modify the rk808 max steps for increase voltage of Buck1/2,
equal 25mv.
Change-Id: Ic6c016e99ce67f5773d5f5df0b65fa1de10f557a
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
New driver only support DRP mode without swap function.
Swap function will be added in later.
Change-Id: I7e0c2c424def069d4be78c3bc8f704c3f7e5be48
Signed-off-by: Zain Wang <wzz@rock-chips.com>
CACHE_L2X0/TWD/ARM_GLOBAL_TIMER are only available on Cortex-A9.
DW_APB_TIMER_OF only use on rk3066a.
Change-Id: Ied2f49b5d308e961ce5af72eb577aac23e3eb890
Signed-off-by: Tao Huang <huangtao@rock-chips.com>
256KB alignment is not work for (textofs & 0xf0000) > 0x40000.
Change to 1MB.
Change-Id: I9803b22d7d64a244842dcc811e47e214d247fc0c
Signed-off-by: Tao Huang <huangtao@rock-chips.com>
Add simple read only driver for the OTP (One Time Programmable)
memory found on Rockchip SoCs.
Change-Id: I01c63dcacaf471ed7d06e0e8263a14e29af7fb0e
Signed-off-by: Finley Xiao <finley.xiao@rock-chips.com>
The main description for rk3308b is as follows:
- Old iomux multiplexing extension;
- GRF_SOC_CON5 register add some bits;
- Newly added GRF_SOC_CON13/15 register.
Change-Id: I94bfcae5387aceae14895f1cafa0bfea51bf8b63
Signed-off-by: David Wu <david.wu@rock-chips.com>
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
The most pins of rk3308 are 2bits iomux, but the banks's register
width is 0x8.
Change-Id: I3305810b3f75febd6ec7a933b65e3c9d50f003dd
Signed-off-by: David Wu <david.wu@rock-chips.com>
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
According to the dwc2 programmer's guide v3.10a, in '2.1.3.2 Dedicated
FIFO Mode with No Thresholding', it suggested that:
Device RxFIFO =
- Scatter/Gather DMA mode:
(4 * number of control endpoints + 6) + ((largest USB packet used / 4) +
1 for status information) + (2 * number of OUT endpoints) + 1 for Global NAK
on rockchip platforms:
(4 * 1 + 6) + ((1024 / 4) + 1) + (2 * 6) + 1 = 280
- Slave or Buffer DMA mode:
(5 * number of control endpoints + 8) + ((largest USB packet used / 4) +
1 for status information) + (2 * number of OUT endpoints) + 1 for Global NAK
on rockchip platforms:
(5 * 1 + 8) + ((1024 / 4) + 1) + (2 * 6) + 1 = 283
Device IN Endpoint TxFIFO =
The TxFIFO must equal at least one MaxPacketSize (MPS).
In addition to RxFIFO and TxFIFOs, refer to dwc2 databook v3.10a,
'Figure 2-13 Device Mode FIFO Address Mapping and AHB FIFO Access Mapping
(Dedicated FIFO)', it required that when the device is operating in non
Scatter Gather Internal DMA mode, the last locations of the SPRAM are used
to store the DMAADDR values for each Endpoint (1 location per endpoint).
When the device is operating in Scatter Gather mode, then the last locations
of the SPRAM store the Base Descriptor address, Current Descriptor address,
Current Buffer address, and status quadlet information for each endpoint
direction (4 locations per Endpoint). If an Endpoint is bidirectional , then
4 locations will be used for IN, and another 4 for OUT).
Considering that the total FIFO size of dwc2 otg is 0x3cc (972),
and we must reserve (4 * 13) = 52 locations for all Endpoints.
So reconfig dwc2 device fifo size as follows:
Device RxFIFO = 280
Device IN Endpoint TxFIFO
- FIFO #0 = (64 / 4) = 16 (Assuming this is used for EP0)
- FIFO #1 = (1024/4) = 256 (Assuming this is used for Isochronous)
- FIFO #2 = (512/4) = 128
- FIFO #3 = (512/4) = 128
- FIFO #4 = (256/4) = 64
- FIFO #5 = (128/4) = 32
- FIFO #6 = (64/4) = 16
After reconfig the dwc2 device fifo size, test mtp write on rockchip
platform (PC -> rockchip platform) on rk312x/rk3326/px30/rk3288 evb,
when mask the 'vfs_write' in f_mtp.c, the writing data rate can be
increased from 16MBps ~ 20MBps to 30MBps ~ 36MBps on different kinds
of rockchip evbs.
Change-Id: Icdf8a5dd95f96d174233e4ffc765c9a982b9f0b6
Signed-off-by: William Wu <william.wu@rock-chips.com>
Single entry is for target voltage and three entries are for
<target min max> voltages. Change cpu opp-microvolt form one entry to
three entries and set maximum acceptable voltage to a high value so that
regulator device can supply multiple consumers at the same time.
Fixes: 16e9353f89 ("arm: dts: rockchip: Change cpu opp-microvolt form one entry to three")
Change-Id: I96e5f87f2945e63e8f4a073fa0292f001830b13c
Signed-off-by: Finley Xiao <finley.xiao@rock-chips.com>
The vdd_logic is a pwm regulator. Since '#pwm-cells = <2>', there
is not polarity invert support by pwm driver, so we have to add
property 'pwm-dutycycle-range = <100 0>' to support polarity invert
by pwm regulator driver itself.
