[ Upstream commit 35594bc7ce ]
Before suspending, mtk-eint would set the interrupt mask to the
one in wake_mask. However, some of these interrupts may not have a
corresponding interrupt handler, or the interrupt may be disabled.
On resume, the eint irq handler would trigger nevertheless,
and irq/pm.c:irq_pm_check_wakeup would be called, which would
try to call irq_disable. However, if the interrupt is not enabled
(irqd_irq_disabled(&desc->irq_data) is true), the call does nothing,
and the interrupt is left enabled in the eint driver.
Especially for level-sensitive interrupts, this will lead to an
interrupt storm on resume.
If we detect that an interrupt is only in wake_mask, but not in
cur_mask, we can just mask it out immediately (as mtk_eint_resume
would do anyway at a later stage in the resume sequence, when
restoring cur_mask).
Fixes: bf22ff45be ("genirq: Avoid unnecessary low level irq function calls")
Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Acked-by: Sean Wang <sean.wang@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0a95fc733d ]
There's a new ALPS touchpad/pointstick combo device that requires
MT_CLS_WIN_8_DUAL to make its pointsitck work as a mouse.
The device can be found on HP ZBook 17 G5.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 81c7ed296d ]
A kernel which boots in 5-level paging mode crashes in a small percentage
of cases if KASLR is enabled.
This issue was tracked down to the case when the kernel image unpacks in a
way that it crosses an 1G boundary. The crash is caused by an overrun of
the PMD page table in __startup_64() and corruption of P4D page table
allocated next to it. This particular issue is not visible with 4-level
paging as P4D page tables are not used.
But the P4D and the PUD calculation have similar problems.
The PMD index calculation is wrong due to operator precedence, which fails
to confine the PMDs in the PMD array on wrap around.
The P4D calculation for 5-level paging and the PUD calculation calculate
the first index correctly, but then blindly increment it which causes the
same issue when a kernel image is located across a 512G and for 5-level
paging across a 46T boundary.
This wrap around mishandling was introduced when these parts moved from
assembly to C.
Restore it to the correct behaviour.
Fixes: c88d71508e ("x86/boot/64: Rewrite startup_64() in C")
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Borislav Petkov <bp@alien8.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20190620112345.28833-1-kirill.shutemov@linux.intel.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2eba4e640b ]
DM verity should also use DMERR_LIMIT to limit repeat data block
corruption messages.
Signed-off-by: Milan Broz <gmazyland@gmail.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a065192655 ]
For the first call to realloc_argv() in dm_split_args(), old_argv is
NULL and size is zero. Then memcpy is called, with the NULL old_argv
as the source argument and a zero size argument. AFAIK, this is
undefined behavior and generates the following warning when compiled
with UBSAN on ppc64le:
In file included from ./arch/powerpc/include/asm/paca.h:19,
from ./arch/powerpc/include/asm/current.h:16,
from ./include/linux/sched.h:12,
from ./include/linux/kthread.h:6,
from drivers/md/dm-core.h:12,
from drivers/md/dm-table.c:8:
In function 'memcpy',
inlined from 'realloc_argv' at drivers/md/dm-table.c:565:3,
inlined from 'dm_split_args' at drivers/md/dm-table.c:588:9:
./include/linux/string.h:345:9: error: argument 2 null where non-null expected [-Werror=nonnull]
return __builtin_memcpy(p, q, size);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/md/dm-table.c: In function 'dm_split_args':
./include/linux/string.h:345:9: note: in a call to built-in function '__builtin_memcpy'
Signed-off-by: Jerome Marchand <jmarchan@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6dbc6e6f58 ]
Currently probing of the mcp23s08 results in an error message
"detected irqchip that is shared with multiple gpiochips:
please fix the driver"
This is due to the following:
Call to mcp23s08_irqchip_setup() with call hierarchy:
mcp23s08_irqchip_setup()
gpiochip_irqchip_add_nested()
gpiochip_irqchip_add_key()
gpiochip_set_irq_hooks()
Call to devm_gpiochip_add_data() with call hierarchy:
devm_gpiochip_add_data()
gpiochip_add_data_with_key()
gpiochip_add_irqchip()
gpiochip_set_irq_hooks()
The gpiochip_add_irqchip() returns immediately if there isn't a irqchip
but we added a irqchip due to the previous mcp23s08_irqchip_setup()
call. So it calls gpiochip_set_irq_hooks() a second time.
