PD#TV-4365
Problem:
USB keyboard not recognized after reboot repeatedly.
Solution:
Reset the reset_FS_LS_Clock_Divider bit of the usb phy.
Verify:
tl1
Change-Id: I0f4bf35be04d3aff1094bf55641348ccaca072e4
Signed-off-by: he.he <he.he@amlogic.com>
PD#SWPL-5664
Problem:
for netflix 23.97fps non-tunnle playback 3:2 patten broken so many times
Solution:
reuse initial phase that Tim use in amazon
Verify:
verify by u212
Change-Id: I5d988e1c3a3dbf1bb728f55a921e8b8fb6990985
Signed-off-by: shuanglong.wang <shuanglong.wang@amlogic.com>
PD#SWPL-5664
Problem:
pcr not paused when netflix video non-tunnel mode pause
Solution:
do not compensation when diff between omxpts and pcr too large
Because when paused, continous compensation will lead diff
beween omxpts and pcr will alway inside pcr adjust threshold,
and pcr not set again, then pcr will increase
Verify:
verify by nts
Change-Id: Ib2acea35758d161d1e9db53dd6ff369ba7973351
Signed-off-by: shuanglong.wang <shuanglong.wang@amlogic.com>
PD#SWPL-5664
Problem:
pcr is probably adjust when test AL1 eyepatch test case
Solution:
the time is not accurate when check pcr and omx_pts differ, because
omx_pts is used the value that be set, but pcr is current. Here add
compensation for omx_pts
Verify:
verify by nts
Change-Id: I3e0f6f006fd79cf7cac4148fd18da72111a333c7
Signed-off-by: shuanglong.wang <shuanglong.wang@amlogic.com>
PD#SWPL-7656
Problem:
crash when there is cpu boot fail in hmp
Solution:
fix crash when there is cpu boot fail in hmp
Verify:
W400
Change-Id: I0153975593adb0bfcbc3c3bd6543f0fb2e6bf2e0
Signed-off-by: Jianxin Pan <jianxin.pan@amlogic.com>
PD#SWPL-7181
Problem:
switch to high-speed from hs200 failed for resume process.
Solution:
set tx_delay as 0 for legacy mode.
clear cfg_cmd_setup
Verify:
verify by TL1
Change-Id: I5dbb1bbc391da864464bf137837a2b0f54ccda42
Signed-off-by: Long Yu <long.yu@amlogic.com>
Signed-off-by: Luan Yuan <luan.yuan@amlogic.com>
PD#SWPL-7960
Problem:
There is no min ddr bandwidth data
Solution:
Add this value in sysfs
Verify:
p212
Change-Id: I9d90476d30c0ca7789046d8d205f0802de2b4acf
Signed-off-by: Tao Zeng <tao.zeng@amlogic.com>
PD#SWPL-7798
Problem:
Crashed when audio resample setting params
are invalid.
Solution:
Add check method if the params is invalid.
Verify:
Tl1.
Change-Id: I1e0396be8d401c0a49ff0de9fd7f160f0c8133ca
Signed-off-by: Shuai Li <shuai.li@amlogic.com>
PD#SWPL-6865
Problem:
ddr bandwidth measure is not supported on sm1
Solution:
1. Add port description and support for it
2. Record max/average bandwidth support;
3. Support up to 60 continue bandwidth sample
4. Fix bit mismatch of dmc monitor for sm1/tl1.
Verify:
sm1
Change-Id: I0b42db8214099b9cd6d1c3f00174dc65eebfc030
Signed-off-by: Tao Zeng <tao.zeng@amlogic.com>
Signed-off-by: Luan Yuan <luan.yuan@amlogic.com>
PD#SWPL-7765
Problem:
g12b revb efuse not correct
Solution:
set tx_amp with chipid to work around
Verify:
verify on g12b skt board
Change-Id: Id1babce231d866293e4de52685834834a4b65227
Signed-off-by: Zhuo Wang <zhuo.wang@amlogic.com>
PD#SWPL-6937
Problem:
1.get lefttime error by 'cat sys/class/watchdog/watchdog0/timeleft' cmd.
2.if DTS is configured to feed watchdog by Android, the system will
restart automatically after wake up.