Change-Id: Ie5d2cda67ce19dc792f96263836bab658d385681
Signed-off-by: Joseph Chen <chenjh@rock-chips.com>
Add supports-emmc for emmc; supports-sd for sdcard; supports-sdio for
wifi.
Change-Id: I13d3918f41f63ed9b27e9969e6f89d1006c9d45c
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
Serial Flash controller is used to control the data
transfer between this SoC and a serial nor or nand
flash device.
Change-Id: Ibe7c8c4a11410287c34c1a7dc5b232b330ee6751
Signed-off-by: Randy Li <randy.li@rock-chips.com>
The vpu qos registers need to save and restore when reset.
Change-Id: I649cf4a360842ad1abb06c35a6fd8d3868fbf706
Signed-off-by: Finley Xiao <finley.xiao@rock-chips.com>
According to the actual schematic designed by kylin board, update and
rename the regulators for rk808 node information.
Especially gpu regulator voltage, the schematic didn't have this
regulator, this regulaor should be applied by cpu regulator since the
cpu/gpu/ddr are belong to the same logic power supply.
Change-Id: I39e4cf18969391da396cc775f8660701e42977bd
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
As the vpu needed handle the power domain for reset function, this patch
supported the vpu domain for rk3036 Socs.
Change-Id: I67ad6085e2eb9a213c364d58713f02cc78ce6849
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
rk3036 doesn't support vdd_arm power supply off when system suspend.
Change-Id: I46bd8a7c2b672be30d8106b867275e8ba7d77e54
Signed-off-by: Joseph Chen <chenjh@rock-chips.com>
As the HDMI-audio/codec will cause the hang on bootup, the root
cause that kylin get the invalid master clock from i2s.
$cat/sys/kernel/debug/clk/clk_summary
..
i2s_pre 0 0 0 0 0
sclk_i2s 0 0 0 0 0
i2s_clkout 0 0 0 0 0
Since i2s clock selects io input clock by default, but the hardware
didn't supply the clock.
This patch will fix the sclk_i2s's parent on i2s_frac.
As following:
$cat/sys/kernel/debug/clk/clk_summary
..
i2s_src 1 1 594000000 0 0
i2s_frac 1 1 22579200 0 0
i2s_pre 2 2 22579200 0 0
sclk_i2s 1 1 22579200 0 0
As far, the audio can work with aplay/record on kylin.dts
Says:
(aplay /dev/urandom)
/* recording */
arecord -f cd -d 10 /tmp/audio.wav
/* playback */
aplay /tmp/audio.wav
Change-Id: I73534a0d763eb02fb55e000ce068d9d604bf20ed
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
As the cpu frequency is less than 816MHz, the HDMI display maybe
probably cause a flower screen as below log[0]. And Kylin used the rk3036g
series SoCs that the max cpu frequency supported the 1GHz, not 1.2GHz.
In a word, keep the cpu frequency to 1GHz for kylin board.
log[0]:
[26.498843] rk_iommu 10118300.iommu: Enable stall request timed out,
status: 0x000011
[26.528809] rk_iommu 10118300.iommu: Disable paging request timed out,
status: 0x000011
[26.598849] rk_iommu 10118300.iommu: Enable stall request timed out,
status: 0x000011
[26.607579] rockchip-vop 10118000.vop: Failed to attach iommu device
[26.614916] rockchip-vop 10118000.vop: failed to attach dma mapping, -110
..
Change-Id: I8e1d4527b649d8857a9d80a121c10935a4cd1030
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
As the emmc is supplyed power by vcc_io, that's 3.3v voltage.
the default 1.8v volatge will cause the emmc error. as the following:
[ 17.096082 ] mmcblk1: error -115 sending stop command, original cmd
response 0x900, card status 0xb00
[ 17.127022 ] mmcblk1: error -110 transferring data, sector 664720, nr
72, cmd response 0x900, card status 0xb00
Remove the mmc-ddr-1_8v to keep the default the 3.3v voltage.
Change-Id: I9e2539d63fd93e72d9febbb311fbd686c5a11d09
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
This patch supported the gpu opp table for rk3036.
The gpu clock's parent is DPLL, the default frequency is 400MHz, we need
assign 400MHz for gpu to be better working.
There is a quickly way for testing the gpu scaling frequency.
As following:
"
unset FREQS
read -a FREQS < /sys/class/devfreq/10091000.gpu/available_frequencies
RANDOM=$$$(date +%s)
while true; do
echo userspace > /sys/class/devfreq/10091000.gpu/governor
FREQ=${FREQS[$RANDOM % ${#FREQS[@]} ]}
echo GPU:Now ${FREQ}
echo ${FREQ} > /sys/class/devfreq/10091000.gpu/userspace/set_freq
sleep 1
done
"
Change-Id: Ia8eb3074e457014c497338a0a129551c51450104
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
This patch supported the cpu voltage by changed with different
frequency, otherwise we will hit the following error on bootup.
..
[ 5.031516] cpu cpu0: Failed to get cpu_reg
[ 5.047725] cpu cpu0: clk or regulater is unavailable
..
Also, remove the 408M and 600M for rk3036 board, as the pclk_hdmi's parent
on apll, the low frequency will make the pclk be bad for hdmi display.
Change-Id: Ia4aac76a08cad3a59c33cd81065f943201a23a35
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
