crypto and dmac share the same noc clk,
so mark the aclk_dmac1 as critical clk.
Change-Id: I34a4a7cc532a385086679fafb961a47b0a6abc3b
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
crypto and dmac share the same noc clk,
so mark the aclk_dmac_bus as critical clk.
Change-Id: Ib0b70bbed3fdefeab7b6f2b5f88350a416e66787
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
The serial Flash controller on the rk3036 would request
two clock nodes.
Change-Id: Iaa50c4a25602a68241b0b9b2f186e4c7e55bc3da
Signed-off-by: Randy Li <randy.li@rock-chips.com>
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
The power domains are supplied by regulators. Add support for them so
that the regulators are properly turned on before a domain is powered up
and turned off when a domain is powered down.
Change-Id: I43ad569e1b82a8e818cbbf2ffcfa6a965d993bbf
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
It's not need to power on all pd when add pm domain.
Use pd's real status for pm_genpd_init().
Change-Id: I9a976f01c1b0ff192e09494dcfa236d786495e96
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
This driver is modified to support RK1808 SoC.
Change-Id: Id622e126936a242f3dfbab94b0e7c7818b41f9ae
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
This patch set attempts to new compatible for thermal founding
on RK1808 SoCs.
Change-Id: I133218cd958e0aabf711a5d22fe5e5da2fbd59ce
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Based on the TSADC Tshut mode to select pinctrl,
instead of setting pinctrl based on architecture
(Not depends on pinctrl setting by "init" or "default").
And it requires setting the tshut polarity before select pinctrl.
Change-Id: Ieb181ec19dedbbfb7aef474b3558aac867e668eb
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
init temp_last with a more suitable value. also we eliminate
the steady state error by ajusting the temp calc fomular.
extra useful log is added to mark tsadc is probed successfully.
Change-Id: If88031c10646437fa7b5152c70aeaebf93e4df05
Signed-off-by: Rocky Hao <rocky.hao@rock-chips.com>
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
the mux_spdif_8ch_p is composed of spdif_8ch_src not spdif_8ch_pre
Change-Id: I7dd40e35078b2d012af2c777de763d14e93c3d4e
Signed-off-by: Xinhuang Li <buluess.li@rock-chips.com>
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
From Rockchips fractional divider usage, some clocks can be generated
by fractional divider, but the input clock frequency of fractional
divider should be less than a specified value.
Change-Id: Ifd6c5f6a24a64021f990506e8657cd925f9b96f9
Signed-off-by: Finley Xiao <finley.xiao@rock-chips.com>
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
If change parent to alternate parent and the old parent clock speed is less
than the clock speed of the alternate parent, add dividers first and then
select alternate parent.
If change parent to primary parent, select primary parent first and then
remove dividers.
Change-Id: Ib82de9a936effe5c885639799f3bb5629dc89f8d
Signed-off-by: Finley Xiao <finley.xiao@rock-chips.com>
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Tsadc has a tshut pin which is designed to reset the pmic or soc,
when the temperature inside soc is too high. we should switch off
the tshut function and change the pin to gpio function in reboot
process, eg, software reset. If not, the tsadc module will WRONGLY
pull high the tshut pin during its reset process and then WRONGLY
reset the pmic or soc, which incurred a hardware reset. The hardware
reset will reset everything inside soc, even includes the power on
reason flag, which is set by software before reboot process.
we also change over-temperature protection mode to cru mode,
since the tshut pin have be changed to gpio function.
Change-Id: Iac3dacf55a4b5536fccd2eb05a6a9e6923a082c0
Signed-off-by: Rocky Hao <rocky.hao@rock-chips.com>
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Prevent the system from entering suspend when usb cable is connecetd.
Change-Id: I50c4a09d9142ebeb2d4e2a0ab2df59f98ef99737
Signed-off-by: Frank Wang <frank.wang@rock-chips.com>
This patch adds bypass uart cfgs for rk1808 USB 3.0 OTG
port. In addition, please note that it needs to set the
uart2 rx/tx io selection in the reg "BUS_GRF_IOFUNC_CON0"
bit 15:14.
Change-Id: I77ea461be299c0454f5caee1349110b6f2714c30
Signed-off-by: William Wu <william.wu@rock-chips.com>
Signed-off-by: Frank Wang <frank.wang@rock-chips.com>
RK1808 SoC has an usb 2.0 comb phy with one otg-port and one
host-port. This patch adds port configurations for them.
Change-Id: Id4d117929ec0e327c8f2cc1a06d4caaa2d584f06
Signed-off-by: William Wu <william.wu@rock-chips.com>
Signed-off-by: Frank Wang <frank.wang@rock-chips.com>
We find an usb phy 480MHz clk prepare fail issue on PX30/RK3326
platforms with RK819 PMIC. On PX30/RK3326 platforms, we set the
usb480m clk to critical because GPU 480M is from usb480m and the
source clocks should be always on. And the usb phy 480MHz clk is
parent of usb480m clk, so the clk framework will prepare the usb
phy 480MHz clk when register it.