Fix this by moving the call to devm_gpiochip_add_data before
the call to mcp23s08_irqchip_setup
Fixes: 02e389e63e ("pinctrl: mcp23s08: fix irq setup order")
Suggested-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Phil Reid <preid@electromag.com.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8ac8a01092 ]
Since commit 605ad7f184 "tcp: refine TSO autosizing",
outbound throughput is dramatically reduced for some connections, as sis900
is doing TX completion within idle states only.
Make TX completion happen after every transmitted packet.
Test:
netperf
before patch:
> netperf -H remote -l -2000000 -- -s 1000000
MIGRATED TCP STREAM TEST from 0.0.0.0 () port 0 AF_INET to 95.223.112.76 () port 0 AF_INET : demo
Recv Send Send
Socket Socket Message Elapsed
Size Size Size Time Throughput
bytes bytes bytes secs. 10^6bits/sec
87380 327680 327680 253.44 0.06
after patch:
> netperf -H remote -l -10000000 -- -s 1000000
MIGRATED TCP STREAM TEST from 0.0.0.0 () port 0 AF_INET to 95.223.112.76 () port 0 AF_INET : demo
Recv Send Send
Socket Socket Message Elapsed
Size Size Size Time Throughput
bytes bytes bytes secs. 10^6bits/sec
87380 327680 327680 5.38 14.89
Thx to Dave Miller and Eric Dumazet for helpful hints
Signed-off-by: Sergej Benilov <sergej.benilov@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit aad1dcc4f0 ]
The arc4 crypto is mandatory at ppp_mppe probe time, so let's put a
softdep line, so that the corresponding module gets prepared
gracefully. Without this, a simple inclusion to initrd via dracut
failed due to the missing dependency, for example.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2e5db6eb3c ]
Certain cards in conjunction with certain switches need a little more
time for link setup that results in ethtool link test failure after
offline test. Patch adds a loop that waits for a link setup finish.
Changes in v2:
- added fixes header
Fixes: 4276e47e2d ("be2net: Add link test to list of ethtool self tests.")
Signed-off-by: Petr Oros <poros@redhat.com>
Reviewed-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 90fa9b6452 ]
Fix the cb_break_lock spinlock in afs_volume struct by initialising it when
the volume record is allocated.
Also rename the lock to cb_v_break_lock to distinguish it from the lock of
the same name in the afs_server struct.
Without this, the following trace may be observed when a volume-break
callback is received:
INFO: trying to register non-static key.
the code is fine but needs lockdep annotation.
turning off the locking correctness validator.
CPU: 2 PID: 50 Comm: kworker/2:1 Not tainted 5.2.0-rc1-fscache+ #3045
Hardware name: ASUS All Series/H97-PLUS, BIOS 2306 10/09/2014
Workqueue: afs SRXAFSCB_CallBack
Call Trace:
dump_stack+0x67/0x8e
register_lock_class+0x23b/0x421
? check_usage_forwards+0x13c/0x13c
__lock_acquire+0x89/0xf73
lock_acquire+0x13b/0x166
? afs_break_callbacks+0x1b2/0x3dd
_raw_write_lock+0x2c/0x36
? afs_break_callbacks+0x1b2/0x3dd
afs_break_callbacks+0x1b2/0x3dd
? trace_event_raw_event_afs_server+0x61/0xac
SRXAFSCB_CallBack+0x11f/0x16c
process_one_work+0x2c5/0x4ee
? worker_thread+0x234/0x2ac
worker_thread+0x1d8/0x2ac
? cancel_delayed_work_sync+0xf/0xf
kthread+0x11f/0x127
? kthread_park+0x76/0x76
ret_from_fork+0x24/0x30
Fixes: 68251f0a68 ("afs: Fix whole-volume callback handling")
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 27e23d8975 ]
omap3xxx_prm_enable_io_wakeup() is marked __init, but its caller is not, so
we get a warning with clang-8:
WARNING: vmlinux.o(.text+0x343c8): Section mismatch in reference from the function omap3xxx_prm_late_init() to the function .init.text:omap3xxx_prm_enable_io_wakeup()
The function omap3xxx_prm_late_init() references
the function __init omap3xxx_prm_enable_io_wakeup().
