This change affects to the OSD driver, drivers/amlogic/media/osd/osd_fb.c, to enable
soft cursor instead of OSD cursor.
Signed-off-by: Dongjin Kim <tobetter@gmail.com>
Change-Id: Ic4af0037579b5b62c4df7b29a05d1cceec0cd9cf
This patch adds to new attribute 'pwm1_enable' to change the fan speed
control method as documented in 'Documentation/hwmon/sysfs-interface'.
Signed-off-by: Dongjin Kim <tobetter@gmail.com>
Change-Id: I19094d60e928d6c3ce226d319e75a35ecbd3ae52
The existing force64b routine might not work properly under specific
conditions. This patch fixes that bug of 64 bits per word and forces
use that option. It will improve SPI performance significantly.
Signed-off-by: Deokgyu Yang <secugyu@gmail.com>
Change-Id: I85a58d425303ea1765b7b83ee5dd5f0a7f4203fc
- The PWM's configuration is difference between the n2 and c4. So
separate configuration and placed to the device tree overlays.
Change-Id: Ia870ce6ea4404c8bc7028ae7f1cc72174406ed27
[1] GPIOAO_2 is tied to control USB 2.0 host power
[2] USB 3.0 PHY must be disabled exclusively for PCIe.
Signed-off-by: Dongjin Kim <tobetter@gmail.com>
Change-Id: I340ca69f6da448a441ed75c506ea569947a581c4
With some specific monitors those pixel clock is under 300MHz,
unstable display operation may occur.
So, default timing for 2560x1600p60hz is set as following.
Detailed mode: Clock 268.500 MHz, 641 mm x 401 mm
2560 2608 2640 2720 ( 48 32 80)
1600 1602 1608 1646 ( 2 6 38)
+hsync -vsync
VertFreq: 59.972 Hz, HorFreq: 98.713 kHz
Change-Id: I7812a491b5d81379cd4568223d478909ecd882c4
[ Upstream commit 96e97bc07e ]
napi_disable() makes sure to set the NAPI_STATE_NPSVC bit to prevent
netpoll from accessing rings before init is complete. However, the
same is not done for fresh napi instances in netif_napi_add(),
even though we expect NAPI instances to be added as disabled.
This causes crashes during driver reconfiguration (enabling XDP,
changing the channel count) - if there is any printk() after
netif_napi_add() but before napi_enable().
To ensure memory ordering is correct we need to use RCU accessors.
Reported-by: Rob Sherwood <rsher@fb.com>
Fixes: 2d8bff1269 ("netpoll: Close race condition between poll_one_napi and napi_disable")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3106ecb43a ]
With disabling bh in the whole sctp_get_port_local(), when
snum == 0 and too many ports have been used, the do-while
loop will take the cpu for a long time and cause cpu stuck:
[ ] watchdog: BUG: soft lockup - CPU#11 stuck for 22s!
[ ] RIP: 0010:native_queued_spin_lock_slowpath+0x4de/0x940
[ ] Call Trace:
[ ] _raw_spin_lock+0xc1/0xd0
[ ] sctp_get_port_local+0x527/0x650 [sctp]
[ ] sctp_do_bind+0x208/0x5e0 [sctp]
[ ] sctp_autobind+0x165/0x1e0 [sctp]
[ ] sctp_connect_new_asoc+0x355/0x480 [sctp]
[ ] __sctp_connect+0x360/0xb10 [sctp]
There's no need to disable bh in the whole function of
sctp_get_port_local. So fix this cpu stuck by removing
local_bh_disable() called at the beginning, and using
spin_lock_bh() instead.
The same thing was actually done for inet_csk_get_port() in
Commit ea8add2b19 ("tcp/dccp: better use of ephemeral
ports in bind()").
Thanks to Marcelo for pointing the buggy code out.
v1->v2:
- use cond_resched() to yield cpu to other tasks if needed,
as Eric noticed.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Reported-by: Ying Xu <yinxu@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d3b990b7f3 ]
This patch fixes two main problems seen when removing NetLabel
mappings: memory leaks and potentially extra audit noise.
The memory leaks are caused by not properly free'ing the mapping's
address selector struct when free'ing the entire entry as well as
not properly cleaning up a temporary mapping entry when adding new
address selectors to an existing entry. This patch fixes both these
problems such that kmemleak reports no NetLabel associated leaks
after running the SELinux test suite.
The potentially extra audit noise was caused by the auditing code in
netlbl_domhsh_remove_entry() being called regardless of the entry's
validity. If another thread had already marked the entry as invalid,
but not removed/free'd it from the list of mappings, then it was
possible that an additional mapping removal audit record would be
generated. This patch fixes this by returning early from the removal
function when the entry was previously marked invalid. This change
also had the side benefit of improving the code by decreasing the
indentation level of large chunk of code by one (accounting for most
of the diffstat).
Fixes: 63c4168874 ("netlabel: Add network address selectors to the NetLabel/LSM domain mapping")
Reported-by: Stephen Smalley <stephen.smalley.work@gmail.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cbedcb044e upstream.
On machines with much memory (> 2 TByte) and log_mtts_per_seg == 0, a
max_order of 31 will be passed to mlx_buddy_init(), which results in
s = BITS_TO_LONGS(1 << 31) becoming a negative value, leading to
kvmalloc_array() failure when it is converted to size_t.
mlx4_core 0000:b1:00.0: Failed to initialize memory region table, aborting
mlx4_core: probe of 0000:b1:00.0 failed with error -12
Fix this issue by changing the left shifting operand from a signed literal to
an unsigned one.
Fixes: 225c7b1fee ("IB/mlx4: Add a driver Mellanox ConnectX InfiniBand adapters")
Signed-off-by: Shung-Hsi Yu <shung-hsi.yu@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d3a84a8d0d ]
The basic permission bits (protection bits in AmigaOS) have been broken
in Linux' AFFS - it would only set bits, but never delete them.
Also, contrary to the documentation, the Archived bit was not handled.
Let's fix this for good, and set the bits such that Linux and classic
AmigaOS can coexist in the most peaceful manner.
Also, update the documentation to represent the current state of things.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable@vger.kernel.org
Signed-off-by: Max Staudt <max@enpas.org>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Tascam FE-8 is known to support communication by asynchronous transaction
only. The support can be implemented in userspace application and
snd-firewire-ctl-services project has the support. However, ALSA
firewire-tascam driver is bound to the model.
This commit changes device entries so that the model is excluded. In a
commit 53b3ffee78 ("ALSA: firewire-tascam: change device probing
processing"), I addressed to the concern that version field in
configuration differs depending on installed firmware. However, as long
as I checked, the version number is fixed. It's safe to return version
number back to modalias.
Fixes: 53b3ffee78 ("ALSA: firewire-tascam: change device probing processing")
Cc: <stable@vger.kernel.org> # 4.4+
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20200823075537.56255-1-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>
