The other Socs also need the feature of recalced iomux, so
make it as a common interface like iomux route feature.
Change-Id: I8a58ae0af5edd497a545d3734d99c22bed177a43
Signed-off-by: David Wu <david.wu@rock-chips.com>
As vpu and rkvdec use the common idle request, if vpu enable idle request
and rkvdec is working, the rkvdec will be crash, so let them both don't
do idle request.
Change-Id: I1fe2bc99c81d3b2018e86896548514e5e8093a4a
Signed-off-by: Finley Xiao <finley.xiao@rock-chips.com>
The original setting of "max_job_runtime" is too small
that jobs are too easy to timeout and be killed.
Change-Id: I5316c2b594d94dd0b844ef9a297baa7b226c4665
Signed-off-by: chenzhen <chenzhen@rock-chips.com>
Add vsel gpio for syr827, which is PMIC_SLEEP in hardware pcb.
The driver will parse the gpio and use it to indicate the chip
work status, as the following codes:
static int fan53555_is_enabled ()
if defined vsel_gpio
gpiod_get_raw_value
else
regmap_read
Before the patch, the log shows:
CPU4: update cpu_capacity 1024
CPU4: Booted secondary processor [410fd033]
cache: parent cpu4 should not be sleeping
rk3x-i2c ff650000.i2c: timeout, ipd: 0x10, state: 1
Since cpu4 is the base core for cluster1, which need to initialize
cpufreq during boot up, finally call fan53555_is_enabled. But the
i2c is suspended at that time, can't get interrupt until timeout.
Change-Id: I301e95be3b60d2faa456759d88c06cf64c2019ca
Signed-off-by: Jianqun Xu <jay.xu@rock-chips.com>
Vop would always report post buf empty error if enable
post scale config with non-scale factor
Change-Id: Ibc3f27c674195e6467471069488f14471927f709
Signed-off-by: Mark Yao <mark.yao@rock-chips.com>
The otg_sm_work will suspend the usb2 phy immediately
if it detects disconnection from host. However, the usb2
controller(e.g. DWC2) may need to reinit registers and
reset usb core after usb disconnect, and it needs to
keep the usb2 phy stay in power on state to get utmi clk
for these usb controller operation. We don't have a good
synchronization mechanism to operate usb2 phy between
usb2 phy driver and usb2 controller driver, so we delay
4s to suspend phy if detect otg device disconnect from
host, this can make sure that usb2 controller completes
reinitialization before suspend usb2 phy.
Change-Id: I79288b8c7b141bb16e6d96d80cfee75f7558d2c0
Signed-off-by: William Wu <william.wu@rock-chips.com>
Use the same calculation as the vendor kernel to derive the escape clock
speed.
Change-Id: I7aff4dc7fa9598df164148eaf44304caad704f23
Signed-off-by: xubilv <xbl@rock-chips.com>
Requesting the HS clock from the PHY before we initialize it causes an
invalid signal to be sent out since the input clock is not yet
configured. The PHY databook suggests only asserting this signal when
performing HS transfers, so let's do that.
Change-Id: I7006f81d8c620dc84e84f99383c7b5414d6ac12d
Signed-off-by: xubilv <xbl@rock-chips.com>
It is convenient for the client to manually adjust
the value of lane rate.
Change-Id: Ic6d8c4d235eacc8cb7540d172bd69c29c2b277dd
Signed-off-by: xubilv <xbl@rock-chips.com>
The analysis of platform parameters Only need to do it once,
if this in bind function, when return -EPROBE_DEFER,
it will be executed more than once.
Change-Id: I508021f930d39e1b79e1421c4262b9e7ab501b6c
Signed-off-by: xubilv <xbl@rock-chips.com>
This flag is used as a condition for the register configuration
Change-Id: I6741063b106ae00f4f1a690abde79d76bc529e95
Signed-off-by: xubilv <xbl@rock-chips.com>
Add dts file for firefly rk3399 board to run android os.
Support soc sub-system, vop, edp, rga, audio, wifi and
so on.
Change-Id: Ia921769b81d4a74784bb3e638b2cb01111c621c9
Signed-off-by: Jianqun Xu <jay.xu@rock-chips.com>
If default phy pre-pll output pixclock is same to the requested rate,
the set_rate function is not called, inno->pixclock is zero and
make phy work not ok. This patch update inno->pixclock both in the
recalc_rate and set_rate, make pixclock be the real value.
Change-Id: Ifd4e145c499c2e82f96918ca62235627bf326734
Signed-off-by: Zheng Yang <zhengyang@rock-chips.com>
CABC(Content Adaptive Backlight Control) is used to
increase the contrast of such LCD-screens the backlight
can be (globally) dimmed when the image to be displayed
is dark (i.e. not comprising high intensity image data)
while the image data is numerically corrected and adapted
to the reduced backlight intensity.
Change-Id: I0bd84375264675943f1b601f0cac8b843567087d
Signed-off-by: Mark Yao <mark.yao@rock-chips.com>
Only 200MHz, 300MHz, 400MHz, 528MHz, 600MHz, 666MHz, 732MHz and
800MHz are available at present.
Change-Id: I3a376b389fe6b06b3b32f0c695de2cbde05dfeea
Signed-off-by: Finley Xiao <finley.xiao@rock-chips.com>
Replace "rockchip,rk33xx-lvds" with "rockchip,rk3368-lvds"
Change-Id: I065de5d994f167129591025e4251944478fa43e7
Signed-off-by: WeiYong Bi <bivvy.bi@rock-chips.com>