This is often because omap3xxx_prm_late_init lacks a __init
annotation or the annotation of omap3xxx_prm_enable_io_wakeup is wrong.
When building with gcc, omap3xxx_prm_enable_io_wakeup() is always
inlined, so we never noticed in the past.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3655802012 ]
It's a simple typo in the DNS file, which was pretty serious.
No scripts were working properly. Fix it up.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a483fcab38 ]
Starting with ACPI 6.2 bits 1 and 2 of the BGRT status field are no longer
reserved. These bits are now used to indicate if the image needs to be
rotated before being displayed.
The first device using these bits has now shown up (the GPD MicroPC) and
the reserved bits check causes us to reject the valid BGRT table on this
device.
Rather then changing the reserved bits check, allowing only the 2 new bits,
instead just completely remove it so that we do not end up with a similar
problem when more bits are added in the future.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 41b3588dba ]
If we do a clk_get() for a clock that does not exists, we have
_ti_omap4_clkctrl_xlate() return uninitialized data if no match
is found. This can be seen in some cases with SLAB_DEBUG enabled:
Unable to handle kernel paging request at virtual address 5a5a5a5a
...
clk_hw_create_clk.part.33
sysc_notifier_call
notifier_call_chain
blocking_notifier_call_chain
device_add
Let's fix this by setting a found flag only when we find a match.
Reported-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Fixes: 88a172526c ("clk: ti: add support for clkctrl clocks")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tested-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a050fa5476 ]
When we run several VMs with PCI passthrough and GICv4 enabled, not
pinning vCPUs, we will occasionally see below warnings in dmesg:
ITS queue timeout (65440 65504 480)
ITS cmd its_build_vmovp_cmd failed
The reason for the above issue is that in BUILD_SINGLE_CMD_FUNC:
1. Post the write command.
2. Release the lock.
3. Start to read GITS_CREADR to get the reader pointer.
4. Compare the reader pointer to the target pointer.
5. If reader pointer does not reach the target, sleep 1us and continue
to try.
If we have several processors running the above concurrently, other
CPUs will post write commands while the 1st CPU is waiting the
completion. So we may have below issue:
phase 1:
---rd_idx-----from_idx-----to_idx--0---------
wait 1us:
phase 2:
--------------from_idx-----to_idx--0-rd_idx--
That is the rd_idx may fly ahead of to_idx, and if in case to_idx is
near the wrap point, rd_idx will wrap around. So the below condition
will not be met even after 1s:
if (from_idx < to_idx && rd_idx >= to_idx)
There is another theoretical issue. For a slow and busy ITS, the
initial rd_idx may fall behind from_idx a lot, just as below:
---rd_idx---0--from_idx-----to_idx-----------
This will cause the wait function exit too early.
Actually, it does not make much sense to use from_idx to judge if
to_idx is wrapped, but we need a initial rd_idx when lock is still
acquired, and it can be used to judge whether to_idx is wrapped and
the current rd_idx is wrapped.
We switch to a method of calculating the delta of two adjacent reads
and accumulating it to get the sum, so that we can get the real rd_idx
from the wrapped value even when the queue is almost full.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Heyi Guo <guoheyi@huawei.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 83b44fe343 upstream.
The cacheinfo structures are alloced/freed by cpu online/offline
callbacks. Originally these were only used by sysfs to expose the
cache topology to user space. Without any in-kernel dependencies
CPUHP_AP_ONLINE_DYN was an appropriate choice.
resctrl has started using these structures to identify CPUs that
share a cache. It updates its 'domain' structures from cpu
online/offline callbacks. These depend on the cacheinfo structures
(resctrl_online_cpu()->domain_add_cpu()->get_cache_id()->
get_cpu_cacheinfo()).
These also run as CPUHP_AP_ONLINE_DYN.
Now that there is an in-kernel dependency, move the cacheinfo
work earlier so we know its done before resctrl's CPUHP_AP_ONLINE_DYN
work runs.
Fixes: 2264d9c74d ("x86/intel_rdt: Build structures for each resource based on cache topology")
Cc: <stable@vger.kernel.org>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: James Morse <james.morse@arm.com>
Link: https://lore.kernel.org/r/20190624173656.202407-1-james.morse@arm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c32cc30c05 upstream.
cpu_to_le32/le32_to_cpu is defined in include/linux/byteorder/generic.h,
which is not exported to user-space.