Solution:
1.modify the code to get time.
2.when the system wakes up, first judge whether the watchdog runs,
and then decide whether to start the watchdog.
Verify:
test pass on u200
Change-Id: If64888ffdd5651e8cfcace5ea0d0da31641bb397
Signed-off-by: Yingyuan Zhu <yingyuan.zhu@amlogic.com>
PD#SWPL-5475
Problem:
need to add interface of HDR Prime SL driver
Solution:
add interface of HDR Prime SL driver
Verify:
U212
Change-Id: If0e62b74ccbaa4ede490e7a9896d9f5915480d6f
Signed-off-by: Yi Zhou <yi.zhou@amlogic.com>
PD#OTT-2524
Problem:
enable sdr2hdr function, uboot logo have color change
Solution:
match uboot sdr2hdr function
Verify:
verify on G12A
Change-Id: I160cd6141d09a385d299ca96a89eb1ebf09c86e8
Signed-off-by: MingLiang Dong <mingliang.dong@amlogic.com>
PD#SWPL-6969
Problem:
For some historical reason, aml-uart is configured as the earlycon
name in uboot, which is not recognized by 4.9 kernel
Solution:
support aml-uart as the name for earlycon
Verify:
Ampere
Change-Id: I01427f2d512c0bf1972dd545dc71570919c5bc07
Signed-off-by: Jiamin Ma <jiamin.ma@amlogic.com>
PD#OTT-3244
Problem:
When vd layer state is on_pending, calling enable videolayer
function will overwrite the state. Then it will not enable video
layer really.
Solution:
Add the judgement to check if the state is on_pending.
Verify:
verified on W400
Change-Id: I0513a6610fdb108bec05858c7f6c7976be5e7edb
Signed-off-by: Brian Zhu <brian.zhu@amlogic.com>
PD#SWPL-7302
Problem:
sm1 green screen when play videos
Solution:
add chip support
Verify:
s905D3
Change-Id: I50c0a9f889d72b65157a973bfe1df8dce10db64a
Signed-off-by: Bencheng Jing <bencheng.jing@amlogic.com>
PD#TV-2802
Problem:
The image is stuck or blackscrean for a few seconds
when the DTV stream is replayed.
Solution:
when audio pts and video pts discontinue, then
adjust the pcr source clock.
Verify:
X301
Change-Id: Id0a74e2d4106a30b426bfa7a4faa70451db9b79e
Signed-off-by: Xiaoming Sui <xiaoming.sui@amlogic.com>
PD#SWPL-4551
Problem:
ImagePlayer cannot play picture
Solution:
add picdec dev node for u200 u211 u212 w400
Verify:
franklin
Change-Id: I35cc28e2ab06367f33a7326ce671b1ee461e6fb1
Signed-off-by: xi an <an.xi@amlogic.com>
Signed-off-by: Luan Yuan <luan.yuan@amlogic.com>
PD#SWPL-6586
Problem:
Android P trunk can not compile 64bit kernel
Android P vendor size is not enough,
64bit kernel and isp so etc ,
the size exceeds 256M
Solution:
change vendor size from 256M into 320M
Verify:
galilei
Change-Id: Icc7b3d7c8d56f5c361acf9722bba6422b8dc3af2
Signed-off-by: Liang Ji <liang.ji@amlogic.com>
Signed-off-by: Luan Yuan <luan.yuan@amlogic.com>
PD#SWPL-5002
Problem:
TL1 need to support defendkey secure upgrade check
Solution:
1.modify the way of get random
Verify:
TL1 skt board verify pass
Change-Id: I76b29800de787c5e5b18e023d84c1161c9b1643a
Signed-off-by: Zhongfu Luo <zhongfu.luo@amlogic.com>
PD#SWPL-6896
Problem:
In the HF1-31 Iter 03 test, the Rx EDID's max tmds clock is 600MHz,
and it doesn't claim that it supports Y420 modes. But
echo 2160p60hz,420,8bit > /sys/class/amhdmitx/amhdmitx0/valid_mode
'cat valid_mode' will get 1.
