to not check IOP1_READY for those mentioned
controllers, but do check ILA_READY in both cases.
The reason I assume that this was not hit earlier was because we always
allocated 64 MSI(X), and just did not pass the vector index check in
process_oq(), i.e. the handler never ran for vector index 63.
Link: https://lore.kernel.org/r/1642508105-95432-1-git-send-email-john.garry@huawei.com
Tested-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Reviewed-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