UAPI headers must use the ones prefixed with double-underscore.
Detected by compile-testing exported headers:
include/linux/nilfs2_ondisk.h: In function `nilfs_checkpoint_set_snapshot':
include/linux/nilfs2_ondisk.h:536:17: error: implicit declaration of function `cpu_to_le32' [-Werror=implicit-function-declaration]
cp->cp_flags = cpu_to_le32(le32_to_cpu(cp->cp_flags) | \
^
include/linux/nilfs2_ondisk.h:552:1: note: in expansion of macro `NILFS_CHECKPOINT_FNS'
NILFS_CHECKPOINT_FNS(SNAPSHOT, snapshot)
^~~~~~~~~~~~~~~~~~~~
include/linux/nilfs2_ondisk.h:536:29: error: implicit declaration of function `le32_to_cpu' [-Werror=implicit-function-declaration]
cp->cp_flags = cpu_to_le32(le32_to_cpu(cp->cp_flags) | \
^
include/linux/nilfs2_ondisk.h:552:1: note: in expansion of macro `NILFS_CHECKPOINT_FNS'
NILFS_CHECKPOINT_FNS(SNAPSHOT, snapshot)
^~~~~~~~~~~~~~~~~~~~
include/linux/nilfs2_ondisk.h: In function `nilfs_segment_usage_set_clean':
include/linux/nilfs2_ondisk.h:622:19: error: implicit declaration of function `cpu_to_le64' [-Werror=implicit-function-declaration]
su->su_lastmod = cpu_to_le64(0);
^~~~~~~~~~~
Link: http://lkml.kernel.org/r/20190605053006.14332-1-yamada.masahiro@socionext.com
Fixes: e63e88bc53 ("nilfs2: move ioctl interface and disk layout to uapi separately")
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Ryusuke Konishi <konishi.ryusuke@gmail.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Greg KH <gregkh@linuxfoundation.org>
Cc: Joe Perches <joe@perches.com>
Cc: <stable@vger.kernel.org> [4.9+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit abbe3acd7d upstream.
Thinkpad t480 laptops had some touchpad features disabled, resulting in the
loss of pinch to activities in GNOME, on wayland, and other touch gestures
being slower. This patch adds the touchpad of the t480 to the smbus_pnp_ids
whitelist to enable the extra features. In my testing this does not break
suspend (on fedora, with wayland, and GNOME, using the rc-6 kernel), while
also fixing the feature on a T480.
Signed-off-by: Cole Rogers <colerogers@disroot.org>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d17ba0f616 upstream.
Driver does not want to keep packets in Tx queue when link is lost.
But present code only reset NIC to flush them, but does not prevent
queuing new packets. Moreover reset sequence itself could generate
new packets via netconsole and NIC falls into endless reset loop.
This patch wakes Tx queue only when NIC is ready to send packets.
This is proper fix for problem addressed by commit 0f9e980bf5
("e1000e: fix cyclic resets at link up with active tx").
Signed-off-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Suggested-by: Alexander Duyck <alexander.duyck@gmail.com>
Tested-by: Joseph Yasi <joe.yasi@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Tested-by: Oleksandr Natalenko <oleksandr@redhat.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit caff422ea8 upstream.
This reverts commit 0f9e980bf5.
That change cased false-positive warning about hardware hang:
e1000e: eth0 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: Rx/Tx
IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
e1000e 0000:00:1f.6 eth0: Detected Hardware Unit Hang:
TDH <0>
TDT <1>
next_to_use <1>
next_to_clean <0>
buffer_info[next_to_clean]:
time_stamp <fffba7a7>
next_to_watch <0>
jiffies <fffbb140>
next_to_watch.status <0>
MAC Status <40080080>
PHY Status <7949>
PHY 1000BASE-T Status <0>
PHY Extended Status <3000>
PCI Status <10>
e1000e: eth0 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: Rx/Tx
Besides warning everything works fine.
Original issue will be fixed property in following patch.
Signed-off-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Reported-by: Joseph Yasi <joe.yasi@gmail.com>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=203175
Tested-by: Joseph Yasi <joe.yasi@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Tested-by: Oleksandr Natalenko <oleksandr@redhat.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fbd6b25009 upstream.
