This reverts commit 6b7fb9a6c9.
The audio regbank of hdmi-qp is drived by audio interface clk, and had
fixed by commits as follows:
[1] 3a7f369b5c ("arm64: dts: rockchip: rk3588: Add aud clk for hdmi nodes")
[2] e108ff9f6f ("drm/rockchip: dw_hdmi: Handle aud clk for hdmi qp")
OTOH, to make android hal happy, we still allow to access hdmi audio even
hdmi is plugged out.
"hdmi-audio-codec: ASoC: error at snd_soc_dai_startup on i2s-hifi: -19"
Android/Linux should reopen hdmi sound card depends on HPD plug event
to bring back to normal state.
Change-Id: I654fe18a04b750f57c8bd52ef4948a476bc1fa50
Signed-off-by: Sugar Zhang <sugar.zhang@rock-chips.com>
The separation of pinctrl and gpio drivers created a tiny window where
a pinconfig setting might produce a null-pointer dereference.
The affected device were rk3288-veyron devices in this case.
Pinctrl-hogs are claimed when the pinctrl driver is registered,
at which point their pinconfig settings will be applied.
At this time the now separate gpio devices will not have been created
yet and the matching driver won't have probed yet, making the gpio->foo()
call run into a null-ptr.
As probing is not really guaranteed to have been completed at a specific
time, introduce a queue that can hold the output settings until the gpio
driver has probed and will (in a separate patch) fetch the elements
of the list.
We expect the gpio driver to empty the list, but will nevertheless empty
it ourself on remove if that didn't happen.
Fixes: 9ce9a02039 ("pinctrl/rockchip: drop the gpio related codes")
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20210913224926.1260726-4-heiko@sntech.de
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
(cherry picked from commit e7165b1dff)
Signed-off-by: Jianqun Xu <jay.xu@rock-chips.com>
Change-Id: Id179c7eaacfb41565e2427ad82b55d11c2be8c4d
Some difference made during driver upstream review, this patch sync the
driver with upstream version.
Signed-off-by: Jianqun Xu <jay.xu@rock-chips.com>
Change-Id: I0da05d04f54bfc8e83afa28692c658b0b4d2604b
For GPIO0_B4 to GPIO0D7, the pinmux must read two registers.
Signed-off-by: Jianqun Xu <jay.xu@rock-chips.com>
Change-Id: Ic8d70c0ee56ce8ae8890a708cea84868f3a04228
Crypto only supports DMA32 address addressing and behaves
abnormally on more than 4G DDR.
Signed-off-by: Lin Jinhan <troy.lin@rock-chips.com>
Change-Id: I5b6b5c9eb5f00698d25e47a778f358380f4121eb
The K will be set 2 in YUV420 output mode, so we
don't need to handle YUV420 for DisplayPort.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Change-Id: I8f42536735e65c82705d58382f1db2b2994d741b
Make hwc work correct when handle a 8K input source
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Change-Id: I77ee3c13f5c884fbdd9eec72b02998e10bbc3425
IMX415 is supposed to be the default sensor on rk3588 evb boards.
Signed-off-by: Shunqian Zheng <zhengsq@rock-chips.com>
Change-Id: I4b2ea0f57c2510d46ea5c0b3416d536a2e7bc898
Just as the commit 25e44a6ed98b("bq25700: register otg vbus regulator")
said that there will be some problems with the current vbus control,
and the patch has registered the otg vbus regulator in the charger ic
driver, then the otg vbus regulator can be referenced in the fusb302 node.
Change-Id: Id4c9f866a3d131eee6f732300ff642a7f5489672
Signed-off-by: Wang Jie <dave.wang@rock-chips.com>
Set SSC Modulation rate to 31.2 KHz that can pass the compliance test
and have a better margin.
Signed-off-by: Frank Wang <frank.wang@rock-chips.com>
Change-Id: Iaf82e4803a9ccb196d21d9a02a93293be0dd053e
- Only check link retrain in short hpd pulse
- Always do link train in modeset
- Fix link retrain condition
- Add sink count check
Signed-off-by: Wyon Bi <bivvy.bi@rock-chips.com>
Change-Id: Ifed1d706dcda5ac79322271ec59c2f1a5a79262b
For Type-C PD driver using the tcpm framework and charger ic
(bq25700) output otg vbus solution. Because the dwc3 driver
cannot know whether the Type-C PD device sends DR_swap and
PR_swap messages, there are some problems with the charger ic
vbus control:
(1) rk3588s as sink, Type-C device sends DR_swap Message, u2phy driver
will send enable otg vbus notification to charger ic driver;
(2) After the Type-C device sends PR_swap Message to realize the
Sink->Source or Source->Sink switch, the charge ic driver cannot
dynamically enable or disable the otg vbus;
Based on the above problems, an otg vbus regulator is registered in
the charge ic driver for use by the fusb302 (Type-C PD controller chip)
driver, the otg vbus control is transferred to the tcpm framework.
In some cases (for example, the hardware does not have a PD chip),
in order to be compatible with switching from a lower version kernel
(kenrel-4.4/4.19) to a higher version kernel(kernel-5.10), dts will not
be modified. the software registration of the otg vbus regulator fails,
the vbus extcon mechanism will be registered.
Signed-off-by: Wang Jie <dave.wang@rock-chips.com>
Change-Id: I721abcb214795c0024e200b10ec3ab1d4a9b790a
Fixes: 7534ec9a51 ("arm64: dts: rockchip: rk806: bind the rk806 to the rk3588")
Signed-off-by: Tao Huang <huangtao@rock-chips.com>
Change-Id: I01cd29ea965fc3a03e68a02f1a6a18ad5c44a73c
slove following issues:
- socket buffer is over;
- store phyaddr;
- get max delayline value for rk3588;
- split mac setting and phy setting for loopback to fix flow;
- add rgmii-rxid interface loopback;
- enable mtl configuration for multi queue;
- use phy softreset instead of hard reset.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Change-Id: I8da5a42948b34bf4a256a6f425c0ed98590ddea6