This logic works well if the usb phy probe only once. But if the
usb phy needs to probe twice or more because of some reasons (e.g.
fail to get vbus regulator from RK819), the usb phy 480MHz clk will
be unregistered and registered again, however, the clk framework
doesn't prepare the usb phy 480MHz clk except the first time register
operation. So we move the 480MHz clk register to the end of probe,
and make sure only register it once.
Change-Id: If69378b49035746a7c0107c6a363c4d91dfc15e5
Signed-off-by: William Wu <william.wu@rock-chips.com>
Signed-off-by: Bin Yang <yangbin@rock-chips.com>
Signed-off-by: Frank Wang <frank.wang@rock-chips.com>
This patch adds rk3368 otg-port phy configurations.
But actually, we don't use the otg phy configurations
for the time being, because we use dwc_otg_310 driver
for rk3368 otg controller, and this driver doesn't use
generic phy. This patch is useful if we switch to dwc2
driver for rk3368 otg in the feature.
Change-Id: Ibed3fde4ef64ad25e933ac4560f956b7c9f5c476
Signed-off-by: William Wu <william.wu@rock-chips.com>
Signed-off-by: Frank Wang <frank.wang@rock-chips.com>
Because USB OTG id irq is disabled during system suspend
and enabled after resume, so the usb2 phy doesn't notice
any id status change upon resume. It may cause two issues:
1. Plug in OTG cable and USB device when system enter
suspend, it will fail to detect the OTG cable and
USB device after resume.
2. Plug out OTG cable and USB device when system enter
suspend, and then connect USB to PC or USB charger
after resume, it will fail to detect USB charge type.
This patch restores the OTG id status before enter suspend，
and check the id status upon resume, and set the extcon
state and vbus if id status has changed.
Change-Id: Iaca14841cc287e7d82e1cffd64ff18bba86d3ba4
Signed-off-by: William Wu <william.wu@rock-chips.com>
Signed-off-by: Frank Wang <frank.wang@rock-chips.com>
The controller will be reinit when suspend and resume in device
mode if not connect to PC. And the U2PHY must be keep in power
on state during the init process. But The 'otg_sm_work' may be
schedule immediately and power off the U2PHY if system suspend
and resume between the delay time of schedule 'otg_sm_work', so
it will result in the error when init controller as below:
dwc2_core_reset() HANG! Soft Reset GRSTCTL=80000001
So flush the otg work in exit function to finish power control
of U2PHY.
Change-Id: I79c4b6a877196abd2f2201b2f984c9ea22e48fec
Signed-off-by: Meng Dongyang <daniel.meng@rock-chips.com>
Signed-off-by: Frank Wang <frank.wang@rock-chips.com>
This patches fixes comparison between signed and unsigned values.
Change-Id: Ie417fdb8092463890a67bce7efa11f3ef20d5871
Signed-off-by: William Wu <william.wu@rock-chips.com>
Signed-off-by: Frank Wang <frank.wang@rock-chips.com>
This patch fix the following clang warning:
[clang]drivers/phy/rockchip/phy-rockchip-inno-usb2.c:1255:3:
warning: Value stored to 'delay' is never read
Change-Id: I8c70975e1bc2b24a78d0934ccefc9d67fe3a5da9
Signed-off-by: William Wu <william.wu@rock-chips.com>
Signed-off-by: Frank Wang <frank.wang@rock-chips.com>
Reduce the otg schedule delay time from 6s to 1s to do
the first time usb charger detection earlier when power
on system with usb cable connect to PC USB. Because the
usb connection willed be disconnectted during usb charger
detection.
And the patch also makes the phy detect the usb disconnetion
more quickly after usb cable plug out.
Change-Id: I9b55317ab3592f517fdf590fea85c4ed403bbd8d
Signed-off-by: William Wu <william.wu@rock-chips.com>
Signed-off-by: Frank Wang <frank.wang@rock-chips.com>
Open pre-emphasize in non-chirp state for rk3228 USB
PHY0 otg port to increase HS slew rate.
Change-Id: Ia565746286a750a251619a83cbbead99c0ddecbd
Signed-off-by: William Wu <william.wu@rock-chips.com>
Signed-off-by: Frank Wang <frank.wang@rock-chips.com>
Make u2phy enter low power mode when suspend. If config the DT of
u2phy port with "rockchip,low-power-mode" property, the port will
be config to lower power state when suspend.
Bvalid irq and linestate irq will be disabled in this mode.
Change-Id: Ie7d40a9a181b0622b1f8d062a741661548cabd59
Signed-off-by: Meng Dongyang <daniel.meng@rock-chips.com>
Signed-off-by: Frank Wang <frank.wang@rock-chips.com>
Open pre-emphasize in non-chirp state for rk3308 and
rk3328 usb otg and host ports to increase HS slew rate.
Change-Id: I16435d67b9994cef0fd5e6edbae00c41cc02c48b
Signed-off-by: William Wu <william.wu@rock-chips.com>
Signed-off-by: Frank Wang <frank.wang@rock-chips.com>