An earlier patch I sent reduced the stack usage enough to get
below the warning limit, and I could show this was safe, but with
GCC_PLUGIN_STRUCTLEAK_BYREF_ALL, it gets worse again because large stack
variables in the same function no longer overlap:
drivers/staging/rtl8712/rtl871x_ioctl_linux.c: In function 'translate_scan.isra.2':
drivers/staging/rtl8712/rtl871x_ioctl_linux.c:322:1: error: the frame size of 1200 bytes is larger than 1024 bytes [-Werror=frame-larger-than=]
Split out the largest two blocks in the affected function into two
separate functions and mark those noinline_for_stack.
Fixes: 8c5af16f79 ("staging: rtl8712: reduce stack usage")
Fixes: 81a56f6dcd ("gcc-plugins: structleak: Generalize to all variable types")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a26be06d6d upstream.
The change to mapping V4L2 to MMAL buffers 1:1 didn't handle
the condition we get with raw pixel buffers (eg YUV and RGB)
direct from the camera's stills port. That sends the pixel buffer
and then an empty buffer with the EOS flag set. The EOS buffer
wasn't handled and returned an error up the stack.
Handle the condition correctly by returning it to the component
if streaming, or returning with an error if stopping streaming.
Fixes: 9384167070 ("staging: bcm2835-camera: Remove V4L2/MMAL buffer remapping")
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Acked-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bb8e97006d upstream.
Before commit "staging: bcm2835-camera: Remove V4L2/MMAL buffer remapping"
there was a need to ensure that there were sufficient buffers supplied from
the user to cover those being sent to the VPU (always 1).
Now the buffers are linked 1:1 between MMAL and V4L2,
therefore there is no need for that check, and indeed it is wrong
as there is no need to submit all the buffers before starting streaming.
Fixes: 9384167070 ("staging: bcm2835-camera: Remove V4L2/MMAL buffer remapping")
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Acked-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8dedab2903 upstream.
The commit "staging: bcm2835-camera: Replace open-coded idr with a struct idr."
replaced an internal implementation of an idr with the standard functions
and a spinlock. idr_alloc(GFP_KERNEL) can sleep whilst calling kmem_cache_alloc
to allocate the new node, but this is not valid whilst in an atomic context
due to the spinlock.
There is no need for this to be a spinlock as a standard mutex is
sufficient.
Fixes: 950fd867c6 ("staging: bcm2835-camera: Replace open-coded idr with a struct idr.")
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Acked-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5555ebbbac upstream.
In the default event case switchdev_work is being leaked because
nothing is queued for work. Fix this by kfree'ing switchdev_work
before returning NOTIFY_DONE.
Addresses-Coverity: ("Resource leak")
Fixes: 44baaa43d7 ("staging: fsl-dpaa2/ethsw: Add Freescale DPAA2 Ethernet Switch driver")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1c2eb5b285 upstream.
The VMCI handle array has an integer overflow in
vmci_handle_arr_append_entry when it tries to expand the array. This can be
triggered from a guest, since the doorbell link hypercall doesn't impose a
limit on the number of doorbell handles that a VM can create in the
hypervisor, and these handles are stored in a handle array.
In this change, we introduce a mandatory max capacity for handle
arrays/lists to avoid excessive memory usage.
Signed-off-by: Vishnu Dasa <vdasa@vmware.com>
Reviewed-by: Adit Ranadive <aditr@vmware.com>
Reviewed-by: Jorgen Hansen <jhansen@vmware.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit feb09b2933 upstream.
This patch follows Alan Stern's recent patch:
"p54: Fix race between disconnect and firmware loading"
that overhauled carl9170 buggy firmware loading and driver
unbinding procedures.
Since the carl9170 code was adapted from p54 it uses the
same functions and is likely to have the same problem, but
it's just that the syzbot hasn't reproduce them (yet).
a summary from the changes (copied from the p54 patch):
* Call usb_driver_release_interface() rather than
device_release_driver().
* Lock udev (the interface's parent) before unbinding the
driver instead of locking udev->parent.
* During the firmware loading process, take a reference
to the USB interface instead of the USB device.
* Don't take an unnecessary reference to the device during
probe (and then don't drop it during disconnect).
and
* Make sure to prevent use-after-free bugs by explicitly
setting the driver context to NULL after signaling the
completion.