Solution:
Add Y420 8bit check
Verify:
G12/U212
Change-Id: I0a128eb33aeb2b4bcbf253eff49e9c5186386af1
Signed-off-by: Zongdong Jiao <zongdong.jiao@amlogic.com>
PD#SWPL-4551
Problem:
ImagePlayer cannot play picture
Solution:
add picdec dev node for u200 u211 u212 w400
Verify:
franklin
Change-Id: I35cc28e2ab06367f33a7326ce671b1ee461e6fb1
Signed-off-by: xi an <an.xi@amlogic.com>
PD#SWPL-6694
Problem:
home button has no function in sm1-ac200
Solution:
add home button configuration in dst node
Verify:
test pass on sm1-ac200
Change-Id: I670480c6dfd7f833e737adaddbe5981d84091203
Signed-off-by: Yingyuan Zhu <yingyuan.zhu@amlogic.com>
PD#OTT-2452
Problem:
Black screen in the middle of the cut.
Solution:
add keep last frame.
Verify:
on U212
Change-Id: Ib24f066e0682c7427024a74d9bf8cc9b8a310d62
Signed-off-by: renjiang.han <renjiang.han@amlogic.com>
PD#SWPL-3730
Problem:
playback not smooth
Solution:
if p2 lookup fail, set p2 = p
Verify:
verified by x301
Change-Id: I181eae2ba40edd937df12e0925c2a55c856162ba
Signed-off-by: rongrong zhou <rongrong.zhou@amlogic.com>
PD#SWPL-6200
Problem:
emmc calibration delay set error.
Solution:
modify delay_step to 250ps.
Verify:
verify by s912.
Change-Id: I1c0e31ae6bdda8b0f105e12f3efc81b5474376d6
Signed-off-by: Nan Li <nan.li@amlogic.com>
PD#SWPL-4653
Problem:
optimize the S905Y2 power consumption
Solution:
limit CPU and GPU frequency, reduce hdmi tx consumption
Verify:
test pass on u221
Change-Id: I1d95068f8beb5616c9aeea91122b5233e479db8b
Signed-off-by: huijie.huang <huijie.huang@amlogic.com>
PD#SWPL-5404
Problem:
emmc report data crc error in hs200 busmode
Solution:
set hs200 co_phase to 2 and did not reset the
hs200 co_phase and tx_phase when adjust tuning is
find the error point in sm1
Verify:
verify pass on sm1_s905d3_ac200
Change-Id: I56aa8eb666fb55641db75878a3488f66c721bd6d
Signed-off-by: ruixuan.li <ruixuan.li@amlogic.com>
PD#SWPL-5404
Problem:
sm1 usb fixdiv mode set adjust cause error
Solution:
disable emmc calc_f in dtsi.
Verify:
test pass on sm1 ac200
Change-Id: I4459bf4faa2141a9e684b1e5bb95fb806eecbbfa
Signed-off-by: ruixuan.li <ruixuan.li@amlogic.com>
PD#SWPL-2634
Problem:
eyetest mode is a little unstable
Solution:
adjust the tuning mode of the fixed adj
Verify:
R311
Change-Id: I6112e0078bf013d2a4cfe4ff04210f1d15e3439d
Signed-off-by: long yu <long.yu@amlogic.com>
PD#SWPL-6810
Problem:
android version, no sound for spk
ad82584 is mute in default.
Solution:
un-mute ad82584, and add delay for de-pop
Verify:
ac200
Change-Id: Id78eb77b5e1a0ebed0a16a9b97992c6a07f78cde
Signed-off-by: Xing Wang <xing.wang@amlogic.com>
Signed-off-by: Jian Xu <jian.xu@amlogic.com>
PD#SWPL-3750
Problem:
when debug on, too more log
Solution:
delete
Verify:
verified on android p
Change-Id: Iabaaa4fa205da5453a303c98bce8b71b55c5f77b
Signed-off-by: Yong Qin <yong.qin@amlogic.com>
PD#SWPL-5292
Problem:
g12b-revB, some u disk amldevread test failed.
Solution:
Changing the register 0x54 to 0x2a, enabled the hs rx idle noise filter,
and the abnormal u-disk has no problem in the amldevread test.
Verify:
g12b revB
Change-Id: Ibbf924c93d193d7e40c4d8121a4616a8d1caeaaa
Signed-off-by: he.he <he.he@amlogic.com>