Cc: <stable@vger.kernel.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e9e08a0738 upstream.
With CONFIG_LKDTM=y and make OBJCOPY=llvm-objcopy, llvm-objcopy errors:
llvm-objcopy: error: --set-section-flags=.text conflicts with
--rename-section=.text=.rodata
Rather than support setting flags then renaming sections vs renaming
then setting flags, it's simpler to just change both at the same time
via --rename-section. Adding the load flag is required for GNU objcopy
to mark .rodata Type as PROGBITS after the rename.
This can be verified with:
$ readelf -S drivers/misc/lkdtm/rodata_objcopy.o
...
Section Headers:
[Nr] Name Type Address Offset
Size EntSize Flags Link Info Align
...
[ 1] .rodata PROGBITS 0000000000000000 00000040
0000000000000004 0000000000000000 A 0 0 4
...
Which shows that .text is now renamed .rodata, the alloc flag A is set,
the type is PROGBITS, and the section is not flagged as writeable W.
Cc: stable@vger.kernel.org
Link: https://sourceware.org/bugzilla/show_bug.cgi?id=24554
Link: https://github.com/ClangBuiltLinux/linux/issues/448
Reported-by: Nathan Chancellor <natechancellor@gmail.com>
Suggested-by: Alan Modra <amodra@gmail.com>
Suggested-by: Jordan Rupprect <rupprecht@google.com>
Suggested-by: Kees Cook <keescook@chromium.org>
Acked-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7379e6baed upstream.
The interrupt handler `pci230_interrupt()` causes a null pointer
dereference for a PCI260 card. There is no analog output subdevice for
a PCI260. The `dev->write_subdev` subdevice pointer and therefore the
`s_ao` subdevice pointer variable will be `NULL` for a PCI260. The
following call near the end of the interrupt handler results in the null
pointer dereference for a PCI260:
comedi_handle_events(dev, s_ao);
Fix it by only calling the above function if `s_ao` is valid.
Note that the other uses of `s_ao` in the calls
`pci230_handle_ao_nofifo(dev, s_ao);` and `pci230_handle_ao_fifo(dev,
s_ao);` will never be reached for a PCI260, so they are safe.
Fixes: 39064f2328 ("staging: comedi: amplc_pci230: use comedi_handle_events()")
Cc: <stable@vger.kernel.org> # v3.19+
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b8336be66d upstream.
The interrupt handler `dt282x_interrupt()` causes a null pointer
dereference for those supported boards that have no analog output
support. For these boards, `dev->write_subdev` will be `NULL` and
therefore the `s_ao` subdevice pointer variable will be `NULL`. In that
case, the following call near the end of the interrupt handler results
in a null pointer dereference:
comedi_handle_events(dev, s_ao);
Fix it by only calling the above function if `s_ao` is valid.
(There are other uses of `s_ao` by the interrupt handler that may or may
not be reached depending on values of hardware registers. Trust that
they are reliable for now.)
Note:
commit 4f6f009b20 ("staging: comedi: dt282x: use comedi_handle_events()")
propagates an earlier error from
commit f21c74fa4c ("staging: comedi: dt282x: use cfc_handle_events()").
Fixes: 4f6f009b20 ("staging: comedi: dt282x: use comedi_handle_events()")
Cc: <stable@vger.kernel.org> # v3.19+
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2681795b5e upstream.
Writing 4CC commands with tps6598x_write_4cc() already has
a pointer arg, don't reference it when using as arg to
tps6598x_block_write(). Correcting this enforces the constness
of the pointer to propagate to tps6598x_block_write(), so add
the const qualifier there to avoid the warning.
Fixes: 0a4c005bd1 ("usb: typec: driver for TI TPS6598x USB Power Delivery controllers")
Signed-off-by: Nikolaus Voss <nikolaus.voss@loewensteinmedical.de>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b2357839c5 upstream.
The old commit 6e4b74e469 ("usb: renesas: fix scheduling in atomic
context bug") fixed an atomic issue by using workqueue for the shdmac
dmaengine driver. However, this has a potential race condition issue
between the work pending and usbhsg_ep_free_request() in gadget mode.
When usbhsg_ep_free_request() is called while pending the queue,
since the work_struct will be freed and then the work handler is
called, kernel panic happens on process_one_work().
To fix the issue, if we could call cancel_work_sync() at somewhere
before the free request, it could be easy. However,
the usbhsg_ep_free_request() is called on atomic (e.g. f_ncm driver
calls free request via gether_disconnect()).
For now, almost all users are having "USB-DMAC" and the DMAengine
driver can be used on atomic. So, this patch adds a workaround for
a race condition to call the DMAengine APIs without the workqueue.
This means we still have TODO on shdmac environment (SH7724), but
since it doesn't have SMP, the race condition might not happen.
Fixes: ab330cf388 ("usb: renesas_usbhs: add support for USB-DMAC")
Cc: <stable@vger.kernel.org> # v4.1+
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dfc4fdebc5 upstream.
Use a 10000us AHB idle timeout in dwc2_core_reset() and make it
consistent with the other "wait for AHB master IDLE state" ocurrences.
This fixes a problem for me where dwc2 would not want to initialize when
updating to 4.19 on a MIPS Lantiq VRX200 SoC. dwc2 worked fine with
4.14.
Testing on my board shows that it takes 180us until AHB master IDLE
state is signalled. The very old vendor driver for this SoC (ifxhcd)
used a 1 second timeout.
Use the same timeout that is used everywhere when polling for
GRSTCTL_AHBIDLE instead of using a timeout that "works for one board"
(180us in my case) to have consistent behavior across the dwc2 driver.
Cc: linux-stable <stable@vger.kernel.org> # 4.19+
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d29fcf7078 upstream.
On spin lock release in rx_submit, gether_disconnect get a chance to
run, it makes port_usb NULL, rx_submit access NULL port USB, hence null
pointer crash.
Fixed by releasing the lock in rx_submit after port_usb is used.
Fixes: 2b3d942c48 ("usb ethernet gadget: split out network core")
Cc: <stable@vger.kernel.org>
Signed-off-by: Kiruthika Varadarajan <Kiruthika.Varadarajan@harman.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6e41e2257f upstream.
The syzbot fuzzer found a bug in the p54 USB wireless driver. The
issue involves a race between disconnect and the firmware-loader
callback routine, and it has several aspects.
One big problem is that when the firmware can't be loaded, the
callback routine tries to unbind the driver from the USB _device_ (by
calling device_release_driver) instead of from the USB _interface_ to
which it is actually bound (by calling usb_driver_release_interface).
The race involves access to the private data structure. The driver's
disconnect handler waits for a completion that is signalled by the
firmware-loader callback routine. As soon as the completion is
signalled, you have to assume that the private data structure may have
been deallocated by the disconnect handler -- even if the firmware was
loaded without errors. However, the callback routine does access the
private data several times after that point.
Another problem is that, in order to ensure that the USB device
structure hasn't been freed when the callback routine runs, the driver
takes a reference to it. This isn't good enough any more, because now
that the callback routine calls usb_driver_release_interface, it has
to ensure that the interface structure hasn't been freed.
Finally, the driver takes an unnecessary reference to the USB device
structure in the probe function and drops the reference in the
disconnect handler. This extra reference doesn't accomplish anything,
because the USB core already guarantees that a device structure won't
be deallocated while a driver is still bound to any of its interfaces.
To fix these problems, this patch makes the following changes:
Call usb_driver_release_interface() rather than
device_release_driver().
Don't signal the completion until after the important
information has been copied out of the private data structure,
and don't refer to the private data at all thereafter.
Lock udev (the interface's parent) before unbinding the driver
instead of locking udev->parent.
During the firmware loading process, take a reference to the
USB interface instead of the USB device.
Don't take an unnecessary reference to the device during probe
(and then don't drop it during disconnect).
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: syzbot+200d4bb11b23d929335f@syzkaller.appspotmail.com
CC: <stable@vger.kernel.org>
Acked-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3f2640ed7b upstream.
This reverts commit 2e9fe53910.
Reading LSR unconditionally but processing the error flags only if
UART_IIR_RDI bit was set before in IIR may lead to a loss of transmission
error information on UARTs where the transmission error flags are cleared
by a read of LSR. Information are lost in case an error is detected right
before the read of LSR while processing e.g. an UART_IIR_THRI interrupt.
Signed-off-by: Oliver Barta <o.barta89@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Fixes: 2e9fe53910 ("serial: 8250: Don't service RX FIFO if interrupts are disabled")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
